- 24 Feb, 2020 9 commits
-
-
Esben Haabendal authored
This adds error handling to the remaining dma_map_single() calls, so that behavior is well defined if/when we run out of DMA memory. Fixes: 92744989 ("net: add Xilinx ll_temac device driver") Signed-off-by:
Esben Haabendal <esben@geanix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Esben Haabendal authored
It is possible that the interrupt handler fires and frees up space in the TX ring in between checking for sufficient TX ring space and stopping the TX queue in temac_start_xmit. If this happens, the queue wake from the interrupt handler will occur before the queue is stopped, causing a lost wakeup and the adapter's transmit hanging. To avoid this, after stopping the queue, check again whether there is sufficient space in the TX ring. If so, wake up the queue again. This is a port of the similar fix in axienet driver, commit 7de44285 ("net: axienet: Fix race condition causing TX hang"). Fixes: 23ecc4bd ("net: ll_temac: fix checksum offload logic") Signed-off-by:
-
Madhuparna Bhowmik authored
devlink_dpipe_table_find() should be called under either rcu_read_lock() or devlink->lock. devlink_dpipe_table_register() calls devlink_dpipe_table_find() without holding the lock and acquires it later. Therefore hold the devlink->lock from the beginning of devlink_dpipe_table_register(). Suggested-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Reviewed-by:
-
Florian Fainelli authored
It is currently possible for a PHY device to be suspended as part of a network device driver's suspend call while it is still being attached to that net_device, either via phy_suspend() or implicitly via phy_stop(). Later on, when the MDIO bus controller get suspended, we would attempt to suspend again the PHY because it is still attached to a network device. This is both a waste of time and creates an opportunity for improper clock/power management bugs to creep in. Fixes: 803dd9c7 ("net: phy: avoid suspending twice a PHY") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Marek Vasut authored
The KS8851 requires that packet RX and TX are mutually exclusive. Currently, the driver hopes to achieve this by disabling interrupt from the card by writing the card registers and by disabling the interrupt on the interrupt controller. This however is racy on SMP. Replace this approach by expanding the spinlock used around the ks_start_xmit() TX path to ks_irq() RX path to assure true mutual exclusion and remove the interrupt enabling/disabling, which is now not needed anymore. Furthermore, disable interrupts also in ks_net_stop(), which was missing before. Note that a massive improvement here would be to re-use the KS8851 driver approach, which is to move the TX path into a worker thread, interrupt handling to threaded interrupt, and synchronize everything with mutexes, but that would be a much bigger rework, for a separate patch. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Jonathan Neuschäfer authored
Let's make it a little easier to read. Signed-off-by:
Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by:
-
Neal Cardwell authored
In a rare corner case the new logic for undo of SYNACK RTO could result in triggering the warning in tcp_fastretrans_alert() that says: WARN_ON(tp->retrans_out != 0); The warning looked like: WARNING: CPU: 1 PID: 1 at net/ipv4/tcp_input.c:2818 tcp_ack+0x13e0/0x3270 The sequence that tickles this bug is: - Fast Open server receives TFO SYN with data, sends SYNACK - (client receives SYNACK and sends ACK, but ACK is lost) - server app sends some data packets - (N of the first data packets are lost) - server receives client ACK that has a TS ECR matching first SYNACK, and also SACKs suggesting the first N data packets were lost - server performs TS undo of SYNACK RTO, then immediately enters recovery - buggy behavior then performed a *second* undo that caused the connection to be in CA_Open with retrans_out != 0 Basically, the incoming ACK packet with SACK blocks causes us to first undo the cwnd reduction from the SYNACK RTO, but then immediately enters fast recovery, which then makes us eligible for undo again. And then tcp_rcv_synrecv_state_fastopen() accidentally performs an undo using a "mash-up" of state from two different loss recovery phases: it uses the timestamp info from the ACK of the original SYNACK, and the undo_marker from the fast recovery. This fix refines the logic to only invoke the tcp_try_undo_loss() inside tcp_rcv_synrecv_state_fastopen() if the connection is still in CA_Loss. If peer SACKs triggered fast recovery, then tcp_rcv_synrecv_state_fastopen() can't safely undo. Fixes: 794200d6 ("tcp: undo cwnd on Fast Open spurious SYNACK retransmit") Signed-off-by:Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Haiyang Zhang authored
When netvsc_attach() is called by operations like changing MTU, etc., an extra wakeup may happen while netvsc_attach() calling rndis_filter_device_add() which sends rndis messages when queue is stopped in netvsc_detach(). The completion message will wake up queue 0. We can reproduce the issue by changing MTU etc., then the wake_queue counter from "ethtool -S" will increase beyond stop_queue counter: stop_queue: 0 wake_queue: 1 The issue causes queue wake up, and counter increment, no other ill effects in current code. So we didn't see any network problem for now. To fix this, initialize tx_disable to true, and set it to false when the NIC is ready to be attached or registered. Fixes: 7b2ee50c ("hv_netvsc: common detach logic") Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Daniele Palmas authored
