- 08 Nov, 2016 40 commits
-
-
James Smart authored
Synchronize link speed with boot driver Link speed settings set by the boot driver are reported by the hw. Driver will attempt to read them, and if set, will respect their values. The driver can override the settings with its own if instructed by user space (via bsg), with the new values being picked up by the boot driver. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
James Smart authored
Correct panics with eh_timeout and eh_deadline We were having double completions on our SLI-3 version of adapters. Solved by clearing our command pointer before calling scsi_done. The eh paths potentially ran simulatenously and would see the non-null value and invoke scsi_done again. Signed-off-by:
-
James Smart authored
Fix lost target in pt-to-pt connect Change reject code to something that allows a retry Signed-off-by:
-
James Smart authored
Revise strings with full lpfc parameter name Signed-off-by:
-
James Smart authored
Code cleanup for lpfc_sriov_nr_virtfn parameter Signed-off-by:
-
James Smart authored
Code cleanup for lpfc_max_scsicmpl_time parameter Signed-off-by:
-
James Smart authored
Code cleanup for lpfc_topology parameter Signed-off-by:
-
James Smart authored
Code cleanup for lpfc_aer_support parameter Signed-off-by:
-
James Smart authored
Code cleanup for lpfc_enable_rrq parameter Signed-off-by:
-
James Smart authored
Code clean up for lpfc_iocb_cnt parameter Signed-off-by:
-
James Smart authored
Make lpfc_prot_mask and lpfc_prot_guard per hba parameters Signed-off-by:
-
James Smart authored
Set driver environment data on adapter Signed-off-by:
-
James Smart authored
Fix sg_reset on SCSI device causing kernel crash Driver could reference stale node pointers in task mgmt call. Changed to use resetting cmd and look up node pointer in task mgmt function. Signed-off-by:
-
James Smart authored
Correct embedded io wq element size. Embedded element sizes are 128 byte elements Signed-off-by:
-
Milan P. Gandhi authored
This patch does a cleanup and fixes few small typos in lpfc_scsi.c Signed-off-by:
Milan P. Gandhi <mgandhi@redhat.com> Signed-off-by:
James Smart <james.smart@avagotech.com> Reviewed-by:
-
Joao Pinto authored
I am going to leave Synopsys and so this patch changes the Maintainer for UFS Synopsys' specific drivers to my colleagues Manjunath and Prabu. Signed-off-by:
Joao Pinto <jpinto@synopsys.com> Signed-off-by:
-
Javier Martinez Canillas authored
It appears that the mailing list email address doesn't exist anymore: <iss_storagedev@hp.com>: host smtp.hp.com[15.73.96.116] said: 550 5.1.1 <iss_storagedev@hp.com>: Recipient address rejected: User unknown in virtual alias table (in reply to RCPT TO command) Signed-off-by:Javier Martinez Canillas <javier@osg.samsung.com> Acked-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
-
Javier Martinez Canillas authored
It's not necessary to cast the result of kmalloc, since void pointers are promoted to any other type. This also fixes following coccinelle warning: casting value returned by memory allocation function to (BIG_IOCTL_Command_struct *) is useless. Signed-off-by:
-
Christoph Hellwig authored
Having an I/O priority does not mean we should send all requests as HEAD OF QUEUE tags. Reported-by:
Adam Manzanares <adam.manzanares@wdc.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Hannes Reinicke <hare@suse.de> Signed-off-by:
-
Finn Thain authored
If a NCR5380 host instance ends up on a shared interrupt line then this printk will be a problem. It is already a problem on some Mac models: when testing mac_scsi on a PowerBook 180 I found that PDMA transfers (but not PIO transfers) cause the message to be logged. These spurious interrupts don't appear to come from the DRQ signal from the 5380. And they don't happen at all on the Mac LC III. A comment in the NetBSD source code mentions this mystery. Testing seems to show that we can safely ignore these interrupts. Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Reviewed-by:
Ondrej Zary <linux@rainbow-software.org> Tested-by:
Michael Schmitz <schmitzmic@gmail.com> Signed-off-by:
-
Finn Thain authored
Apply prototypes to get consistent function signatures for the DMA functions implemented in the board-specific drivers. To avoid using macros to alter actual parameters, some of those functions are reworked slightly. This is a step toward the goal of passing the board-specific routines to the core driver using an ops struct (as in a platform driver or library module). This also helps fix some inconsistent types: where the core driver uses ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of transfers, certain board-specific routines used unsigned long. While we are fixing these function signatures, pass the hostdata pointer to DMA routines instead of a Scsi_Host pointer, for shorter and faster code. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Finn Thain authored
Avoid the call to NCR5380_poll_politely2() when possible. The call is easily short-circuited on the PIO fast path, using the inline wrapper. This requires that the NCR5380_read macro be made available before any #include "NCR5380.h" so a few declarations have to be moved too. Signed-off-by:
-
Finn Thain authored
Pass a NCR5380_hostdata struct pointer to the board-specific routines instead of a Scsi_Host struct pointer. This reduces pointer chasing in the PIO and PDMA fast paths. The old way was a mistake because it is slow and the board-specific code is not concerned with the mid-layer. Signed-off-by:
-
Finn Thain authored
For timeout values adopt unsigned long, which is the type of jiffies etc. For chip register values and bit masks pass u8, which is the return type of readb, inb etc. For device register offsets adopt unsigned int, as it is suitable for adding to base addresses. Pass the NCR5380_hostdata pointer to the board-specific routines instead of the Scsi_Host pointer. The board-specific code is concerned with hardware and not with SCSI protocol or the mid-layer. Signed-off-by:
-
Finn Thain authored
