- 06 Jun, 2019 18 commits
-
-
Robert Hancock authored
Add 1000BaseX to the link modes which are detected based on the MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which support 1000BaseX to work properly with drivers using phylink. Previously 1000BaseX support was not detected, and if that was the only mode the PHY indicated support for, phylink would refuse to attach it due to the list of supported modes being empty. Signed-off-by:
Robert Hancock <hancock@sedsystems.ca> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
YueHaibing authored
Fix sparse warning: drivers/net/ethernet/mscc/ocelot_ace.c:96:3: warning: symbol 'vcap_data_t' was not declared. Should it be static? 'vcap_data_t' never used so can be removed Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Fabio Estevam authored
When a valid MAC address is not found the current messages are shown: fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa Since the network device has not been registered at this point, it is better to use dev_err()/dev_info() instead, which will provide cleaner log messages like these: fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa Tested on a imx6dl-pico-pi board. Signed-off-by:
Fabio Estevam <festevam@gmail.com> Signed-off-by:
-
Litao jiao authored
The monolithic hash_lock could cause huge contention when inserting/deletiing vxlan_fdbs into the fdb_head. Use FDB_HASH_SIZE hash_locks to protect insertions/deletions of vxlan_fdbs into the fdb_head hash table. Suggested-by:
Litao jiao <jiaolitao@raisecom.com> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a NL_SET_ERR_MSG message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Heiner Kallweit authored
The opts[] array is of type u32. Therefore remove the wrong cpu_to_le32(). The opts[] array members are converted to little endian later when being assigned to the respective descriptor fields. This is not a new issue, it just popped up due to r8169.c having been renamed and more thoroughly checked. Due to the renaming this patch applies to net-next only. Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== ipv6: tcp: more control on RST flowlabels First patch allows to reflect incoming IPv6 flowlabel on RST packets sent when no socket could handle the packet. Second patch makes sure we send the same flowlabel for RST or ACK packets on behalf of TIME_WAIT sockets. ==================== Signed-off-by: -
Eric Dumazet authored
After commit 1d13a96c ("ipv6: tcp: fix flowlabel value in ACK messages"), we stored in tw_flowlabel the flowlabel, in the case ACK packets needed to be sent on behalf of a TIME_WAIT socket. We can use the same field so that RST packets sent from TIME_WAIT state also use a consistent flowlabel. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Florent Fourcot <florent.fourcot@wifirst.fr> Signed-off-by:
-
Eric Dumazet authored
When RST packets are sent because no socket could be found, it makes sense to use flowlabel_reflect sysctl to decide if a reflection of the flowlabel is requested. This extends commit 22b6722b ("ipv6: Add sysctl for per namespace flow label reflection"), for some TCP RST packets. In order to provide full control of this new feature, flowlabel_reflect becomes a bitmask. Signed-off-by:
-
Gustavo A. R. Silva authored
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct objagg_stats { ... struct objagg_obj_stats_info stats_info[]; }; size = sizeof(*objagg_stats) + sizeof(objagg_stats->stats_info[0]) * count; instance = kzalloc(size, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = kzalloc(struct_size(instance, stats_info, count), GFP_KERNEL); Notice that, in this case, variable alloc_size is not necessary, hence it is removed. This code was detected with the help of Coccinelle. Signed-off-by:Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Zhiqiang Liu authored
small cleanup: "struct request_sock_queue *queue" parameter of reqsk_queue_unlink func is never used in the func, so we can remove it. Signed-off-by:
Zhiqiang Liu <liuzhiqiang26@huawei.com> Reviewed-by:
-
Heiner Kallweit authored
In the early days of phylib we had a functionality that changed to the next lower speed in fixed mode if no link was established after a certain period of time. This functionality has been removed years ago, and state PHY_FORCING isn't needed any longer. Instead we can go from UP to RUNNING or NOLINK directly (same as in autoneg mode). Signed-off-by:
-
Zhu Yanjun authored