usbnet creates network interfaces with min_mtu = 0 and max_mtu = ETH_MAX_MTU. These values are not modified by qmi_wwan when the network interface is created initially, allowing, for example, to set mtu greater than 1500. When a raw_ip switch is done (raw_ip set to 'Y', then set to 'N') the mtu values for the network interface are set through ether_setup, with min_mtu = ETH_MIN_MTU and max_mtu = ETH_DATA_LEN, not allowing anymore to set mtu greater than 1500 (error: mtu greater than device maximum). The patch restores the original min/max mtu values set by usbnet after a raw_ip switch. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
- 23 Feb, 2020 3 commits
-
-
Paolo Abeni authored
Currently if attribute parsing fails and the genl family does not support parallel operation, the error code returned by __nlmsg_parse() is discarded by genl_family_rcv_msg_attrs_parse(). Be sure to report the error for all genl families. Fixes: c10e6cf8 ("net: genetlink: push attrbuf allocation and parsing to a separate function") Fixes: ab5b526d ("net: genetlink: always allocate separate attrs for dumpit ops") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Matteo Croce authored
Similarly to commit c543cb4a ("ipv4: ensure rcu_read_lock() in ipv4_link_failure()"), __ip_options_compile() must be called under rcu protection. Fixes: 3da1ed7a ("net: avoid use IPCB in cipso_v4_error") Suggested-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
Matteo Croce <mcroce@redhat.com> Acked-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Eugenio Pérez authored
Doing so, we save one call to get data we already have in the struct. Also, since there is no guarantee that getname use sockaddr_ll parameter beyond its size, we add a little bit of security here. It should do not do beyond MAX_ADDR_LEN, but syzbot found that ax25_getname writes more (72 bytes, the size of full_sockaddr_ax25, versus 20 + 32 bytes of sockaddr_ll + MAX_ADDR_LEN in syzbot repro). Fixes: 3a4d5c94 ("vhost_net: a kernel-level virtio server") Reported-by: syzbot+f2a62d07a5198c819c7b@syzkaller.appspotmail.com Signed-off-by:
Eugenio Pérez <eperezma@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
- 21 Feb, 2020 28 commits
-
-
git://www.linux-watchdog.org/linux-watchdogLinus Torvalds authored
Pull watchdog fixes from Wim Van Sebroeck: - mtk_wdt needs RESET_CONTROLLER to build - da9062 driver fixes: - fix power management ops - do not ping the hw during stop() - add dependency on I2C * tag 'linux-watchdog-5.6-rc3' of git://www.linux-watchdog.org/linux-watchdog: watchdog: da9062: Add dependency on I2C watchdog: da9062: fix power management ops watchdog: da9062: do not ping the hw during stop() watchdog: fix mtk_wdt.c RESET_CONTROLLER build error -
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char/misc driver fixes from Greg KH: "Here are some small char/misc driver fixes for 5.6-rc3. Also included in here are some updates for some documentation files that I seem to be maintaining these days. The driver fixes are: - small fixes for the habanalabs driver - fsi driver bugfix All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: Documentation/process: Swap out the ambassador for Canonical habanalabs: patched cb equals user cb in device memset habanalabs: do not halt CoreSight during hard reset habanalabs: halt the engines before hard-reset MAINTAINERS: remove unnecessary ':' characters fsi: aspeed: add unspecified HAS_IOMEM dependency COPYING: state that all contributions really are covered by this file Documentation/process: Change Microsoft contact for embargoed hardware issues embargoed-hardware-issues: drop Amazon contact as the email address now bounces Documentation/process: Add Arm contact for embargoed HW issues
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging driver fixes from Greg KH: "Here are some small staging driver fixes for 5.6-rc3, along with the removal of an unused/unneeded driver as well. The android vsoc driver is not needed anymore by anyone, so it was removed. The other driver fixes are: - ashmem bugfixes - greybus audio driver bugfix - wireless driver bugfixes and tiny cleanups to error paths All of these have been in linux-next for a while now with no reported issues" * tag 'staging-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: rtl8723bs: Remove unneeded goto statements staging: rtl8188eu: Remove some unneeded goto statements staging: rtl8723bs: Fix potential overuse of kernel memory staging: rtl8188eu: Fix potential overuse of kernel memory staging: rtl8723bs: Fix potential security hole staging: rtl8188eu: Fix potential security hole staging: greybus: use after free in gb_audio_manager_remove_all() staging: android: Delete the 'vsoc' driver staging: rtl8723bs: fix copy of overlapping memory staging: android: ashmem: Disallow ashmem memory from being remapped staging: vt6656: fix sign of rx_dbm to bb_pre_ed_rssi.
