- 31 Mar, 2016 40 commits
-
-
Arnd Bergmann authored
commit ba4bc32e upstream. An older patch to convert the API in the s3c i2s driver ended up passing a const pointer into a function that takes a non-const pointer, so we now get a warning: sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe': sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] However, the s3c_i2sv2_register_component() function again passes the pointer into another function taking a const, so we just need to change its prototype. Fixes: eca3b01d ("ASoC: switch over to use snd_soc_register_component() on s3c i2s") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Huibin Hong authored
commit b920cc31 upstream. Rockchip_spi_set_cs could be called by spi_setup, but spi_setup may be called by device driver after runtime suspend. Then the spi clock is closed, rockchip_spi_set_cs may access the spi registers, which causes cpu block in some socs. Fixes: 64e36824 ("spi/rockchip: add driver for Rockchip RK3xxx") Signed-off-by:
Huibin Hong <huibin.hong@rock-chips.com> Signed-off-by:
-
Jesse Gross authored
commit b8cba75b upstream. ipip encapsulated packets can be merged together by GRO but the result does not have the proper GSO type set or even marked as being encapsulated at all. Later retransmission of these packets will likely fail if the device does not support ipip offloads. This is similar to the issue resolved in IPv6 sit in feec0cb3 ("ipv6: gro: support sit protocol"). Reported-by:
Patrick Boutilier <boutilpj@ednet.ns.ca> Fixes: 9667e9bb ("ipip: Add gro callbacks to ipip offload") Tested-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Jesse Gross <jesse@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David Hildenbrand authored
commit b15d53d0 upstream. kmap_coherent needs disabled preemption to not schedule in the critical section, just like kmap_coherent on mips and kmap_atomic in general. Fixes: 8222dbe2 "sched/preempt, mm/fault: Decouple preemption from the page fault logic" Reported-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Tested-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Rich Felker <dalias@libc.org> Signed-off-by:
-
Arnd Bergmann authored
commit aeb6641f upstream. gcc-6 complains about the indentation of the lpfc_destroy_vport_work_array() call in lpfc_online(), which clearly doesn't look right: drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_online': drivers/scsi/lpfc/lpfc_init.c:2880:3: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation] lpfc_destroy_vport_work_array(phba, vports); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/scsi/lpfc/lpfc_init.c:2863:2: note: ...this 'if' clause, but it is not if (vports != NULL) ^~ Looking at the patch that introduced this code, it's clear that the behavior is correct and the indentation is wrong. This fixes the indentation and adds curly braces around the previous if() block for clarity, as that is most likely what caused the code to be misindented in the first place. Signed-off-by:
Sebastian Herbszt <herbszt@gmx.de> Reviewed-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Paolo Abeni authored
commit ad0ea198 upstream. Currently, ingress ipv4 broadcast datagrams are dropped since, in udp_v4_early_demux(), ip_check_mc_rcu() is invoked even on bcast packets. This patch addresses the issue, invoking ip_check_mc_rcu() only for mcast packets. Fixes: 6e540309 ("ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
NeilBrown authored
commit a6ab1e81 upstream. sunrpc_cache_pipe_upcall() can detect a race if CACHE_PENDING is no longer set. In this case it aborts the queuing of the upcall. However it has already taken a new counted reference on "h" and doesn't "put" it, even though it frees the data structure holding the reference. So let's delay the "cache_get" until we know we need it. Fixes: f9e1aedc ("sunrpc/cache: remove races with queuing an upcall.") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit a25f4a95 upstream. drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used Apparently the conversion to alarm_irq_enable forgot to wire up the callback. Fixes: 16380c15 ("RTC: Convert rtc drivers to use the alarm_irq_enable method") Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Ard Biesheuvel authored
