- 20 Nov, 2016 40 commits
-
-
Jack Morgenstein authored
commit 8ec07bf8 upstream. When sending QP1 MAD packets which use a GRH, the source GID (which consists of the 64-bit subnet prefix, and the 64 bit port GUID) must be included in the packet GRH. For SR-IOV, a GID cache is used, since the source GID needs to be the slave's source GID, and not the Hypervisor's GID. This cache also included a subnet_prefix. Unfortunately, the subnet_prefix field in the cache was never initialized (to the default subnet prefix 0xfe80::0). As a result, this field remained all zeroes. Therefore, when SR-IOV was active, all QP1 packets which included a GRH had a source GID subnet prefix of all-zeroes. However, the subnet-prefix should initially be 0xfe80::0 (the default subnet prefix). In addition, if OpenSM modifies a port's subnet prefix, the new subnet prefix must be used in the GRH when sending QP1 packets. To fix this we now initialize the subnet prefix in the SR-IOV GID cache to the default subnet prefix. We update the cached value if/when OpenSM modifies the port's subnet prefix. We take this cached value when sending QP1 packets when SR-IOV is active. Note that the value is stored as an atomic64. This eliminates any need for locking when the subnet prefix is being updated. Note also that we depend on the FW generating the "port management change" event for tracking subnet-prefix changes performed by OpenSM. If running early FW (before 2.9.4630), subnet prefix changes will not be tracked (but the default subnet prefix still will be stored in the cache; therefore users who do not modify the subnet prefix will not have a problem). IF there is a need for such tracking also for early FW, we will add that capability in a subsequent patch. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Jack Morgenstein authored
commit baa0be70 upstream. The indentation in the QP1 GRH flow in procedure build_mlx_header is really confusing. Fix it, in preparation for a commit which touches this code. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
-
Alex Vesker authored
commit e5ac40cd upstream. Because of an incorrect bit-masking done on the join state bits, when handling a join request we failed to detect a difference between the group join state and the request join state when joining as send only full member (0x8). This caused the MC join request not to be sent. This issue is relevant only when SRIOV is enabled and SM supports send only full member. This fix separates scope bits and join states bits a nibble each. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
-
Alex Vesker authored
commit 344bacca upstream. This fix solves a race between light flush and on the fly joins. Light flush doesn't set the device to down and unset IPOIB_OPER_UP flag, this means that if while flushing we have a MC join in progress and the QP was attached to BC MGID we can have a mismatches when re-attaching a QP to the BC MGID. The light flush would set the broadcast group to NULL causing an on the fly join to rejoin and reattach to the BC MCG as well as adding the BC MGID to the multicast list. The flush process would later on remove the BC MGID and detach it from the QP. On the next flush the BC MGID is present in the multicast list but not found when trying to detach it because of the previous double attach and single detach. [18332.714265] ------------[ cut here ]------------ [18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core] ... [18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 [18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000 [18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300 [18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280 [18332.796199] Call Trace: [18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c [18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0 [18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20 [18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core] [18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib] [18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib] [18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib] [18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib] [18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0 [18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40 [18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80 [18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib] [18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib] [18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30 [18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50 [18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170 [18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0 [18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50 [18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0 [18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0 [18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0 [18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25 [18332.894727] ---[ end trace 09ebbe31f831ef17 ]--- Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events") Signed-off-by:
-
Alan Stern authored
