- 25 May, 2017 4 commits
-
-
Joe Carnuccio authored
Firmware dump allows for debugging customer issues. This patch fixes start/end pointer calculation to capture T262 template entry for dump tool. Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by:
Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Sawan Chandak authored
when driver is loaded with Multi Queue enabled, it was noticed that there was one less queue pair created. Following message would indicate this: "No resources to create additional q pair." The result of one less queue pair means that system can crash, if the block mq layer thinks there is an extra hardware queue available, and the driver will use a NULL ptr qpair in that instance. Following stack trace is seen in one of the crash: irq_create_affinity_masks+0x98/0x530 irq_create_affinity_masks+0x98/0x530 __pci_enable_msix+0x321/0x4e0 mutex_lock+0x12/0x40 pci_alloc_irq_vectors_affinity+0xb5/0x140 qla24xx_enable_msix+0x79/0x530 [qla2xxx] qla2x00_request_irqs+0x61/0x2d0 [qla2xxx] qla2x00_probe_one+0xc73/0x2390 [qla2xxx] ida_simple_get+0x98/0x100 kernfs_next_descendant_post+0x40/0x50 local_pci_probe+0x45/0xa0 pci_device_probe+0xfc/0x140 driver_probe_device+0x2c5/0x470 __driver_attach+0xdd/0xe0 driver_probe_device+0x470/0x470 bus_for_each_dev+0x6c/0xc0 driver_attach+0x1e/0x20 bus_add_driver+0x45/0x270 driver_register+0x60/0xe0 __pci_register_driver+0x4c/0x50 qla2x00_module_init+0x1ce/0x21e [qla2xxx] Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by:
Sawan Chandak <sawan.chandak@cavium.com> Signed-off-by:
-
Quinn Tran authored
Remove redundant fc_host_port_name calls to prevent early access of scsi_host->shost_data buffer. This prevent null pointer access. Following stack trace is seen: BUG: unable to handle kernel NULL pointer dereference at 00000000000008 IP: qla24xx_report_id_acquisition+0x22d/0x3a0 [qla2xxx] Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by:
Quinn Tran <quinn.tran@cavium.com> Signed-off-by:
-
himanshu.madhani@cavium.com authored
scsi: qla2xxx: Fix recursive loop during target mode configuration for ISP25XX leaving system unresponsive Following messages are seen into system logs qla2xxx [0000:09:00.0]-00af:9: Performing ISP error recovery - ha=ffff98315ee30000. qla2xxx [0000:09:00.0]-504b:9: RISC paused -- HCCR=40, Dumping firmware. qla2xxx [0000:09:00.0]-d009:9: Firmware has been previously dumped (ffffba488c001000) -- ignoring request. qla2xxx [0000:09:00.0]-504b:9: RISC paused -- HCCR=40, Dumping firmware. See Bugzilla for details https://bugzilla.kernel.org/show_bug.cgi?id=195285 Fixes: d7459527 ("scsi: qla2xxx: Add multiple queue pair functionality.") Cc: <stable@vger.kernel.org> # v4.10+ Reported-by:
Laurence Oberman <loberman@redhat.com> Reported-by:
Anthony Bloodoff <anthony.bloodoff@gmail.com> Tested-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Signed-off-by:
-
- 24 May, 2017 11 commits
-
-
Maurizio Lombardi authored
If multiple tasks attempt to read the stats, it may happen that the start_req_done completion is re-initialized while still being used by another task, causing a list corruption. This patch fixes the bug by adding a mutex to serialize the calls to bnx2fc_get_host_stats(). WARNING: at lib/list_debug.c:48 list_del+0x6e/0xa0() (Not tainted) Hardware name: PowerEdge R820 list_del corruption. prev->next should be ffff882035627d90, but was ffff884069541588 Pid: 40267, comm: perl Not tainted 2.6.32-642.3.1.el6.x86_64 #1 Call Trace: [<ffffffff8107c691>] ? warn_slowpath_common+0x91/0xe0 [<ffffffff8107c796>] ? warn_slowpath_fmt+0x46/0x60 [<ffffffff812ad16e>] ? list_del+0x6e/0xa0 [<ffffffff81547eed>] ? wait_for_common+0x14d/0x180 [<ffffffff8106c4a0>] ? default_wake_function+0x0/0x20 [<ffffffff81547fd3>] ? wait_for_completion_timeout+0x13/0x20 [<ffffffffa05410b1>] ? bnx2fc_get_host_stats+0xa1/0x280 [bnx2fc] [<ffffffffa04cf630>] ? fc_stat_show+0x90/0xc0 [scsi_transport_fc] [<ffffffffa04cf8b6>] ? show_fcstat_tx_frames+0x16/0x20 [scsi_transport_fc] [<ffffffff8137c647>] ? dev_attr_show+0x27/0x50 [<ffffffff8113b9be>] ? __get_free_pages+0xe/0x50 [<ffffffff812170e1>] ? sysfs_read_file+0x111/0x200 [<ffffffff8119a305>] ? vfs_read+0xb5/0x1a0 [<ffffffff8119b0b6>] ? fget_light_pos+0x16/0x50 [<ffffffff8119a651>] ? sys_read+0x51/0xb0 [<ffffffff810ee1fe>] ? __audit_syscall_exit+0x25e/0x290 [<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Acked-by:
Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by:
-
Johannes Thumshirn authored
When pci_enable_device() or pci_enable_device_mem() fail in qla2x00_probe_one() we bail out but do a call to pci_disable_device(). This causes the dev_WARN_ON() in pci_disable_device() to trigger, as the device wasn't enabled previously. So instead of taking the 'probe_out' error path we can directly return *iff* one of the pci_enable_device() calls fails. Additionally rename the 'probe_out' goto label's name to the more descriptive 'disable_device'. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring") Cc: <stable@vger.kernel.org> Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
-
Varun Prakash authored
skb->data is assigned to task->hdr in cxgbi_conn_alloc_pdu(), skb gets freed after tx but task->hdr is still dereferenced in iscsi_tcp_task_xmit() to avoid this call skb_get() after allocating skb and free the skb in cxgbi_cleanup_task() or before allocating new skb in cxgbi_conn_alloc_pdu(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
manish.rangankar@cavium.com authored
Signed-off-by:
Manish Rangankar <manish.rangankar@cavium.com> Signed-off-by:
-
Nilesh Javali authored
max_fin_rt is the maximum re-transmission of FIN packets as part of the termination flow. After reaching this value the FW will send a single RESET. Signed-off-by:
Nilesh Javali <nilesh.javali@cavium.com> Signed-off-by:
-
manish.rangankar@cavium.com authored
Signed-off-by:
-
manish.rangankar@cavium.com authored
RIP: 0010:qedi_set_path+0x114/0x570 [qedi] Call Trace: [<ffffffffa0472923>] iscsi_if_recv_msg+0x623/0x14a0 [<ffffffff81307de6>] ? rhashtable_lookup_compare+0x36/0x70 [<ffffffffa047382e>] iscsi_if_rx+0x8e/0x1f0 [<ffffffff8155983d>] netlink_unicast+0xed/0x1b0 [<ffffffff81559c30>] netlink_sendmsg+0x330/0x770 [<ffffffff81510d60>] sock_sendmsg+0xb0/0xf0 [<ffffffff8101360b>] ? __switch_to+0x17b/0x4b0 [<ffffffff8163a2c8>] ? __schedule+0x2d8/0x900 [<ffffffff81511199>] ___sys_sendmsg+0x3a9/0x3c0 [<ffffffff810e2298>] ? get_futex_key+0x1c8/0x2b0 [<ffffffff810e25a0>] ? futex_wake+0x80/0x160 Signed-off-by:
-
manish.rangankar@cavium.com authored
Signed-off-by:
-
manish.rangankar@cavium.com authored
Signed-off-by:
-
Arun Easi authored
munmap done by iscsiuio during a stop of the service triggers a "bad pte" warning sometimes. munmap kernel path goes through the mmapped pages and has a validation check for mapcount (in struct page) to be zero or above. kzalloc, which we had used to allocate udev->ctrl, uses slab allocations, which re-uses mapcount (union) for other purposes that can make the mapcount look negative. Avoid all these trouble by invoking one of the __get_free_pages wrappers to be used instead of kzalloc for udev->ctrl. BUG: Bad page map in process iscsiuio pte:80000000aa624067 pmd:3e6777067 page:ffffea0002a98900 count:2 mapcount:-2143289280 mapping: (null) index:0xffff8800aa624e00 page flags: 0x10075d00000090(dirty|slab) page dumped because: bad pte addr:00007fcba70a3000 vm_flags:0c0400fb anon_vma: (null) mapping:ffff8803edf66e90 index:0 Call Trace: dump_stack+0x19/0x1b print_bad_pte+0x1af/0x250 unmap_page_range+0x7a7/0x8a0 unmap_single_vma+0x81/0xf0 unmap_vmas+0x49/0x90 unmap_region+0xbe/0x140 ? vma_rb_erase+0x121/0x220 do_munmap+0x245/0x420 vm_munmap+0x41/0x60 SyS_munmap+0x22/0x30 tracesys+0xdd/0xe2 Signed-off-by:Arun Easi <arun.easi@cavium.com> Signed-off-by:
-
Artem Savkov authored
