So far it was possible to have one EMAD register access at a time,
locked by mutex. This patch extends this interface to allow multiple
EMAD register accesses to be in fly at once. That allows faster
processing on firmware side avoiding unused time in between EMADs.
Measured speedup is ~30% for shared occupancy snapshot operation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow-up patch is going to need to use delayed work as well and
frequently. The FDB notification processing is already using that and
also quite frequently. It makes sense to create separate workqueue just
for mlxsw driver in this case and do not pollute system_wq.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since it is not possible to get and clear Port-Pool occupancy data using
SBSR register, there's a need to implement that using SBPM.
Extend pack helper and add unpack helper to get occupancy values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This register allows to query HW for current and maximal buffer usage.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add middle layer in mlxsw core code to forward shared buffer occupancy
calls into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement previously introduced mlxsw core shared buffer API.
For Spectrum, that is done utilizing registers SBPR, SBCM and SBPM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Needed in following patch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although the device supports max_buff magic values 0 and 0xff, these are
not exposed to the user via devlink.
Therefore, adjust the default values to be within configurable range.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit ff6551ec ("mlxsw: spectrum: Correctly
configure headroom size") control packets are directed to priority group
buffer 9 (PG9) in the ports' headroom buffers.

Since we don't want to drop control packets in case they can't be
admitted to the switch's shared buffer we bind PG9 to a different
ingress pool from the one used by all other PGs.

Unlike other PGs, we currently don't expose the binding between PG9 to a
pool and leave it fixed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since there is no congestion control for CPU port traffic, we can change
the CPU port TC binding to pool 0 with min_buff and max_buff zeroed.
Remove initialization for pool egress pool 3 since it is no longer used
by dafault.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to achieve faster dumping of current setting and also in order
to provide possibility to get pool mode without a need to query hardware,
do cache the configuration in driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Be consintent with rest of the registers (pm, cm) and use "pr" here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Structs are in arrays so use array index as pool/tc/prio index. With
that, there is need to maintain separate arrays for ingress and egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pushed them into helper functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add middle layer in mlxsw core code to forward shared buffer calls
into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

User needs to monitor shared buffer occupancy. For that, he issues a
snapshot command in order to instruct hardware to catch current and
maximal occupancy values, and clear command in order to clear the
historical maximal values.

Also port-pool and tc-pool-bind command response messages are extended to
carry occupancy values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define userspace API and drivers API for configuration of shared
buffers. Four basic objects are defined:
shared buffer - attributes are size, number of pools and TCs
pool - chunk of sharedbuffer definition, it has some size and either
       static or dynamic threshold
port pool threshold - to set per-port threshold for each pool
port tc threshold bind - to bind port and TC to specified pool
                         with threshold.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The structure can be packed denser by doing minor rearrangement
of existing elements.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we have the ISS.CGIS bit set, we already know that gPTP interrupt has
happened, so an extra GIS register check at the end of ravb_ptp_interrupt()
seems superfluous.  We can model the gPTP interrupt  handler like all other
dedicated interrupt handlers in the driver and make it *void*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: [mostly] Ethtool RSS configuration

Most of the content [code-wise] in this series is for allowing various
RSS-related configuration via ethtool.

In addition, this also removed an unnecessary versioning scheme between
the drivers and bump the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds support for the following via ethtool:
  - UDP configuration of RSS based on 2-tuple/4-tuple.
  - RSS hash key.
  - RSS indirection table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the required API for passing RSS-related configuration from qede.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inbox drivers don't need versioning scheme in order to guarantee
compatibility, as both qed and qede are compiled from same codebase.
Signed-off-by: Rahul Verma <rahul.verma@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After introduction of ndo_features_check(), we believe that very
specific checks for rare features should not be done in core
networking stack.

No driver uses gso_min_segs yet, so we revert this feature and save
few instructions per tx packet in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The meta_type_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Byte Queue Limits (BQL) support to bcmgenet driver.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcmgenet_isr1() and bcmgenet_isr0() run in hard irq context,
we do not need to block irq again.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By using napi_complete_done(), we allow fine tuning
of /sys/class/net/ethX/gro_flush_timeout for higher GRO aggregation
efficiency for a Gbit NIC.

Check commit 24d2e4a5 ("tg3: use napi_complete_done()") for details.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
sctp: delay calls to sk_data_ready() as much as possible

1st patch is a preparation for the 2nd. The idea is to not call
->sk_data_ready() for every data chunk processed while processing
packets but only once before releasing the socket.

v2: patchset re-checked, small changelog fixes
v3: on patch 2, make use of local vars to make it more readable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently processing of multiple chunks in a single SCTP packet leads to
multiple calls to sk_data_ready, causing multiple wake up signals which
are costy and doesn't make it wake up any faster.

With this patch it will note that the wake up is pending and will do it
before leaving the state machine interpreter, latest place possible to
do it realiably and cleanly.

Note that sk_data_ready events are not dependent on asocs, unlike waking
up writers.

v2: series re-checked
v3: use local vars to cleanup the code, suggested by Jakub Sitnicki
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It wastes space and gets worse as we add new flags, so convert bit-wide
flags to a bitfield.

Currently it already saves 4 bytes in sctp_sock, which are left as holes
in it for now. The whole struct needs packing, which should be done in
another patch.

Note that do_auto_asconf cannot be merged, as explained in the comment
before it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function compiles to 895 bytes of machine code.

Clearly, this isn't a time-critical function.
For one, it has a number of udelay(1) calls.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
bridge: support sending rntl info when we set attributes through sysfs/ioctl

This patchset is used to support sending rntl info to user in some places,
and ensure that whenever those attributes change internally or from sysfs,
that a netlink notification is sent out to listeners.

It also make some adjustment in bridge sysfs so that we can implement this
easily.

I've done some tests on this patchset, like:
[br_sysfs]
  1. change all the attribute values of br or brif:
  $ echo $value > /sys/class/net/br0/bridge/{*}
  $ echo $value > /sys/class/net/br0/brif/eth1/{*}

  2. meanwhile, on another terminal to observe the msg:
  $ bridge monitor

[br_ioctl]
  1. in bridge-utils package, do some changes in br_set, let brctl command
  use ioctl to set attribute:
         if ((ret = set_sysfs(path, value)) < 0) { -->
         if (1) {

  $ brctl set*

  2. meanwhile, on another terminal to observe the msg:
  $ bridge monitor

This test covers all the attributes that brctl and sysfs support to set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.

We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.

Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.

This patch is used for ioctl.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.

We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.

Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.

This patch is used for br_sysfs_if, and we also move br_ifinfo_notify out
of store_flag.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.

We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.

Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.

This patch is used for br_sysfs_br. and we also need to remove some
rtnl_trylock in old functions so that we can call it in a common one.

For group_addr_store, we cannot make it use store_bridge_parm, because
it's not a string-to-long convert, we will add notification on it
individually.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some repetitive codes in stp_state_store, we can remove
them by calling store_bridge_parm.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some repetitive codes in forward_delay_store, we can remove
them by calling store_bridge_parm.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>