- 18 Jun, 2013 4 commits
-
-
Daniel Vetter authored
Nowadays (i.e. with Valleyview) we also have edp on non-PCH_SPLIT platforms, so just checking for LVDS is not good enough. Secondly we have full pfit pipe config tracking, so we'll correctly disable the pfit as part of the initial modeset. For fastboot we need a bit of work here to correctly kill unsupported configs (if e.g. the pfit is used on anything else than the built-in panel). But since that's not yet supported we don't need to worry. Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Daniel Vetter authored
Again we don't really support different settings, so don't let the BIOS sneak stuff through. Since the motivation for this patch series is to ensure we have the correct gamma table mode selected also add the required write to the GAMMA_MODE register to select the 8bit legacy table. And since I find lowercase letters in #defines offensive, also bikeshed those. Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Daniel Vetter authored
Same reasons as for the previous patch, just no bug report about anything going wrong yet: We only support exactly the mode we program, so don't leave any stale BIOS state behind. Again this will be fun to properly track for fastboot. Reviewed-by:
-
Daniel Vetter authored
Dragging random garbage along from the BIOS isn't a good idea, since we really only support exactly what we've set up. In the specific case for the bug reporter the BIOS used the 10bit gamma table, but since we only support an 8bit table the dark colors ended up all wrong and the light ones all unadjusted. Note that this has a nice implication for fastboot, it essentially means that we have quite a bit more state to check and compare before we can decide whether fastboot is possible. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65593Reported-and-Tested-by:
Thomas Hebb <tommyhebb@gmail.com> Cc: stable@vger.kernel.org Reviewed-by:
-
- 13 Jun, 2013 7 commits
-
-
Mika Kuoppala authored
After hang check timer has declared gpu to be hung, rings are reset. In ring reset, when clearing request list, do post mortem analysis to find out the guilty batch buffer. Select requests for further analysis by inspecting the completed sequence number which has been updated into the HWS page. If request was completed, it can't be related to the hang. For noncompleted requests mark the batch as guilty if the ring was not waiting and the ring head was stuck inside the buffer object or in the flush region right after the batch. For everything else, mark them as innocents. v2: Fixed a typo in commit message (Ville Syrjälä) v3: - more descriptive function parameters (Chris Wilson) - use masked head address when inspecting if request is in ring - s/hangcheck.last_action/hangcheck.action - added comment about unmasked head hitting batch_obj range Reviewed-by:Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Mika Kuoppala authored
For guilty batchbuffer analysis later on when rings are reset, store what state the ring was on when hang was declared. This helps to weed out the waiting rings from the active ones. Signed-off-by:
-
Mika Kuoppala authored
In order to track down a batch buffer and context which caused the ring to hang, store reference to bo into the request struct. Request can also cause gpu to hang after the batch in the flush section in the ring. To detect this add start of the flush portion offset into the request. v2: Included comment about request vs batch_obj lifetimes (Chris Wilson) Signed-off-by:
-
Mika Kuoppala authored
Only execbuffer needed all the parameters on i915_add_request(). By putting __i915_add_request behind macro, all current callsites become cleaner. Following patch will introduce a new parameter for __i915_add_request. With this patch, only the relevant callsite will reflect the change making commit smaller and easier to understand. v2: _i915_add_request as function name (Chris Wilson) v3: change name __i915_add_request and fix ordering of params (Ben Widawsky) Signed-off-by:
-
Mika Kuoppala authored
To get context hang statistics for specified context, add i915_gem_context_get_hang_stats(). For arb-robustness, every context needs to have its own hang statistics tracking. Added function will return the user specified context statistics or in case of default context, statistics from drm_i915_file_private. v2: handle default context inside get_reset_state v3: return struct pointer instead of passing it in as param (Chris Wilson) Signed-off-by: -
Mika Kuoppala authored
To count context losses, add struct i915_ctx_hang_stats for both i915_hw_context and drm_i915_file_private. drm_i915_file_private is used when there is no context. v2: renamed and cleaned up the struct (Chris Wilson, Ian Romanick) Signed-off-by:
-
Ville Syrjälä authored
