- 17 Dec, 2013 23 commits
-
-
Imre Deak authored
Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Imre Deak authored
No functional change. Signed-off-by:
-
Ville Syrjälä authored
Apparently always enabling the sprite scaler magically made sprites work on ILK in the past. I think the real reason for the failure was missing sprite watermark programming, and enabling the scaler effectively disabled LP1+ watermarks, which was enough to keep things going. Or it might be that the hardware more or less ignores watermarks for scaled sprites since things seem to work even if I leave sprite watermarks at 0 and disable all other planes except the sprite. In any case, we left the scaler always on but then failed to check whether we might be exceeding the scaler's source size limits. That caused the sprite to fail when a sufficiently large unscaled image was being displayed. Now that we're getting proper watermark programming for ILK, we can keep the scaler disabled unless we need to do actual scaling. This reverts commit 8aaa81a1. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Ville Syrjälä authored
As the watermark registers aren't double bufferd, clearing the watermarks immediately after writing the sprite registers can be hazardous. Until we have something better, add a wait for vblank between the two steps to make sure the sprite no longer needs the watermark levels before we clear them. Signed-off-by:
-
Ville Syrjälä authored
When color keying is used, the primary may not be invisible even though the sprite fully covers it. So check for color keying before deciding to disable the primary plane. Signed-off-by:
-
Ville Syrjälä authored
We now have a very clear method of disabling LP1+ wartermarks, and we can actually detect if we actually did disable them, or if they were already disabled. Use that to clean up the WaCxSRDisabledForSpriteScaling:ivb handling. I was hoping to apply the workaround in a way that wouldn't require a blocking wait, but sadly IVB really does appear to require LP1+ watermarks to be off for an entire frame before enabling sprite scaling. Simply disabling LP1+ watermarks during the previous frame is not enough, no matter how early in the frame we do it :( Signed-off-by:
-
Ville Syrjälä authored
The new HSW watermark code can now handle ILK/SNB/IVB as well, so switch them over. Kill the old code. Signed-off-by:
-
Ville Syrjälä authored
ILK doesn't like if we just write the LP1+ watermarks registers with 0. We need to just disable the watermarks by clearing the enable bit. Use that method also when disabling LP1+ watermarks in init_clock_gating. It looks like disabling the sprite LP1 watermarks can cause underruns even if we just toggle the WM1S_LP_EN bit. So treat that bit like the actual watermark numbers and avoid setting it to 0 immediately. Signed-off-by:
-
Ville Syrjälä authored
Linetime watermarks don't exist on ILK/SNB/IVB, so don't compute them except on HSW. Signed-off-by:
-
Ville Syrjälä authored
ILK has a bunch of issues with FBC. First of all, BSpec tells us that FBC WM should never be enabled. Secondly when FBC is enabled with FBC WM disabled, LP2+ watermarks must be disabled. Signed-off-by:
-
Ville Syrjälä authored
Multi-pipe LP1+ watermarks are a HSW+ feature, so let's not do it on earlier generations. Signed-off-by:
-
Ville Syrjälä authored
On ILK disabling LP1+ watermarks must be done carefully to avoid underruns. If we just write 0 to the register in the middle of the scan cycle we often get an underrun. So instead we have to leave the actual watermark levels in the register intact, and just toggle the enable bit. Presumably the hardware takes a while to get out of low power mode, and so the watermark level need to stay valid until that time. We also have to be careful with the WM1S_LP_EN bit. It seems the hardware more or less treats it like the actual watermarks numbers, and so we must not toggle it too soon. Just leave it alone when disabling the LP1+ watermarks. Signed-off-by:
-
Ville Syrjälä authored
ILK/SNB don't have LP2+ watermarks for sprites. Also the LP1 sprite watermark register has its own enable bit. Take these differences into account when programming the LP1+ registers. Signed-off-by:
-
Ville Syrjälä authored
On ILK/SNB only LP0/1 watermarks can be enabled when sprites are enabled, and on ILK/SNB/IVB sprite scaling is limited to LP0 only. So we can avoid computing the extra levels we're never going to use. Signed-off-by:
-
Ville Syrjälä authored
Add a new function ilk_wm_lp_latency() which will tell us what to write into the WM_LPx register latency field. HSW is different from erlier gens in this regard. Signed-off-by:
-
Ville Syrjälä authored
On IVB the display data buffer partitioning control lives in the DISP_ARB_CTL2 register. Add the relevant defines/code for it. Signed-off-by:
-
Daniel Vetter authored
Otherwise we don't kick out firmware framebuffers like vesafb and efifb when CONFIG_DRM_I915_FBDEV=n but CONFIG_FB=y. There's still the pesky issue with vgacon which we should somehow replace with the dummy console at least. We have a similar issue at module un/reload, since vgacon state is terminally botched after i915.ko has loaded in modeset mode. But this gets us a step further at least. v2: Use IS_ENABLED - I always get this wrong for tristates. Spotted by Jani. Reported-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Damien Lespiau authored
Signed-off-by:
Damien Lespiau <damien.lespiau@intel.com> Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
-
Daniel Vetter authored
Noticed while reviewing a patch and couldn't resist the OCD. Reviewed-by:
-
Ben Widawsky authored
Aside from the fact that it leaves confusing dumps on error capture, it is entirely unnecessary, and potentially harmful in cases like BDW, where the instruction has changed. In reality (seemingly), this will have no behavioral impact. Signed-off-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Ben Widawsky authored
