Use sign_extend32 kernel function instead of code duplication.
This function is also safe for 16 bits.
Signed-off-by: Karim Eshapa <karim.eshapa@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Checkpatch.pl complains about function pointer parameter names missing.

Add parameter names.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

AD5311R is a single channel DAC with 10-bit precision and i2c interface.
The device includes a 2.5V internal reference which is enabled by default.

This device is similar to AD5691R/AD5692R/AD5693/AD5693R, the only
difference is that it has 10-bit precision.

Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310R_5311R.pdfSigned-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Added defines for channel consumer device-tree binding
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This adds a generic resistive touchscreen (GRTS) driver, which is based
on an IIO device (an ADC). It must be connected to the channels of an ADC
to receive touch data. Then it will feed the data into the input subsystem
where it registers an input device.
It uses an IIO callback buffer to register to the IIO device

Some parts of this patch are based on initial original work by
Mohamed Jamsheeth Hajanajubudeen and Bandaru Venkateswara Swamy
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This implements the support for position and pressure for the included
touchscreen support in the SAMA5D2 SOC ADC block.
Two position channels are added and one for pressure.
They can be read in raw format, or through a buffer.
A normal use case is for a consumer driver to register a callback buffer
for these channels.
When the touchscreen channels are in the active scan mask,
the driver will start the touchscreen sampling and push the data to the
buffer.

Some parts of this patch are based on initial original work by
Mohamed Jamsheeth Hajanajubudeen and Bandaru Venkateswara Swamy
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Added bindings for generic resistive touchscreen ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a common touchscreen optional property that will specify
the minimum pressure applied to the screen that is needed
such that the driver will report the touch event.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add new channel type for relative position on a pad.

These type of analog sensor offers the position of a pen
on a touchpad, and is represented as a voltage, which can be
converted to a position on X and Y axis on the pad.
The channel will hand the relative position on the pad in both directions.

The channel can then be consumed by a touchscreen driver or
read as-is for a raw indication of the touchpen on a touchpad.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add MAINTAINERS entry for generic resistive touchscreen adc
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This part has been declared "not for new designs". It is now
difficult to obtain and we have had no-one come forward with hardware
making it difficult to proceed with the necessary work to move this
driver out of staging.

The device uses two separate chip selects and would require locking
between them which is thought to be difficult to enforce without
non trivial changes in the SPI subsystem.  This work simply isn't worth
doing given the status of the part and the fact no one seems to have
gone for a similar hardware design since this one.

If anyone does have access to one of these and is willing to contribute
the time necessary then we can reevaluate dropping the driver.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Check validity of interrupt timestamps by computing time between
2 interrupts. If it matches the chip frequency modulo 4%, it is
used as the data timestamp and also for estimating the chip
frequency measured from the system. Otherwise timestamp is
computed using the estimated chip frequency.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds several register and bit defines to help improve the
clarity of the code by cleaning up magic numbers throughout the driver.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use fifo overflow bit from int status rather than using an
arbitrary threshold.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use unaligned access since buffer is a bytes table. Truncate fifo
count to read only complete datum.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Instead of storing fifo rate in Hz, store the chip internal sample
rate divider. This will be more useful for timestamping. There
are both equivalent.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Using a fifo for storing timestamps is useless since the interrupt
is in one-shot mode, preventing the hard irq handler to be called
when the irq thread is running. Instead use the generic timestamp
function iio_pollfunc_store_time.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We can't call regmap_irq_get_virq() unless the regmap-irq support
is enabled:

drivers/iio/adc/sun4i-gpadc-iio.o: In function `sun4i_irq_init':
sun4i-gpadc-iio.c:(.text+0x59c): undefined reference to `regmap_irq_get_virq'

I came across this in a randconfig build now, but I guess this is
a much older problem that I simply never hit before because regmap_irq
is usually enabled by one of the other drivers that need it.

Fixes: d1caa990 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The reset flags operation is selected by bit 2 in the "Reset and Load
Signals Decoders" register, not bit 1.

Fixes: 28e5d3bb ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Merge proc_cmdline simplifications.

This re-writes the get_mm_cmdline() logic to be rather simpler than it
used to be, and makes the semantics for "cmdline goes past the end of
the original area" more natural.

You _can_ use prctl(PR_SET_MM) to just point your command line somewhere
else entirely, but the traditional model is to just edit things in place
and that still needs to continue to work.  At least this way the code
makes some sense.

