- 20 Feb, 2015 40 commits
-
-
James P Michels III authored
commit cd83ce9e upstream. This patch adds a usb quirk to support devices with interupt endpoints and bInterval values expressed as microframes. The quirk causes the parse endpoint function to modify the reported bInterval to a standards conforming value. There is currently code in the endpoint parser that checks for bIntervals that are outside of the valid range (1-16 for USB 2+ high speed and super speed interupt endpoints). In this case, the code assumes the bInterval is being reported in 1ms frames. As well, the correction is only applied if the original bInterval value is out of the 1-16 range. With this quirk applied to the device, the bInterval will be accurately adjusted from microframes to an exponent. Signed-off-by: James P Michels III <james.p.michels@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Dmitry Nezhevenko authored
commit bf5c4136 upstream. It looks like FUA support is broken on JMicron 152d:2566 bridge: [223159.885704] sd 7:0:0:0: [sdc] Write Protect is off [223159.885706] sd 7:0:0:0: [sdc] Mode Sense: 47 00 10 08 [223159.885942] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA [223283.691677] sd 7:0:0:0: [sdc] [223283.691680] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [223283.691681] sd 7:0:0:0: [sdc] [223283.691682] Sense Key : Illegal Request [current] [223283.691684] sd 7:0:0:0: [sdc] [223283.691685] Add. Sense: Invalid field in cdb [223283.691686] sd 7:0:0:0: [sdc] CDB: [223283.691687] Write(10): 2a 08 15 d0 83 0d 00 00 01 00 [223283.691690] blk_update_request: critical target error, dev sdc, sector 2927892584 This patch adds blacklist flag so that sd will not use FUA Signed-off-by: Dmitry Nezhevenko <dion@dion.org.ua> Cc: Phil Dibowitz <phil@ipom.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johannes Berg authored
commit 0fa7b391 upstream. In case userspace attempts to obtain key information for or delete a unicast key, this is currently erroneously rejected unless the driver sets the WIPHY_FLAG_IBSS_RSN flag. Apparently enough drivers do so it was never noticed. Fix that, and while at it fix a potential memory leak: the error path in the get_key() function was placed after allocating a message but didn't free it - move it to a better place. Luckily admin permissions are needed to call this operation. Fixes: e31b8213 ("cfg80211/mac80211: allow per-station GTKs") Signed-off-by: Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Andy Lutomirski authored
commit 3669ef9f upstream. The Witcher 2 did something like this to allocate a TLS segment index: struct user_desc u_info; bzero(&u_info, sizeof(u_info)); u_info.entry_number = (uint32_t)-1; syscall(SYS_set_thread_area, &u_info); Strictly speaking, this code was never correct. It should have set read_exec_only and seg_not_present to 1 to indicate that it wanted to find a free slot without putting anything there, or it should have put something sensible in the TLS slot if it wanted to allocate a TLS entry for real. The actual effect of this code was to allocate a bogus segment that could be used to exploit espfix. The set_thread_area hardening patches changed the behavior, causing set_thread_area to return -EINVAL and crashing the game. This changes set_thread_area to interpret this as a request to find a free slot and to leave it empty, which isn't *quite* what the game expects but should be close enough to keep it working. In particular, using the code above to allocate two segments will allocate the same segment both times. According to FrostbittenKing on Github, this fixes The Witcher 2. If this somehow still causes problems, we could instead allocate a limit==0 32-bit data segment, but that seems rather ugly to me. Fixes: 41bdc785 x86/tls: Validate TLS entries to protect espfix Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: torvalds@linux-foundation.org Link: http://lkml.kernel.org/r/0cb251abe1ff0958b8e468a9a9a905b80ae3a746.1421954363.git.luto@amacapital.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Jochen Hein authored
commit 1d90d6d5 upstream. Without this the aux port does not get detected, and consequently the touchpad will not work. With this patch the touchpad is detected: $ dmesg | grep -E "(SYN|i8042|serio)" pnp 00:03: Plug and Play ACPI device, IDs SYN1d22 PNP0f13 (active) i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126800, board id: 2863, fw id: 1473085 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 dmidecode excerpt for this laptop is: Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Medion Product Name: Akoya E7225 Version: 1.0 Signed-off-by: Jochen Hein <jochen@jochen.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Andy Lutomirski authored
commit e30ab185 upstream. 32-bit programs don't have an lm bit in their ABI, so they can't reliably cause LDT_empty to return true without resorting to memset. They shouldn't need to do this. This should fix a longstanding, if minor, issue in all 64-bit kernels as well as a potential regression in the TLS hardening code. Fixes: 41bdc785 x86/tls: Validate TLS entries to protect espfix Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: torvalds@linux-foundation.org Link: http://lkml.kernel.org/r/72a059de55e86ad5e2935c80aa91880ddf19d07c.1421954363.git.luto@amacapital.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