commit 08c5cd37 upstream. Some full-speed mceusb infrared transceivers contain invalid endpoint descriptors for their interrupt endpoints, with bInterval set to 0. In the past they have worked out okay with the mceusb driver, because the driver sets the bInterval field in the descriptor to 1, overwriting whatever value may have been there before. However, this approach was never sanctioned by the USB core, and in fact it does not work with xHCI controllers, because they use the bInterval value that was present when the configuration was installed. Currently usbcore uses 32 ms as the default interval if the value in the endpoint descriptor is invalid. It turns out that these IR transceivers don't work properly unless the interval is set to 10 ms or below. To work around this mceusb problem, this patch changes the endpoint-descriptor parsing routine, making the default interval value be 10 ms rather than 32 ms. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
Wade Berrier <wberrier@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Matt Fleming authored
commit 080fe0b7 upstream. While the Intel PMU monitors the LLC when perf enables the HW_CACHE_REFERENCES and HW_CACHE_MISSES events, these events monitor L1 instruction cache fetches (0x0080) and instruction cache misses (0x0081) on the AMD PMU. This is extremely confusing when monitoring the same workload across Intel and AMD machines, since parameters like, $ perf stat -e cache-references,cache-misses measure completely different things. Instead, make the AMD PMU measure instruction/data cache and TLB fill requests to the L2 and instruction/data cache and TLB misses in the L2 when HW_CACHE_REFERENCES and HW_CACHE_MISSES are enabled, respectively. That way the events measure unified caches on both platforms. Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Acked-by:
Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1472044328-21302-1-git-send-email-matt@codeblueprint.co.ukSigned-off-by:
Ingo Molnar <mingo@kernel.org> [bwh: Backported to 3.16: - Drop KVM PMU changes - Adjust filename] Signed-off-by:
-
Al Viro authored
commit 8630c322 upstream. really ugly, but apparently avr32 compilers turns access_ok() into something so bad that they want it in assembler. Left that way, zeroing added in inline wrapper. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit e98b9e37 upstream. Signed-off-by:
-
Al Viro authored
commit d0cf3851 upstream. Signed-off-by:
-
Al Viro authored
commit c90a3bc5 upstream. Signed-off-by:
-
Al Viro authored
commit 8f035983 upstream. Signed-off-by:
-
Al Viro authored
commit 917400ce upstream. Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Al Viro authored
commit 6e050503 upstream. Signed-off-by:
-
Al Viro authored
commit c6852389 upstream. It could be done in exception-handling bits in __get_user_b() et.al., but the surgery involved would take more knowledge of sh64 details than I have or _want_ to have. Signed-off-by:
-
Al Viro authored
commit b615e3c7 upstream. Signed-off-by:
-
Al Viro authored
commit c2f18fa4 upstream. * should zero on any failure * __get_user() should use __copy_from_user(), not copy_from_user() Signed-off-by:
-
Al Viro authored
commit fd2d2b19 upstream. Signed-off-by:
-
Al Viro authored
commit 22426465 upstream. should clear on access_ok() failures. Also remove the useless range truncation logics. Signed-off-by:
-
Al Viro authored
commit aace880f upstream. Signed-off-by:
-
Al Viro authored
commit acb2505d upstream. ... that should zero on faults. Also remove the <censored> helpful logics wrt range truncation copied from ppc32. Where it had ever been needed only in case of copy_from_user() *and* had not been merged into the mainline until a month after the need had disappeared. A decade before openrisc went into mainline, I might add... Signed-off-by:
-
Al Viro authored
commit ae7cc577 upstream. Signed-off-by:
-
Al Viro authored
commit 43403eab upstream. Signed-off-by:
-
Al Viro authored
commit e69d7005 upstream. Signed-off-by:
-
Vineet Gupta authored
commit 05d9d0b9 upstream. Al reported potential issue with ARC get_user() as it wasn't clearing out destination pointer in case of fault due to bad address etc. Verified using following | { | u32 bogus1 = 0xdeadbeef; | u64 bogus2 = 0xdead; | int rc1, rc2; | | pr_info("Orig values %x %llx\n", bogus1, bogus2); | rc1 = get_user(bogus1, (u32 __user *)0x40000000); | rc2 = get_user(bogus2, (u64 __user *)0x50000000); | pr_info("access %d %d, new values %x %llx\n", | rc1, rc2, bogus1, bogus2); | } | [ARCLinux]# insmod /mnt/kernel-module/qtn.ko | Orig values deadbeef dead | access -14 -14, new values 0 0 Reported-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Al Viro authored
commit 8ae95ed4 upstream. Acked-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Al Viro authored
commit a5e541f7 upstream. Signed-off-by:
-
Al Viro authored
commit f35c1e06 upstream. It's -EFAULT, not -1 (and contrary to the comment in there, __strnlen_user() can return 0 - on faults). Acked-by:
Richard Kuo <rkuo@codeaurora.org> Signed-off-by:
-
Al Viro authored
commit 3b8767a8 upstream. It should check access_ok(). Otherwise a bunch of places turn into trivially exploitable rootholes. Signed-off-by:
-
Al Viro authored
commit eb47e029 upstream. * copy_from_user() on access_ok() failure ought to zero the destination * none of those primitives should skip the access_ok() check in case of small constant size. Acked-by:
Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by:
-
Al Viro authored
commit 9ad18b75 upstream. both for access_ok() failures and for faults halfway through Signed-off-by:
-
Johannes Berg authored
