Our bus should allow defining children nodes as we may want to specify
devices attached to the bus. This is required e.g. to specify NAND or
ChipCommon cores and use bus's address and IRQ mappings.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch fixes following issues in p2p code paths.

1) bss role, bss type and connection type was not set correctly
for p2p GO and p2p client at couple of places.
2) Driver appends a proprietary header to management frames
which will be parsed by our firmware. Later while informing
TX status to cfg80211, modified frame buffer was passed to
cfg80211_mgmt_tx_status() instead of original one.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.

Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.

To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When wlcore_probe_of failed, return the correct error code instead of ENOMEM
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This fixes a typo in the "b43_lo_g_maintenance_work" function
name.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This fixes a typo in two comments: "paht" -> "path".
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There is an error that can occur where the driver adds the same URB to USB submission list twice.
This happens since mwifiex_usb_submit_rem_rx can submit packets at same time as an rx urb complete callback.
This causes list corruption and is fixed by not setting the skb to NULL when submitting an rx packet.

[   84.461242] WARNING: CPU: 1 PID: 748 at lib/list_debug.c:36 __list_add+0xcb/0xd0()
[   84.461245] list_add double add: new=ffff8800c92b0c50, prev=ffff8800c92b0c50, next=ffff8800ced6c430.
[   84.461247] Modules linked in: rfcomm fuse cmac nf_conntrack_netbios_ns nf_conntrack_broadcast ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack bnep iptable_mangle iptable_security iptable_raw btusb btintel bluetooth mwifiex_usb mwifiex x86_pkg_temp_thermal cfg80211 coretemp r8712u(C) kvm_intel kvm hid_sensor_als hid_sensor_incl_3d hid_sensor_rotation hid_sensor_magn_3d hid_sensor_accel_3d hid_sensor_gyro_3d hid_sensor_trigger hid_sensor_iio_common industrialio_triggered_buffer kfifo_buf rfkill iTCO_wdt industrialio iTCO_vendor_support
[   84.461316]  crc32_pclmul crc32c_intel ghash_clmulni_intel microcode snd_hda_codec_realtek vfat snd_hda_codec_generic fat snd_hda_codec_hdmi snd_hda_intel snd_hda_controller uvcvideo snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hwdep videobuf2_core snd_hda_core joydev v4l2_common videodev hid_sensor_hub snd_seq hid_multitouch media snd_seq_device snd_pcm snd_timer mei_me snd i2c_i801 lpc_ich mei soundcore tpm_infineon tpm_tis tpm i2c_hid i2c_designware_platform i2c_designware_core nfsd auth_rpcgss nfs_acl lockd grace sunrpc sch_fq_codel i915 i2c_algo_bit drm_kms_helper drm xhci_pci xhci_hcd ehci_pci sd_mod ehci_hcd video
[   84.461383] CPU: 1 PID: 748 Comm: kworker/u9:0 Tainted: G         C      4.1.0-rc5+ #163
[   84.461386] Hardware name: Microsoft Corporation Surface Pro 2/Surface Pro 2, BIOS 2.05.0250 04/10/2015
[   84.461396] Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex]
[   84.461399]  ffffffff81a8150e ffff8801174cf8e8 ffffffff817df830 0000000000000000
[   84.461405]  ffff8801174cf938 ffff8801174cf928 ffffffff810a54ba ffff8800c86bd750