commit 9c6672ac upstream. Commit 6d80dba1 ("efi: Provide a non-blocking SetVariable() operation") implemented a non-blocking alternative for the UEFI SetVariable() invocation performed by efivars, since it may occur in atomic context. However, this version of the function was never exposed via the efivars struct, so the non-blocking versions was not actually callable. Fix that. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 6d80dba1 ("efi: Provide a non-blocking SetVariable() operation") Link: http://lkml.kernel.org/r/1454364428-494-2-git-send-email-matt@codeblueprint.co.ukSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Pali Rohár authored
commit 98f42221 upstream. Based on CPU type choose generic omap3 or omap3430 specific cpuidle parameters. Parameters for omap3430 were measured on Nokia N900 device and added by commit 5a1b1d3a ("OMAP3: RX-51: Pass cpu idle parameters") which were later removed by commit 231900af ("ARM: OMAP3: cpuidle - remove rx51 cpuidle parameters table") due to huge code complexity. This patch brings cpuidle parameters for omap3430 devices again, but uses simple condition based on CPU type. Fixes: 231900af ("ARM: OMAP3: cpuidle - remove rx51 cpuidle parameters table") Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Linus Walleij authored
commit 95a001f2 upstream. As of commit 876fe76d "mtd: maps: physmap: Add reference counter to set_vpp()" the comment in the header file is incorrect and misleading. Fix it up. Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Parsons <lost.distance@yahoo.com> Fixes: 876fe76d ("mtd: maps: physmap: Add reference counter to set_vpp()") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Dan Carpenter authored
commit 93fce954 upstream. At the end of the function we expect "status" to be zero, but it's either -EINVAL or uninitialized. Fixes: 788bf83d ('drm/amdkfd: Add wave control operation to debugger') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
commit 8e580411 upstream. The davinci platform has tried to get support for the EEPROM right, but failed to get a clean build so far. At the moment, we get a warning whenever CONFIG_SYSFS is disabled, as that is needed by EEPROM_AT24: warning: (MACH_DAVINCI_EVM && MACH_SFFSDR && MACH_DAVINCI_DM6467_EVM && MACH_DAVINCI_DM365_EVM && MACH_DAVINCI_DA830_EVM && MACH_MITYOMAPL138 && MACH_MINI2440) selects EEPROM_AT24 which has unmet direct dependencies (I2C && SYSFS) Kevin Hilman initially added the 'select' to ensure that EEPROM_AT24 is always enabled in machines that really want it for normal operation (i.e. for reading the MAC address). This broke when I2C was disabled, and Russell King followed up with another patch to select that as well. I now see that the SYSFS dependency is still missing, which leaves us with three options: a) add 'select SYSFS' in addition to the others b) change AT24_EEPPROM to work without sysfs (should be possible) c) remove all those selects again and get the files to build when I2C is disabled. I would really hate to do a) because adding select statements that hardwire user-selectable symbols is generally a bad idea. I first tried b) but then ended up redoing the patch from scratch to approach c), so we can also remove the other selects. I checked that CONFIG_I2C is still enabled with davinci_all_defconfig, so that does not have to change. Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Dan Carpenter authored
commit 8c09b9fd upstream. We call spin_lock_irqrestore with "flags" set to zero instead of to the value from spin_lock_irqsave(). Fixes: aaaf5fbf ('rtc: add driver for DS1685 family of real time clocks') Signed-off-by:
-
Marcin Ślusarz authored
commit 89fee59b upstream. Steam frequently puts game binaries in folders with spaces. Note: "(deleted)" markers are now treated as part of the file name. Signed-off-by:
Marcin Ślusarz <marcin.slusarz@gmail.com> Acked-by:
Namhyung Kim <namhyung@kernel.org> Fixes: 60648033 ("perf tools: Use sscanf for parsing /proc/pid/maps") Link: http://lkml.kernel.org/r/20160119190303.GA17579@marcin-Inspiron-7720Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Arnd Bergmann authored
commit 83d6f1f1 upstream. Code that was added back in 2.6.38 has an obvious overflow when accessing a static array, and at the time it was added only a code comment was put in front of it as a reminder to have it reviewed properly. This has not happened, but gcc-6 now points to the specific overflow: drivers/net/wireless/ath/ath9k/eeprom.c: In function 'ath9k_hw_get_gain_boundaries_pdadcs': drivers/net/wireless/ath/ath9k/eeprom.c:483:44: error: array subscript is above array bounds [-Werror=array-bounds] maxPwrT4[i] = data_9287[idxL].pwrPdg[i][4]; ~~~~~~~~~~~~~~~~~~~~~~~~~^~~ It turns out that the correct array length exists in the local 'intercepts' variable of this function, so we can just use that instead of hardcoding '4', so this patch changes all three instances to use that variable. The other two instances were already correct, but it's more consistent this way. Signed-off-by:
-
Dan Carpenter authored
commit 8134233e upstream. If the call to acpi_get_object_info() fails then "info" hasn't been initialized. In that situation, we already know that "version" should be XGENE_AHCI_V1 so we don't actually need to dereference "info". Fixes: c9802a4b ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.') Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Addy Ke authored
commit 80abf888 upstream. Generic dma controller on Rockchips' platform cannot support DMAFLUSHP instruction which make dma to flush the req of non-aligned or non-multiple of what we need. That will cause an unrecoverable dma bus error. The saftest way is to set dma max burst to 1. Signed-off-by:
Addy ke <addy.ke@rock-chips.com> Fixes: 64e36824 ("spi/rockchip: add driver for Rockchip...") Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> cc: Heiko Stuebner <heiko@sntech.de> cc: Olof Johansson <olof@lixom.net> cc: Doug Anderson <dianders@chromium.org> cc: Sonny Rao <sonnyrao@chromium.org> Acked-by:
Caesar Wang <wxt@rock-chips.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Ville Syrjälä authored
commit 7d3fdfff upstream. Restore the lost phys status page cleanup. Fixes the following splat with DMA_API_DEBUG=y: WARNING: CPU: 0 PID: 21615 at ../lib/dma-debug.c:974 dma_debug_device_change+0x190/0x1f0() pci 0000:00:02.0: DMA-API: device driver has pending DMA allocations while released from device [count=1] One of leaked entries details: [device address=0x0000000023163000] [size=4096 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent] Modules linked in: i915(-) i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm sha256_generic hmac drbg ctr ccm sch_fq_codel binfmt_misc joydev mousedev arc4 ath5k iTCO_wdt mac80211 smsc_ircc2 ath snd_intel8x0m snd_intel8x0 snd_ac97_codec ac97_bus psmouse snd_pcm input_leds i2c_i801 pcspkr snd_timer cfg80211 snd soundcore i2c_core ehci_pci firewire_ohci ehci_hcd firewire_core lpc_ich 8139too rfkill crc_itu_t mfd_core mii usbcore rng_core intel_agp intel_gtt usb_common agpgart irda crc_ccitt fujitsu_laptop led_class parport_pc video parport evdev backlight CPU: 0 PID: 21615 Comm: rmmod Tainted: G U 4.4.0-rc4-mgm-ovl+ #4 Hardware name: FUJITSU SIEMENS LIFEBOOK S6120/FJNB16C, BIOS Version 1.26 05/10/2004 e31a3de0 e31a3de0 e31a3d9c c128d4bd e31a3dd0 c1045a0c c15e00c4 e31a3dfc 0000546f c15dfad2 000003ce c12b3740 000003ce c12b3740 00000000 00000001 f61fb8a0 e31a3de8 c1045a83 00000009 e31a3de0 c15e00c4 e31a3dfc e31a3e4c Call Trace: [<c128d4bd>] dump_stack+0x16/0x19 [<c1045a0c>] warn_slowpath_common+0x8c/0xd0 [<c12b3740>] ? dma_debug_device_change+0x190/0x1f0 [<c12b3740>] ? dma_debug_device_change+0x190/0x1f0 [<c1045a83>] warn_slowpath_fmt+0x33/0x40 [<c12b3740>] dma_debug_device_change+0x190/0x1f0 [<c1065499>] notifier_call_chain+0x59/0x70 [<c10655af>] __blocking_notifier_call_chain+0x3f/0x80 [<c106560f>] blocking_notifier_call_chain+0x1f/0x30 [<c134cfb3>] __device_release_driver+0xc3/0xf0 [<c134d0d7>] driver_detach+0x97/0xa0 [<c134c440>] bus_remove_driver+0x40/0x90 [<c134db18>] driver_unregister+0x28/0x60 [<c1079e8c>] ? trace_hardirqs_on_caller+0x12c/0x1d0 [<c12c0618>] pci_unregister_driver+0x18/0x80 [<f83e96e7>] drm_pci_exit+0x87/0xb0 [drm] [<f8b3be2d>] i915_exit+0x1b/0x1ee [i915] [<c10b999c>] SyS_delete_module+0x14c/0x210 [<c1079e8c>] ? trace_hardirqs_on_caller+0x12c/0x1d0 [<c115a9bd>] ? ____fput+0xd/0x10 [<c1002014>] do_fast_syscall_32+0xa4/0x450 [<c149f6fa>] sysenter_past_esp+0x3b/0x5d ---[ end trace c2ecbc77760f10a0 ]--- Mapped at: [<c12b3183>] debug_dma_alloc_coherent+0x33/0x90 [<f83e989c>] drm_pci_alloc+0x18c/0x1e0 [drm] [<f8acd59f>] intel_init_ring_buffer+0x2af/0x490 [i915] [<f8acd8b0>] intel_init_render_ring_buffer+0x130/0x750 [i915] [<f8aaea4e>] i915_gem_init_rings+0x1e/0x110 [i915] v2: s/BUG_ON/WARN_ON/ since dim doens't like the former anymore Cc: Chris Wilson <chris@chris-wilson.co.uk> Fixes: 5c6c6003 ("drm/i915: Remove DRI1 ring accessors and API") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1) Link: http://patchwork.freedesktop.org/patch/msgid/1452538112-5331-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Marco Angaroni authored
commit 7617a24f upstream. The IPVS SIP persistence engine is not able to parse the SIP header "Call-ID" when such header is inserted in the first positions of the SIP message. When IPVS is configured with "--pe sip" option, like for example: ipvsadm -A -u 1.2.3.4:5060 -s rr --pe sip -p 120 -o some particular messages (see below for details) do not create entries in the connection template table, which can be listed with: ipvsadm -Lcn --persistent-conn Problematic SIP messages are SIP responses having "Call-ID" header positioned just after message first line: SIP/2.0 200 OK [Call-ID header here] [rest of the headers] When "Call-ID" header is positioned down (after a few other headers) it is correctly recognized. This is due to the data offset used in get_callid function call inside ip_vs_pe_sip.c file: since dptr already points to the start of the SIP message, the value of dataoff should be initially 0. Otherwise the header is searched starting from some bytes after the first character of the SIP message. Fixes: 758ff033 ("IPVS: sip persistence engine") Signed-off-by:
Marco Angaroni <marcoangaroni@gmail.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Srinivas Kandagatla authored
commit 732d6913 upstream. This patch corrects the enable register offset which is actually 0x36cc instead of 0x36c4 Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Fixes: 5f775498 ("clk: qcom: Fully support apq8064 global clock control") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Sushaanth Srirangapathi authored
commit 713fced8 upstream. Commit 028cd86b ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse") fixes polarities of HSYNC/VSYNC pulse but forgot to update known_lcd_panels[] which had sync values according to old logic. This breaks LCD at least on DA850 EVM. This patch fixes this issue and I have tested this for panel "Sharp_LK043T1DG01" using DA850 EVM board. Fixes: 028cd86b ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse") Signed-off-by:
Sushaanth Srirangapathi <sushaanth.s@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit 712a8038 upstream. When the ssm4567 is powered up the driver calles regcache_sync() to restore the register map content. regcache_sync() assumes that the device is in its power-on reset state. Make sure that this is the case by explicitly resetting the ssm4567 register map before calling regcache_sync() otherwise we might end up with a incorrect register map which leads to undefined behaviour. One such undefined behaviour was observed when returning from system suspend while a playback stream is active, in that case the ssm4567 was kept muted after resume. Fixes: 1ee44ce0 ("ASoC: ssm4567: Add driver for Analog Devices SSM4567 amplifier") Reported-by:
Harsha Priya <harshapriya.n@intel.com> Tested-by:
Fang, Yang A <yang.a.fang@intel.com> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Or Gerlitz authored