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/ttyLinus Torvalds authored
Pull tty/serial driver fixes from Greg KH: "Here are a number of small tty and serial driver fixes for 5.6-rc3 that resolve a bunch of reported issues. They are: - vt selection and ioctl fixes - serdev bugfix - atmel serial driver fixes - qcom serial driver fixes - other minor serial driver fixes All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: vt: selection, close sel_buffer race vt: selection, handle pending signals in paste_selection serial: cpm_uart: call cpm_muram_init before registering console tty: serial: qcom_geni_serial: Fix RX cancel command failure serial: 8250: Check UPF_IRQ_SHARED in advance tty: serial: imx: setup the correct sg entry for tx dma vt: vt_ioctl: fix race in VT_RESIZEX vt: fix scrollback flushing on background consoles tty: serial: tegra: Handle RX transfer in PIO mode if DMA wasn't started tty/serial: atmel: manage shutdown in case of RS485 or ISO7816 mode serdev: ttyport: restore client ops on deregistration serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB/Thunderbolt fixes from Greg KH: "Here are a number of small USB driver fixes for 5.6-rc3. Included in here are: - MAINTAINER file updates - USB gadget driver fixes - usb core quirk additions and fixes for regressions - xhci driver fixes - usb serial driver id additions and fixes - thunderbolt bugfix Thunderbolt patches come in through here now that USB4 is really thunderbolt. All of these have been in linux-next for a while with no reported issues" * tag 'usb-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits) USB: misc: iowarrior: add support for the 100 device thunderbolt: Prevent crash if non-active NVMem file is read usb: gadget: udc-xilinx: Fix xudc_stop() kernel-doc format USB: misc: iowarrior: add support for the 28 and 28L devices USB: misc: iowarrior: add support for 2 OEMed devices USB: Fix novation SourceControl XL after suspend xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2 Revert "xhci: Fix memory leak when caching protocol extended capability PSI tables" MAINTAINERS: Sort entries in database for THUNDERBOLT usb: dwc3: debug: fix string position formatting mixup with ret and len usb: gadget: serial: fix Tx stall after buffer overflow usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags usb: dwc2: Fix SET/CLEAR_FEATURE and GET_STATUS flows usb: dwc2: Fix in ISOC request length checking usb: gadget: composite: Support more than 500mA MaxPower usb: gadget: composite: Fix bMaxPower for SuperSpeedPlus usb: gadget: u_audio: Fix high-speed max packet size usb: dwc3: gadget: Check for IOC/LST bit in TRB->ctrl fields USB: core: clean up endpoint-descriptor parsing USB: quirks: blacklist duplicate ep on Sound Devices USBPre2 ...
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm fixes from Dave Airlie: "Varied fixes for rc3. i915 is the largest, they are seeing some ACPI problems with their CI which hopefully get solved soon [1]. msm has a bunch of fixes for new hw added in the merge, a bunch of amdgpu fixes, and nouveau adds support for some new firmwares for turing tu11x GPUs that were just released into linux-firmware by nvidia, they operate the same as the ones we already have for tu10x so should be fine to hook up. Otherwise it's just misc fixes for panfrost and sun4i. core: - Allow only one rotation argument, and allow zero rotation in video cmdline. i915: - Workaround missing Display Stream Compression (DSC) state readout by forcing modeset when its enabled at probe - Fix EHL port clock voltage level requirements - Fix queuing retire workers on the virtual engine - Fix use of partially initialized waiters - Stop using drm_pci_alloc/drm_pci/free - Fix rewind of RING_TAIL by forcing a context reload - Fix locking on resetting ring->head - Propagate our bug filing URL change to stable kernels panfrost: - Small compiler warning fix for panfrost. - Fix when using performance counters in panfrost when using per fd address space. sun4xi: - Fix dt binding nouveau: - tu11x modesetting fix - ACR/GR firmware support for tu11x (fw is public now) msm: - fix UBWC on GPU and display side for sc7180 - fix DSI suspend/resume issue encountered on sc7180 - fix some breakage on so called "linux-android" devices (fallout from sc7180/a618 support, not seen earlier due to bootloader/firmware differences) - couple other misc fixes amdgpu: - HDCP fixes - xclk fix for raven - GFXOFF fixes" [1] The Intel suspend testing should now be fixed by commit 63fb9623 ("ACPI: PM: s2idle: Check fixed wakeup events in acpi_s2idle_wake()") * tag 'drm-fixes-2020-02-21' of git://anongit.freedesktop.org/drm/drm: (39 commits) drm/amdgpu/display: clean up hdcp workqueue handling drm/amdgpu: add is_raven_kicker judgement for raven1 drm/i915/gt: Avoid