* proc-cmdline:
  fs/proc: simplify and clarify get_mm_cmdline() function
  fs/proc: re-factor proc_pid_cmdline_read() a bit

Use the error code EUCLEAN for filesystem errors because other
filesystems use this code too.

[ And remove unused EMEMERROR  - Linus ]
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull power supply and reset updates from Sebastian Reichel:
 - bq27xxx: Add BQ27426 support
 - ab8500: Drop AB8540/9540 support
 - Introduced new usb_type property
 - Properly document the power-supply ABI
 - misc. cleanups and fixes

* tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  MAINTAINERS: add entry for LEGO MINDSTORMS EV3
  power: supply: ab8500_charger: fix spelling mistake: "faile" -> "failed"
  power: supply: axp288_fuel_gauge: Remove polling from the driver
  power: supply: axp288_fuelguage: Do not bind when the fg function is not used
  power: supply: axp288_charger: Do not bind when the charge function is not used
  power: supply: axp288_charger: Support 3500 and 4000 mA input current limit
  power: supply: s3c-adc-battery: fix driver data initialization
  power: supply: charger-manager: Verify polling interval only when polling requested
  power: supply: sysfs: Use enum to specify property
  power: supply: ab8500: Drop AB8540/9540 support
  power: supply: ab8500_fg: fix spelling mistake: "Disharge" -> "Discharge"
  power: supply: simplify getting .drvdata
  power: supply: bq27xxx: Add support for BQ27426
  gpio-poweroff: Use gpiod_set_value_cansleep

Pull HSI update from Sebastian Reichel:
 "Just one patch for the HSI subsystem this time: use the new vm_fault_t
  return type"

* tag 'hsi-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  hsi: clients: Change return type to vm_fault_t

Pull clk updates from Stephen Boyd:
 "This time we have a good set of changes to the core framework that do
  some general cleanups, but nothing too major. The majority of the diff
  goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
  introduced for Actions Semi so it takes up some lines to add all the
  different types, and the Qualcomm diff is there because we add support
  for two SoCs and it's quite a bit of data.

  Otherwise the big driver updates are on TI Davinci and Amlogic
  platforms. And then the long tail of driver updates for various fixes
  and stuff follows after that.

  Core:
   - debugfs cleanups removing error checking and an unused provider API
   - Removal of a clk init typedef that isn't used
   - Usage of match_string() to simplify parent string name matching
   - OF clk helpers moved to their own file (linux/of_clk.h)
   - Make clk warnings more readable across kernel versions

  New Drivers:
   - Qualcomm SDM845 GCC and Video clk controllers
   - Qualcomm MSM8998 GCC
   - Actions Semi S900 SoC support
   - Nuvoton npcm750 microcontroller clks
   - Amlogic axg AO clock controller

  Removed Drivers:
   - Deprecated Rockchip clk-gate driver

  Updates:
   - debugfs functions stopped checking return values
   - Support for the MSIOF module clocks on Rensas R-Car M3-N
   - Support for the new Rensas RZ/G1C and R-Car E3 SoCs
   - Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
   - Berlin and Amlogic SPDX tagging
   - Usage of of_clk_get_parent_count() in more places
   - Proper implementation of the CDEV1/2 clocks on Tegra20
   - Allwinner H6 PRCM clock support and R40 EMAC support
   - Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
   - Round closest support for meson's mpll driver
   - Support for meson8b nand clocks and gxbb video decoder clocks
   - Mediatek mali clks
   - STM32MP1 fixes
   - Uniphier LD11/LD20 stream demux system clock"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
  clk: qcom: Export clk_fabia_pll_configure()
  clk: bcm: Update and add Stingray clock entries
  dt-bindings: clk: Update Stingray binding doc
  clk-si544: Properly round requested frequency to nearest match
  clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
  clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
  clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
  clk: ingenic: jz4770: Change OTG from custom to standard gated clock
  clk: ingenic: Support specifying "wait for clock stable" delay
  clk: ingenic: Add support for clocks whose gate bit is inverted
  clk: use match_string() helper
  clk: bcm2835: use match_string() helper
  clk: Return void from debug_init op
  clk: remove clk_debugfs_add_file()
  clk: tegra: no need to check return value of debugfs_create functions
  clk: davinci: no need to check return value of debugfs_create functions
  clk: bcm2835: no need to check return value of debugfs_create functions
  clk: no need to check return value of debugfs_create functions
  clk: imx6: add EPIT clock support
  clk: mvebu: use correct bit for 98DX3236 NAND
  ...