commit 6b6c07bd upstream. The command timeout is terribly long, whole two hours. Make it 60s so if things do go wrong, the user gets feedback in relatively short time, so they can take corrective actions and/or investigate using tools and such. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Grazvydas Ignotas authored
commit 5d74325a upstream. The patch that added Logitech Dual Action gamepad support forgot to update the special driver list for the device. This caused the logitech driver not to probe unless kernel module load order was favorable. Update the special driver list to fix it. Thanks to Simon Wood for the idea. Cc: Vitaly Katraew <zawullon@gmail.com> Fixes: 56d0c8b7 ("HID: add support for Logitech Dual Action gamepads") Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Ben Hutchings authored
commit 50e6315d upstream. Commit 985087db 'misc: add support for bmp18x chips to the bmp085 driver' changed the BMP085 config symbol to a boolean. I see no reason why the shared code cannot be built as a module, so change it back to tristate. Fixes: 985087db ("misc: add support for bmp18x chips to the bmp085 driver") Cc: Eric Andersson <eric.andersson@unixphere.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Heiko Stuebner authored
commit 50359819 upstream. Commit e6d5e7d9 ("clk-divider: Fix READ_ONLY when divider > 1") removed the special ops struct for read-only clocks and instead opted to handle them inside the regular ops. On the rk3368 this results in breakage as aclkm now gets set a value. While it is the same divider value, the A53 core still doesn't like it, which can result in the cpu ending up in a hang. The reason being that "ACLKENMasserts one clock cycle before the rising edge of ACLKM" and the clock should only be touched when STANDBYWFIL2 is asserted. To fix this, reintroduce the read-only ops but do include the round_rate callback. That way no writes that may be unsafe are done to the divider register in any case. The Rockchip use of the clk_divider_ops is adapted to this split again, as is the nxp, lpc18xx-ccu driver that was included since the original commit. On lpc18xx-ccu the divider seems to always be read-only so only uses the new ops now. Fixes: e6d5e7d9 ("clk-divider: Fix READ_ONLY when divider > 1") Reported-by:
Zhang Qing <zhangqing@rock-chips.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Arnd Bergmann authored
commit 3deb9438 upstream. gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl function: drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl': drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation] kbuff_arr[i] = NULL; ^~~~~~~~~ drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not if (kbuff_arr[i]) ^~ The code is actually correct, as there is no downside in clearing a NULL pointer again. This clarifies the code and avoids the warning by adding extra curly braces. Signed-off-by:
Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by:
-
Dan Carpenter authored
commit 3af0d554 upstream. There were two issues here: 1) dma_mapping_error() return true/false but we want to return -ENOMEM 2) If dmaengine_prep_slave_sg() failed then "err" wasn't set but presumably that should be -ENOMEM as well. I changed the success path to "return 0;" instead of "return ret;" for clarity. Fixes: 94fe8c68 ('ks8842: Support DMA when accessed via timberdale') Signed-off-by:
-
Xin Long authored
commit 39d2adeb upstream. prior to this patch, at the beginning if we have two paths in one assoc, they may have the same params other than the last_time_heard, it will try the paths like this: 1st cycle try trans1 fail. then trans2 is selected.(cause it's last_time_heard is after trans1). 2nd cycle: try trans2 fail then trans2 is selected.(cause it's last_time_heard is after trans1). 3rd cycle: try trans2 fail then trans2 is selected.(cause it's last_time_heard is after trans1). .... trans1 will never have change to be selected, which is not what we expect. we should keeping round robin all the paths if they are just added at the beginning. So at first every tranport's last_time_heard should be initialized 0, so that we ensure they have the same value at the beginning, only by this, all the transports could get equal chance to be selected. Then for sctp_trans_elect_best, it should return the trans_next one when *trans == *trans_next, so that we can try next if it fails, but now it always return trans. so we can fix it by exchanging these two params when we calls sctp_trans_elect_tie(). Fixes: 4c47af4d ('net: sctp: rework multihoming retransmission path selection to rfc4960') Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
