Implement and advertise unicast MAC filtering, such that setting macvlan
instance over mlx4_en interfaces will not require the networking core
to put mlx4_en devices in promiscuous mode.

If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As a preparation step for supporting multiple unicast addresses, store MAC addresses in hash table.
Remove the radix tree for MAC addresses per QP, as it's not in use.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to having more than one unicast MAC per port, we need to keep track
of the previous MAC address in the flow of ndo_set_mac_address,
so that mlx4_en_replace_mac will know what to replace.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, mlx4_en_do_set_multicast serves as the ndo_set_rx_mode entry for mlx4_en,
doing all related work. Split it to few calls, one per required functionality
(e.g multicast, promiscuous, etc) and rename some structures and calls
to use rx_mode notation instead of multicast.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.

Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp

To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the code consistent in regard to error messages
not spanning multiple lines.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, RX path code that does RX filtering is not optimized
and does an expensive conversion. In order to use ether_addr_equal_64bits
which is optimized for such cases, we need the MAC address kept by the device
to be in the form of unsigned char array instead of u64. Store the MAC address
as unsigned char array and convert to/from u64 out of the fast path when needed.
Side effect of this is that we no longer need priv->mac, since it's the same
as dev->dev_addr.

This optimization was suggested by Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently there are relatively complex conditional checks in the fast path,
for TX loopback enabling and resulting RX filter logic.
Move elaborate if's out of data path, replace them with a single flag
for each state and update that state from appropriate places.
Also, in native (non SRIOV) mode and not in loopback or in selftest,
there is no need to try and filter out packets that HW loopback-ed,
as in native mode we do not loopback packets anymore.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to e1000e and ixgbe.  Majority of the patches
are against e1000e, where Bruce makes several cosmetic #define moves into
header files.  In addition, Bruce does a cleanup of braces to resolve
checkpatch warnings (when using the strict option).

Ixgbe patches contain several fixes as well as updating the copyright.  The
fixes from Josh Hay, resolved a possible NULL pointer dereference and
resolved Smatch warnings by fixing return values and memcpy parameters.
Alex provides 2 fixes, the first is to replace rmb() with
read_barrier_depends() in the Tx cleanup.  The second fixes an MTU
warning when using SR-IOV which corrects the fact that we were using 1522
to test for the max frame size in ixgbe_change_mtu and 1518 in
ixgbe_set_vf_lpe.  The difference was the addition of VLAN_HLEN, which we
only need to add in the case of computing a buffer size, but not a filter
size.  Lastly, a patch from Emil which is based on a community patch from
Aurélien Guillaume which adds functions needed for reading SFF-8472
diagnostic data from SFP modules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP Appropriate Byte Count was added by me, but later disabled.
There is no point in maintaining it since it is a potential source
of bugs and Linux already implements other better window protection
heuristics.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

All in-tree ipv4 protocol implementations are now namespace
aware.  Therefore all the run-time checks are superfluous.

Reject registry of any non-namespace aware ipv4 protocol.
Eventually we'll remove prot->netns_ok and this registry
time check as well.
Signed-off-by: David S. Miller <davem@davemloft.net>

The infrastructure is already pretty much entirely there
to allow this conversion.

The tunnel and session lookups have per-namespace tables,
and the ipv4 bind lookup includes the namespace in the
lookup key.

Set netns_ok in l2tp_ip_protocol.
Signed-off-by: David S. Miller <davem@davemloft.net>

When creating unmanaged tunnel sockets we should honour the network namespace
passed to l2tp_tunnel_create.  Furthermore, unmanaged tunnel sockets should
not hold a reference to the network namespace lest they accidentally keep
alive a namespace which should otherwise have been released.

Unmanaged tunnel sockets now drop their namespace reference via sk_change_net,
and are released in a new pernet exit callback, l2tp_exit_net.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp_tunnel_create is passed a pointer to the network namespace for the
tunnel, along with an optional file descriptor for the tunnel which may
be passed in from userspace via. netlink.

In the case where the file descriptor is defined, ensure that the namespace
associated with that socket matches the namespace explicitly passed to
l2tp_tunnel_create.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The L2TP netlink code can run in namespaces.  Set the netnsok flag in
genl_family to true to reflect that fact.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To allow l2tp_tunnel_delete to be called from an atomic context, place the
tunnel socket release calls on a workqueue for asynchronous execution.

Tunnel memory is eventually freed in the tunnel socket destructor.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/intel/e1000e/ethtool.c
	drivers/net/vmxnet3/vmxnet3_drv.c
	drivers/net/wireless/iwlwifi/dvm/tx.c
	net/ipv6/route.c

The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.

The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.

The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.

The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>

This change corrects the fact that we were using 1522 to test for the
max frame size in ixgbe_change_mtu and 1518 in ixgbe_set_vf_lpe.  The
difference was the addition of VLAN_HLEN which we only need to add in the case
of computing a buffer size, but not a filter size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the rval variable returns from function and replaces
them with direct returns in ixgbe_dcbnl_getnumtcs. It also changes how
ixgbe_gstrings_test is copied into data with memcpy in ixgbe_get_strings
because "*ixgbe_gstrings_test too small (32 vs 160)".
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a default case which goes to the next loop iteration
in the case where p is not set, preventing p from being dereferenced.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.

