- 05 Dec, 2019 40 commits
-
-
Alin Nastac authored
[ Upstream commit 82940599 ] Each media stream negotiation between 2 SIP peers will trigger creation of 4 different expectations (2 RTP and 2 RTCP): - INVITE will create expectations for the media packets sent by the called peer - reply to the INVITE will create expectations for media packets sent by the caller The dport used by these expectations usually match the ones selected by the SIP peers, but they might get translated due to conflicts with another expectation. When such event occur, it is important to do this translation in both directions, dport translation on the receiving path and sport translation on the sending path. This commit fixes the sport translation when the peer requiring it is also the one that starts the media stream. In this scenario, first media stream packet is forwarded from LAN to WAN and will rely on nf_nat_sip_expected() to do the necessary sport translation. However, the expectation matched by this packet does not contain the necessary information for doing SNAT, this data being stored in the paired expectation created by the sender's SIP message (INVITE or reply to it). Signed-off-by: Alin Nastac <alin.nastac@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Leon Romanovsky authored
[ Upstream commit 199fa087 ] The failure to create debugfs entry is unpleasant event, but not enough to abort drier initialization. Align the mlx5_core code to debugfs design and continue execution whenever debugfs_create_dir() successes or not. Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters") Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Martin Schiller authored
[ Upstream commit 9b4924da ] This patch is based on commit a86caa9b ("pinctrl: msm: fix gpio-hog related boot issues"). It fixes the issue that the gpio ranges needs to be defined before gpiochip_add(). Therefore, we also have to swap the order of registering the pinctrl driver and registering the gpio chip. You also have to add the "gpio-ranges" property to the pinctrl device node to get it finally working. Signed-off-by: Martin Schiller <ms@dev.tdt.de> Acked-by: John Crispin <john@phrozen.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Linus Walleij authored
[ Upstream commit a0752e9c ] Commit 21abf103 ("gpio: Pass a flag to gpiochip_request_own_desc()") started to pass an enum gpiod_flags but this file is not including the header file that defines that enum and the compiler spits: drivers/memory/omap-gpmc.c: In function 'gpmc_probe_generic_child': drivers/memory/omap-gpmc.c:2174:9: error: type of formal parameter 4 is incomplete 0); ^ Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: 21abf103 ("gpio: Pass a flag to gpiochip_request_own_desc()") Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nathan Chancellor authored
[ Upstream commit 8ba35b3a ] Clang warns: samples/vfio-mdev/mtty.c:592:39: warning: implicit conversion from 'int' to 'char' changes value from 162 to -94 [-Wconstant-conversion] *buf = UART_MSR_DSR | UART_MSR_DDSR | UART_MSR_DCD; ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~ 1 warning generated. Turns out that all uses of buf in this function ultimately end up stored or cast to an unsigned type. Just use u8, which has the same number of bits but can store this larger number so Clang no longer warns. Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Masami Hiramatsu authored
[ Upstream commit fe6e6561 ] Show x86-64 specific blacklisted symbols in debugfs. Since x86-64 prohibits probing on symbols which are in entry text, those should be shown. Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yonghong Song <yhs@fb.com> Link: http://lkml.kernel.org/r/154503488425.26176.17136784384033608516.stgit@devboxSigned-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Masami Hiramatsu authored
[ Upstream commit fb1a59fa ] Blacklist symbols in arch-defined probe-prohibited areas. With this change, user can see all symbols which are prohibited to probe in debugfs. All archtectures which have custom prohibit areas should define its own arch_populate_kprobe_blacklist() function, but unless that, all symbols marked __kprobes are blacklisted. Reported-by: Andrea Righi <righi.andrea@gmail.com> Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yonghong Song <yhs@fb.com> Link: http://lkml.kernel.org/r/154503485491.26176.15823229545155174796.stgit@devboxSigned-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Ross Lagerwall authored
[ Upstream commit 1669907e ] If pcistub_init_device fails, the release function will be called with dev_data set to NULL. Check it before using it to avoid a NULL pointer dereference. Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Andrea Righi authored