Pull MD updates from Shaohua Li:
 "A few fixes of MD for this merge window. Mostly bug fixes:

   - raid5 stripe batch fix from Amy

   - Read error handling for raid1 FailFast device from Gioh

   - raid10 recovery NULL pointer dereference fix from Guoqing

   - Support write hint for raid5 stripe cache from Mariusz

   - Fixes for device hot add/remove from Neil and Yufen

   - Improve flush bio scalability from Xiao"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  MD: fix lock contention for flush bios
  md/raid5: Assigning NULL to sh->batch_head before testing bit R5_Overlap of a stripe
  md/raid1: add error handling of read error from FailFast device
  md: fix NULL dereference of mddev->pers in remove_and_add_spares()
  raid5: copy write hint from origin bio to stripe
  md: fix two problems with setting the "re-add" device state.
  raid10: check bio in r10buf_pool_free to void NULL pointer dereference
  md: fix an error code format and remove unsed bio_sector

Pull sparc updates from David Miller:

 - a FPE signal fix that was also merged upstream

 - privileged ADI driver from Tom Hromatka

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: fix compat siginfo ABI regression
  selftests: sparc64: char: Selftest for privileged ADI driver
  char: sparc64: Add privileged ADI driver

Pull IDE updates from David Miller:
 "Primarily IRQ disabling avoidance changes from Sebastian Andrzej
  Siewior"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  ide: don't enable/disable interrupts in force threaded-IRQ mode
  ide: don't disable interrupts during kmap_atomic()
  ide: Handle irq disabling consistently
  alim15x3: move irq-restore before pci_dev_put()

Pull staging/IIO updates from Greg KH:
 "Here is the big staging and IIO driver update for 4.18-rc1.

  It was delayed as I wanted to make sure the final driver deletions did
  not cause any major merge issues, and all now looks good.

  There are a lot of patches here, just over 1000. The diffstat summary
  shows the major changes here:

	1007 files changed, 16828 insertions(+), 227770 deletions(-)

  Because of this, we might be close to shrinking the overall kernel
  source code size for two releases in a row.

  There was loads of work in this release cycle, primarily:

   - tons of ks7010 driver cleanups

   - lots of mt7621 driver fixes and cleanups

   - most driver cleanups

   - wilc1000 fixes and cleanups

   - lots and lots of IIO driver cleanups and new additions

   - debugfs cleanups for all staging drivers

   - lots of other staging driver cleanups and fixes, the shortlog has
     the full details.

  but the big user-visable things here are the removal of 3 chunks of
  code:

   - ncpfs and ipx were removed on schedule, no one has cared about this
     code since it moved to staging last year, and if it needs to come
     back, it can be reverted.

   - lustre file system is removed.

     I've ranted at the lustre developers about once a year for the past
     5 years, with no real forward progress at all to clean things up
     and get the code into the "real" part of the kernel.

     Given that the lustre developers continue to work on an external
     tree and try to port those changes to the in-kernel tree every once
     in a while, this whole thing really really is not working out at
     all. So I'm deleting it so that the developers can spend the time
     working in their out-of-tree location and get things cleaned up
     properly to get merged into the tree correctly at a later date.

  Because of these file removals, you will have merge issues on some of
  these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the
  atomisp driver). Just delete those files, it's a simple merge :)

  All of this has been in linux-next for a while with no reported
  problems"

* tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1011 commits)
  staging: ipx: delete it from the tree
  ncpfs: remove uapi .h files
  ncpfs: remove Documentation
  ncpfs: remove compat functionality
  staging: ncpfs: delete it
  staging: lustre: delete the filesystem from the tree.
  staging: vc04_services: no need to save the log debufs dentries
  staging: vc04_services: vchiq_debugfs_log_entry can be a void *
  staging: vc04_services: remove struct vchiq_debugfs_info
  staging: vc04_services: move client dbg directory into static variable
  staging: vc04_services: remove odd vchiq_debugfs_top() wrapper
  staging: vc04_services: no need to check debugfs return values
  staging: mt7621-gpio: reorder includes alphabetically
  staging: mt7621-gpio: change gc_map to don't use pointers
  staging: mt7621-gpio: use GPIOF_DIR_OUT and GPIOF_DIR_IN macros instead of custom values
  staging: mt7621-gpio: change 'to_mediatek_gpio' to make just a one line return
  staging: mt7621-gpio: dt-bindings: update documentation for #interrupt-cells property
  staging: mt7621-gpio: update #interrupt-cells for the gpio node
  staging: mt7621-gpio: dt-bindings: complete documentation for the gpio
  staging: mt7621-dts: add missing properties to gpio node
  ...

