Postpone claiming the port until the device is opened, instead of doing
that when the driver is loaded.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We have been using -EBUSY where we should have used -EIO or -ENOMEM,
so let's fix that and also add some diagnostic messages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This will place the joystick's input device into propoer place in sysfs
hierarchy as long as th port has device assigned to it (i.e. it is not
legacy port).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On resume from suspend there is a possibility for multi-byte scancodes
to be handled incorrectly. atkbd_reconnect disables the processing of
scancodes in software by calling atkbd_disable, but the keyboard may
still be active because no disconnect command was sent. Later, software
handling is re-enabled. If a multi-byte scancode sent from the keyboard
straddles the re-enable, only the latter byte(s) will be handled.

In practice, this leads to cases where multi-byte break codes (ex. "e0
4d" - break code for right-arrow) are misread as make codes ("4d" - make
code for numeric 6), leading to one or more unwanted, untyped characters
being interpreted.

The solution implemented here involves sending command f5 (reset
disable) to the keyboard prior to disabling software handling of codes.
Later, the command to re-enable the keyboard is sent only after we are
prepared to handle scancodes.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It is time to switch to system wq instead creating a queue for the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This simplifies error handling and eliminates the need for implementing
remove() method.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch introduces a driver for Cypress All Points Addressable
I2C Trackpad, including the ones in 2012 Samsung Chromebooks.

This device is compatible with MT protocol type B, providing identifiable
contacts.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

devm_* APIs are device managed and make the exit and clean up code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Laxman Dewangan<ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Tegra KBC driver have the default key mapping for 16x8 configuration.
The key mapping can be provided through platform data or through DT
and the mapping varies from platform to platform, hence this default
mapping is not so useful. Remove the default mapping to reduce the code
lines of the driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The NVIDIA's Tegra KBC has maximum 24 pins to make matrix keypad.
Any pin can be configured as row or column. The maximum column pin
can be 8 and maximum row pin can be 16.

Remove the assumption that all first 16 pins will be used as row
and remaining as columns and Add the property for configuring pins
to either row or column from DT. Update the devicetree binding
document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_* for memory, clock, irq, input device allocation. This reduces
code for freeing these resources.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the following build warning when building driver with CONFIG_PM_SLEEP
not selected.

tegra-kbc.c:360:13: warning: 'tegra_kbc_set_keypress_interrupt' defined but not used [-Wunused-function]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds keyreset functionality to the sysrq driver. It allows
certain button/key combinations to be used in order to trigger emergency
reboots.

Redefining the '__weak platform_sysrq_reset_seq' variable is required
to trigger the feature.  Alternatively keys can be passed to the driver
via a module parameter.

This functionality comes from the keyreset driver submitted by
Arve Hjønnevåg in the Android kernel.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver, submitted on behalf of Cypress Semiconductor Corporation and
additional contributors, provides support for the Cypress PS/2 Trackpad.

Original code contributed by Dudley Du (Cypress Semiconductor Corporation),
modified by Kamal Mostafa and Kyle Fazzari.

BugLink: http://launchpad.net/bugs/978807Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Kyle Fazzari <git@status.e4ward.com>
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Herton Krzesinski <herton.krzesinski@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Cypress PS/2 Trackpad (drivers/input/mouse/cypress_ps2.c) needs
this larger cmdbuf[] to handle 8-byte packet responses.
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch brings wacom driver in-sync with input-mt changes
made in release 3.7.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Henrik added new MT routines in release 3.7. This patch is to prepare
for the use of new MT routines.

In the newly added wacom_abs_set_axis() function, the first
if-statement assigns ABS_X/Y for number of contacts less or equal
to 2. So, it is single and 2 finger touch devices. Two finger touch
devices are processed here since they will not use the updated
input_mt_init_slots(), which does not offer benefit to those devices.

input_mt_init_slots() will take care of ABS_X/Y assignment when flags
are not zero. All touch devices with more than two contacts will use
input_mt_init_slots() with non-zero flags.

The second if-statement is for all MT devices, which include two
finger touch devices.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Outputs x8..x0 of the qt2160 can have leds attached to it.
This patch handles those outputs using the generic LED
framework.

The PWM controls available in the chip are used to achieve
different levels of brightness.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds device tree support for imx keypad driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Only use the defines which are defined in the platform_data include
file.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since it suggests to use defines from input.h (ABS_X, ...), also include
the file to make them available.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The datasheet doesn't say anything about writing twice, so this was
probably overlooked.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Don't open code the AC_READ and AC_WRITE macros.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

stmpe touchscreen supports BTN_TOUCH event but doesn't report it. Add
BTN_TOUCH reporting capability to the stmpe touchscreen driver.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver's timer must be set up before enabling IRQ handler, otherwise
bad things may happen.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Popovec <popovec@fei.tuke.sk>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This saves us a few lines of code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This saves us a few lines of code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch to using devm_*() interfaces to manage our resources,
thus will simplify error unwinding a bit.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Failures to build a keymap, request an IRQ, or register input device are
fatal for the driver, therefore the messages should have "error" severity
instead of "debug".
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This matches structure of most other input drivers.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to use proper accessor functions instead of directly poking into
various structures.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use a temporary variable for our parent device (coming from I2C client
structure); we'll be also using it during conversion to managed resources.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The kernel does not contain the symbol SA1100_BITSY so the driver
is never compiled and can be removed safely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>