- 14 Aug, 2009 40 commits
-
-
Johannes Berg authored
Add some more documentation including an example so that it's clearer what should be done for TX retries. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
In order for userspace to be able to figure out whether it obtained a consistent snapshot of data or not when using netlink dumps, we need to have a generation number in each dump message that indicates whether the list has changed or not -- its value is arbitrary. This patch adds such a number to all dumps, this needs some mac80211 involvement to keep track of a generation number to start with when adding/removing mesh paths or stations. The wiphy and netdev lists can be fully handled within cfg80211, of course, but generation numbers need to be stored there as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
With the move of everything related to the SME from mac80211 to cfg80211, we lost the ability to send reassociation frames. This adds them back, but only for wireless extensions. With the userspace SME, it shall control assoc vs. reassoc (it already can do so with the nl80211 interface). I haven't touched the connect() implementation, so it is not possible to reassociate with the nl80211 connect primitive. I think that should be done with the NL80211_CMD_ROAM command, but we'll have to see how that can be handled in the future, especially with fullmac chips. This patch addresses only the immediate regression we had in mac80211, which previously sent reassoc. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Currently, there's a problem that affects regulatory enforcement and connection stability, in that it is possible to switch the channel while connected to a network or joined to an IBSS. The problem comes from the fact that we only validate the channel against the current interface's type, not against any other interface. Thus, you have any type of interface up, additionally bring up a monitor mode interface and switch the channel on the monitor. This will obviously also switch the channel on the other interface. The problem now is that if you do that while sending beacons for IBSS mode, you can switch to a disabled channel or a channel that doesn't allow beaconing. Combined with a managed mode interface connected to an AP instead of an IBSS interface, you can easily break the connection that way. To fix this, this patch validates any channel change with all available interfaces, and disallows such changes on secondary interfaces if another interface is connected to an AP or joined to an IBSS. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Commit 9cef8737 "mac80211: fix managed mode BSSID handling" broke association in wl1251, most probably because the driver configured the bssid filter incorrectly. Workaround this by disabling filter altogether. This needs to be fixed properly soon. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
The logs currently don't show when hw scan has completed, fix that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Luciano is maintaining wl1271 part. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Now that wl1271 doesn't use reg.h anymore, it can be renamed to wl1251_reg.h. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
wl1251 should use workqueue created by mac80211 to not block the events workqueue too long. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
It should not be hidden inside wl1251_cmd_ps_mode(). Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
There is a bug in wl1251_op_config(). It was calling join with previous channel. Fix it by setting assigning wl->channel before calling join command. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Better to use wl1251_cmd_join() only for sending the command and move the logic to wl1251_join(). Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Because join channel tunes to a channel, better to make it more obvious by adding a parameter for it. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Because wl->channel was initialised to one, the first join command in wl1251_op_config() always failed. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
We should wait everytime for the join command to finish, not waiting for it might create problems. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
wl1251 was using hardcoded beacon intervals and dtim periods, use the ones provided by mac80211 instead. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
It's more common to have beacon interval before dtim period. Also use bool instead of u8. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
Now wl1271 is splitted to separate files, no need to use wl1251_ops anymore. So remove struct wl1251_chip and wl1251_ops.c. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
In SDIO, the host driver requests the IRQ and invokes a callback to the card driver. This differs from SPI, so the relevant code needs to be interface-specific. This patch pushes the irq code down into _spi.c and _sdio.c, and adds enable/disable callbacks. This fixes the following warning: [ 566.343887] ------------[ cut here ]------------ [ 566.349105] WARNING: at kernel/irq/manage.c:222 __enable_irq+0x3c/0x6c() [ 566.356735] Unbalanced enable for IRQ 0 [ 566.361099] Modules linked in: msm_wifi wl12xx_sdio wl12xx mac80211 cfg80211 rfkill_backport lib80211_crypt_ccmp lib80211_crypt_wep lib80211_crypt_tkip lib80211 [ 566.381240] [<c025acec>] (dump_stack+0x0/0x14) from [<c004b610>] (warn_slowpath+0x70/0x8c) [ 566.391860] [<c004b5a0>] (warn_slowpath+0x0/0x8c) from [<c0077c10>] (__enable_irq+0x3c/0x6c) [ 566.402572] r3:00000000 r2:c02cad13 [ 566.407516] r7:00001002 r6:00000000 r5:c0310be4 r4:c0310be4 [ 566.415786] [<c0077bd4>] (__enable_irq+0x0/0x6c) from [<c0077fd0>] (enable_irq+0x38/0x64) [ 566.425826] r5:c0310be4 r4:a0000013 [ 566.430709] [<c0077f98>] (enable_irq+0x0/0x64) from [<bf0dfa78>] (wl12xx_boot_run_firmware+0xfc/0x170 [wl12xx]) [ 566.442947] r7:00001002 r6:c440a9fc r5:00000072 r4:c440a9e0 [ 566.450851] [<bf0df97c>] (wl12xx_boot_run_firmware+0x0/0x170 [wl12xx]) from [<bf0e05f0>] (wl1251_boot+0xd4/0x108 [wl12xx]) [ 566.464492] r5:00000000 r4:c440a9e0 [ 566.469466] [<bf0e051c>] (wl1251_boot+0x0/0x108 [wl12xx]) from [<bf0dd27c>] (wl12xx_op_start+0x54/0xb8 [wl12xx]) [ 566.482162] r5:00000000 r4:c440a9e0 [ 566.487472] [<bf0dd228>] (wl12xx_op_start+0x0/0xb8 [wl12xx]) from [<bf0b96dc>] (ieee80211_open+0x2dc/0x720 [mac80211]) [ 566.500594] r7:00001002 r6:c4950800 r5:c440a220 r4:00000000 [ 566.508865] [<bf0b9400>] (ieee80211_open+0x0/0x720 [mac80211]) from [<c01f1edc>] (dev_open+0x9c/0xfc) [ 566.520705] [<c01f1e40>] (dev_open+0x0/0xfc) from [<c01f17dc>] (dev_change_flags+0x98/0x170) [ 566.531417] r5:00000041 r4:c4950800 [ 566.536330] [<c01f1744>] (dev_change_flags+0x0/0x170) from [<c023041c>] (devinet_ioctl+0x3a8/0x784) [ 566.547683] r7:c128e380 r6:00000001 r5:00008914 r4:00000000 [ 566.555587] [<c0230074>] (devinet_ioctl+0x0/0x784) from [<c02318cc>] (inet_ioctl+0xdc/0x114) [ 566.566299] [<c02317f0>] (inet_ioctl+0x0/0x114) from [<c01e1a60>] (sock_ioctl+0x1f0/0x248) [ 566.576827] r5:00008914 r4:c572c1a0 [ 566.581771] [<c01e1870>] (sock_ioctl+0x0/0x248) from [<c00b23a0>] (vfs_ioctl+0x34/0x94) [ 566.592086] r7:c572c1a0 r6:bee497e8 r5:00008914 r4:c572c1a0 [ 566.599990] [<c00b236c>] (vfs_ioctl+0x0/0x94) from [<c00b2a28>] (do_vfs_ioctl+0x52c/0x584) [ 566.610549] r7:c572c1a0 r6:00008914 r5:c572c1a0 r4:c3201228 [ 566.618453] [<c00b24fc>] (do_vfs_ioctl+0x0/0x584) from [<c00b2ac0>] (sys_ioctl+0x40/0x64) [ 566.628890] [<c00b2a80>] (sys_ioctl+0x0/0x64) from [<c0021da0>] (ret_fast_syscall+0x0/0x2c) [ 566.639541] r7:00000036 r6:00000000 r5:00000004 r4:001a11f3 [ 566.647445] ---[ end trace 15c26ef7dd5e7b03 ]--- Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
This adds the wl1251_sdio module, enabling the SDIO interface for wl1251, as used by the Google G1 phone and others. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
This creates a module called wl1251_spi.ko which contains just the SPI-specific code. The core remains in the module wl1251.ko. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
This change moves all of the spi specific code from main.c into spi.c. The module initialization code also moves, but common code for initializing mac80211 etc. stays in main.c, as this will eventually form a common library module also used by wl1251_sdio. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
The same partition setting code can be used for both SPI and SDIO modes, if we remove the spi-specific commands and use the more generic buffer write routines. Do that and move it to io.c since it deals with register/memory address offsets. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
Introduce an ops struct with read, write, and reset functions to abstract away the details of the wl1251 bus interface. Doing this will allow SDIO to coexist with SPI by supplying its own I/O routines. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
Remove a dependency on the bus-specific struct device by using wiphy_dev when requesting firmware. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
In order to eventually support wl1251 spi and sdio interfaces, move the register and memory transfer functions to a common file. Also rename wl1251_spi_mem_{read,write} to indicate its common usage. We still use spi_read internally until SDIO interface is introduced so nothing functional should change here. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kalle Valo authored
The fixed addresses are not used in wl1251, only in wl1271. So it can be safely removed. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
ANI uses the beacon RSSI for its operation. Update this properly. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
The chainmask can be obtained directly from ath_hw. Also, use a helper macro for comparing CTLs - this improves readability. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Write CCK power-per-rate array always and report correct TX power to regulatory. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
This patch revamps the antenna configuration mechanism for 4K chips. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
A subsequent patch would use these for configuring antennae on AR9285. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
regChainOffset is always zero, remove it. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c This improves maintainability. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
We have never used these at all. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith authored
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Samuel Ortiz authored
With iwconfig there is no way to properly set the ciphers when trying to connect to a WEP SSID. Although mac80211 based drivers dont need it, several fullmac drivers do. This patch basically sets the WEP ciphers whenever they're not set at all. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
When an AP disassociates us, we currently go into a weird state because the SME doesn't handle authenticated but not associated well unless it's within its own state machine, it can't recover from that. However, it shouldn't need to, since we don't do any decisions in it really -- so when we get disconnected, simply deauthenticate too. Reported-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-