K. Y. Srinivasan authored
commit 32c6590d upstream. The Hyper-V clocksource is continuous; mark it accordingly. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Acked-by: jasowang@redhat.com Cc: gregkh@linuxfoundation.org Cc: devel@linuxdriverproject.org Cc: olaf@aepfle.de Cc: apw@canonical.com Link: http://lkml.kernel.org/r/1421108762-3331-1-git-send-email-kys@microsoft.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
David Jeffery authored
commit ce751452 upstream. It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG(). This problem is hard to reproduce making this patch hard to verify, but this fix will prevent the race. I have not been able to reproduce the problem, but here is a crash dump from a 2.6.32 kernel. On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE: crash> struct ata_port.hsm_task_state ffff881c1121c000 hsm_task_state = 0 Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(), which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value. PID: 11053 TASK: ffff8816e846cae0 CPU: 0 COMMAND: "sshd" #0 [ffff88008ba03960] machine_kexec at ffffffff81038f3b #1 [ffff88008ba039c0] crash_kexec at ffffffff810c5d92 #2 [ffff88008ba03a90] oops_end at ffffffff8152b510 #3 [ffff88008ba03ac0] die at ffffffff81010e0b #4 [ffff88008ba03af0] do_trap at ffffffff8152ad74 #5 [ffff88008ba03b50] do_invalid_op at ffffffff8100cf95 #6 [ffff88008ba03bf0] invalid_op at ffffffff8100bf9b [exception RIP: ata_sff_hsm_move+317] RIP: ffffffff813a77ad RSP: ffff88008ba03ca0 RFLAGS: 00010097 RAX: 0000000000000000 RBX: ffff881c1121dc60 RCX: 0000000000000000 RDX: ffff881c1121dd10 RSI: ffff881c1121dc60 RDI: ffff881c1121c000 RBP: ffff88008ba03d00 R8: 0000000000000000 R9: 000000000000002e R10: 000000000001003f R11: 000000000000009b R12: ffff881c1121c000 R13: 0000000000000000 R14: 0000000000000050 R15: ffff881c1121dd78 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #7 [ffff88008ba03d08] ata_sff_host_intr at ffffffff813a7fbd #8 [ffff88008ba03d38] ata_sff_interrupt at ffffffff813a821e #9 [ffff88008ba03d78] handle_IRQ_event at ffffffff810e6ec0 >--- <IRQ stack> --- [exception RIP: pipe_poll+48] RIP: ffffffff81192780 RSP: ffff880f26d459b8 RFLAGS: 00000246 RAX: 0000000000000000 RBX: ffff880f26d459c8 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff881a0539fa80 RBP: ffffffff8100bb8e R8: ffff8803b23324a0 R9: 0000000000000000 R10: ffff880f26d45dd0 R11: 0000000000000008 R12: ffffffff8109b646 R13: ffff880f26d45948 R14: 0000000000000246 R15: 0000000000000246 ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018 RIP: 00007f26017435c3 RSP: 00007fffe020c420 RFLAGS: 00000206 RAX: 0000000000000017 RBX: ffffffff8100b072 RCX: 00007fffe020c45c RDX: 00007f2604a3f120 RSI: 00007f2604a3f140 RDI: 000000000000000d RBP: 0000000000000000 R8: 00007fffe020e570 R9: 0101010101010101 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffe020e5f0 R13: 00007fffe020e5f4 R14: 00007f26045f373c R15: 00007fffe020e5e0 ORIG_RAX: 0000000000000017 CS: 0033 SS: 002b Somewhere between the ata_sff_hsm_move() check and the ata_sff_host_intr() check, the value changed. On examining the other cpus to see what else was running, another cpu was running the error handler routines: PID: 326 TASK: ffff881c11014aa0 CPU: 1 COMMAND: "scsi_eh_1" #0 [ffff88008ba27e90] crash_nmi_callback at ffffffff8102fee6 #1 [ffff88008ba27ea0] notifier_call_chain at ffffffff8152d515 #2 [ffff88008ba27ee0] atomic_notifier_call_chain at ffffffff8152d57a #3 [ffff88008ba27ef0] notify_die at ffffffff810a154e #4 [ffff88008ba27f20] do_nmi at ffffffff8152b1db #5 [ffff88008ba27f50] nmi at ffffffff8152aaa0 [exception RIP: _spin_lock_irqsave+47] RIP: ffffffff8152a1ff RSP: ffff881c11a73aa0 RFLAGS: 00000006 RAX: 0000000000000001 RBX: ffff881c1121deb8 RCX: 0000000000000000 RDX: 0000000000000246 RSI: 0000000000000020 RDI: ffff881c122612d8 RBP: ffff881c11a73aa0 R8: ffff881c17083800 R9: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff881c1121c000 R13: 000000000000001f R14: ffff881c1121dd50 R15: ffff881c1121dc60 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000 >--- <NMI exception stack> --- #6 [ffff881c11a73aa0] _spin_lock_irqsave at ffffffff8152a1ff #7 [ffff881c11a73aa8] ata_exec_internal_sg at ffffffff81396fb5 #8 [ffff881c11a73b58] ata_exec_internal at ffffffff81397109 #9 [ffff881c11a73bd8] atapi_eh_request_sense at ffffffff813a34eb Before it tried to acquire a spinlock, ata_exec_internal_sg() called ata_sff_flush_pio_task(). This function will set ap->hsm_task_state to HSM_ST_IDLE, and has no locking around setting this value. ata_sff_flush_pio_task() can then race with the interrupt handler and potentially set HSM_ST_IDLE at a fatal moment, which will trigger a kernel BUG. v2: Fixup comment in ata_sff_flush_pio_task() tj: Further updated comment. Use ap->lock instead of shost lock and use the [un]lock_irq variant instead of the irqsave/restore one. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Michael Karcher authored
