Pull networking updates from David Miller:

 1) Platform regulatory domain support for ath10k, from Bartosz
    Markowski.

 2) Centralize min/max MTU checking, thus removing tons of duplicated
    code all of the the various drivers. From Jarod Wilson.

 3) Support ingress actions in act_mirred, from Shmulik Ladkani.

 4) Improve device adjacency tracking, from David Ahern.

 5) Add support for LED triggers on PHY link state changes, from Zach
    Brown.

 6) Improve UDP socket memory accounting, from Paolo Abeni.

 7) Set SK_MEM_QUANTUM to a fixed size of 4096, instead of PAGE_SIZE.
    From Eric Dumazet.

 8) Collapse TCP SKBs at retransmit time even if the right side SKB has
    frags. Also from Eric Dumazet.

 9) Add IP_RECVFRAGSIZE and IPV6_RECVFRAGSIZE cmsgs, from Willem de
    Bruijn.

10) Support routing by UID, from Lorenzo Colitti.

11) Handle L3 domain binding (ie. VRF) for RAW sockets, from David
    Ahern.

12) tcp_get_info() can run lockless, from Eric Dumazet.

13) 4-tuple UDP hashing in SFC driver, from Edward Cree.

14) Avoid reorders in GRO code, from Eric Dumazet.

15) IPV6 Segment Routing support, from David Lebrun.

16) Support MPLS push and pop for L3 packets in openvswitch, from Jiri
    Benc.

17) Add LRU datastructure support for BPF, Martin KaFai Lau.

18) VF support in liquidio driver, from Raghu Vatsavayi.

19) Multiqueue support in alx driver, from Tobias Regnery.

20) Networking cgroup BPF support, from Daniel Mack.

21) TCP chronograph measurements, from Francis Yan.

22) XDP support for qed driver, from Yuval Mintz.

23) BPF based lwtunnels, from Thomas Graf.

24) Consistent FIB dumping to offloading drivers, from Ido Schimmel.

25) Many optimizations for UDP under high load, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
  netfilter: nft_counter: rework atomic dump and reset
  e1000: use disable_hardirq() for e1000_netpoll()
  i40e: don't truncate match_method assignment
  net: ethernet: ti: netcp: add support of cpts
  net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause
  net: l2tp: ppp: change PPPOL2TP_MSG_* => L2TP_MSG_*
  net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*
  net: l2tp: export debug flags to UAPI
  net: ethernet: stmmac: remove private tx queue lock
  net: ethernet: sxgbe: remove private tx queue lock
  net: bridge: shorten ageing time on topology change
  net: bridge: add helper to set topology change
  net: bridge: add helper to offload ageing time
  net: nicvf: use new api ethtool_{get|set}_link_ksettings
  net: ethernet: ti: cpsw: sync rates for channels in dual emac mode
  net: ethernet: ti: cpsw: re-split res only when speed is changed
  net: ethernet: ti: cpsw: combine budget and weight split and check
  net: ethernet: ti: cpsw: don't start queue twice
  net: ethernet: ti: cpsw: use same macros to get active slave
  net: mvneta: select GENERIC_ALLOCATOR
  ...

Pull MIPS fixes from Ralf Baechle:
 "Two more MIPS fixes for 4.9:

   - RTC: Return -ENODEV so an external RTC will be tried

   - Fix mask of GPE frequency

  These two have been tested on Imagination's automated test system and
  also both received positive reviews on the linux-mips mailing list"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Lantiq: Fix mask of GPE frequency
  MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time

Dump and reset doesn't work unless cmpxchg64() is used both from packet
and control plane paths. This approach is going to be slow though.
Instead, use a percpu seqcount to fetch counters consistently, then
subtract bytes and packets in case a reset was requested.

The cpu that running over the reset code is guaranteed to own this stats
exclusively, we have to turn counters into signed 64bit though so stats
update on reset don't get wrong on underflow.

This patch is based on original sketch from Eric Dumazet.

