Reorganize code by moving the desired interrupt mask definition
out of function. Also rearrange the enable/disable interrupt function
to prevent accidental over-writing of values in registers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After acquiring National Semiconductor, TI appears to have
changed the Vendor Model Number for the DP83848C PHYs,
add this new ID to supported IDs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper macro for defining dp83848 compatible phy devices.
Update copyright info.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The EVB (virtual bridge) functionality should be disabled on older BE3
and Lancer chips if SR-IOV is disabled in the NIC's BIOS. This setting
is identified by the zero value of total VFs reported by the card.
The GET_HSW_CONFIG command cannot be used as it is not supported by
these older chipset's FW.

v2: added the comment

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Helmut Buchsbaum says:

====================
Add support for MICREL KSZ8795CLX 5-port switch

This patch series refactors the spi-ks8995 driver to finally add support
for the MICREL KSZ8795CLX. Additionally support for controlling a GPIO
line for resetting the switch is added.

Helmut

Changes since v2:
 - use GPIO_ACTIVE_LOW according to Andrew's remark.
 - use ePAPR compliant node name in example, thanks to Sergei for
   pointing out
Changes since v1:
 - removed initializing registers from Device Tree following Florian's
   advice
 - fixed GPIO handling for reset according to Andrew's remark.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for MICREL KSZ8795CLX Integrated 5-Port, 10-/100-Managed
Ethernet Switch with Gigabit GMII/RGMII and MII/RMII interfaces.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare creating SPI reads and writes for other switch families.
The KS8995 family uses the straight forward
	<8bit CMD><8bit ADDR>
sequence.
To be able to support KSZ8795 family, which uses
	<3bit CMD><12bit ADDR><1 bit TR>
make the SPI command creation chip variant dependent.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allows to power down the switch
when it is not used any more.

The patch introduces a new optional property "reset-gpios" denoting an
appropriate GPIO handle, e.g.:

reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the chip variant is now determined by spi_device_id, verify
family and chip id and determine the revision id.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor to use spi_device_id table to facilitate easy
extendability.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
net: thunderx: Setting IRQ affinity hints and other optimizations

This patch series contains changes
- To add support for virtual function's irq affinity hint
- Replace napi_schedule() with napi_schedule_irqoff()
- Reduce page allocation overhead by allocating pages
  of higher order when pagesize is 4KB.
- Add couple of stats which helps in debugging
- Some miscellaneous changes to BGX driver.

Changes from v1:
- As suggested changed MAC address invalid log message
  to dev_err() instead of dev_warn().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate higher order pages when pagesize is small, this will
reduce number of calls to page allocator and wastage of memory.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of OF device tree, the firmware information is attached to
the BGX device structure in the standard manner, so use the firmware
iterators and accessors where possible.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This affinity hint can be used by user space irqbalance tool to set
preferred CPU mask for irqs registered by this VF. Irqbalance needs
to be in 'exact' mode to set irq affinity same as indicated by
affinity hint.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_schedule is being called from hard irq context, hence
switch to napi_schedule_irqoff which avoids unneeded call
to local_irq_save and local_irq_restore.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When system is low on atomic memory, too many error messages are logged.
Since this is not a total failure but a simple switch to non-atomic allocation
better to have a stat.

Also add a stat for reset, kicked due to transmit watchdog timeout.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Borisov says:

====================
Make igmp sysctl knobs namespace aware

This series continue making more of the net related sysctls
namespace aware. The first 2 and last patches are straight
forward and convert sysctls which weren't defined to be
namespace aware. The only thing in them is that each removes
a define which is used in only one place (to initialise
the respective sysctl) so I don't think this is a huge loss.

The third patch however, converts igmp_llm_reports which was
already defined in the ipv4_net_table but wasn't using any of
the net namespace infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was initially introduced in df2cf4a7 ("IGMP: Inhibit
reports for local multicast groups") by defining the sysctl in the
ipv4_net_table array, however it was never implemented to be
namespace aware. Fix this by changing the code accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace 'goto' with 'return' to remove unnecessary check at label:
err_undo_flags.

The reason is that 'err_undo_flags' do two things for the first slave device:
1.revert bond mac address if it is set by the slave device.
2.revert bond device type if it's not ARPHRD_ETHER.

It's not necessary for the following three places, they changed neither bond
mac address nor type. It's straightforward to return directly.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

32 bit systems using 'struct timeval' will break in the year 2038, so
we replace the code appropriately. However, this driver is not broken
in 2038 since we are only using microseconds portion of the time.

This patch replaces 'struct timeval' with 'struct timespec64'. We only
need to find elapsed microseconds rather than absolute time, so it's
better to use monotonic time, so using ktime_get_ts64() makes the code
more efficient and more robust against concurrent settimeofday()
calls.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Operations with the GENL_ADMIN_PERM flag fail permissions checks because
this flag means we call netlink_capable, which uses the init user ns.

Instead, let's introduce a new flag, GENL_UNS_ADMIN_PERM for operations
which should be allowed inside a user namespace.