[   84.461410]  ffff8800c92b0c50 ffff8800c92b0c50 ffff8800ced6c430 ffff88010c057178
[   84.461416] Call Trace:
[   84.461421]  [<ffffffff817df830>] dump_stack+0x4f/0x7b
[   84.461428]  [<ffffffff810a54ba>] warn_slowpath_common+0x8a/0xc0
[   84.461432]  [<ffffffff810a5536>] warn_slowpath_fmt+0x46/0x50
[   84.461436]  [<ffffffff814109fb>] __list_add+0xcb/0xd0
[   84.461442]  [<ffffffff815c551a>] ? usb_hcd_link_urb_to_ep+0x2a/0xa0
[   84.461446]  [<ffffffff815c5570>] usb_hcd_link_urb_to_ep+0x80/0xa0
[   84.461459]  [<ffffffffa004318a>] prepare_transfer+0xaa/0x130 [xhci_hcd]
[   84.461470]  [<ffffffffa0044cf7>] xhci_queue_bulk_tx+0xb7/0x7a0 [xhci_hcd]
[   84.461480]  [<ffffffffa003b67f>] ? xhci_urb_enqueue+0x50f/0x660 [xhci_hcd]
[   84.461489]  [<ffffffffa003b67f>] ? xhci_urb_enqueue+0x50f/0x660 [xhci_hcd]
[   84.461498]  [<ffffffffa003b735>] xhci_urb_enqueue+0x5c5/0x660 [xhci_hcd]
[   84.461503]  [<ffffffff815c7ad3>] usb_hcd_submit_urb+0x93/0xa70
[   84.461507]  [<ffffffff8168dde8>] ? __alloc_skb+0x78/0x1f0
[   84.461511]  [<ffffffff8168d301>] ? __kmalloc_reserve.isra.26+0x31/0x90
[   84.461515]  [<ffffffff8168ddbc>] ? __alloc_skb+0x4c/0x1f0
[   84.461519]  [<ffffffff8168ddfc>] ? __alloc_skb+0x8c/0x1f0
[   84.461523]  [<ffffffff8168badd>] ? skb_dequeue+0x5d/0x80
[   84.461527]  [<ffffffff815c987e>] usb_submit_urb+0x42e/0x5f0
[   84.461531]  [<ffffffff816931d9>] ? __alloc_rx_skb+0x39/0x100
[   84.461536]  [<ffffffffa05aa372>] mwifiex_usb_submit_rx_urb+0xb2/0x170 [mwifiex_usb]
[   84.461542]  [<ffffffffa05aa5f5>] mwifiex_usb_submit_rem_rx_urbs+0x45/0x50 [mwifiex_usb]
[   84.461550]  [<ffffffffa07094be>] mwifiex_rx_work_queue+0x10e/0x140 [mwifiex]
[   84.461556]  [<ffffffff810c4429>] process_one_work+0x229/0x890
[   84.461559]  [<ffffffff810c438c>] ? process_one_work+0x18c/0x890
[   84.461565]  [<ffffffff810c4ae3>] worker_thread+0x53/0x470
[   84.461569]  [<ffffffff810c4a90>] ? process_one_work+0x890/0x890
[   84.461572]  [<ffffffff810cb162>] kthread+0xf2/0x110
[   84.461577]  [<ffffffff811031ad>] ? trace_hardirqs_on+0xd/0x10
[   84.461581]  [<ffffffff810cb070>] ? kthread_create_on_node+0x230/0x230
[   84.461586]  [<ffffffff817e9662>] ret_from_fork+0x42/0x70
[   84.461590]  [<ffffffff810cb070>] ? kthread_create_on_node+0x230/0x230
[   84.461593] ---[ end trace 65103af5e6fb3444 ]---
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Storage pointed to by gen_ie is allocated with kmalloc, but was
never freed.

Coverity CID #1271251
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Amit & Nishant would be taking care of maintaining mwifiex driver here
onwards on account of organizational changes.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Without this change, the code simply exits after calling
mwifiex_uap_set_head_tail_ies, leving the call to
mwifiex_set_mgmt_beacon_data_ies as dead code.

Coverity CID #1271292
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex_set_wowlan_mef_entry attempts to free a passed-in pointer in
case of an error.  The only caller (mwifiex_set_mef_filter) passes that
pointer as an offset into allocated memory, so any attempt to free that
will not be the actual allocated pointer.

Address this by changing mwifiex_set_wowlan_mef_entry to not do any
free, and to cause mwifiex_set_mef_filter to do the appropriate free if
the call to mwifiex_set_wowlan_mef_entry fails.