Pull libnvdimm updates from Dan Williams:
 "This adds a user for the new 'bytes-remaining' updates to
  memcpy_mcsafe() that you already received through Ingo via the
  x86-dax- for-linus pull.

  Not included here, but still targeting this cycle, is support for
  handling memory media errors (poison) consumed via userspace dax
  mappings.

  Summary:

   - DAX broke a fundamental assumption of truncate of file mapped
     pages. The truncate path assumed that it is safe to disconnect a
     pinned page from a file and let the filesystem reclaim the physical
     block. With DAX the page is equivalent to the filesystem block.
     Introduce dax_layout_busy_page() to enable filesystems to wait for
     pinned DAX pages to be released. Without this wait a filesystem
     could allocate blocks under active device-DMA to a new file.

   - DAX arranges for the block layer to be bypassed and uses
     dax_direct_access() + copy_to_iter() to satisfy read(2) calls.
     However, the memcpy_mcsafe() facility is available through the pmem
     block driver. In order to safely handle media errors, via the DAX
     block-layer bypass, introduce copy_to_iter_mcsafe().

   - Fix cache management policy relative to the ACPI NFIT Platform
     Capabilities Structure to properly elide cache flushes when they
     are not necessary. The table indicates whether CPU caches are
     power-fail protected. Clarify that a deep flush is always performed
     on REQ_{FUA,PREFLUSH} requests"

* tag 'libnvdimm-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
  dax: Use dax_write_cache* helpers
  libnvdimm, pmem: Do not flush power-fail protected CPU caches
  libnvdimm, pmem: Unconditionally deep flush on *sync
  libnvdimm, pmem: Complete REQ_FLUSH => REQ_PREFLUSH
  acpi, nfit: Remove ecc_unit_size
  dax: dax_insert_mapping_entry always succeeds
  libnvdimm, e820: Register all pmem resources
  libnvdimm: Debug probe times
  linvdimm, pmem: Preserve read-only setting for pmem devices
  x86, nfit_test: Add unit test for memcpy_mcsafe()
  pmem: Switch to copy_to_iter_mcsafe()
  dax: Report bytes remaining in dax_iomap_actor()
  dax: Introduce a ->copy_to_iter dax operation
  uio, lib: Fix CONFIG_ARCH_HAS_UACCESS_MCSAFE compilation
  xfs, dax: introduce xfs_break_dax_layouts()
  xfs: prepare xfs_break_layouts() for another layout type
  xfs: prepare xfs_break_layouts() to be called with XFS_MMAPLOCK_EXCL
  mm, fs, dax: handle layout changes to pinned dax mappings
  mm: fix __gup_device_huge vs unmap
  mm: introduce MEMORY_DEVICE_FS_DAX and CONFIG_DEV_PAGEMAP_OPS
  ...

Pull block fixes from Jens Axboe:
 "A few fixes for this merge window, where some of them should go in
  sooner rather than later, hence a new pull this week. This pull
  request contains:

   - Set of NVMe fixes, mostly follow up cleanups/fixes to the queue
     changes, but also teardown/removal and misc changes (Christop/Dan/
     Johannes/Sagi/Steve).

   - Two lightnvm fixes for issues that showed up in this window
     (Colin/Wei).

   - Failfast/driver flags inheritance for flush requests (Hannes).

   - The md device put sanitization and fix (Kent).

   - dm bio_set inheritance fix (me).

   - nbd discard granularity fix (Josef).

   - nbd consistency in command printing (Kevin).

   - Loop recursion validation fix (Ted).