commit 1caf6aaa upstream. Compiling SH with gcc-4.8 fails due to the -m32 option not being supported. From http://buildd.debian-ports.org/status/fetch.php?pkg=linux&arch=sh4&ver=3.16.7-ckt4-1&stamp=1421425783 CC init/main.o gcc-4.8: error: unrecognized command line option '-m32' ld: cannot find init/.tmp_mc_main.o: No such file or directory objcopy: 'init/.tmp_mx_main.o': No such file rm: cannot remove 'init/.tmp_mx_main.o': No such file or directory rm: cannot remove 'init/.tmp_mc_main.o': No such file or directory Link: http://lkml.kernel.org/r/1421537778-29001-1-git-send-email-kernel@mkarcher.dialup.fu-berlin.de Link: http://lkml.kernel.org/r/54BCBDD4.10102@physik.fu-berlin.de Cc: Matt Fleming <matt@console-pimps.org> Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Dan Williams authored
commit 72dd299d upstream. Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101 "Since commit 8a4aeec8 "libata/ahci: accommodate tag ordered controllers" the access to the harddisk on the first SATA-port is failing on its first access. The access to the harddisk on the second port is working normal. When reverting the above commit, access to both harddisks is working fine again." Maintain tag ordered submission as the default, but allow sata_sil24 to continue with the old behavior. Cc: Tejun Heo <tj@kernel.org> Reported-by: Ronny Hegewald <Ronny.Hegewald@online.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Jason Lee Cragg authored
commit 64559311 upstream. Signed-off-by: Jason Lee Cragg <jcragg@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Daniel Borkmann authored
commit 2061dcd6 upstream. I.e. one-to-many sockets in SCTP are not required to explicitly call into connect(2) or sctp_connectx(2) prior to data exchange. Instead, they can directly invoke sendmsg(2) and the SCTP stack will automatically trigger connection establishment through 4WHS via sctp_primitive_ASSOCIATE(). However, this in its current implementation is racy: INIT is being sent out immediately (as it cannot be bundled anyway) and the rest of the DATA chunks are queued up for later xmit when connection is established, meaning sendmsg(2) will return successfully. This behaviour can result in an undesired side-effect that the kernel made the application think the data has already been transmitted, although none of it has actually left the machine, worst case even after close(2)'ing the socket. Instead, when the association from client side has been shut down e.g. first gracefully through SCTP_EOF and then close(2), the client could afterwards still receive the server's INIT_ACK due to a connection with higher latency. This INIT_ACK is then considered out of the blue and hence responded with ABORT as there was no alive assoc found anymore. This can be easily reproduced f.e. with sctp_test application from lksctp. One way to fix this race is to wait for the handshake to actually complete. The fix defers waiting after sctp_primitive_ASSOCIATE() and sctp_primitive_SEND() succeeded, so that DATA chunks cooked up from sctp_sendmsg() have already been placed into the output queue through the side-effect interpreter, and therefore can then be bundeled together with COOKIE_ECHO control chunks. strace from example application (shortened): socket(PF_INET, SOCK_SEQPACKET, IPPROTO_SCTP) = 3 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(0)=[], msg_controllen=48, {cmsg_len=48, cmsg_level=0x84 /* SOL_??? */, cmsg_type=, ...}, msg_flags=0}, 0) = 0 // graceful shutdown for SOCK_SEQPACKET via SCTP_EOF close(3) = 0 tcpdump before patch (fooling the application): 22:33:36.306142 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 3879023686] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3139201684] 22:33:36.316619 IP 192.168.1.115.8888 > 192.168.1.114.41462: sctp (1) [INIT ACK] [init tag: 3345394793] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 3380109591] 22:33:36.317600 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [ABORT] tcpdump after patch: 14:28:58.884116 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 438593213] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3092969729] 14:28:58.888414 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [INIT ACK] [init tag: 381429855] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 2141904492] 14:28:58.888638 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [COOKIE ECHO] , (2) [DATA] (B)(E) [TSN: 3092969729] [...] 14:28:58.893278 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [COOKIE ACK] , (2) [SACK] [cum ack 3092969729] [a_rwnd 106491] [#gap acks 0] [#dup tsns 0] 14:28:58.893591 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969730] [...] 14:28:59.096963 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969730] [a_rwnd 106496] [#gap acks 0] [#dup tsns 0] 14:28:59.097086 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969731] [...] , (2) [DATA] (B)(E) [TSN: 3092969732] [...] 14:28:59.103218 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969732] [a_rwnd 106486] [#gap acks 0] [#dup tsns 0] 14:28:59.103330 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN] 14:28:59.107793 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SHUTDOWN ACK] 14:28:59.107890 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN COMPLETE] Looks like this bug is from the pre-git history museum. ;) Fixes: 08707d54 ("lksctp-2_5_31-0_5_1.patch") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johan Hovold authored