resetting ring->head outside of its timeline mutex drm/i915/execlists: Always force a context reload when rewinding RING_TAIL drm/i915: Wean off drm_pci_alloc/drm_pci_free drm/i915/gt: Protect defer_request() from new waiters drm/i915/gt: Prevent queuing retire workers on the virtual engine drm/i915/dsc: force full modeset whenever DSC is enabled at probe drm/i915/ehl: Update port clock voltage level requirements drm/i915: Update drm/i915 bug filing URL MAINTAINERS: Update drm/i915 bug filing URL drm/i915: Initialise basic fence before acquiring seqno drm/i915/gem: Require per-engine reset support for non-persistent contexts drm/nouveau/kms/gv100-: Re-set LUT after clearing for modesets drm/nouveau/gr/tu11x: initial support drm/nouveau/acr/tu11x: initial support drm/amdgpu/gfx10: disable gfxoff when reading rlc clock drm/amdgpu/gfx9: disable gfxoff when reading rlc clock drm/amdgpu/soc15: fix xclk for raven drm/amd/powerplay: always refetch the enabled features status on dpm enablement ... -
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Limit xt_hashlimit hash table size to avoid OOM or hung tasks, from Cong Wang. 2) Fix deadlock in xsk by publishing global consumer pointers when NAPI is finished, from Magnus Karlsson. 3) Set table field properly to RT_TABLE_COMPAT when necessary, from Jethro Beekman. 4) NLA_STRING attributes are not necessary NULL terminated, deal wiht that in IFLA_ALT_IFNAME. From Eric Dumazet. 5) Fix checksum handling in atlantic driver, from Dmitry Bezrukov. 6) Handle mtu==0 devices properly in wireguard, from Jason A. Donenfeld. 7) Fix several lockdep warnings in bonding, from Taehee Yoo. 8) Fix cls_flower port blocking, from Jason Baron. 9) Sanitize internal map names in libbpf, from Toke Høiland-Jørgensen. 10) Fix RDMA race in qede driver, from Michal Kalderon. 11) Fix several false lockdep warnings by adding conditions to list_for_each_entry_rcu(), from Madhuparna Bhowmik. 12) Fix sleep in atomic in mlx5 driver, from Huy Nguyen. 13) Fix potential deadlock in bpf_map_do_batch(), from Yonghong Song. 14) Hey, variables declared in switch statement before any case statements are not initialized. I learn something every day. Get rids of this stuff in several parts of the networking, from Kees Cook. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits) bnxt_en: Issue PCIe FLR in kdump kernel to cleanup pending DMAs. bnxt_en: Improve device shutdown method. net: netlink: cap max groups which will be considered in netlink_bind() net: thunderx: workaround BGX TX Underflow issue ionic: fix fw_status read net: disable BRIDGE_NETFILTER by default net: macb: Properly handle phylink on at91rm9200 s390/qeth: fix off-by-one in RX copybreak check s390/qeth: don't warn for napi with 0 budget s390/qeth: vnicc Fix EOPNOTSUPP precedence openvswitch: Distribute switch variables for initialization net: ip6_gre: Distribute switch variables for initialization net: core: Distribute switch variables for initialization udp: rehash on disconnect net/tls: Fix to avoid gettig invalid tls record bpf: Fix a potential deadlock with bpf_map_do_batch bpf: Do not grab the bucket spinlock by default on htab batch ops ice: Wait for VF to be reset/ready before configuration ice: Don't tell the OS that link is going down ice: Don't reject odd values of usecs set by user ... -
Linus Torvalds authored
Merge misc fixes from Andrew Morton: - A few y2038 fixes which missed the merge window while dependencies in NFS were being sorted out. - A bunch of fixes. Some minor, some not. * emailed patches from Andrew Morton <akpm@linux-foundation.org>: MAINTAINERS: use tabs for SAFESETID lib/stackdepot.c: fix global out-of-bounds in stack_slabs mm/sparsemem: pfn_to_page is not valid yet on SPARSEMEM mm/vmscan.c: don't round up scan size for online memory cgroup lib/string.c: update match_string() doc-strings with correct behavior mm/memcontrol.c: lost css_put in memcg_expand_shrinker_maps() mm/swapfile.c: fix a comment in sys_swapon() scripts/get_maintainer.pl: deprioritize old Fixes: addresses get_maintainer: remove uses of P: for maintainer name selftests/vm: add missed tests in run_vmtests include/uapi/linux/swab.h: fix userspace breakage, use __BITS_PER_LONG for swap Revert "ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()" y2038: hide timeval/timespec/itimerval/itimerspec types y2038: remove unused time32 interfaces y2038: remove ktime to/from timespec/timeval conversion
-
Randy Dunlap authored
Use tabs for indentation instead of spaces for SAFESETID. All (!) other entries in MAINTAINERS use tabs (according to my simple grepping). Link: http://lkml.kernel.org/r/2bb2e52a-2694-816d-57b4-6cabfadd6c1a@infradead.orgSigned-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Micah Morton <mortonm@chromium.org> Cc: James Morris <jmorris@namei.org> Cc: "Serge E. Hallyn" <serge@hallyn.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Alexander Potapenko authored