[ Upstream commit bf9445a3 ] Blacklist symbols in Xen probe-prohibited areas, so that user can see these prohibited symbols in debugfs. See also: a50480cb. Signed-off-by: Andrea Righi <righi.andrea@gmail.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Darwin Dingel authored
[ Upstream commit 6d7f677a ] When a serial port gets faulty or gets flooded with inputs, its interrupt handler starts to work double time to get the characters to the workqueue for the tty layer to handle them. When this busy time on the serial/tty subsystem happens during boot, where it is also busy on the userspace trying to initialise, some processes can continuously get preempted and will be on hold until the interrupts subside. The fix is to backoff on processing received characters for a specified amount of time when an input overrun is seen (received a new character before the previous one is processed). This only stops receive and will continue to transmit characters to serial port. After the backoff period is done, it receive will be re-enabled. This is optional and will only be enabled by setting 'overrun-throttle-ms' in the dts. Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nicolas Saenz Julienne authored
[ Upstream commit 85af74c4 ] We're getting a reference RPi's firmware node in order to be able to communicate with it's driver. We should decrease the reference count on the dt node after being done with it. Fixes: a98d90e7 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Pan Bian authored
[ Upstream commit 6e0856d3 ] The memory chunk allocated by hid_allocate_device() should be released by hid_destroy_device(), not kfree(). Fixes: 0b28cb4b("HID: intel-ish-hid: ISH HID client driver") Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Geert Uytterhoeven authored
[ Upstream commit 2e948218 ] When falling back to PIO, active_rx must be set to a different value than cookie_rx[i], else sci_dma_rx_find_active() will incorrectly find a match, leading to a NULL pointer dereference in rx_timer_fn() later. Use zero instead, which is the same value as after driver initialization. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Josef Bacik authored
[ Upstream commit 158ffa36 ] We use this number to figure out how many delayed refs to run, but __btrfs_run_delayed_refs really only checks every time we need a new delayed ref head, so we always run at least one ref head completely no matter what the number of items on it. Fix the accounting to only be adjusted when we add/remove a ref head. In addition to using this number to limit the number of delayed refs run, a future patch is also going to use it to calculate the amount of space required for delayed refs space reservation. Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Filipe Manana authored
[ Upstream commit 0e6ec385 ] We can have a lot freed extents during the life span of transaction, so the red black tree that keeps track of the ranges of each freed extent (fs_info->freed_extents[]) can get quite big. When finishing a transaction commit we find each range, process it (discard the extents, unpin them) and then remove it from the red black tree. We can use an extent state record as a cache when searching for a range, so that when we clean the range we can use the cached extent state we passed to the search function instead of iterating the red black tree again. Doing things as fast as possible when finishing a transaction (in state TRANS_STATE_UNBLOCKED) is convenient as it reduces the time we block another task that wants to commit the next transaction. So change clear_extent_dirty() to allow an optional extent state record to be passed as an argument, which will be passed down to __clear_extent_bit. Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Anand Jain authored
[ Upstream commit b47dda2e ] The device-replace needs to check the result code of the scrub workers in btrfs_dev_replace_cancel and distinguish if successful cancel operation and when the there was no operation running. If btrfs_scrub_cancel() fails, return BTRFS_IOCTL_DEV_REPLACE_RESULT_NOT_STARTED so that user can try to cancel the replace again. Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> [ update changelog ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Hans van Kranenburg authored
[ Upstream commit da612e31 ] RAID5 and RAID6 profile store one copy of the data, not 2 or 3. These values are not yet used anywhere so there's no change. Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nikolay Borisov authored