A few command were out of numerical order and had different spacing. Put them back in numerical order, with proper spacing. Signed-off-by:
-
Jesse Barnes authored
We only need to init the reg offset for DPIO once, but we need to reset DPIO at resume time and at init time. Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Jesse Barnes authored
Just add an early init since we may need to access DPIO regs early on. The init call in modeset_init_hw is also needed for the resume case, when we need to reset DPIO to keep things happy. v2: split reset and reg init v3: split patches (Daniel) Signed-off-by:
-
- 16 Dec, 2013 3 commits
-
-
Jani Nikula authored
The whole file is wrapped around in #if defined(CONFIG_DEBUG_FS) anyway, so skip the file at the build level already. Signed-off-by:
-
Wei Yongjun authored
In case of error, the function debugfs_create_file() returns NULL pointer not ERR_PTR() if debugfs is enabled. The IS_ERR() test in the return value check should be replaced with NULL test. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Jani Nikula authored
We don't actually do anything with the information yet, but parse and log what's in the VBT. Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by:
-
- 14 Dec, 2013 3 commits
-
-
Paulo Zanoni authored
Now that all the infrastructure is in place and all the tests from pm_pc8 pass, we can finally enable the feature. Signed-off-by:
-
Paulo Zanoni authored
So we'll get a fault when someone tries to access the mmap, then we'll wake up from D3. v2: - Rebase v3: - Use gtt active/inactive Testcase: igt/pm_pc8/gem-mmap-gtt Signed-off-by:
-
Paulo Zanoni authored
The hangcheck function requires the hardware to be working, and if we're suspending we're going to put the HW in D3 state. Signed-off-by:
-
- 13 Dec, 2013 4 commits
-
-
Ben Widawsky authored
WaVSRefCountFullforceMissDisable and WaDSRefCountFullforceMissDisable VS is a carry-over from HSW, and DS is likely not used by anyone yet. Cc: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by:
-
Ben Widawsky authored
I stumbled on to some unimplemented errata. To be honest, I am not really sure of the impact, just that the docs say to do. No w/a name for this one. v2: v1 was a stale thing which should have never seen the light of day. (Haihao) Cc: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by:
-
Ville Syrjälä authored
Not all registers need forcewake even if they're not shadowed. Add the missing check to gen8_writeX() to avoid needless forcewake usage when writing eg. display registers. v2: Use straight up <0x40000 check instead of NEEDS_FORCE_WAKE() Reviewed-by:
-
Ville Syrjälä authored
The BIOS or someone else might have done something bad and there might be old GT FIFO erros reported in GTFIFODBG. Clear those out in intel_uncore_early_sanitize() to make sure we don't mistake them for our problems. Signed-off-by:
-
- 12 Dec, 2013 7 commits
-
-
Mika Kuoppala authored
If test is running, irq_get was not called so we should gain balance by not doing irq_put "So the rule is: if you access unlocked values, you use ACCESS_ONCE(). You don't say "but it can't matter". Because you simply don't know." -- Linus v2: use local variable so it can't change during test (Chris) v3: update commit msg and use ACCESS_ONCE (Ville) Signed-off-by:
-
Ville Syrjälä authored
Don't touch DPFC_RECOMP_CTL on FBC2, use RMW to update the FBC_CONTROL on FBC1 to make it easier for people to experiment with different numbers. Also fix the interval mask for FBC1. v2: Rebased Reviewed-by:
-
Ville Syrjälä authored
All mobile gen2 and gen3 chipsets should have FBC1, and the code should now handle them all. So just set has_fbc=true for all such chipsets. Note that fbc is still disabled by default for now. Signed-off-by:
-
Ville Syrjälä authored
Gen2 and gen3 don't have the FBC_CONTROL2 register, so don't touch it. Signed-off-by:
-
Ville Syrjälä authored
On gen2 the compressed frame buffer pitch is specified in 32B units rather than the 64B units used on gen3+. Signed-off-by:
-
Paulo Zanoni authored
The first piece, intel_ddi_pll_select, finds a PLL and assigns it to the CRTC, but doesn't write any register. It can also fail in case it doesn't find a PLL. The second piece, intel_ddi_pll_enable, uses the information stored by intel_ddi_pll_select to actually enable the PLL by writing to its register. This function can't fail. We also have some refcount sanity checks here. The idea is that one day we'll remove all the functions that touch registers from haswell_crtc_mode_set to haswell_crtc_enable, so we'll call intel_ddi_pll_select at haswell_crtc_mode_set and then call intel_ddi_pll_enable at haswell_crtc_enable. Since I'm already touching this code, let's take care of this particular split today. v2: - Clock on the debug message is in KHz - Add missing POSTING_READ Signed-off-by: -
Mika Kuoppala authored
Commit 094f9a54 ("drm/i915: Fix __wait_seqno to use true infinite timeouts") added support for __wait_seqno to detect missing interrupts and go around them by polling. As there is also timeout detection in __wait_seqno, the polling and timeout detection were done with the same timer. When there has been missed interrupts and polling is needed, the timer is set to trigger in (now + 1) jiffies in future, instead of the caller specified timeout. Now when io_schedule() returns, we calculate the jiffies left to timeout using the timer expiration value. As the current jiffies is now bound to be always equal or greater than the expiration value, the timeout_jiffies will become zero or negative and we return -ETIME to caller even tho the timeout was never reached. Fix this by decoupling timeout calculation from timer expiration. v2: Commit message with some sense in it (Chris Wilson) v3: add parenthesis on timeout_expire calculation v4: don't read jiffies without timeout (Chris Wilson) Signed-off-by:
-