Walter Wu has reported a potential case in which init_stack_slab() is called after stack_slabs[STACK_ALLOC_MAX_SLABS - 1] has already been initialized. In that case init_stack_slab() will overwrite stack_slabs[STACK_ALLOC_MAX_SLABS], which may result in a memory corruption. Link: http://lkml.kernel.org/r/20200218102950.260263-1-glider@google.com Fixes: cd11016e ("mm, kasan: stackdepot implementation. Enable stackdepot for SLAB") Signed-off-by:
Alexander Potapenko <glider@google.com> Reported-by:
Walter Wu <walter-zh.wu@mediatek.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Wei Yang authored
When we use SPARSEMEM instead of SPARSEMEM_VMEMMAP, pfn_to_page() doesn't work before sparse_init_one_section() is called. This leads to a crash when hotplug memory: BUG: unable to handle page fault for address: 0000000006400000 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] SMP PTI CPU: 3 PID: 221 Comm: kworker/u16:1 Tainted: G W 5.5.0-next-20200205+ #343 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015 Workqueue: kacpi_hotplug acpi_hotplug_work_fn RIP: 0010:__memset+0x24/0x30 Code: cc cc cc cc cc cc 0f 1f 44 00 00 49 89 f9 48 89 d1 83 e2 07 48 c1 e9 03 40 0f b6 f6 48 b8 01 01 01 01 01 01 01 01 48 0f af c6 <f3> 48 ab 89 d1 f3 aa 4c 89 c8 c3 90 49 89 f9 40 88 f0 48 89 d1 f3 RSP: 0018:ffffb43ac0373c80 EFLAGS: 00010a87 RAX: ffffffffffffffff RBX: ffff8a1518800000 RCX: 0000000000050000 RDX: 0000000000000000 RSI: 00000000000000ff RDI: 0000000006400000 RBP: 0000000000140000 R08: 0000000000100000 R09: 0000000006400000 R10: 0000000000000000 R11: 0000000000000002 R12: 0000000000000000 R13: 0000000000000028 R14: 0000000000000000 R15: ffff8a153ffd9280 FS: 0000000000000000(0000) GS:ffff8a153ab00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000006400000 CR3: 0000000136fca000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: sparse_add_section+0x1c9/0x26a __add_pages+0xbf/0x150 add_pages+0x12/0x60 add_memory_resource+0xc8/0x210 __add_memory+0x62/0xb0 acpi_memory_device_add+0x13f/0x300 acpi_bus_attach+0xf6/0x200 acpi_bus_scan+0x43/0x90 acpi_device_hotplug+0x275/0x3d0 acpi_hotplug_work_fn+0x1a/0x30 process_one_work+0x1a7/0x370 worker_thread+0x30/0x380 kthread+0x112/0x130 ret_from_fork+0x35/0x40 We should use memmap as it did. On x86 the impact is limited to x86_32 builds, or x86_64 configurations that override the default setting for SPARSEMEM_VMEMMAP. Other memory hotplug archs (arm64, ia64, and ppc) also default to SPARSEMEM_VMEMMAP=y. [dan.j.williams@intel.com: changelog update] {rppt@linux.ibm.com: changelog update] Link: http://lkml.kernel.org/r/20200219030454.4844-1-bhe@redhat.com Fixes: ba72b4c8 ("mm/sparsemem: support sub-section hotplug") Signed-off-by:Wei Yang <richardw.yang@linux.intel.com> Signed-off-by:
Baoquan He <bhe@redhat.com> Acked-by:
David Hildenbrand <david@redhat.com> Reviewed-by:
Dan Williams <dan.j.williams@intel.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Gavin Shan authored
Commit 68600f62 ("mm: don't miss the last page because of round-off error") makes the scan size round up to @denominator regardless of the memory cgroup's state, online or offline. This affects the overall reclaiming behavior: the corresponding LRU list is eligible for reclaiming only when its size logically right shifted by @sc->priority is bigger than zero in the former formula. For example, the inactive anonymous LRU list should have at least 0x4000 pages to be eligible for reclaiming when we have 60/12 for swappiness/priority and without taking scan/rotation ratio into account. After the roundup is applied, the inactive anonymous LRU list becomes eligible for reclaiming when its size is bigger than or equal to 0x1000 in the same condition. (0x4000 >> 12) * 60 / (60 + 140 + 1) = 1 ((0x1000 >> 12) * 60) + 200) / (60 + 140 + 1) = 1 aarch64 has 512MB huge page size when the base page size is 64KB. The memory cgroup that has a huge page is always eligible for reclaiming in that case. The reclaiming is likely to stop after the huge page is reclaimed, meaing the further iteration on @sc->priority and the silbing and child memory cgroups will be skipped. The overall behaviour has been changed. This fixes the issue by applying the roundup to offlined memory cgroups only, to give more preference to reclaim memory from offlined memory cgroup. It sounds reasonable as those memory is unlikedly to be used by anyone. The issue was found by starting up 8 VMs on a Ampere Mustang machine, which has 8 CPUs and 16 GB memory. Each VM is given with 2 vCPUs and 2GB memory. It took 264 seconds for all VMs to be completely up and 784MB swap is consumed after that. With this patch applied, it took 236 seconds and 60MB swap to do same thing. So there is 10% performance improvement for my case. Note that KSM is disable while THP is enabled in the testing. total used free shared buff/cache available Mem: 16196 10065 2049 16 4081 3749 Swap: 8175 784 7391 total used free shared buff/cache available Mem: 16196 11324 3656 24 1215 2936 Swap: 8175 60 8115 Link: http://lkml.kernel.org/r/20200211024514.8730-1-gshan@redhat.com Fixes: 68600f62 ("mm: don't miss the last page because of round-off error") Signed-off-by:
Gavin Shan <gshan@redhat.com> Acked-by:
Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> [4.20+] Signed-off-by:
-
Alexandru Ardelean authored
There were a few attempts at changing behavior of the match_string() helpers (i.e. 'match_string()' & 'sysfs_match_string()'), to change & extend the behavior according to the doc-string. But the simplest approach is to just fix the doc-strings. The current behavior is fine as-is, and some bugs were introduced trying to fix it. As for extending the behavior, new helpers can always be introduced if needed. The match_string() helpers behave more like 'strncmp()' in the sense that they go up to n elements or until the first NULL element in the array of strings. This change updates the doc-strings with this info. Link: http://lkml.kernel.org/r/20200213072722.8249-1-alexandru.ardelean@analog.comSigned-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Acked-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Kees Cook <keescook@chromium.org> Cc: "Tobin C . Harding" <tobin@kernel.org> Signed-off-by:
-
Vasily Averin authored
for_each_mem_cgroup() increases css reference counter for memory cgroup and requires to use mem_cgroup_iter_break() if the walk is cancelled. Link: http://lkml.kernel.org/r/c98414fb-7e1f-da0f-867a-9340ec4bd30b@virtuozzo.com Fixes: 0a4465d3 ("mm, memcg: assign memcg-aware shrinkers bitmap to memcg") Signed-off-by:
Vasily Averin <vvs@virtuozzo.com> Acked-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by:
-
Christoph Hellwig authored
claim_swapfile now always takes i_rwsem. Link: http://lkml.kernel.org/r/20200114161225.309792-2-hch@lst.deSigned-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
-
Douglas Anderson authored
Recently, I found that get_maintainer was causing me to send emails to the old addresses for maintainers. Since I usually just trust the output of get_maintainer to know the right email address, I didn't even look carefully and fired off two patch series that went to the wrong place. Oops. The problem was introduced recently when trying to add signatures from Fixes. The problem was that these email addresses were added too early in the process of compiling our list of places to send. Things added to the list earlier are considered more canonical and when we later added maintainer entries we ended up deduplicating to the old address. Here are two examples using mainline commits (to make it easier to replicate) for the two maintainers that I messed up recently: $ git format-patch d8549bcd~..d8549bcd $ ./scripts/get_maintainer.pl 0001-clk-Add-clk_hw*.patch | grep Boyd Stephen Boyd <sboyd@codeaurora.org>... $ git format-patch 6d1238aa~..6d1238aa $ ./scripts/get_maintainer.pl 0001-arm64-dts-qcom-qcs404*.patch | grep Andy Andy Gross <andy.gross@linaro.org> Let's move the adding of addresses from Fixes: to the end since the email addresses from these are much more likely to be older. After this patch the above examples get the right addresses for the two examples. Link: http://lkml.kernel.org/r/20200127095001.1.I41fba9f33590bfd92cd01960161d8384268c6569@changeid Fixes: 2f5bd343 ("scripts/get_maintainer.pl: add signatures from Fixes: <badcommit> lines in commit message") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Acked-by:
Joe Perches <joe@perches.com> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Joe Perches authored
Commit 1ca84ed6 ("MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile") changed the use of the "P:" tag from "Person" to "Profile (ie: special subsystem coding styles and characteristics)" Change how get_maintainer.pl parses the "P:" tag to match. Link: http://lkml.kernel.org/r/ca53823fc5d25c0be32ad937d0207a0589c08643.camel@perches.comSigned-off-by:
Dan Williams <dan.j.william@intel.com> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by:
-
SeongJae Park authored
The commits introducing 'mlock-random-test'[1], 'map_fiex_noreplace'[2], and 'thuge-gen'[3] have not added those in the 'run_vmtests' script and thus the 'run_tests' command of kselftests doesn't run those. This commit adds those in the script. 'gup_benchmark' and 'transhuge-stress' are also not included in the 'run_vmtests', but this commit does not add those because those are for performance measurement rather than pass/fail tests. [1] commit 26b4224d ("selftests: expanding more mlock selftest") [2] commit 91cbacc3 ("tools/testing/selftests/vm/map_fixed_noreplace.c: add test for MAP_FIXED_NOREPLACE") [3] commit fcc1f2d5 ("selftests: add a test program for variable huge page sizes in mmap/shmget") Link: http://lkml.kernel.org/r/20200206085144.29126-1-sj38.park@gmail.comSigned-off-by:
SeongJae Park <sjpark@amazon.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Christian Borntraeger authored
QEMU has a funny new build error message when I use the upstream kernel headers: CC block/file-posix.o In file included from /home/cborntra/REPOS/qemu/include/qemu/timer.h:4, from /home/cborntra/REPOS/qemu/include/qemu/timed-average.h:29, from /home/cborntra/REPOS/qemu/include/block/accounting.h:28, from /home/cborntra/REPOS/qemu/include/block/block_int.h:27, from /home/cborntra/REPOS/qemu/block/file-posix.c:30: /usr/include/linux/swab.h: In function `__swab': /home/cborntra/REPOS/qemu/include/qemu/bitops.h:20:34: error: "sizeof" is not defined, evaluates to 0 [-Werror=undef] 20 | #define BITS_PER_LONG (sizeof (unsigned long) * BITS_PER_BYTE) | ^~~~~~ /home/cborntra/REPOS/qemu/include/qemu/bitops.h:20:41: error: missing binary operator before token "(" 20 | #define BITS_PER_LONG (sizeof (unsigned long) * BITS_PER_BYTE) | ^ cc1: all warnings being treated as errors make: *** [/home/cborntra/REPOS/qemu/rules.mak:69: block/file-posix.o] Error 1 rm tests/qemu-iotests/socket_scm_helper.o This was triggered by commit d5767057 ("uapi: rename ext2_swab() to swab() and share globally in swab.h"). That patch is doing #include <asm/bitsperlong.h> but it uses BITS_PER_LONG. The kernel file asm/bitsperlong.h provide only __BITS_PER_LONG. Let us use the __ variant in swap.h Link: http://lkml.kernel.org/r/20200213142147.17604-1-borntraeger@de.ibm.com Fixes: d5767057 ("uapi: rename ext2_swab() to swab() and share globally in swab.h") Signed-off-by:Christian Borntraeger <borntraeger@de.ibm.com> Cc: Yury Norov <yury.norov@gmail.com> Cc: Allison Randal <allison@lohutok.net> Cc: Joe Perches <joe@perches.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: William Breathitt Gray <vilhelm.gray@gmail.com> Cc: Torsten Hilbrich <torsten.hilbrich@secunet.com> Signed-off-by:
-
Ioanna Alifieraki authored
This reverts commit a9795584. Commit a9795584 ("ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()") removes a lock that is needed. This leads to a process looping infinitely in exit_sem() and can also lead to a crash. There is a reproducer available in [1] and with the commit reverted the issue does not reproduce anymore. Using the reproducer found in [1] is fairly easy to reach a point where one of the child processes is looping infinitely in exit_sem between for(;;) and if (semid == -1) block, while it's trying to free its last sem_undo structure which has already been freed by freeary(). Each sem_undo struct is on two lists: one per semaphore set (list_id) and one per process (list_proc). The list_id list tracks undos by semaphore set, and the list_proc by process. Undo structures are removed either by freeary() or by exit_sem(). The freeary function is invoked when the user invokes a syscall to remove a semaphore set. During this operation freeary() traverses the list_id associated with the semaphore set and removes the undo structures from both the list_id and list_proc lists. For this case, exit_sem() is called at process exit. Each process contains a struct sem_undo_list (referred to as "ulp") which contains the head for the list_proc list. When the process exits, exit_sem() traverses this list to remove each sem_undo struct. As in freeary(), whenever a sem_undo struct is removed from list_proc, it is also removed from the list_id list. Removing elements from list_id is safe for both exit_sem() and freeary() due to sem_lock(). Removing elements from list_proc is not safe; freeary() locks &un->ulp->lock when it performs list_del_rcu(&un->list_proc) but exit_sem() does not (locking was removed by commit a9795584 ("ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()"). This can result in the following situation while executing the reproducer [1] : Consider a child process in exit_sem() and the parent in freeary() (because of semctl(sid[i], NSEM, IPC_RMID)). - The list_proc for the child contains the last two undo structs A and B (the rest have been removed either by exit_sem() or freeary()). - The semid for A is 1 and semid for B is 2. - exit_sem() removes A and at the same time freeary() removes B. - Since A and B have different semid sem_lock() will acquire different locks for each process and both can proceed. The bug is that they remove A and B from the same list_proc at the same time because only freeary() acquires the ulp lock. When exit_sem() removes A it makes