The specs are a bit unclear whether the per-plane trickle feed disable control exists on VLV. There is another trickle feed disable control in the MI_ARB register. After some experimentation it turns out both the DSPCNTR trickle feed bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't seem to have any effect. The MI_ARB bit, on the other hand, has a noticable effect. I performed an experiment where I reduced the FIFO size via DSPARB and observed the effect of the MI_ARB trickle feed bit on the display. Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems didn't start until DSPARB=0x09090909. This seems to confirm that the MI_ARB trickle feed bit actually does work. So replace the use of the DSPCNTR trickle feed bits with MI_ARB on VLV. v2: Amend commit message with results from experimentation Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
- 12 Jun, 2013 9 commits
-
-
Daniel Vetter authored
We have a nice comment saying that the pixel multiplier only sticks once the vco is on and stable. The only problem is that the enable bit wasn't set at all. This patch fixes this and so brings the ilk+ pch pll code in line with the i8xx/i9xx pll code. Or at least improves matters a lot. This should fix sdvo on ilk-ivb for low-res modes. Reviewed-by:
Damien Lespiau <damien.lespiau@intel.com> Signed-off-by:
-
Daniel Vetter authored
Just the plumbing, all the modeset and enable code has not yet been switched over to use the new state. It seems to be decently broken anyway, at least wrt to handling of the special pixel mutliplier enabling sequence. Follow-up patches will clean up that mess. Another missing piece is more careful handling (and fixup) of the fp1 alternate divisor state. The BIOS most likely doesn't bother to program that one to what we expect. So we need to be more careful with comparing that state, both for cross checking but also when checking for dpll sharing when acquiring shared dpll. Otherwise fastboot will deny a few shared dpll configurations which would otherwise work. v2: We need to memcpy the pipe config dpll hw state into the pll, for otherwise the cross-check code will get angry. v3: Don't forget to read the pch pll state in the crtc get_pipe_config function for ibx/ilk platforms. Reviewed-by:
-
Daniel Vetter authored
Now that we have proper hw state reconstruction we should never have a case where we don't have the software dpll state properly set up. So add WARNs to the respective !pll cases in enable/disabel_shared_dpll. Reviewed-by:
-
Daniel Vetter authored
Simply grew too large and needed to be split up into parts. Reviewed-by:
-
Daniel Vetter authored
Simply grew too big. This also makes the fixup and restore logic in setup_hw_state stand out a bit more clearly. Reviewed-by:
-
Daniel Vetter authored
Currently still with an empty register state, this will follow in a next step. This one here just creates the new vfunc and uses it for cross-checking, initial state takeover and the dpll assert function. And add a FIXME for the ddi pll readout code, which still needs to be converted over. v2: - Add some hw state readout debug output. - Also cross check the enabled crtc counting. Note that I've botched up the patch ordering, and before this patch we've read out the pll selection correctly, but did not reconstruct the refcounts properly. See the bug link. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65673Reviewed-by:
-
Daniel Vetter authored
So don't try to store it in the DPLL_FP register. Otherwise it looks like the limits for pineview are correct: It has it's own clock computation code, which doesn't use an offset for n divisors, and the register value based m limits look sane enough. v2: Rebase on top of the pineview clock refactor and fixup up the commit message: It's m1 pnv doens't care about, not m2! Quoting Damien's review: - "n can vary between 2 and 6, but we declare the 3-6 as limits. - "p1 seems to be able to go up to 9 - "the m upper limit seems a bit big, but the docs are a bit shy on that values for pnv. "Otherwise, the change itself seems good:" Reviewed-by: -
Daniel Vetter authored
We don't (yet) have proper pixel multiplier readout support on pch split platforms, so the cross check will naturally fail. v2: Fix spelling in the comment, spotted by Ville. v3: Since the ordering constraint is pretty tricky between the crtc get_pipe_config callback and the encoder->get_config callback add a few comments about it. Prompted by a discussion with Chris Wilson on irc about why this does work anywhere else than on i915g/gm. Reported-by:
-
Chris Wilson authored
Stéphane Marchesin found a bug where the fences were not being restored, and in particular the fence pin_count was incorrect. Had we had a warning in place, this bug would have come to light much earlier. Better late than never? Signed-off-by:
-
- 11 Jun, 2013 4 commits
-
-
Chris Wilson authored
This is of no value to the developer reading the report, let alone the bamboozled user. Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by:
-
Chris Wilson authored