Based on original patch from Aurélien Guillaume <footplus@gmail.com>

CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines, function prototypes and data types which are applicable to
all/most devices supported by the driver but are specific to the
manageability component of each device to the new manage.h header file.
These #defines, function prototypes and data types can be used by other
files in the driver and moving them to the manageability-specific file
makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the NVM component of
each device to the new nvm.h header file.  These #defines and function
prototypes can be used by other files in the driver and moving them to the
NVM-specific file makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the PHY component of
each device to the new phy.h header file.  These function prototypes can be
used by other files in the driver and moving them to the PHY-specific file
makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move prototypes for functions which are applicable to all/most devices
supported by the driver and are specific to the MAC component of each
device to the new mac.h header file.  These function prototypes can be used
by other files in the driver and moving them to the MAC-specific file makes
it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names).  These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines specific to the ESB2/82563 family of devices to the new
80003es2lan.h header file.  These defines can be used by other files in the
driver and moving them to the 80003es2lan-family-specific file makes it
clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names).  These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We recently refactored the driver source, this patch will take care of
updating copyright date and adding it to newly added files.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ee873fda

    "gianfar: Pack struct gfar_priv_grp into three cachelines"

causes the following null dereference at driver init on sbc8548:

   libphy: Freescale PowerQUICC MII Bus: probed
   Unable to handle kernel paging request for data at address 0x00000000
   Faulting instruction address: 0xc01d6a38
   Oops: Kernel access of bad area, sig: 11 [#1]
   [...]
   NIP [c01d6a38] gfar_parse_group+0x228/0x280
   LR [c01d6a34] gfar_parse_group+0x224/0x280
   Call Trace:
   [ef82dd60] [c01d6a34] gfar_parse_group+0x224/0x280 (unreliable)
   [ef82dd90] [c01d73a4] gfar_probe+0x284/0xfe0

The reason is that the commit also changed the allocation of the
Rx and error handling irq structs to be skipped for !MQ_MG_MODE.
In the !MQ_MG_MODE case, only the Tx irq struct is allocated.

Digging further, we see that MQ_MG_MODE is set only if we find
the OF compatible string "fsl,etsec2".

A quick grep in the dts directory shows lots of boards that support
Rx/Tx/Err, but without this specific compat string.  And hence they
go after the unallocated Rx/Error structs and cause the above oops.

Hence such a change can not be deployed until all the dts files
are updated and sufficiently deployed.  Further, the optimization
is of limited value, since the kmalloc'd struct in question has only
a single unsigned int, and an (IFNAMSIZ + 6) sized string.

Note that no changes to the freeing code are needed here, as it
already did an unconditional free of Rx/Tx/Error gfar_irqinfo.

Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This module is namespace aware, netns_ok was just disabled by default
for sanity.
Signed-off-by: David S. Miller <davem@davemloft.net>

BUG: spinlock bad magic on CPU#1, swapper/0/1
lock: 0xbfae0f8c, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Backtrace:
 [<80011d54>] (dump_backtrace+0x0/0x10c) from [<804e7800>] (dump_stack+0x18/0x1c)
 r6:bfae0000 r5:bfae0f8c r4:00000000 r3:806c1310
 [<804e77e8>] (dump_stack+0x0/0x1c) from [<804e9f20>] (spin_dump+0x80/0x94)
 [<804e9ea0>] (spin_dump+0x0/0x94) from [<804e9f60>] (spin_bug+0x2c/0x30)
 r5:805f6f8c r4:bfae0f8c
 [<804e9f34>] (spin_bug+0x0/0x30) from [<80257984>] (do_raw_spin_lock+0x170/0x1b0                                         )
 r5:806b4950 r4:bfae0f8c
 [<80257814>] (do_raw_spin_lock+0x0/0x1b0) from [<804ed15c>] (_raw_spin_lock_irqs                                         ave+0x18/0x20)
 [<804ed144>] (_raw_spin_lock_irqsave+0x0/0x20) from [<8033c694>] (fec_ptp_start_                                         cyclecounter+0x3c/0x120)
 r4:bfae0f8c r3:00000002
 [<8033c658>] (fec_ptp_start_cyclecounter+0x0/0x120) from [<80339e08>] (fec_resta                                         rt+0x56c/0x5f8)
 r8:00000000 r7:806e6f48 r6:00000112 r5:806b4950 r4:bfae0000
 [<8033989c>] (fec_restart+0x0/0x5f8) from [<8033b9e4>] (fec_probe+0x508/0xa48)
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case port is leaving the team, set the option "activeport" as changed
so the change can be properly propagated to userspace
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

In team_port_del(), there is need to be do all the cleanup related
things first and netlink event notifiers should be called after that.
This fixes two problems:
team carrier is now correctly set (port is removed from list first)
mode can set option as changed in .port_leave op
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Essentially do the same thing with port list as with option list.
Multipart netlink message.
Side effect is that port event message can send port which is not longer
in team->port_list.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_eth_mc_map function can't be used when CONFIG_INET isn't defined.
Fixed compilation error by adding CONFIG_INET define check before using the
function.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>