The various 5380 drivers inconsistently store register pointers either in the Scsi_Host struct "legacy crap" area or in special, board-specific members of the NCR5380_hostdata struct. Uniform use of the latter struct makes for simpler and faster code (see the following patches) and helps to reduce use of the NCR5380_implementation_fields macro. Signed-off-by:
-
Finn Thain authored
Re-order struct members so that hot data lies at the beginning of the struct and cold data at the end. Improve the comments while we're here. Signed-off-by:
-
Finn Thain authored
If NCR5380_poll_politely() is called under irq lock, the polling time limit is clamped to avoid a spike in interrupt latency. When not under irq lock, the same polling time limit acts as the worst case delay between schedule() calls. During PDMA (under irq lock) I've found that the 10 ms time limit is sometimes too short, and leads to the error message, sd 0:0:0:0: [sda] tag#1 macscsi_pread: !REQ and !ACK This particular target identifies itself as a QUANTUM DAYTONA514S. It seems to be slower to assert ACK than the other targets I've tested. This patch solves the problem by increasing the polling timeout. Signed-off-by:
-
Finn Thain authored
When polling a device register under irq lock the polling loop terminates after a given number of jiffies. Make this timeout independent of the HZ setting. All 5380 drivers benefit from this patch, which optimizes the PIO fast path, because they all use PIO transfers (for phases other than DATA IN and DATA OUT). Some cards support only PIO transfers (even for DATA phases). CPU cycles are scarce on some of these systems, so a small improvement here makes a big difference. Signed-off-by:
-
Finn Thain authored
This patch fixes an old bug: accesses to device registers from the interrupt handler (after reselection, DMA completion etc.) could mess up a device register access elsewhere, if the latter takes place outside of an irq lock (during selection etc.). Signed-off-by:
-
Finn Thain authored
Signed-off-by:
-
Ondrej Zary authored
Merge the port-mapped IO and memory-mapped IO support (with the help of ioport_map) into the g_NCR5380 module and delete g_NCR5380_mmio. Signed-off-by:
-
Subhash Jadavani authored
Vendor specific setup_clocks callback may require the clocks managed by ufshcd driver to be ON. So if the vendor specific setup_clocks callback is called while the required clocks are turned off, it could result into unclocked register access. To prevent possible unclock register access, this change adds one more argument to setup_clocks callback to let it know whether it is called pre/post the clock changes by core driver. Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> Reviewed-by:
Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by:
-
Chad Dupuis authored
If we haven't logged into the fabric yet we want to be a little more nuanced with our CVL handling than what we've been: - If the FCF has been selected, check the source MAC to make sure the frame is from the FCF we've selected. - If a FCF is selected and the CVL is from the FCF but we have not logged in yet, then reset everything and go back to solicitation. Signed-off-by:
Chad Dupuis <chad.dupuis@cavium.com> Reviewed-by:
Johannes Thumshirn <jth@kernel.org> Signed-off-by:
-
Hannes Reinecke authored
When we receive an FLOGI but have already sent our own we should not advance the state machine but rather wait for our FLOGI to return before continuing with PLOGI. Signed-off-by:
-
Hannes Reinecke authored
When the port is already started we don't need to login; that will only confuse the state machine. Signed-off-by:
-
Hannes Reinecke authored
When fc_rport_login() is called while the rport is not in RPORT_ST_INIT, RPORT_ST_READY, or RPORT_ST_DELETE login is already in progress and there's no need to drop down to FLOGI; doing so will only confuse the other side. Signed-off-by:
-
Chad Dupuis authored
When an ELS response handler receives a -FC_EX_CLOSED, the rdata->rp_mutex is already held which can lead to a deadlock condition like the following stack trace: [<ffffffffa04d8f18>] fc_rport_plogi_resp+0x28/0x200 [libfc] [<ffffffffa04cfa1a>] fc_invoke_resp+0x6a/0xe0 [libfc] [<ffffffffa04d0c08>] fc_exch_mgr_reset+0x1b8/0x280 [libfc] [<ffffffffa04d87b3>] fc_rport_logoff+0x43/0xd0 [libfc] [<ffffffffa04ce73d>] fc_disc_stop+0x6d/0xf0 [libfc] [<ffffffffa04ce7ce>] fc_disc_stop_final+0xe/0x20 [libfc] [<ffffffffa04d55f7>] fc_fabric_logoff+0x17/0x70 [libfc] The other ELS handlers need to follow the FLOGI response handler and simply do a kref_put against the fc_rport_priv struct and exit when receving a -FC_EX_CLOSED response. Signed-off-by:
-
Hannes Reinecke authored
The list of attached 'rdata' remote port structures is RCU protected, so there is no need to take the 'disc_mutex' when traversing it. Rather we should be using rcu_read_lock() and kref_get_unless_zero() to validate the entries. We need, however, take the disc_mutex when deleting an entry; otherwise we risk clashes with list_add. Signed-off-by:
-
Hannes Reinecke authored
The kref handling in fc_rport is a mess. This patch updates the kref handling according to the following rules: - Take a reference whenever scheduling a workqueue - Take a reference whenever an ELS command is send - Drop the reference at the end of the workqueue function - Drop the reference at the end of handling ELS replies - Take a reference when allocating an rport - Drop the reference when removing an rport Signed-off-by:
-
John Garry authored
The hip06 D03 and hip07 D05 boards have different reference clock frequencies for the SAS controller. Register PHY_CTRL needs to be programmed differently according to this frequency, so add support for this. The default register setting in PHY_CTRL is for 50MHz, so only update this register when the refclk frequency is 66MHz. For ACPI we expect the _RST handler to set the correct value for PHY_CTRL (we're forced to take different approach for DT and ACPI as ACPI does not support fixed-clock device). Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
-