If we detect a ring is in a valid wait for another, just let it be. Eventually it will either begin to progress again, or the entire system will come grinding to a halt and then hangcheck will fire as soon as the deadlock is detected. This error was foretold by Ben in commit 05407ff8 Author: Mika Kuoppala <mika.kuoppala@linux.intel.com> Date: Thu May 30 09:04:29 2013 +0300 drm/i915: detect hang using per ring hangcheck_score "If ring B is waiting on ring A via semaphore, and ring A is making progress, albeit slowly - the hangcheck will fire. The check will determine that A is moving, however ring B will appear hung because the ACTHD doesn't move. I honestly can't say if that's actually a realistic problem to hit it probably implies the timeout value is too low." v2: Make sure we don't even incur the KICK cost whilst waiting. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65394Signed-off-by:
-
Chris Wilson authored
After kicking a ring, it should be free to make progress again and so should not be accused of being stuck until hangcheck fires once more. In order to catch a denial-of-service within a batch or across multiple batches, we still do increment the hangcheck score - just not as severely so that it takes multiple kicks to fail. This should address part of Ben's justified criticism of commit 05407ff8 Author: Mika Kuoppala <mika.kuoppala@linux.intel.com> Date: Thu May 30 09:04:29 2013 +0300 drm/i915: detect hang using per ring hangcheck_score "There's also another corner case on the kick. If the seqno = 2 (though not stuck), and on the 3rd hangcheck, the ring is stuck, and we try to kick it... we don't actually try to find out if the kick helped." v2: Make sure we catch DoS attempts with batches full of invalid WAITs. v3: Preserve the ability to detect loops by always charging the ring if it is busy on the same request. v4: Make sure we queue another check if on a new batch References: https://bugs.freedesktop.org/show_bug.cgi?id=65394Signed-off-by:
-
Chris Wilson authored
When we reset and restart a ring, we also want to clear any existing hangcheck. Signed-off-by:
-
- 10 Jun, 2013 16 commits
-
-
Damien Lespiau authored
In case of intel_sdvo_get_active_outputs() failing, we end up reading a value from the stack. Signed-off-by:
-
Damien Lespiau authored
It's now intel_sdvo_get_capabilities(). Signed-off-by:
-
Daniel Vetter authored
The hw state readout code for the pipe config will now check this for us, so rip out this hand-rolled complexity. Reviewed-by:
-
Daniel Vetter authored
Looks at first like a bit of overkill, but - Haswell actually wants different enable/disable functions for different plls. - And once we have full dpll hw state tracking we can move the full register setup into the ->enable hook. Reviewed-by:
-
Daniel Vetter authored
Using ids in register macros is much more common in our driver. Also this way we can reduce the platform specific stuff a bit. Reviewed-by:
-
Daniel Vetter authored
An id to match the idx (useful for register access macros) and a name fore neater debug output. Reviewed-by:
-
Daniel Vetter authored
In the future this won't be just for pch plls, so move it into the shared dpll init code. v2: Bikeshed the uncessary {} away while applying to appease checkpatch. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1) Signed-off-by: -
Daniel Vetter authored
Well, the first step of a long road at least, it only reads out the pipe -> shared dpll association thus far. Other state which needs to follow: - hw state of the dpll (on/off + dpll registers). Currently we just read that out from the hw state, but that doesn't work too well when the dpll is in use, but not yet fully enabled. We get away since most likely it already has been enabled and so the correct state is left behind in the registers. But that doesn't hold for atomic modesets when we want to enable all pipes at once. - Refcount reconstruction for each dpll. - Cross-checking of all the above. For that we need to keep the dpll register state both in the pipe and in the shared_dpll struct, so that we can check that every pipe is still connected to a correctly configured dpll. Note that since the refcount resconstruction isn't done yet this will spill a few WARNs at boot-up while trying to disable pch plls which have bogus refcounts. But since there's still a pile of refactoring to do I'd like to lock down the state handling as soon as possible hence decided against reordering the patches to quiet these WARNs - after all the issues they're complaining about have existed since forever, as Jesse can testify by having pch pll states blow up consistently in his fastboot patches ... v2: We need to preserve the old shared_dpll since currently the shared dpll refcount dropping/getting is done in ->mode_set. With the usual pipe_config infrastructure the old dpll id is already lost at that point, hence preserve it in the new config. v3: Rebase on top of the ips patch from Paulo. v4: We need to unconditionally take over the shared_dpll id from the old pipe config when e.g. doing a direct pch port -> cpu edp transition. v5: Move the saving of the old shared_dpll id to an ealier patch. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
