After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.

Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Enable plug detection interrupt mask in order to get headset
PLUGINT/UNPLUGINT interrupts.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.

This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Phoenix 1.1 supports automatic power on sequence, a
verification is added to use it with new revision of
the chip.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The mux control has 4 elements not 3
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The twl6040 can support more sample rates other than 88.2 and 96k.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch moves all the PCM error handling for clock config
out of trigger() and startup() and into prepare().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch restores the CODEC bias level at resume().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch adds support for the twl6040 headset and handset
MUX controls.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Multiples interrupts can be received. The irq handler is modified
to attend all of them.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Update the codec to use the new twl core register macros
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Use jack framework to enable detection for the headset microphone
and stereo output in the sdp4430.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch adds support for reporting twl6040 headset and
handset jack events.

The machine driver retrieves and report the status  through
twl6040_hs_jack_detect.

A workq is used to debounce of the irq.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

twl4030 series of codecs supports S32_LE with msbits=24.
Replace the S24_LE with S32_LE format, and add constraint
for 24msbit in case of 32 S32_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on

2. Start playback
aplay -fdat -d3 /dev/zero

After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.

Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.

The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Add FM stereo pins to the machine driver and add them as a
dapm widget.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The use of DAPM widgets, and extra routing can cause ordering
problems in the system.
Machine drivers should use the exported direct interface with
SND_SOC_DAPM_HP's event callback to manage the state of the
amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Reduce the amount of duplicated code by using single
event handler for PGA_E to enable the needed channel.
Use the w->shift to pass the channel information to
the handler function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Do not enable the amplifier right after the power has been
restored to the amplifier.
The DAPM_SUPPLY widget turns on the amp early in the DAPM
power walk, and the unmuting of channel happens quite late.
Keeping the amp in SW reset state ensures better muting.
In this way the pop noise coming from other components (codec)
can be filtered out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Use simpler way to avoid setting the same power state
for the amplifier.
Simplifies the check introduced by patch:
ASoC: tpa6130a2: Fix unbalanced regulator disables
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

During playback start the codec has been already powered at
BIAS_ON event time, so there's no need to enable the codec again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

No need to enable the codec at this time.
The codec will be enabled  later by other events
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Otherwise, calling dev_get_drvdata in p1022_ds_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise, calling dev_get_drvdata in mpc8610_hpcd_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

I think this unneededd !! operations just reduce the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch fixes below error:

  CC      sound/soc/nuc900/nuc900-pcm.o
sound/soc/nuc900/nuc900-pcm.c: In function 'nuc900_dma_open':
sound/soc/nuc900/nuc900-pcm.c:267: error: 'nuc900_ac97_data' undeclared (first use in this function)
sound/soc/nuc900/nuc900-pcm.c:267: error: (Each undeclared identifier is reported only once
sound/soc/nuc900/nuc900-pcm.c:267: error: for each function it appears in.)
sound/soc/nuc900/nuc900-pcm.c: At top level:
sound/soc/nuc900/nuc900-pcm.c:337: error: expected ',' or ';' before 'static'
sound/soc/nuc900/nuc900-pcm.c:354: error: 'nuc900_soc_platform_probe' undeclared here (not in a function)
make[3]: *** [sound/soc/nuc900/nuc900-pcm.o] Error 1
make[2]: *** [sound/soc/nuc900] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch fixes below compile warning:

  CC      sound/soc/nuc900/nuc900-ac97.o
sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix below compile error by add a missing ';'.

  CC      sound/soc/nuc900/nuc900-ac97.o
sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:318: error: expected ',' or ';' before 'static'
sound/soc/nuc900/nuc900-ac97.c:405: error: 'nuc900_ac97_drvprobe' undeclared here (not in a function)
make[3]: *** [sound/soc/nuc900/nuc900-ac97.o] Error 1
make[2]: *** [sound/soc/nuc900] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Ensure that we report any errors encountered during reads/writes
in the cache syncing functions.

Remove redundant newline in the source code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Properly free allocated resources in smdk_init() error path.
Add missing platform_device_unregister() in smdk_exit().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Properly free allocated resources in neo1973_gta02_init() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Properly free allocated resources in goni_init() error path.
Add missing snd_soc_unregister_dai() in goni_exit().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>