ulp->list_proc.next to point at B and at the same time freeary() removes B setting B->semid=-1. At the next iteration of for(;;) loop exit_sem() will try to remove B. The only way to break from for(;;) is for (&un->list_proc == &ulp->list_proc) to be true which is not. Then exit_sem() will check if B->semid=-1 which is and will continue looping in for(;;) until the memory for B is reallocated and the value at B->semid is changed. At that point, exit_sem() will crash attempting to unlink B from the lists (this can be easily triggered by running the reproducer [1] a second time). To prove this scenario instrumentation was added to keep information about each sem_undo (un) struct that is removed per process and per semaphore set (sma). CPU0 CPU1 [caller holds sem_lock(sma for A)] ... freeary() exit_sem() ... ... ... sem_lock(sma for B) spin_lock(A->ulp->lock) ... list_del_rcu(un_A->list_proc) list_del_rcu(un_B->list_proc) Undo structures A and B have different semid and sem_lock() operations proceed. However they belong to the same list_proc list and they are removed at the same time. This results into ulp->list_proc.next pointing to the address of B which is already removed. After reverting commit a9795584 ("ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()") the issue was no longer reproducible. [1] https://bugzilla.redhat.com/show_bug.cgi?id=1694779 Link: http://lkml.kernel.org/r/20191211191318.11860-1-ioanna-maria.alifieraki@canonical.com Fixes: a9795584 ("ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()") Signed-off-by:
Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com> Acked-by:
Manfred Spraul <manfred@colorfullife.com> Acked-by:
Herton R. Krzesinski <herton@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: <malat@debian.org> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Jay Vosburgh <jay.vosburgh@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Arnd Bergmann authored
There are no in-kernel users remaining, but there may still be users that include linux/time.h instead of sys/time.h from user space, so leave the types available to user space while hiding them from kernel space. Only the __kernel_old_* versions of these types remain now. Link: http://lkml.kernel.org/r/20200110154232.4104492-4-arnd@arndb.deSigned-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
No users remain, so kill these off before we grow new ones. Link: http://lkml.kernel.org/r/20200110154232.4104492-3-arnd@arndb.deSigned-off-by:
-
Arnd Bergmann authored
A couple of helpers are now obsolete and can be removed, so drivers can no longer start using them and instead use y2038-safe interfaces. Link: http://lkml.kernel.org/r/20200110154232.4104492-2-arnd@arndb.deSigned-off-by:
-
Rafael J. Wysocki authored
Commit fdde0ff8 ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") overlooked the fact that fixed events can wake up the system too and broke RTC wakeup from suspend-to-idle as a result. Fix this issue by checking the fixed events in acpi_s2idle_wake() in addition to checking wakeup GPEs and break out of the suspend-to-idle loop if the status bits of any enabled fixed events are set then. Fixes: fdde0ff8 ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") Reported-and-tested-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dave Airlie authored
Merge tag 'drm-intel-fixes-2020-02-20' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes drm/i915 fixes for v5.6-rc3: - Workaround missing Display Stream Compression (DSC) state readout by forcing modeset when its enabled at probe - Fix EHL port clock voltage level requirements - Fix queuing retire workers on the virtual engine - Fix use of partially initialized waiters - Stop using drm_pci_alloc/drm_pci/free - Fix rewind of RING_TAIL by forcing a context reload - Fix locking on resetting ring->head - Propagate our bug filing URL change to stable kernels Signed-off-by:
Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87y2sxtsrd.fsf@intel.com
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
drm-misc-fixes for v5.6-rc3: - Fix dt binding for sunxi. - Allow only 1 rotation argument, and allow 0 rotation in video cmdline. - Small compiler warning fix for panfrost. - Fix when using performance counters in panfrost when using per fd address space. Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: shutdown and kexec/kdump related fixes. 2 small patches to fix kexec shutdown and kdump kernel driver init issues. ==================== Signed-off-by: -
Vasundhara Volam authored
If crashed kernel does not shutdown the NIC properly, PCIe FLR is required in the kdump kernel in order to initialize all the functions properly. Fixes: d629522e ("bnxt_en: Reduce memory usage when running in kdump kernel.") Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