rdac_failover_get references struct rdac_controller as ctlr->ms_sdev->handler_data->ctlr for no apparent reason. Besides being inefficient this also introduces a null-pointer dereference as send_mode_select() sets ctlr->ms_sdev to NULL before calling rdac_failover_get(): [ 18.432550] device-mapper: multipath service-time: version 0.3.0 loaded [ 18.436124] BUG: unable to handle kernel NULL pointer dereference at 0000000000000790 [ 18.436129] IP: send_mode_select+0xca/0x560 [ 18.436129] PGD 0 [ 18.436130] P4D 0 [ 18.436130] [ 18.436132] Oops: 0000 [#1] SMP [ 18.436133] Modules linked in: dm_service_time sd_mod dm_multipath amdkfd amd_iommu_v2 radeon(+) i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm qla2xxx drm serio_raw scsi_transport_fc bnx2 i2c_core dm_mirror dm_region_hash dm_log dm_mod [ 18.436143] CPU: 4 PID: 443 Comm: kworker/u16:2 Not tainted 4.12.0-rc1.1.el7.test.x86_64 #1 [ 18.436144] Hardware name: IBM BladeCenter LS22 -[79013SG]-/Server Blade, BIOS -[L8E164AUS-1.07]- 05/25/2011 [ 18.436145] Workqueue: kmpath_rdacd send_mode_select [ 18.436146] task: ffff880225116a40 task.stack: ffffc90002bd8000 [ 18.436148] RIP: 0010:send_mode_select+0xca/0x560 [ 18.436148] RSP: 0018:ffffc90002bdbda8 EFLAGS: 00010246 [ 18.436149] RAX: 0000000000000000 RBX: ffffc90002bdbe08 RCX: ffff88017ef04a80 [ 18.436150] RDX: ffffc90002bdbe08 RSI: ffff88017ef04a80 RDI: ffff8802248e4388 [ 18.436151] RBP: ffffc90002bdbe48 R08: 0000000000000000 R09: ffffffff81c104c0 [ 18.436151] R10: 00000000000001ff R11: 000000000000035a R12: ffffc90002bdbdd8 [ 18.436152] R13: ffff8802248e4390 R14: ffff880225152800 R15: ffff8802248e4400 [ 18.436153] FS: 0000000000000000(0000) GS:ffff880227d00000(0000) knlGS:0000000000000000 [ 18.436154] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 18.436154] CR2: 0000000000000790 CR3: 000000042535b000 CR4: 00000000000006e0 [ 18.436155] Call Trace: [ 18.436159] ? rdac_activate+0x14e/0x150 [ 18.436161] ? refcount_dec_and_test+0x11/0x20 [ 18.436162] ? kobject_put+0x1c/0x50 [ 18.436165] ? scsi_dh_activate+0x6f/0xd0 [ 18.436168] process_one_work+0x149/0x360 [ 18.436170] worker_thread+0x4d/0x3c0 [ 18.436172] kthread+0x109/0x140 [ 18.436173] ? rescuer_thread+0x380/0x380 [ 18.436174] ? kthread_park+0x60/0x60 [ 18.436176] ret_from_fork+0x2c/0x40 [ 18.436177] Code: 49 c7 46 20 00 00 00 00 4c 89 ef c6 07 00 0f 1f 40 00 45 31 ed c7 45 b0 05 00 00 00 44 89 6d b4 4d 89 f5 4c 8b 75 a8 49 8b 45 20 <48> 8b b0 90 07 00 00 48 8b 56 10 8b 42 10 48 8d 7a 28 85 c0 0f [ 18.436192] RIP: send_mode_select+0xca/0x560 RSP: ffffc90002bdbda8 [ 18.436192] CR2: 0000000000000790 [ 18.436198] ---[ end trace 40f3e4dca1ffabdd ]--- [ 18.436199] Kernel panic - not syncing: Fatal exception [ 18.436222] Kernel Offset: disabled [-- MARK -- Thu May 18 11:45:00 2017] Fixes: 32782557 scsi_dh_rdac: switch to scsi_execute_req_flags() Cc: stable@vger.kernel.org Signed-off-by:
Artem Savkov <asavkov@redhat.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
- 19 May, 2017 3 commits
-
-
Long Li authored
In lower layer driver's (LLD) scsi_host_template, the driver may optionally ask SCSI to allocate its private driver memory for each command, by specifying cmd_size. This memory is allocated at the end of scsi_cmnd by SCSI. Later when SCSI queues a command, the LLD can use scsi_cmd_priv to get to its private data. Some LLD, e.g. hv_storvsc, doesn't clear its private data before use. In this case, the LLD may get to stale or uninitialized data in its private driver memory. This may result in unexpected driver and hardware behavior. Fix this problem by also zeroing the private driver memory before passing them to LLD. Signed-off-by:
Long Li <longli@microsoft.com> Reviewed-by:
KY Srinivasan <kys@microsoft.com> Reviewed-by:
Christoph Hellwig <hch@infradead.org> CC: <stable@vger.kernel.org> # 4.11+ Signed-off-by:
-
Varun Prakash authored
mbp pointer is passed to csio_hw_validate_caps() so call mempool_free() after calling csio_hw_validate_caps(). Signed-off-by:
-
Michał Potomski authored
When reloading module these two attributes aren't cleaned up properly and they persist causing warnings when trying to load module again. Additionally they are not recreated properly due to that. Signed-off-by:
Michał Potomski <michalx.potomski@intel.com> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
- 18 May, 2017 2 commits