The variable cache_allocs is to indicate how many frags (KiB) are in one rds connection frag cache. The command "rds-info -Iv" will output the rds connection cache statistics as below: " RDS IB Connections: LocalAddr RemoteAddr Tos SL LocalDev RemoteDev 1.1.1.14 1.1.1.14 58 255 fe80::2:c903:a:7a31 fe80::2:c903:a:7a31 send_wr=256, recv_wr=1024, send_sge=8, rdma_mr_max=4096, rdma_mr_size=257, cache_allocs=12 " This means that there are about 12KiB frag in this rds connection frag cache. Since rds.h in rds-tools is not related with the kernel rds.h, the change in kernel rds.h does not affect rds-tools. rds-info in rds-tools 2.0.5 and 2.0.6 is tested with this commit. It works well. Signed-off-by:Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by:
-
David S. Miller authored
Biao Huang says: ==================== complete dwmac-mediatek driver and fix flow control issue Changes in v2: patch#1: there is no extra action in mediatek_dwmac_remove, remove it v1: This series mainly complete dwmac-mediatek driver: 1. add power on/off operations for dwmac-mediatek. 2. disable rx watchdog to reduce rx path reponding time. 3. change the default value of tx-frames from 25 to 1, so ptp4l will test pass by default. and also fix the issue that flow control won't be disabled any more once being enabled. ==================== Signed-off-by: -
Biao Huang authored
Current dwmac4_flow_ctrl will not clear GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits, so MAC hw will keep flow control on although expecting flow control off by ethtool. Add codes to fix it. Fixes: 477286b5 ("stmmac: add GMAC4 core support") Signed-off-by:
Biao Huang <biao.huang@mediatek.com> Signed-off-by:
-
Biao Huang authored
the default value of tx-frames is 25, it's too late when passing tstamp to stack, then the ptp4l will fail: ptp4l -i eth0 -f gPTP.cfg -m ptp4l: selected /dev/ptp0 as PTP clock ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE ptp4l: port 1: link up ptp4l: timed out while polling for tx timestamp ptp4l: increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug ptp4l: port 1: send peer delay response failed ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED) ptp4l tests pass when changing the tx-frames from 25 to 1 with ethtool -C option. It should be fine to set tx-frames default value to 1, so ptp4l will pass by default. Signed-off-by: -
Biao Huang authored
disable rx watchdog for dwmac-mediatek, then the hw will issue a rx interrupt once receiving a packet, so the responding time for rx path will be reduced. Signed-off-by:
-
Biao Huang authored
add Ethernet power on/off operations in init/exit flow. Signed-off-by:
-
- 05 Jun, 2019 22 commits
-
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra likely() call around the !IS_ERR() is not needed. Signed-off-by:
Enrico Weigelt <info@metux.net> Signed-off-by:
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra unlikely() call around IS_ERR() is not needed. Signed-off-by:
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra unlikely() call around IS_ERR() is not needed. Signed-off-by:
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra likely() call around the !IS_ERR() is not needed. Signed-off-by:
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra likely() call around the !IS_ERR() is not needed. Signed-off-by:
-
Gustavo A. R. Silva authored
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct nfp_tun_active_tuns { ... struct route_ip_info { __be32 ipv4; __be32 egress_port; __be32 extra[2]; } tun_info[]; }; Make use of the struct_size() helper instead of an open-coded version in order to avoid any potential type mistakes. So, replace the following form: sizeof(struct nfp_tun_active_tuns) + sizeof(struct route_ip_info) * count with: struct_size(payload, tun_info, count) This code was detected with the help of Coccinelle. Signed-off-by:Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Lihong Yang authored
The PF driver state flag __I40E_VIRTCHNL_OP_PENDING needs to be checked and set at the beginning of i40e_ndo_set_vf_mac. Otherwise, if there are error conditions before it, the flag will be cleared unexpectedly by this function to cause potential race conditions. Hence move the check to the top of this function. Signed-off-by:
Lihong Yang <lihong.yang@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Lihong Yang authored
The VF configuration returned in i40e_ndo_get_vf_config is already stored by the PF. There is no dependency on any specific state of the VF to return the configuration. Drop the check against I40E_VF_STATE_INIT since it is not needed. Signed-off-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2019-06-05 This series contains updates to mainly ixgbe, with a few updates to i40e, net, ice and hns2 driver. Jan adds support for tracking each queue pair for whether or not AF_XDP zero copy is enabled. Also updated the ixgbe driver to use the netdev-provided umems so that we do not need to contain these structures in our own adapter structure. William Tu provides two fixes for AF_XDP statistics which were causing incorrect