commit ad5987b4 upstream. Due to an apparent copy/paste bug, the number of counters for the beacon configuration were checked twice, instead of checking the number of probe response counters. Fix this to check the number of probe response counters before parsing those. Fixes: 9a774c78 ("cfg80211: Support multiple CSA counters") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Matt Redfearn authored
commit 951c39cd upstream. If the paravirt machine is compiles without CONFIG_SMP, the following linker error occurs arch/mips/kernel/head.o: In function `kernel_entry': (.ref.text+0x10): undefined reference to `smp_bootstrap' due to the kernel entry macro always including SMP startup code. Wrap this code in CONFIG_SMP to fix the error. Signed-off-by:
Matt Redfearn <matt.redfearn@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14212/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Ard Biesheuvel authored
commit 2db34e78 upstream. The AES-CTR glue code avoids calling into the blkcipher API for the tail portion of the walk, by comparing the remainder of walk.nbytes modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight into the tail processing block if they are equal. This tail processing block checks whether nbytes != 0, and does nothing otherwise. However, in case of an allocation failure in the blkcipher layer, we may enter this code with walk.nbytes == 0, while nbytes > 0. In this case, we should not dereference the source and destination pointers, since they may be NULL. So instead of checking for nbytes != 0, check for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in non-error conditions. Fixes: 49788fe2 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions") Reported-by:
xiakaixu <xiakaixu@huawei.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
commit acdb04d0 upstream. When we need to allocate a temporary blkcipher_walk_next and it fails, the code is supposed to take the slow path of processing the data block by block. However, due to an unrelated change we instead end up dereferencing the NULL pointer. This patch fixes it by moving the unrelated bsize setting out of the way so that we enter the slow path as inteded. Fixes: 7607bd8f ("[CRYPTO] blkcipher: Added blkcipher_walk_virt_block") Reported-by:
-
Russell King authored
commit 06dfe5cc upstream. SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for the PCMCIA socket class. PCMCIA used to handle suspend/resume via the socket hosting device, which happened at normal device suspend/resume time. However, the referenced commit changed this: much of the resume now happens much earlier, in the noirq resume handler of dev_pm_ops. However, on SA1111, the PCMCIA device is not accessible as the SA1111 has not been resumed at _noirq time. It's slightly worse than that, because the SA1111 has already been put to sleep at _noirq time, so suspend doesn't work properly. Fix this by converting the core SA1111 code to use dev_pm_ops as well, and performing its own suspend/resume at noirq time. This fixes these errors in the kernel log: pcmcia_socket pcmcia_socket0: time out after reset pcmcia_socket pcmcia_socket1: time out after reset and the resulting lack of PCMCIA cards after a S2RAM cycle. Fixes: d7646f76 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Daniele Palmas authored
commit f190fd92 upstream. This patch adds support for Infineon flashloader 0x8087/0x0801. The flashloader is used in Telit LE940B modem family with Telit flashing application. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Trond Myklebust authored
commit b519d408 upstream. Ensure that we conform to the algorithm described in RFC5661, section 18.36.4 for when to bump the sequence id. In essence we do it for all cases except when the RPC call timed out, or in case of the server returning NFS4ERR_DELAY or NFS4ERR_STALE_CLIENTID. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [bwh: Backported to 3.16: - Add the 'out' label - Adjust context] Signed-off-by:
-
Karl Beldan authored
commit f6d7c1b5 upstream. This fixes subpage writes when using 4-bit HW ECC. There has been numerous reports about ECC errors with devices using this driver for a while. Also the 4-bit ECC has been reported as broken with subpages in [1] and with 16 bits NANDs in the driver and in mach* board files both in mainline and in the vendor BSPs. What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to try reinitializing the ECC engine: - R/W on whole pages properly generates/checks RS code - try writing the 1st subpage only of a blank page, the subpage is well written and the RS code properly generated, re-reading the same page the HW detects some ECC error, reading the same page again no ECC error is detected Note that the ECC engine is already reinitialized in the 1-bit case. Tested on my LCDK with UBI+UBIFS using subpages. This could potentially get rid of the issue workarounded in [1]. [1] 28c015a9 ("mtd: davinci-nand: disable subpage write for keystone-nand") Fixes: 6a4123e5 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage") Signed-off-by:
Karl Beldan <kbeldan@baylibre.com> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Al Viro authored
commit 2545e5da upstream. ... in all cases, including the failing access_ok() Note that some architectures using asm-generic/uaccess.h have __copy_from_user() not zeroing the tail on failure halfway through. This variant works either way. Signed-off-by:
-
Al Viro authored
commit 2561d309 upstream. it should clear the destination even when access_ok() fails. Signed-off-by:
-