Fixes: 43da04a5 ("netfilter: nf_tables: atomic dump and reset for stateful objects")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware documentation says bit 11:10 are used for the GPE
frequency selection. Fix the mask in the define to match these bits.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Langer <thomas.langer@intel.com>
Cc: linux-mips@linux-mips.org
Cc: john@phrozen.org
Patchwork: https://patchwork.linux-mips.org/patch/14648/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The sync_cmos_clock function in kernel/time/ntp.c first tries to update
the internal clock of the cpu by calling the "update_persistent_clock64"
architecture specific function.  If this returns -ENODEV, it then tries
to update an external RTC using "rtc_set_ntp_time".

On the mips architecture, the weak implementation of the underlying
function would return 0 if it wasn't overridden.  This meant that the
sync_cmos_clock function would never try to update an external RTC
(if both CONFIG_GENERIC_CMOS_UPDATE and CONFIG_RTC_SYSTOHC are
configured)

Returning -ENODEV instead, means that an external RTC will be tried.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Reviewed-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Reviewed-by: Scott Parlane <scott.parlane@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14649/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In commit 02cea395 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.

This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bimmy Pujari <bimmy.pujari@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case.  During
autonegotiation, the PHYs will determine whether to enable pause
frame support.

Pause frames are a feature that is supported by the MAC.  It is the MAC
that generates the frames and that processes them.  The PHY can only be
configured to allow them to pass through.

This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").

So the new process is:

1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported.  This indicates that
the PHY supports pause frames.

2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.

3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause,  If the bits are set, then it enables the corresponding
features in the MAC.  The algorithm is:

	if (phydev->pause)
		The MAC should be programmed to receive and honor
                pause frames it receives, i.e. enable receive flow control.

	if (phydev->pause != phydev->asym_pause)
		The MAC should be programmed to transmit pause
		frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>

PPPOL2TP_MSG_* and L2TP_MSG_* are duplicates, and are being used
interchangeably in the kernel, so let's standardize on L2TP_MSG_*
internally, and keep PPPOL2TP_MSG_* defined in UAPI for compatibility.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the L2TP_MSG_* definitions to UAPI, as it is part of
the netlink API.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lino Sanfilippo says:

====================
Remove private tx queue locks

this patch series removes unnecessary private locks in the sxgbe and the
stmmac driver.

v2:
- adjust commit message
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.

On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.

Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.

On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.

Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: bridge: fast ageing on topology change

802.1D [1] specifies that the bridges in a network must use a short
value to age out dynamic entries in the Filtering Database for a period,
once a topology change has been communicated by the root bridge.

This patchset fixes this for the in-kernel STP implementation.

Once the topology change flag is set in a net_bridge instance, the
ageing time value is shorten to twice the forward delay used by the
topology.

When the topology change flag is cleared, the ageing time configured for
the bridge is restored.

To accomplish that, a new bridge_ageing_time member is added to the
net_bridge structure, to store the user configured bridge ageing time.

Two helpers are added to offload the ageing time and set the topology
change flag in the net_bridge instance. Then the required logic is added
in the topology change helper if in-kernel STP is used.

This has been tested on the following topology:

    +--------------+
    | root bridge  |
    |  1  2  3  4  |
    +--+--+--+--+--+
       |  |  |  |      +--------+
       |  |  |  +------| laptop |
       |  |  |         +--------+
    +--+--+--+-----+
    |  1  2  3     |
    | slave bridge |
    +--------------+

When unplugging/replugging the laptop, the slave bridge (under test)
gets the topology change flag sent by the root bridge, and fast ageing
is triggered on the bridges. Once the topology change timer of the root
bridge expires, the topology change flag is cleared and the configured
ageing time is restored on the bridges.

A similar test has been done between two bridges under test.
When changing the forward delay of the root bridge with:

    # echo 3000 > /sys/class/net/br0/bridge/forward_delay

the ageing time correctly changes on both bridges from 300s to 60s while
the TOPOLOGY_CHANGE flag is present.