-
-
James Smart authored
fix build issue if NVME_FC_TARGET is not defined. noop the code. The code will never be invoked if target mode is not enabled. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
Guilherme G. Piccoli authored
Recent commit on patchset "lpfc updates for 11.2.0.14" fixed an issue about dereferencing a NULL pointer on port reset. The specific commit, named "lpfc: Fix system crash when port is reset.", is missing a check against NULL pointer on lpfc_els_flush_cmd() though. Since we destroy the queues on adapter resets, like in PCI error recovery path, we need the validation present on this patch in order to avoid a NULL pointer dereference when trying to flush commands of ELS wq, after it has been destroyed (which would lead to a kernel oops). Tested-by:
Raphael Silva <raphasil@linux.vnet.ibm.com> Signed-off-by:
Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by:
-
- 17 May, 2017 17 commits
-
-
James Smart authored
Change driver version to 11.2.0.14. Signed-off-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
James Smart authored
Added code to support Cisco MDS loopback diagnostic. The diagnostics run various loopbacks including one which loops-back frame through the driver. Signed-off-by:
-
James Smart authored
Code review of NVMEI's FC_PORT_ROLE_NVME_DISCOVERY looked wrong. Discussions with storage architecture team clarified NVMEI's audit of the PRLI response port roles. Following up discussion with code review showed a few minor corrections were required - especially in anticipation of NVME auto discovery. During PRLI, NVMEI should sent prli_init - which it it does. NVMET should send prli_tgt and prli_disc - which it does. When NVMEI receives a PRLI Response now, it audits the incoming target bits and stores the attributes in the corresponding NDLP. Later, when NVMEI registers the NVME rport, it uses the stored ndlp attributes to set the rport port_roles correctly. Signed-off-by:
-
James Smart authored
Too many work items being processed in IRQ context take a lot of CPU time and cause problems. With a recent change, we get out of the ISR after hitting entry_repost work items on a queue. However, the actual values for entry repost are still high. EQ is 128 and CQ is 128, this could translate into processing 128 * 128 (16384) work items under IRQ context. Set entry_repost in the actual queue creation routine now. Limit EQ repost to 8 and CQ repost to 64 to further limit the amount of time spent in the IRQ. Fix fof IRQ routines as well. Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
James Smart authored
When unloading and reloading the driver, the driver fails to recreate the lpfc root inode in the debugfs tree. The driver is incorrectly removing the lpfc root inode in lpfc_debugfs_terminate in the first driver instance that unloads and then sets the lpfc_debugfs_root global parameter to NULL. When the final driver instance unloads, the debugfs calls quietly ignore the remove on a NULL pointer. The bug is that the debugfs_remove call returns void so the driver doesn't know to correctly set the global parameter to NULL. Base the debugfs_remove of the lpfc_debugfs_root parameter on lpfc_debugfs_hba_count because this parameter tracks the fnX instance tracked per driver instance. Signed-off-by:
-
James Smart authored
When the driver send the RPA command, it does not send supported FC4 Type NVME to the management server. Encode NVME (type x28) in the AttribEntry in the RPA command. Signed-off-by:
-
James Smart authored
Previous logic would just drop the IO. Added logic to queue the IO to wait for an IO context resource from an IO thats already in progress. Signed-off-by:
-
James Smart authored
Currently IO resources are mapped 1 to 1 with RQ buffers posted Added logic to separate RQE buffers from IO op resources (sgl/iocbq/context). During initialization, the driver will determine how many SGLs it will allocate for NVMET (based on what the firmware reports) and associate a NVMET IOCBq and NVMET context structure with each one. Now that hdr/data buffers are immediately reposted back to the RQ, 512 RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now 128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will always post the max (512) buffers per NVMET MRQ. Signed-off-by:
-
James Smart authored
Using 2048 byte buffer and onle 128 bytes is needed. Create nee LFPC_NVMET_DATA_BUF_SIZE define to use for NVMET RQ/MRQs. Signed-off-by:
-
James Smart authored
After running IOPS test for 30 second we get kernel:NMI watchdog: Watchdog detected hard LOCKUP on cpu 0 The driver is speend too much time in its ISR. In ISR EQ and CQ processing routines, if we hit the entry_repost numbers of EQE/CQEs just break out of the routine as opposed to hitting the doorbell with NOARM and continue processing. Signed-off-by:
-
James Smart authored
During driver boot, a latency in the NVMET driver side causes the incoming NVMEI PRLI to get rejected by the NVMET driver. When this happens, the NVMEI driver runs out of PRLI retries. Bouncing the link does not fix the situation. If the NVMEI driver decides, on PRLI completion failures, to retry the PRLI, always decrement the fc4_prli_sent counter. This allows the PRLI completion to resolve to UNMAPPED when NVMET rejects the PRLI. Signed-off-by:
-
James Smart authored
Large block writes to the nvme target were failing because the default number of RQs posted was insufficient. Expand the NVMET RQs to 2048 RQEs and ensure a minimum of 512 RQEs are posted, no matter how many MRQs are configured. Signed-off-by:
-
James Smart authored
More debug messages added for nvme statistics. Signed-off-by:
-
James Smart authored
The driver panic when using the els_wq during port reset. Check for NULL els_wq before dereferencing. Signed-off-by:
-
James Smart authored
With 255 vports created a link trasition can casue a crash. When going through discovery after a link bounce the driver is using rpis before the cmd FCOE_POST_HDR_TEMPLATES completes. By doing that the next rpi bumps the rpi range out of the boundary. The fix it to increment the next_rpi only when the FCOE_POST_HDR_TEMPLATE succeeds. Signed-off-by:
-
Gustavo A. R. Silva authored
Previous assignment was causing the use of the uninitialized variable _explan_ inside fc_seq_ls_rjt() function, which in this particular case is being called by fc_seq_els_rsp_send(). [mkp: fixed typo] Addresses-Coverity-ID: 1398125 Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Derek Basehore authored
Some external hard drives don't support the sync command even though the hard drive has write cache enabled. In this case, upon suspend request, sync cache failures are ignored if the error code in the sense header is ILLEGAL_REQUEST. There's not much we can do for these drives, so we shouldn't fail to suspend for this error case. The drive may stay powered if that's the setup for the port it's plugged into. Signed-off-by:
Derek Basehore <dbasehore@chromium.org> Signed-off-by:
Thierry Escande <thierry.escande@collabora.com> Reviewed-by:
-
- 12 May, 2017 3 commits
-
-
Johannes Thumshirn authored
If the list search in sg_get_rq_mark() fails to find a valid request, we return a bogus element. This then can later lead to a GPF in sg_remove_scat(). So don't return bogus Sg_requests in sg_get_rq_mark() but NULL in case the list search doesn't find a valid request. Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Doug Gilbert <dgilbert@interlog.com> Reviewed-by:
Doug Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Damien Le Moal authored
For a zoned block device, sd_zbc_complete() handles zone write unlock on completion of a REQ_OP_WRITE_ZEROES command but the zone write locking is missing from sd_setup_write_zeroes_cmnd(). This patch fixes this problem by locking the target zone of a REQ_OP_WRITE_ZEROES request. Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
-
Damien Le Moal authored
scsi_io_init() may fail, leaving a zone of a zoned block device locked. Fix this by properly unlocking the write same request target zone if scsi_io_init() fails. Signed-off-by:
-