commit ebbeba12 upstream. Fix attribute-creation race with userspace by using the default group to create also the contingent gpio device attributes. Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [bwh: Backported to 3.2: - Adjust filenames, context - Use gpio_to_desc(), not gpiod_to_desc(), in gpio_is_visible() - gpio_is_visible() must return mode_t] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johan Hovold authored
commit 0915e6fe upstream. The gpio device attributes were never destroyed when the gpio was unexported (or on export failures). Use device_create_with_groups() to create the default device attributes of the gpio class device. Note that this also fixes the attribute-creation race with userspace for these attributes. Remove contingent attributes in export error path and on unexport. Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Ming Lei authored
commit 864533ce upstream. Hi, On Wed, Feb 8, 2012 at 8:41 PM, Felipe Balbi <balbi@ti.com> wrote: > Hi guys, > > I have just triggered the folllowing: > > [ 84.860321] ====================================================== > [ 84.860321] [ INFO: possible circular locking dependency detected ] > [ 84.860321] 3.3.0-rc2-00026-ge4e8a39 #474 Not tainted > [ 84.860321] ------------------------------------------------------- > [ 84.860321] bash/949 is trying to acquire lock: > [ 84.860321] (sysfs_lock){+.+.+.}, at: [<c0275358>] gpio_value_store+0x24/0xcc > [ 84.860321] > [ 84.860321] but task is already holding lock: > [ 84.860321] (s_active#22){++++.+}, at: [<c016996c>] sysfs_write_file+0xdc/0x184 > [ 84.911468] > [ 84.911468] which lock already depends on the new lock. > [ 84.911468] > [ 84.920043] > [ 84.920043] the existing dependency chain (in reverse order) is: > [ 84.920043] > [ 84.927886] -> #1 (s_active#22){++++.+}: > [ 84.927886] [<c008f640>] check_prevs_add+0xdc/0x150 > [ 84.927886] [<c008fc18>] validate_chain.clone.24+0x564/0x694 > [ 84.927886] [<c0090cdc>] __lock_acquire+0x49c/0x980 > [ 84.951660] [<c0091838>] lock_acquire+0x98/0x100 > [ 84.951660] [<c016a8e8>] sysfs_deactivate+0xb0/0x100 > [ 84.962982] [<c016b1b4>] sysfs_addrm_finish+0x2c/0x6c > [ 84.962982] [<c016b8bc>] sysfs_remove_dir+0x84/0x98 > [ 84.962982] [<c02590d8>] kobject_del+0x10/0x78 > [ 84.974670] [<c02c29e8>] device_del+0x140/0x170 > [ 84.974670] [<c02c2a24>] device_unregister+0xc/0x18 > [ 84.985382] [<c0276894>] gpio_unexport+0xbc/0xdc > [ 84.985382] [<c02768c8>] gpio_free+0x14/0xfc > [ 85.001708] [<c0276a28>] unexport_store+0x78/0x8c > [ 85.001708] [<c02c5af8>] class_attr_store+0x18/0x24 > [ 85.007293] [<c0169990>] sysfs_write_file+0x100/0x184 > [ 85.018981] [<c0109d48>] vfs_write+0xb4/0x148 > [ 85.018981] [<c0109fd0>] sys_write+0x40/0x70 > [ 85.018981] [<c0013cc0>] ret_fast_syscall+0x0/0x3c > [ 85.035003] > [ 85.035003] -> #0 (sysfs_lock){+.+.+.}: > [ 85.035003] [<c008f54c>] check_prev_add+0x680/0x698 > [ 85.035003] [<c008f640>] check_prevs_add+0xdc/0x150 > [ 85.052093] [<c008fc18>] validate_chain.clone.24+0x564/0x694 > [ 85.052093] [<c0090cdc>] __lock_acquire+0x49c/0x980 > [ 85.052093] [<c0091838>] lock_acquire+0x98/0x100 > [ 85.069885] [<c047e280>] mutex_lock_nested+0x3c/0x2f4 > [ 85.069885] [<c0275358>] gpio_value_store+0x24/0xcc > [ 85.069885] [<c02c18dc>] dev_attr_store+0x18/0x24 > [ 85.087158] [<c0169990>] sysfs_write_file+0x100/0x184 > [ 85.087158] [<c0109d48>] vfs_write+0xb4/0x148 > [ 85.098297] [<c0109fd0>] sys_write+0x40/0x70 > [ 85.098297] [<c0013cc0>] ret_fast_syscall+0x0/0x3c > [ 85.109069] > [ 85.109069] other info that might help us debug this: > [ 85.109069] > [ 85.117462] Possible unsafe locking scenario: > [ 85.117462] > [ 85.117462] CPU0 CPU1 > [ 85.128417] ---- ---- > [ 85.128417] lock(s_active#22); > [ 85.128417] lock(sysfs_lock); > [ 85.128417] lock(s_active#22); > [ 85.142486] lock(sysfs_lock); > [ 85.151794] > [ 85.151794] *** DEADLOCK *** > [ 85.151794] > [ 85.151794] 2 locks held by bash/949: > [ 85.158020] #0: (&buffer->mutex){+.+.+.}, at: [<c01698b8>] sysfs_write_file+0x28/0x184 > [ 85.170349] #1: (s_active#22){++++.+}, at: [<c016996c>] sysfs_write_file+0xdc/0x184 > [ 85.170349] > [ 85.178588] stack backtrace: > [ 85.178588] [<c001b824>] (unwind_backtrace+0x0/0xf0) from [<c008de64>] (print_circular_bug+0x100/0x114) > [ 85.193023] [<c008de64>] (print_circular_bug+0x100/0x114) from [<c008f54c>] (check_prev_add+0x680/0x698) > [ 85.193023] [<c008f54c>] (check_prev_add+0x680/0x698) from [<c008f640>] (check_prevs_add+0xdc/0x150) > [ 85.212524] [<c008f640>] (check_prevs_add+0xdc/0x150) from [<c008fc18>] (validate_chain.clone.24+0x564/0x694) > [ 85.212524] [<c008fc18>] (validate_chain.clone.24+0x564/0x694) from [<c0090cdc>] (__lock_acquire+0x49c/0x980) > [ 85.233306] [<c0090cdc>] (__lock_acquire+0x49c/0x980) from [<c0091838>] (lock_acquire+0x98/0x100) > [ 85.233306] [<c0091838>] (lock_acquire+0x98/0x100) from [<c047e280>] (mutex_lock_nested+0x3c/0x2f4) > [ 85.242614] [<c047e280>] (mutex_lock_nested+0x3c/0x2f4) from [<c0275358>] (gpio_value_store+0x24/0xcc) > [ 85.261840] [<c0275358>] (gpio_value_store+0x24/0xcc) from [<c02c18dc>] (dev_attr_store+0x18/0x24) > [ 85.261840] [<c02c18dc>] (dev_attr_store+0x18/0x24) from [<c0169990>] (sysfs_write_file+0x100/0x184) > [ 85.271240] [<c0169990>] (sysfs_write_file+0x100/0x184) from [<c0109d48>] (vfs_write+0xb4/0x148) > [ 85.290008] [<c0109d48>] (vfs_write+0xb4/0x148) from [<c0109fd0>] (sys_write+0x40/0x70) > [ 85.298400] [<c0109fd0>] (sys_write+0x40/0x70) from [<c0013cc0>] (ret_fast_syscall+0x0/0x3c) > -bash: echo: write error: Operation not permitted > > the way to trigger is: > > root@legolas:~# cd /sys/class/gpio/ > root@legolas:/sys/class/gpio# echo 2 > export > root@legolas:/sys/class/gpio# echo 2 > unexport > root@legolas:/sys/class/gpio# echo 2 > export > root@legolas:/sys/class/gpio# cd gpio2/ > root@legolas:/sys/class/gpio/gpio2# echo 1 > value Looks 'sysfs_lock' needn't to be held for unregister, so the patch below may fix the problem. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Ryan Mallon authored