[1] "8.3.5 Notifying topology changes",
    http://profesores.elo.utfsm.cl/~agv/elo309/doc/802.1D-1998.pdf

No change since RFC: https://lkml.org/lkml/2016/10/19/828
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

802.1D [1] specifies that the bridges must use a short value to age out
dynamic entries in the Filtering Database for a period, once a topology
change has been communicated by the root bridge.

Add a bridge_ageing_time member in the net_bridge structure to store the
bridge ageing time value configured by the user (ioctl/netlink/sysfs).

If we are using in-kernel STP, shorten the ageing time value to twice
the forward delay used by the topology when the topology change flag is
set. When the flag is cleared, restore the configured ageing time.

[1] "8.3.5 Notifying topology changes ",
    http://profesores.elo.utfsm.cl/~agv/elo309/doc/802.1D-1998.pdfSigned-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a __br_set_topology_change helper to set the topology change value.

This can be later extended to add actions when the topology change flag
is set or cleared.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.

Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed

The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the same, more convenient macros, to get active slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:

drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'

This adds an explicit select for the part of the driver that has
the dependency.

Fixes: a0627f77 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes a newline which was added
in socket.c file in net-next
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_chain is called in ->release(), which is apparently
a process context, so we don't have to use an atomic notifier
here.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - Fix pointer size when caam is used with AArch64 boot loader on
     AArch32 kernel.

   - Fix ahash state corruption in marvell driver.

   - Fix buggy algif_aed tag handling.

   - Prevent mcryptd from being used with incompatible algorithms which
     can cause crashes"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: algif_aead - fix uninitialized variable warning
  crypto: mcryptd - Check mcryptd algorithm compatibility
  crypto: algif_aead - fix AEAD tag memory handling
  crypto: caam - fix pointer size for AArch64 boot loader, AArch32 kernel
  crypto: marvell - Don't corrupt state of an STD req for re-stepped ahash
  crypto: marvell - Don't copy hash operation twice into the SRAM

Pull networking fixes from David Miller:

 1) Limit the number of can filters to avoid > MAX_ORDER allocations.
    Fix from Marc Kleine-Budde.

 2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
    configurations. From Stephen Hemminger.

 3) Return proper error when memory allocation fails in
    ser_gigaset_init(), from Dan Carpenter.

 4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
    Feng.

 5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
    Florian Fainelli.

 6) Handle probe deferral properly in smsc911x driver.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: mlx5: Fix Kconfig help text
  net: smsc911x: back out silently on probe deferrals
  ibmveth: set correct gso_size and gso_type
  net: ethernet: cpmac: Call SET_NETDEV_DEV()
  net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
  vhost-vsock: fix orphan connection reset
  cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
  driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
  ser_gigaset: return -ENOMEM on error instead of success
  NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
  can: peak: fix bad memory access and free sequence
  phy: Don't increment MDIO bus refcount unless it's a different owner
  netvsc: reduce maximum GSO size
  drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
  can: raw: raw_setsockopt: limit number of can_filter that can be set

Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.

Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems attackers can also send UDP packets with no payload at all.

skb_condense() can still be a win in this case.

It will be possible to replace the custom code in tcp_add_backlog()
to get full benefit from skb_condense()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When trying to get a regulator we may get deferred and we see
this noise:

smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
   couldn't get regulators -517

Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.

Fix this by returning silently on deferred probe and let the
system work it out.

Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Three fixes:
 * fix a logic bug introduced by a previous cleanup
 * fix nl80211 attribute confusing (trying to use
   a single attribute for two purposes)
 * fix a long-standing BSS leak that happens when an
   association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:

"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.

We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."

We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.

Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
udp: receive path optimizations

This patch series provides about 100 % performance increase under flood.

v2: added Paolo feedback on udp_rmem_release() for tiny sk_rcvbuf
    added the last patch touching sk_rmem_alloc later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.

It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.

We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.

This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>