commit 362210e0 upstream. A cleanup patch in linux-3.18 moved around some code in the ath9k driver and left some code to be indented in a misleading way, made worse by the addition of some new code for p2p mode, as discovered by a new gcc-6 warning: drivers/net/wireless/ath/ath9k/init.c: In function 'ath9k_set_hw_capab': drivers/net/wireless/ath/ath9k/init.c:851:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation] hw->wiphy->iface_combinations = if_comb; ^~ drivers/net/wireless/ath/ath9k/init.c:847:3: note: ...this 'if' clause, but it is not if (ath9k_is_chanctx_enabled()) ^~ The code is in fact correct, but the indentation is not, so I'm reformatting it as it should have been after the original cleanup. Signed-off-by:
-
Arnaldo Carvalho de Melo authored
commit 34b88a68 upstream. The syzkaller fuzzer hit the following use-after-free: Call Trace: [<ffffffff8175ea0e>] __asan_report_load8_noabort+0x3e/0x40 mm/kasan/report.c:295 [<ffffffff851cc31a>] __sys_recvmmsg+0x6fa/0x7f0 net/socket.c:2261 [< inline >] SYSC_recvmmsg net/socket.c:2281 [<ffffffff851cc57f>] SyS_recvmmsg+0x16f/0x180 net/socket.c:2270 [<ffffffff86332bb6>] entry_SYSCALL_64_fastpath+0x16/0x7a arch/x86/entry/entry_64.S:185 And, as Dmitry rightly assessed, that is because we can drop the reference and then touch it when the underlying recvmsg calls return some packets and then hit an error, which will make recvmmsg to set sock->sk->sk_err, oops, fix it. Reported-and-Tested-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Kostya Serebryany <kcc@google.com> Cc: Sasha Levin <sasha.levin@oracle.com> Fixes: a2e27255 ("net: Introduce recvmmsg socket syscall") http://lkml.kernel.org/r/20160122211644.GC2470@redhat.comSigned-off-by:
-
Michal Kazior authored
commit 2a58d42c upstream. The driver can access the queue simultanously while mac80211 tears down the interface. Without spinlock protection this could lead to corrupting sk_buff_head and subsequently to an invalid pointer dereference. Fixes: ba8c3d6f ("mac80211: add an intermediate software queue implementation") Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Vineet Gupta authored
commit 2a41b6dc upstream. commit 80f42084 removed the ARC bitops microoptimization but failed to prune the comments to same effect Fixes: 80f42084 ("ARC: Make ARC bitops "safer" (add anti-optimization)") Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Shawn Lin authored
commit 2467b674 upstream. Add free memeory if rockchip_clk_register_branch fails. Fixes: a245fecb ("clk: rockchip: add basic infrastructure...") Signed-off-by:
-
Dan Carpenter authored
commit 227f33be upstream. We could end up dereferencing an error pointer when we call regulator_disable(). Fixes: 4bdcb1dd ('net: Add MDIO bus driver for the Allwinner EMAC') Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Guillaume Nault authored
commit 1f461dcd upstream. Let channels hold a reference on their network namespace. Some channel types, like ppp_async and ppp_synctty, can have their userspace controller running in a different namespace. Therefore they can't rely on them to preclude their netns from being removed from under them. ================================================================== BUG: KASAN: use-after-free in ppp_unregister_channel+0x372/0x3a0 at addr ffff880064e217e0 Read of size 8 by task syz-executor/11581 ============================================================================= BUG net_namespace (Not tainted): kasan: bad access detected ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in copy_net_ns+0x6b/0x1a0 age=92569 cpu=3 pid=6906 [< none >] ___slab_alloc+0x4c7/0x500 kernel/mm/slub.c:2440 [< none >] __slab_alloc+0x4c/0x90 