The bits are evenly space, so we can cut down on two big switch blocks. This also greatly simplifies the hw state readout which follows in the next patch. Reviewed-by:
-
Daniel Vetter authored
With the big sed-job prep work done this is now really simple. With the exception that we only assign the right shared dpll id in the ->mode_set callback but also depend upon the old one still being around. Until that mess is fixed up we need to jump through a few hoops to keep the old value save. v2: Kill the funny whitespace spotted by Chris. v3: Move the shared_dpll pipe config fixup into this patch as noticed by Ville. Also unconditionally set the shared_dpll with the current one, since otherwise we won't handle direct pch port -> cpu edp transitions correctly. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
Dealing with discrete enum values is simpler for hw state readout and pipe config computations than pointers - having neat names instead of chasing pointers should look better in the code. This isn't a that good reason for pch plls, but on haswell we actually have 3 different types of plls: WRPLL, SPLL and the DP clocks. Having explicit names should help there. Since this also adds the intel_crtc_to_shared_dpll helper to further abstract away the crtc -> dpll relationship this will also help to make the next patch simpler, which moves the shared dpll into the pipe configuration. Also note that for uniformity we have two special dpll ids: NONE for pipes which need a shared pll but don't have one (yet) and private for when there's a non-shared pll (e.g. per-pipe or per-port pll). I've thought whether we should also add a 2nd enum for the type of the pll we want (for really generic pll selection code) but thrown that idea out again - likely there's too much platform craziness going on to be able to share the pll selection logic much. Since this touched all the shared_pll functions a bit I've also done an s/intel_crtc/crtc/ replacement on a few of them. v2: Kill DPLL_ID_NONE. It's probably better to call it DPLL_ID_INVALID and use it to check that the compute config stage assigns a dpll to every pipe. But since that code isn't ready yet until we move the dpll selection out of the ->mode_set callback, there's no use for it. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
For fastboot we need some support to read out the sharing state of plls, at least for platforms where they can be shared (or freely assigned at least). Now for ivb we already have pretty extensive infrastructure for tracking pch plls, and it took us an aweful lot of tries to get that remotely right. Note that hsw could also share plls, but even now they're already freely assignable. So we need this on more than just ivb. So on top of the usual fastboot fun pll sharing seems to be an additional step up in fragility. Hence a common infrastructure for all shared/freely assignable display plls seems to be in order. The plan is to have a bit of dpll hw state readout code, which can be used individually, but also to fill in the pipe config. The hw state cross check code will then use that information to make sure that after every modeset every pipe still is connected to a pll which still has the correct configuration - a lot of the pch pll sharing bugs where due to incorrect sharing. We start this endeavour with a simple s/pch_pll/shared_dpll/ rename job. Reviewed-by:
-
Daniel Vetter authored
Before I start to make a complete mess out of this, crank up the paranoia level a bit. v2: Kill the has_pch_encoder check in put_shared_dpll - it's invalid as spotted by Ville since we currently only put the dpll when we already have the new pipe config. So a direct pch port -> cpu edp transition will hit this. v3: Now that I've lifted my blinders add the WARN_ON Ville requested. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
Simlar to how disable already works on haswell. This is possible since we now carefully track the pch state in the pipe config. Reviewed-by:
-
Daniel Vetter authored
We ->mode_set is called we can't just blindly reuse an existing pll since that might be shared with a different, still active pch output. v2: Only update the pll settings when the pch pll is know to be unused, otherwise we can wreak havoc with a running pipe. Which in the case of DP will likely result in a black screen due to loss of link lock. v3: Tighten up the asserts a bit more, especially make sure that the pch pll is still enabled when we try to disable it. This would have caught the bug fixed in this patch. Reviewed-by:
-
Damien Lespiau authored
This makes, arguably, the condition on state easier to read. Suggested-by:
-