The motivation for this is to be able to run openvswitch in unprivileged
containers. I've tested this and it seems to work, but I really have no
idea about the security consequences of this patch, so thoughts would be
much appreciated.

v2: use the GENL_UNS_ADMIN_PERM flag instead of a check in each function
v3: use separate ifs for UNS_ADMIN_PERM and ADMIN_PERM, instead of one
    massive one
Reported-by: James Page <james.page@canonical.com>
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com>
CC: Eric Biederman <ebiederm@xmission.com>
CC: Pravin Shelar <pshelar@ovn.org>
CC: Justin Pettit <jpettit@nicira.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many virtual and not quite virtual devices allow any speed to be set
through ethtool. In particular, this applies to the virtio-net devices.
Document this fact to make sure people don't assume the enum lists all
possible values.  Reserve values greater than INT_MAX for future
extension and to avoid conflict with SPEED_UNKNOWN.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Duplicate include detected.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.

Found using Coccinelle. A simplified version of the semantic patch
used is:

//<smpl>
@@
expression *e;
@@

e = kzalloc(...);
if (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>

The single call site only checks that the return value is not 0,
hence no change is required at the call site.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
Add GSO support for outer checksum w/ inner checksum offloads

This patch series updates the existing segmentation offload code for
tunnels to make better use of existing and updated GSO checksum
computation.  This is done primarily through two mechanisms.  First we
maintain a separate checksum in the GSO context block of the sk_buff.  This
allows us to maintain two checksum values, one offloaded with values stored
in csum_start and csum_offset, and one computed and tracked in
SKB_GSO_CB(skb)->csum.  By maintaining these two values we are able to take
advantage of the same sort of math used in local checksum offload so that
we can provide both inner and outer checksums with minimal overhead.

Below is the performance for a netperf session between an ixgbe PF and VF
on the same host but in different namespaces.  As can be seen a significant
gain in performance can be had from allowing the use of Tx checksum offload
on the inner headers while performing a software offload on the outer
header computation:

 Recv   Send   Send                       Utilization  Service Demand
 Socket Socket Message Elapsed            Send  Recv   Send  Recv
 Size   Size   Size    Time    Throughput local remote local remote
 bytes  bytes  bytes   secs.   10^6bits/s % S   % U    us/KB us/KB

Before:
 87380  16384  16384   10.00   12844.38   9.30  -1.00  0.712 -1.00
After:
 87380  16384  16384   10.00   13216.63   6.78  -1.00  0.504 -1.000

Changes from v1:
* Dropped use of CHECKSUM_UNNECESSARY for remote checksum offload
* Left encap_hdr_csum as it will likely be needed in future for SCTP GSO
* Broke the changes out over many more patches
* Updated GRE segmentation to more closely match UDP tunnel segmentation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables us to use inner checksum offloads if provided by
hardware with outer checksums computed by software.

It basically reduces encap_hdr_csum to an advisory flag for now, but based
on the fact that SCTP may be getting segmentation support before long I
thought we may want to keep it as it is possible we may need to support
CRC32c and 1's compliment checksum in the same packet at some point in the
future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The segmentation code was having to do a bunch of work to pull the
skb->len and strip the udp header offset before the value could be used to
adjust the checksum.  Instead of doing all this work we can just use the
value that goes into uh->len since that is the correct value with the
correct byte order that we need anyway.  By using this value we can save
ourselves a bunch of pain as there is no need to do multiple byte swaps.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch goes though and cleans up the logic related to several of the
control flags used in UDP segmentation.  Specifically the use of dont_encap
isn't really needed as we can just check the skb for CHECKSUM_PARTIAL and
if it isn't set then we don't need to update the internal headers.  As such
we can just drop that value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of parsing headers to determine the inner protocol we can just pull
the value from inner_proto.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the gre checksum path to follow something much closer to
the UDP checksum path.  By doing this we can avoid needing to do as much
header inspection and can just make use of the fields we were already
reading in the sk_buff structure.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The call skb_has_shared_frag is used in the GRE path and skb_checksum_help
to verify that no frags can be modified by an external entity.  This check
really doesn't belong in the GRE path but in the skb_segment function
itself.  This way any protocol that might be segmented will be performing
this check before attempting to offload a checksum to software.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes it so that we can offload the checksums for a packet up
to a certain point and then begin computing the checksums via software.
Setting this up is fairly straight forward as all we need to do is reset
the values stored in csum and csum_start for the GSO context block.

One complication for this is remote checksum offload.  In order to allow
the inner checksums to be offloaded while computing the outer checksum
manually we needed to have some way of indicating that the offload wasn't
real.  In order to do that I replaced CHECKSUM_PARTIAL with
CHECKSUM_UNNECESSARY in the case of us computing checksums for the outer
header while skipping computing checksums for the inner headers.  We clean
up the ip_summed flag and set it to either CHECKSUM_PARTIAL or
CHECKSUM_NONE once we hand the packet off to the next lower level.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>