kernel/mm/slub.c:2469 [< inline >] slab_alloc_node kernel/mm/slub.c:2532 [< inline >] slab_alloc kernel/mm/slub.c:2574 [< none >] kmem_cache_alloc+0x23a/0x2b0 kernel/mm/slub.c:2579 [< inline >] kmem_cache_zalloc kernel/include/linux/slab.h:597 [< inline >] net_alloc kernel/net/core/net_namespace.c:325 [< none >] copy_net_ns+0x6b/0x1a0 kernel/net/core/net_namespace.c:360 [< none >] create_new_namespaces+0x2f6/0x610 kernel/kernel/nsproxy.c:95 [< none >] copy_namespaces+0x297/0x320 kernel/kernel/nsproxy.c:150 [< none >] copy_process.part.35+0x1bf4/0x5760 kernel/kernel/fork.c:1451 [< inline >] copy_process kernel/kernel/fork.c:1274 [< none >] _do_fork+0x1bc/0xcb0 kernel/kernel/fork.c:1723 [< inline >] SYSC_clone kernel/kernel/fork.c:1832 [< none >] SyS_clone+0x37/0x50 kernel/kernel/fork.c:1826 [< none >] entry_SYSCALL_64_fastpath+0x16/0x7a kernel/arch/x86/entry/entry_64.S:185 INFO: Freed in net_drop_ns+0x67/0x80 age=575 cpu=2 pid=2631 [< none >] __slab_free+0x1fc/0x320 kernel/mm/slub.c:2650 [< inline >] slab_free kernel/mm/slub.c:2805 [< none >] kmem_cache_free+0x2a0/0x330 kernel/mm/slub.c:2814 [< inline >] net_free kernel/net/core/net_namespace.c:341 [< none >] net_drop_ns+0x67/0x80 kernel/net/core/net_namespace.c:348 [< none >] cleanup_net+0x4e5/0x600 kernel/net/core/net_namespace.c:448 [< none >] process_one_work+0x794/0x1440 kernel/kernel/workqueue.c:2036 [< none >] worker_thread+0xdb/0xfc0 kernel/kernel/workqueue.c:2170 [< none >] kthread+0x23f/0x2d0 kernel/drivers/block/aoe/aoecmd.c:1303 [< none >] ret_from_fork+0x3f/0x70 kernel/arch/x86/entry/entry_64.S:468 INFO: Slab 0xffffea0001938800 objects=3 used=0 fp=0xffff880064e20000 flags=0x5fffc0000004080 INFO: Object 0xffff880064e20000 @offset=0 fp=0xffff880064e24200 CPU: 1 PID: 11581 Comm: syz-executor Tainted: G B 4.4.0+ Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.2-0-g33fbe13 by qemu-project.org 04/01/2014 00000000ffffffff ffff8800662c7790 ffffffff8292049d ffff88003e36a300 ffff880064e20000 ffff880064e20000 ffff8800662c77c0 ffffffff816f2054 ffff88003e36a300 ffffea0001938800 ffff880064e20000 0000000000000000 Call Trace: [< inline >] __dump_stack kernel/lib/dump_stack.c:15 [<ffffffff8292049d>] dump_stack+0x6f/0xa2 kernel/lib/dump_stack.c:50 [<ffffffff816f2054>] print_trailer+0xf4/0x150 kernel/mm/slub.c:654 [<ffffffff816f875f>] object_err+0x2f/0x40 kernel/mm/slub.c:661 [< inline >] print_address_description kernel/mm/kasan/report.c:138 [<ffffffff816fb0c5>] kasan_report_error+0x215/0x530 kernel/mm/kasan/report.c:236 [< inline >] kasan_report kernel/mm/kasan/report.c:259 [<ffffffff816fb4de>] __asan_report_load8_noabort+0x3e/0x40 kernel/mm/kasan/report.c:280 [< inline >] ? ppp_pernet kernel/include/linux/compiler.h:218 [<ffffffff83ad71b2>] ? ppp_unregister_channel+0x372/0x3a0 kernel/drivers/net/ppp/ppp_generic.c:2392 [< inline >] ppp_pernet kernel/include/linux/compiler.h:218 [<ffffffff83ad71b2>] ppp_unregister_channel+0x372/0x3a0 kernel/drivers/net/ppp/ppp_generic.c:2392 [< inline >] ? ppp_pernet kernel/drivers/net/ppp/ppp_generic.c:293 [<ffffffff83ad6f26>] ? ppp_unregister_channel+0xe6/0x3a0 kernel/drivers/net/ppp/ppp_generic.c:2392 [<ffffffff83ae18f3>] ppp_asynctty_close+0xa3/0x130 kernel/drivers/net/ppp/ppp_async.c:241 [<ffffffff83ae1850>] ? async_lcp_peek+0x5b0/0x5b0 kernel/drivers/net/ppp/ppp_async.c:1000 [<ffffffff82c33239>] tty_ldisc_close.isra.1+0x99/0xe0 kernel/drivers/tty/tty_ldisc.c:478 [<ffffffff82c332c0>] tty_ldisc_kill+0x40/0x170 kernel/drivers/tty/tty_ldisc.c:744 [<ffffffff82c34943>] tty_ldisc_release+0x1b3/0x260 kernel/drivers/tty/tty_ldisc.c:772 [<ffffffff82c1ef21>] tty_release+0xac1/0x13e0 kernel/drivers/tty/tty_io.c:1901 [<ffffffff82c1e460>] ? release_tty+0x320/0x320 kernel/drivers/tty/tty_io.c:1688 [<ffffffff8174de36>] __fput+0x236/0x780 kernel/fs/file_table.c:208 [<ffffffff8174e405>] ____fput+0x15/0x20 kernel/fs/file_table.c:244 [<ffffffff813595ab>] task_work_run+0x16b/0x200 kernel/kernel/task_work.c:115 [< inline >] exit_task_work kernel/include/linux/task_work.h:21 [<ffffffff81307105>] do_exit+0x8b5/0x2c60 kernel/kernel/exit.c:750 [<ffffffff813fdd20>] ? debug_check_no_locks_freed+0x290/0x290 kernel/kernel/locking/lockdep.c:4123 [<ffffffff81306850>] ? mm_update_next_owner+0x6f0/0x6f0 kernel/kernel/exit.c:357 [<ffffffff813215e6>] ? __dequeue_signal+0x136/0x470 kernel/kernel/signal.c:550 [<ffffffff8132067b>] ? recalc_sigpending_tsk+0x13b/0x180 kernel/kernel/signal.c:145 [<ffffffff81309628>] do_group_exit+0x108/0x330 kernel/kernel/exit.c:880 [<ffffffff8132b9d4>] get_signal+0x5e4/0x14f0 kernel/kernel/signal.c:2307 [< inline >] ? kretprobe_table_lock kernel/kernel/kprobes.c:1113 [<ffffffff8151d355>] ? kprobe_flush_task+0xb5/0x450 kernel/kernel/kprobes.c:1158 [<ffffffff8115f7d3>] do_signal+0x83/0x1c90 kernel/arch/x86/kernel/signal.c:712 [<ffffffff8151d2a0>] ? recycle_rp_inst+0x310/0x310 kernel/include/linux/list.h:655 [<ffffffff8115f750>] ? setup_sigcontext+0x780/0x780 kernel/arch/x86/kernel/signal.c:165 [<ffffffff81380864>] ? finish_task_switch+0x424/0x5f0 kernel/kernel/sched/core.c:2692 [< inline >] ? finish_lock_switch kernel/kernel/sched/sched.h:1099 [<ffffffff81380560>] ? finish_task_switch+0x120/0x5f0 kernel/kernel/sched/core.c:2678 [< inline >] ? context_switch kernel/kernel/sched/core.c:2807 [<ffffffff85d794e9>] ? __schedule+0x919/0x1bd0 kernel/kernel/sched/core.c:3283 [<ffffffff81003901>] exit_to_usermode_loop+0xf1/0x1a0 kernel/arch/x86/entry/common.c:247 [< inline >] prepare_exit_to_usermode kernel/arch/x86/entry/common.c:282 [<ffffffff810062ef>] syscall_return_slowpath+0x19f/0x210 kernel/arch/x86/entry/common.c:344 [<ffffffff85d88022>] int_ret_from_sys_call+0x25/0x9f kernel/arch/x86/entry/entry_64.S:281 Memory state around the buggy address: ffff880064e21680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff880064e21700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff880064e21780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff880064e21800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff880064e21880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Fixes: 273ec51d ("net: ppp_generic - introduce net-namespace functionality v2") Reported-by:
Baozeng Ding <sploving1@gmail.com> Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Reviewed-by:
Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by:
-
Arnd Bergmann authored
commit 13aa38e2 upstream. The Xen framebuffer driver selects the xen keyboard driver, so the latter will be built-in if XEN_FBDEV_FRONTEND=y. However, when CONFIG_INPUT is a loadable module, this configuration cannot work. On mainline kernels, the symbol will be enabled but not used, while in combination with a patch I have to detect such useless configurations, we get the expected link failure: drivers/input/built-in.o: In function `xenkbd_remove': xen-kbdfront.c:(.text+0x2f0): undefined reference to `input_unregister_device' xen-kbdfront.c:(.text+0x30e): undefined reference to `input_unregister_device' This removes the extra "select", as it just causes more trouble than it helps. In theory, some defconfig file might break if it has XEN_FBDEV_FRONTEND in it but not INPUT_XEN_KBDDEV_FRONTEND. The Kconfig fragment we ship in the kernel (kernel/configs/xen.config) however already enables both, and anyone using an old .config file would keep having both enabled. Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Fixes: 36c1132e ("xen kconfig: fix select INPUT_XEN_KBDDEV_FRONTEND") Acked-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by:
-
Stephen Boyd authored
commit 0f75e1a3 upstream. The offset seems to have been copied from the sata clk. Fix it so that enabling the crypto engine source clk works. Tested-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: 5f775498 ("clk: qcom: Fully support apq8064 global clock control") Signed-off-by:
-
Loc Ho authored
commit 0f4c7a13 upstream. In the initial fix for non-zero divider shift value, the parenthesis was missing after the negate operation. This patch adds the required parenthesis. Otherwise, lower bits may be cleared unintentionally. Signed-off-by:
Loc Ho <lho@apm.com> Acked-by:
Toan Le <toanle@apm.com> Fixes: 1382ea63 ("clk: xgene: Fix divider with non-zero shift value") Signed-off-by:
-