commit fc4e2514 upstream. The gpio_export function uses nested if statements and the status variable to handle the failure cases. This makes the function logic difficult to follow. Refactor the code to abort immediately on failure using goto. This makes the code slightly longer, but significantly reduces the nesting and number of split lines and makes the code easier to read. Signed-off-by: Ryan Mallon <rmallon@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johan Hovold authored
commit 121b6a79 upstream. The gpio-chip device attributes were never destroyed when the device was removed. Fix by using device_create_with_groups() to create the device attributes of the chip class device. Note that this also fixes the attribute-creation race with userspace. Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Guenter Roeck authored
commit 39ef3112 upstream. device_create_groups lets callers create devices as well as associated sysfs attributes with a single call. This avoids race conditions seen if sysfs attributes on new devices are created later. [fixed up comment block placement and add checks for printk buffer formats - gregkh] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Greg Kroah-Hartman authored
commit f2f37f58 upstream. To make it easier for driver subsystems to work with attribute groups, create the ATTRIBUTE_GROUPS macro to remove some of the repetitive typing for the most common use for attribute groups. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Oliver Hartkopp authored
commit 9b1087aa upstream. When changing flags in the CAN drivers ctrlmode the provided new content has to be checked whether the bits are allowed to be changed. The bits that are to be changed are given as a bitfield in cm->mask. Therefore checking against cm->flags is wrong as the content can hold any kind of values. The iproute2 tool sets the bits in cm->mask and cm->flags depending on the detected command line options. To be robust against bogus user space applications additionally sanitize the provided flags with the provided mask. Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Steven Rostedt (Red Hat) authored
commit 237d28db upstream. If the function graph tracer traces a jprobe callback, the system will crash. This can easily be demonstrated by compiling the jprobe sample module that is in the kernel tree, loading it and running the function graph tracer. # modprobe jprobe_example.ko # echo function_graph > /sys/kernel/debug/tracing/current_tracer # ls The first two commands end up in a nice crash after the first fork. (do_fork has a jprobe attached to it, so "ls" just triggers that fork) The problem is caused by the jprobe_return() that all jprobe callbacks must end with. The way jprobes works is that the function a jprobe is attached to has a breakpoint placed at the start of it (or it uses ftrace if fentry is supported). The breakpoint handler (or ftrace callback) will copy the stack frame and change the ip address to return to the jprobe handler instead of the function. The jprobe handler must end with jprobe_return() which swaps the stack and does an int3 (breakpoint). This breakpoint handler will then put back the saved stack frame, simulate the instruction at the beginning of the function it added a breakpoint to, and then continue on. For function tracing to work, it hijakes the return address from the stack frame, and replaces it with a hook function that will trace the end of the call. This hook function will restore the return address of the function call. If the function tracer traces the jprobe handler, the hook function for that handler will not be called, and its saved return address will be used for the next function. This will result in a kernel crash. To solve this, pause function tracing before the jprobe handler is called and unpause it before it returns back to the function it probed. Some other updates: Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the code look a bit cleaner and easier to understand (various tries to fix this bug required this change). Note, if fentry is being used, jprobes will change the ip address before the function graph tracer runs and it will not be able to trace the function that the jprobe is probing. Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.orgAcked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> [bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johan Hovold authored
