Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Eagle board dependent part of the I2C0 device node.

The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A77970 parts of the I2C[0-4] device node.

Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Populate the ethernet@e6800000 device node to enable Ethernet interface
for R-Car M3-N (R8A77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.

Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.

Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.

Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.

Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.

Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.

Most features are enabled through the shared salvator-xs.dtsi board
description.  The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Move "usb2_ph1" place-holder device node next to "usb2_phy0" one.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.

This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "#pwm-cells" property to "pwm@e6e31000" device node.

This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "#phy-cells" property to "usb-phy@e65ee000" device node.

This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.

This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.

This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.

This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPIO nodes to r8a77965 SoC device tree file.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SCIF[0-5] device nodes for M3-N (r8a77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add dmac[0-2] device nodes for R-Car M3-N (r8a77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add basic support for R-Car Salvator-X M3-N (R8A77965) board.

Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Basic support for the Gen 3 R-Car M3-N SoC.

Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add configuration option for the R-Car M3-N (R8A77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe frequencies, other than the default for CA53 cores.  This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe frequencies, other than the default for CA53 cores.  This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Condor board dependent part of the EtherAVB device node.

Based  on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device  tree for  the R8A77980 SoC based Condor board.
The board has 1 debug serial port (SCIF0); include support for it, so
that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: correct memory size to 0x78000000 (2GiB)]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A77980 part of the EtherAVB device node.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe [H]SCIF ports in the R8A77980 device tree.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable the DU, providing only the VGA output for now.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>