   - Partition overlap check (Wang)"

[ .. and now my build is warning-free again thanks to the md fix  - Linus ]

* tag 'for-linus-20180608' of git://git.kernel.dk/linux-block: (22 commits)
  nvme: cleanup double shift issue
  nvme-pci: make CMB SQ mod-param read-only
  nvme-pci: unquiesce dead controller queues
  nvme-pci: remove HMB teardown on reset
  nvme-pci: queue creation fixes
  nvme-pci: remove unnecessary completion doorbell check
  nvme-pci: remove unnecessary nested locking
  nvmet: filter newlines from user input
  nvme-rdma: correctly check for target keyed sgl support
  nvme: don't hold nvmf_transports_rwsem for more than transport lookups
  nvmet: return all zeroed buffer when we can't find an active namespace
  md: Unify mddev destruction paths
  dm: use bioset_init_from_src() to copy bio_set
  block: add bioset_init_from_src() helper
  block: always set partition number to '0' in blk_partition_remap()
  block: pass failfast and driver-specific flags to flush requests
  nbd: set discard_alignment to the granularity
  nbd: Consistently use request pointer in debug messages.
  block: add verifier for cmdline partition
  lightnvm: pblk: fix resource leak of invalid_bitmap
  ...

Pull regulator updates from Mark Brown:
 "Quite a lot of core work this time around, though not 100% successful.

  We gained support for runtime mode changes thanks to David Collins and
  improved support for write only regulators (ones where we can't read
  back the configuration) from Douglas Anderson.

  There's been quite a bit of work from Linus Walleij on converting from
  specfying GPIOs by numbers to descriptors. Sadly the testing turned
  out to be less good than we had hoped and so a lot of this had to be
  reverted.

  We also have the start of updates to use coupled regulators from
  Maciej Purski, unfortunately there are further problems there so the
  last couple of patches have been reverted.

  We also have new drivers for BD71837 and SY8106A devices, SAW
  regulators on Qualcomm SPMI and dropped support for some preproduction
  chips that never made it to market from the AB8500 driver"

* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
  regulator: gpio: Revert
  ARM: pxa, regulator: fix building ezx e680
  regulator: Revert coupled regulator support again
  regulator: wm8994: Fix shared GPIOs
  regulator: max77686: Fix shared GPIOs
  regulator: bd71837: BD71837 PMIC regulator driver
  regulator: bd71837: Devicetree bindings for BD71837 regulators
  regulator: gpio: Get enable GPIO using GPIO descriptor
  regulator: fixed: Convert to use GPIO descriptor only
  regulator: s2mps11: Fix boot on Odroid XU3
  dt-bindings: qcom_spmi: Document SAW support
  regulator: qcom_spmi: Add support for SAW
  regulator: tps65090: Pass descriptor instead of GPIO number
  regulator: s5m8767: Pass descriptor instead of GPIO number
  regulator: pfuze100: Delete reference to ena_gpio
  regulator: max8952: Pass descriptor instead of GPIO number
  regulator: lp8788-ldo: Pass descriptor instead of GPIO number
  regulator: lm363x: Pass descriptor instead of GPIO number
  regulator: max8973: Pass descriptor instead of GPIO number
  regulator: mc13xxx-core: Switch to SPDX identifier
  ...

The problem here is that set_bit() and test_bit() take a bit number so
we should be passing 0 but instead we're passing (1 << 0) which leads to
a double shift.  It doesn't cause a runtime bug in the current code
because it's done consistently and we only set that one bit.

I decided to just re-use NVME_AER_NOTICE_NS_CHANGED instead of
introducing a new define for this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

A controller reset after a run time change of the CMB module parameter
breaks the driver. An 'on -> off' will have the driver use NULL for the
host memory queue, and 'off -> on' will use mismatched queue depth between
the device and the host.

We could fix both, but there isn't really a good reason to change this
at run time anyway, compared to at module load time, so this patch makes
parameter read-only after after modprobe.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch ensures the nvme namsepace request queues are not quiesced
on a surprise removal. It's possible the queues were previously killed
in a failed reset, so the queues need to be unquiesced to ensure all
requests are flushed to completion.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The controller is required to disable its host memory buffer use on
controller reset. We don't need to submit an admin command to delete it,
so this patch skips sending that command so we don't need to worry about
handling a timeout.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We've been ignoring NVMe error status on queue creations. Fortunately they
are uncommon, but we should handle these anyway. This patch adds checks
for the a positive error return value that indicates an NVMe status.

If we do see a negative return, the controller isn't usable, so this
patch returns immediately in since we can't unwind that failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The nvme pci driver never unmaps the doorbell registers while the requests
are active, so we can always safely update the completion queue head.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The nvme pci driver no longer handles completions under the cq lock,
so the nested locking is not necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>