commit 5539b3c9 upstream. Memory allocated and references taken by of_gpiochip_add and acpi_gpiochip_add were never released on errors in gpiochip_add (e.g. failure to find free gpio range). Fixes: 391c970c ("of/gpio: add default of_xlate function if device has a node pointer") Fixes: 664e3e5a ("gpio / ACPI: register to ACPI events automatically") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [bwh: Backported to 3.2: - Move call to of_gpiochip_add() into conditional section rather than rearranging gotos and labels which are in different places here - There's no ACPI support] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Mathias Krause authored
commit 3e14dcf7 upstream. Commit 5d26a105 ("crypto: prefix module autoloading with "crypto-"") changed the automatic module loading when requesting crypto algorithms to prefix all module requests with "crypto-". This requires all crypto modules to have a crypto specific module alias even if their file name would otherwise match the requested crypto algorithm. Even though commit 5d26a105 added those aliases for a vast amount of modules, it was missing a few. Add the required MODULE_ALIAS_CRYPTO annotations to those files to make them get loaded automatically, again. This fixes, e.g., requesting 'ecb(blowfish-generic)', which used to work with kernels v3.18 and below. Also change MODULE_ALIAS() lines to MODULE_ALIAS_CRYPTO(). The former won't work for crypto modules any more. Fixes: 5d26a105 ("crypto: prefix module autoloading with "crypto-"") Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> [bwh: Backported to 3.2: - Adjust filenames - Drop changes to algorithms and drivers we don't have] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Kees Cook authored
commit 4943ba16 upstream. This adds the module loading prefix "crypto-" to the template lookup as well. For example, attempting to load 'vfat(blowfish)' via AF_ALG now correctly includes the "crypto-" prefix at every level, correctly rejecting "vfat": net-pf-38 algif-hash crypto-vfat(blowfish) crypto-vfat(blowfish)-all crypto-vfat Reported-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> [bwh: Backported to 3.2: drop changes to cmac and mcryptd which we don't have] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Kees Cook authored
commit 5d26a105 upstream. This prefixes all crypto module loading with "crypto-" so we never run the risk of exposing module auto-loading to userspace via a crypto API, as demonstrated by Mathias Krause: https://lkml.org/lkml/2013/3/4/70Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> [bwh: Backported to 3.2: - Adjust filenames - Drop changes to algorithms and drivers we don't have - Add aliases to generic C implementations that didn't need them before] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Konstantin Khlebnikov authored
commit b800c91a upstream. Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel BUG at mm/rmap.c:399!") caused by commit 7a3ef208 ("mm: prevent endless growth of anon_vma hierarchy") Anon_vma_clone() is usually called for a copy of source vma in destination argument. If source vma has anon_vma it should be already in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's called from anon_vma_fork(). In this case anon_vma_clone() finds anon_vma for reusing. Vma_adjust() calls it differently and this breaks anon_vma reusing logic: anon_vma_clone() links vma to old anon_vma and updates degree counters but vma_adjust() overrides vma->anon_vma right after that. As a result final unlink_anon_vmas() decrements degree for wrong anon_vma. This patch assigns ->anon_vma before calling anon_vma_clone(). Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com> Reported-and-tested-by: Oded Gabbay <oded.gabbay@amd.com> Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: vma_adjust() didn't use a variable to propagate the error code from anon_vma_clone(); change that at the same time] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Linus Torvalds authored
commit 690eac53 upstream. Commit fee7e49d ("mm: propagate error from stack expansion even for guard page") made sure that we return the error properly for stack growth conditions. It also theorized that counting the guard page towards the stack limit might break something, but also said "Let's see if anybody notices". Somebody did notice. Apparently android-x86 sets the stack limit very close to the limit indeed, and including the guard page in the rlimit check causes the android 'zygote' process problems. So this adds the (fairly trivial) code to make the stack rlimit check be against the actual real stack size, rather than the size of the vma that includes the guard page. Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org> Cc: Jay Foad <jay.foad@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johan Hovold authored
commit 32a4bf2e upstream. Use tty kref to release the fake tty in usb_console_setup to avoid use after free if the underlying serial driver has acquired a reference. Note that using the tty destructor release_one_tty requires some more state to be initialised. Fixes: 4a90f09b ("tty: usb-serial krefs") Signed-off-by: Johan Hovold <johan@kernel.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Songjun Wu authored