Coverity CID #1295879
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Solomon Peachy <pizza@shaftnet.org>
To: Kalle Valo <kvalo@codeaurora.org>
To: linux-wireless@vger.kernel.org
To: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support to handle multichannel event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Multichannel and DFS cannot be supported at same time. So when multichannel
operation is enabled by module parameter, we enable number of channel as 2
while registering wiphy. For all other cases we advertise DFS support to
cfg80211. Patch also adds support for radar detect widths parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support to advetise mwifiex multichannel support to
cfg80211. If module parameter drcs is enabled and FW supports multichannel
operation we advertise this support to cfg80211. As of now 2 simultaneous
channels are supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for setting multichannel policy as module parameter
to FW. Value of 1 indicates Multichannel support is enabled
and value of 0 disables it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support to extend TX Data pause for AP intefaces.
Also for station role, support for pausing/unpausing all traffic
when mac address parameter is BSSID is added.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support to enable data traffic only when port is open.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for another TX queue in driver- bypass
TX queue. This queue is used for sending data/mgmt packets while
in disconnected state i.e. when port is yet not unblocked.
TDLS setup packets would also be queued in this queue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap. Also we configure 11D
settings info FW only for specific band. So we need to download domain
info to FW even if domain remains unchanged but band is changed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add cfg80211 tdls_chan_switch and tdls_cancel_chan_switch
handler.
With this handlers, mwifiex would support TDLS channel switch feature.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

TDLS link status - channel switching, off channel or base channel itself
indicates that TDLS link is setup.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch enable tdls channel switch ext capability in tdls action
frame, and also configure basic tdls channel switch parameters while
tdls setup completed and tdls link is enabled..
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add support for a new tdls configuration command
which is used for configuration of tdls channel switch parameters.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add support for tdls channel switch event process.
We block TX queues for particular RA list depending upon channel
switch state. If channel switch state is moving to base channel,
we unblock RA lists for AP. If channel switch state is moving to off
channel, we unblock TDLS peer RA lists.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add new tdls status used for tdls channel switch.
Driver in turn would block cmd path and data path if tdls
channel switching. Data path to non tdls peer should be blocked
if tdls channel switch to off-channel.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If tx_pkts_queued is increased for tx paused receive address, tx process
will be triggered for this packet. But since RA list was tx paused,
there will be an infinite loop in mwifiex_wmm_process_tx waiting for the
event(tx pause, tdls cs) to cancel tx pause. This will be an dead loop,
since main_process was locked at this time, there will be no opportunity
to process event.

So do not increase tx_pkts_queued if receive address tx paused,
this will be restored RA list is unpaused.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Data traffic to tx paused receive address should be blocked.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support to enable TX data pause feature for mwifiex.
Whenever FW TX buffers reach threshold, FW would send TX pause event
to driver. Driver in turn would block data traffic to that particular
receiver address.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the rtlwifi/rtl8192cu, rtl8723 code is dead code.
So I remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Major changes in ath10k:

* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch

FCC long pulse radar (type 5) requires pulses to be
checked for chirping. This patch implements chirp
detection based on the FFT data provided for long
pulses.

A chirp is detected when a set of criteria defined
by FCC pulse characteristics is met, including
* have at least 4 FFT samples
* max_bin index moves equidistantly between samples
* the gradient is within defined range

The chirp detection has been tested with reference
radar generating devices and proved to work reliably.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The chip reports radar pulses on extension channel
even if operating in HT20 mode. This patch adds a
sanity check for HT40 mode before it feeds pulses
on extension channel to the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

commit 2c86c275 ("Add ipw2100 wireless driver.") introduced
HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified
by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50
milliseconds thus fixed up to msecs_to_jiffies(50).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.

Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.

This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.

Fixes: b4aa539d ("ath10k: implement tx pause wmi event")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.

Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf98446 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.

This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.

Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>