counts. Jake reduces the PTP transmit timestamp timeout from 15 seconds to 1 second, which is still well after the maximum expected delay. Also fixes an issues with the PTP SDP pin setup which was not properly aligning on a full second, so updated the code to account for the cyclecounter multiplier and simplify the code to make the intent of the calculations more clear. Updated the function header comments to help with the code documentation. Added support for SDP/PPS output for x550 devices, which is slightly different than x540 devices that currently have this support. Anirudh adds a new define for Link Layer Discovery Protocol to the networking core, so that drivers do not have to create and use their own definitions. In addition, update all the drivers currently defining their own LLDP define to use the new networking core define. ==================== Signed-off-by: -
Kangjie Lu authored
If ixgbevf_write_msg_read_ack fails, return its error code upstream Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Tested-by:
Mukesh Ojha <mojha@codeaurora.org> Signed-off-by:
-
Jacob Keller authored
Similar to the X540 hardware, enable support for generating a 1pps output signal on SDP0. This support is slightly different to the X540 hardware, because of the register layout changes. First, the system time register is now represented in 'cycles' and 'billions of cycles'. Second, we need to also program the TSSDP register, as well as the ESDP register. Third, the clock output uses only FREQOUT, instead of a full 64bit value for the output clock period. Finally, we have to use the ST0 bit instead of the SYNCLK bit in the TSAUXC register. This support should work even for the hardware with a higher frequency clock, as it carefully takes into account the multiply and shift of the cycle counter used. We also set the pps configuration to 1, since we now support generating a pulse per second output. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Anirudh Venkataramanan authored
Remove references to HCLGE_MAC_ETHERTYPE_LLDP and use ETH_P_LLDP instead. Signed-off-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
-
Jeff Kirsher authored
Instead of using a local define for the LLDP ethertype, use the kernel define ETH_P_LLDP. Signed-off-by: -
Anirudh Venkataramanan authored
Remove references to IXGBE_ETH_P_LLD and use ETH_P_LLDP instead. Signed-off-by:
-
Anirudh Venkataramanan authored
Remove references to I40E_ETH_P_LLDP and use ETH_P_LLDP instead. Signed-off-by:
-
Anirudh Venkataramanan authored
Add a new define ETH_P_LLDP for Link Layer Discovery Protocol (LLDP) ethertype. Suggested-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
-
Jacob Keller authored
This function was missing a documentation comment. Add one now. Signed-off-by:
-
Jacob Keller authored
The ixgbe_ptp.c file sometimes uses hw_cc as the local variable for the cycle counter in ixgbe_ptp_read_X550. However, we use just 'cc' as a local variable for this by convention else where in the file. Convert this lone usage of 'hw_cc' into just the shorter 'cc' name to match the other read functions in the file. Signed-off-by:
-
Jacob Keller authored
The function ixgbe_ptp_setup_sdp_X540 attempts to program a software defined pin, in order to generate a pulse-per-second output on SDP 0. It does work to generate the output, but does not align the output on the full second. Additionally, it does not take into account the cyclecounter multiplier. This leads to somewhat confusing code which is likely to be incorrect if blindly copied to another hardware type. Update this code to account for the cyclecounter multiplier, and to directly use timecounter_read. This change ensures that the SDP output will align properly on a full second, and makes the intent of the calculations a bit more clear. Signed-off-by:
-
Jacob Keller authored
Previously we waited for a whole 15 seconds before we cleared the Tx timestamp state. This is astronomically long compared to the worst case timings expected by our devices. In addition, this is longer than the wait in ptp4l when it detects a fault (caused by missing Tx timestamps). Thus, reduce the timer to only 1 second, which is well after the maximum expected delay. This should reduce user frustration when a timestamp does get dropped for some reason. Signed-off-by:
-
William Tu authored
The total_packets count at ixgbe_clean_xdp_tx_irq is always zero when testing with xdpsock -t -N. Set the gso_segs to 1 to make the tx packet count correct. Signed-off-by:
William Tu <u9012063@gmail.com> Tested-by:
-
William Tu authored
The tx bytecount is done twice. When running './xdpsock -t -N -i eth3' and 'ip -s link show dev eth3' The avg packet size is 120 instead of 60. So remove the extra one. Signed-off-by:
-