commit 5fb694f9 upstream. When unloading the module 'g_hid.ko', the urb request will be dequeued and the completion routine will be excuted. If there is no urb packet, the urb request will not be added to the endpoint queue and the completion routine pointer in urb request is NULL. Accessing to this NULL function pointer will cause the Oops issue reported below. Add the code to check if the urb request is in the endpoint queue or not. If the urb request is not in the endpoint queue, a negative error code will be returned. Here is the Oops log: Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = dedf0000 [00000000] *pgd=3ede5831, *pte=00000000, *ppte=00000000 Internal error: Oops: 80000007 [#1] ARM Modules linked in: g_hid(-) usb_f_hid libcomposite CPU: 0 PID: 923 Comm: rmmod Not tainted 3.18.0+ #2 Hardware name: Atmel SAMA5 (Device Tree) task: df6b1100 ti: dedf6000 task.ti: dedf6000 PC is at 0x0 LR is at usb_gadget_giveback_request+0xc/0x10 pc : [<00000000>] lr : [<c02ace88>] psr: 60000093 sp : dedf7eb0 ip : df572634 fp : 00000000 r10: 00000000 r9 : df52e210 r8 : 60000013 r7 : df6a9858 r6 : df52e210 r5 : df6a9858 r4 : df572600 r3 : 00000000 r2 : ffffff98 r1 : df572600 r0 : df6a9868 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 3edf0059 DAC: 00000015 Process rmmod (pid: 923, stack limit = 0xdedf6230) Stack: (0xdedf7eb0 to 0xdedf8000) 7ea0: 00000000 c02adbbc df572580 deced608 7ec0: df572600 df6a9868 df572634 c02aed3c df577c00 c01b8608 00000000 df6be27c 7ee0: 00200200 00100100 bf0162f4 c000e544 dedf6000 00000000 00000000 bf010c00 7f00: bf0162cc bf00159c 00000000 df572980 df52e218 00000001 df5729b8 bf0031d0 [..] [<c02ace88>] (usb_gadget_giveback_request) from [<c02adbbc>] (request_complete+0x64/0x88) [<c02adbbc>] (request_complete) from [<c02aed3c>] (usba_ep_dequeue+0x70/0x128) [<c02aed3c>] (usba_ep_dequeue) from [<bf010c00>] (hidg_unbind+0x50/0x7c [usb_f_hid]) [<bf010c00>] (hidg_unbind [usb_f_hid]) from [<bf00159c>] (remove_config.isra.6+0x98/0x9c [libcomposite]) [<bf00159c>] (remove_config.isra.6 [libcomposite]) from [<bf0031d0>] (__composite_unbind+0x34/0x98 [libcomposite]) [<bf0031d0>] (__composite_unbind [libcomposite]) from [<c02acee0>] (usb_gadget_remove_driver+0x50/0x78) [<c02acee0>] (usb_gadget_remove_driver) from [<c02ad570>] (usb_gadget_unregister_driver+0x64/0x94) [<c02ad570>] (usb_gadget_unregister_driver) from [<bf0160c0>] (hidg_cleanup+0x10/0x34 [g_hid]) [<bf0160c0>] (hidg_cleanup [g_hid]) from [<c0056748>] (SyS_delete_module+0x118/0x19c) [<c0056748>] (SyS_delete_module) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30) Code: bad PC value Signed-off-by: Songjun Wu <songjun.wu@atmel.com> [nicolas.ferre@atmel.com: reworked the commit message] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 914a3f3b ("USB: add atmel_usba_udc driver") Signed-off-by: Felipe Balbi <balbi@ti.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Bo Shen authored
commit 6785a103 upstream. When receive data, the RXRDY in status register set by hardware after a new packet has been stored in the endpoint FIFO. When it is copied from FIFO, this bit is cleared which make the FIFO can be accessed again. In the receive_data() function, this bit RXRDY has been cleared. So, after the receive_data() function return, this bit should not be cleared again, or else it may cause the accessing FIFO corrupt, which will make the data loss. Fixes: 914a3f3b (USB: add atmel_usba_udc driver) Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Bo Shen authored
commit f40afddd upstream. According to the datasheet, when transfer using DMA, the control setting for IN packet only need END_BUF_EN, END_BUF_IE, CH_EN, while for OUT packet, need more two bits END_TR_EN and END_TR_IE to be configured. Fixes: 914a3f3b (USB: add atmel_usba_udc driver) Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Arseny Solokha authored
commit 56abcab8 upstream. Commit 8dccddbc ("OHCI: final fix for NVIDIA problems (I hope)") introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development board. The code path that was previously specific to NVIDIA controllers had then become taken for all chips. However, the M5237 installed on the board wedges solid when accessing its base+OHCI_FMINTERVAL register, making it impossible to boot any kernel newer than 3.1.8 on this particular and apparently other similar machines. Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237. The patch is suitable for the -next tree as well as all maintained kernels up to 3.2 inclusive. Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Dan Carpenter authored
commit 606185b2 upstream. This is a static checker fix. We write some binary settings to the sysfs file. One of the settings is the "->startup_profile". There isn't any checking to make sure it fits into the pyra->profile_settings[] array in the profile_activated() function. I added a check to pyra_sysfs_write_settings() in both places because I wasn't positive that the other callers were correct. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> [bwh: Backported to 3.2: pyra_sysfs_write_settings() doesn't define a settings variable, so write the cast-expression inline] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Johannes Weiner authored
commit 2d6d7f98 upstream. Tejun, while reviewing the code, spotted the following race condition between the dirtying and truncation of a page: __set_page_dirty_nobuffers() __delete_from_page_cache() if (TestSetPageDirty(page)) page->mapping = NULL if (PageDirty()) dec_zone_page_state(page, NR_FILE_DIRTY); dec_bdi_stat(mapping->backing_dev_info, BDI_RECLAIMABLE); if (page->mapping) account_page_dirtied(page) __inc_zone_page_state(page, NR_FILE_DIRTY); __inc_bdi_stat(mapping->backing_dev_info, BDI_RECLAIMABLE); which results in an imbalance of NR_FILE_DIRTY and BDI_RECLAIMABLE. Dirtiers usually lock out truncation, either by holding the page lock directly, or in case of zap_pte_range(), by pinning the mapcount with the page table lock held. The notable exception to this rule, though, is do_wp_page(), for which this race exists. However, do_wp_page() already waits for a locked page to unlock before setting the dirty bit, in order to prevent a race where clear_page_dirty() misses the page bit in the presence of dirty ptes. Upgrade that wait to a fully locked set_page_dirty() to also cover the situation explained above. Afterwards, the code in set_page_dirty() dealing with a truncation race is no longer needed. Remove it. Reported-by: Tejun Heo <tj@kernel.org> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: - Adjust context - Use VM_BUG_ON() rather than VM_BUG_ON_PAGE()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Miklos Szeredi authored
commit ed6d7c8e upstream. There's only one caller of set_page_dirty_balance() and that will call it with page_mkwrite == 0. The page_mkwrite argument was unused since commit b827e496 "mm: close page_mkwrite races". Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Konstantin Khlebnikov authored
commit 7a3ef208 upstream. Constantly forking task causes unlimited grow of anon_vma chain. Each next child allocates new level of anon_vmas and links vma to all previous levels because pages might be inherited from any level. This patch adds heuristic which decides to reuse existing anon_vma instead of forking new one. It adds counter anon_vma->degree which counts linked vmas and directly descending anon_vmas and reuses anon_vma if counter is lower than two. As a result each anon_vma has either vma or at least two descending anon_vmas. In such trees half of nodes are leafs with alive vmas, thus count of anon_vmas is no more than two times bigger than count of vmas. This heuristic reuses anon_vmas as few as possible because each reuse adds false aliasing among vmas and rmap walker ought to scan more ptes when it searches where page is might be mapped. Link: http://lkml.kernel.org/r/20120816024610.GA5350@evergreen.ssec.wisc.edu Fixes: 5beb4930 ("mm: change anon_vma linking to fix multi-process server scalability issue") [akpm@linux-foundation.org: fix typo, per Rik] Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Reported-by: Daniel Forrest <dan.forrest@ssec.wisc.edu> Tested-by: Michal Hocko <mhocko@suse.cz> Tested-by: Jerome Marchand <jmarchan@redhat.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Reviewed-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Dmitry Torokhov authored
commit 9333caea upstream. When KBC is in active multiplexing mode the touchpad on this laptop does not work. Reported-by: Bilal Koc <koc.bilo@googlemail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Ashay Jaiswal authored
commit 83b0302d upstream. The regulator framework maintains a list of consumer regulators for a regulator device and protects it from concurrent access using the regulator device's mutex lock. In the case of regulator_put() the consumer is removed and regulator device's parameters are updated without holding the regulator device's mutex. This would lead to a race condition between the regulator_put() and any function which traverses the consumer list or modifies regulator device's parameters. Fix this race condition by holding the regulator device's mutex in case of regulator_put. Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org> Signed-off-by: Mark Brown <broonie@kernel.org> [bwh: Backported to 3.2: - Adjust context - Don't touch the comment; __regulator_put() has not been split out of regulator_put() here] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Srihari Vijayaraghavan authored
commit 148e9a71 upstream. On some laptops, keyboard needs to be reset in order to successfully detect touchpad (e.g., some Gigabyte laptop models with Elantech touchpads). Without resettin keyboard touchpad pretends to be completely dead. Based on the original patch by Mateusz Jończyk this version has been expanded to include DMI based detection & application of the fix automatically on the affected models of laptops. This has been confirmed to fix problem by three users already on three different models of laptops. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81331Signed-off-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com> Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Tested-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com> Tested by: Zakariya Dehlawi <zdehlawi@gmail.com> Tested-by: Guillaum Bouchard <guillaum.bouchard@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-
Sasha Levin authored
commit 6ada1fc0 upstream. An unvalidated user input is multiplied by a constant, which can result in an undefined behaviour for large values. While this is validated later, we should avoid triggering undefined behaviour. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> [jstultz: include trivial milisecond->microsecond correction noticed by Andy] Signed-off-by: John Stultz <john.stultz@linaro.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
-