[ Upstream commit fc8a168a ] Before btrfs_map_bio submits all stripe bios it does a number of checks to ensure the device for every stripe is present. However, it doesn't do a DEV_STATE_MISSING check, instead this is relegated to the lower level btrfs_schedule_bio (in the async submission case, sync submission doesn't check DEV_STATE_MISSING at all). Additionally btrfs_schedule_bios does the duplicate device->bdev check which has already been performed in btrfs_map_bio. This patch moves the DEV_STATE_MISSING check in btrfs_map_bio and removes the duplicate device->bdev check. Doing so ensures that no bio cloning/submission happens for both async/sync requests in the face of missing device. This makes the async io submission path slightly shorter in terms of instruction count. No functional changes. Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Roger Quadros authored
[ Upstream commit 8dc7623b ] PHY model is being used on omap5 platforms even if port mode is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required or not based on PHY mode. If PHY is provided in device tree, it must be required. So, if devm_usb_get_phy_by_phandle() gives us an error code other than -ENODEV (no PHY) then error out. This fixes USB Ethernet on omap5-uevm if PHY happens to probe after EHCI thus causing a -EPROBE_DEFER. Cc: Johan Hovold <johan@kernel.org> Cc: Ladislav Michl <ladis@linux-mips.org> Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Boris Brezillon authored
[ Upstream commit 73277443 ] The opcodes used by the controller when doing batched page prog should be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the default NFC_REG_WCMD_SET value matches the one we set in the driver which explains why we didn't notice the problem. Fixes: 614049a8 ("mtd: nand: sunxi: add support for DMA assisted operations") Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Jerome Brunet authored
[ Upstream commit 18f92bc0 ] On errors, if we don't stop the descriptor chain, it may continue to run and raise IRQ after we have called mmc_request_done(). This is bad because we won't be able to get cmd anymore and properly deal with the IRQ. This patch makes sure the descriptor chain is stopped before calling mmc_request_done() Fixes: 79ed05e3 ("mmc: meson-gx: add support for descriptor chain mode") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Lepton Wu authored
[ Upstream commit 8236b08c ] The old code always starts from fixed port for VMADDR_PORT_ANY. Sometimes when VMM crashed, there is still orphaned vsock which is waiting for close timer, then it could cause connection time out for new started VM if they are trying to connect to same port with same guest cid since the new packets could hit that orphaned vsock. We could also fix this by doing more in vhost_vsock_reset_orphans, but any way, it should be better to start from a random local port instead of a fixed one. Signed-off-by: Lepton Wu <ytht.net@gmail.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Atul Gupta authored
[ Upstream commit 6422ccc5 ] listen fails when more than one tls capable device is registered. tls_hw_hash is called for each dev which loops again for each cdev_list causing listen failure. Hence call chtls_listen_start/stop for specific device than loop over all devices. Signed-off-by: Atul Gupta <atul.gupta@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Greg Kroah-Hartman authored
This reverts commit 7392aa08 which is commit 7671ce21 upstream. It should not have been selected for a stable kernel as it breaks the nVMX regression tests. Reported-by: Jack Wang <jack.wang.usish@gmail.com> Reported-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: Jim Mattson <jmattson@google.com> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
This reverts commit 9fe573d5 which is commit b7031fd4 upstream. It should not have been selected for a stable kernel as it breaks the nVMX regression tests. Reported-by: Jack Wang <jack.wang.usish@gmail.com> Reported-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Jim Mattson <jmattson@google.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: Jim Mattson <jmattson@google.com> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jim Mattson authored
[ Upstream commit 0023ef39 ] RDTSCP is supported in legacy mode as well as long mode. The IA32_TSC_AUX MSR should be set to the correct guest value before entering any guest that supports RDTSCP. Fixes: 4e47c7a6 ("KVM: VMX: Add instruction rdtscp support for guest") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Peter Shier <pshier@google.com> Reviewed-by: Marc Orr <marcorr@google.com> Reviewed-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Krzysztof Kozlowski authored
[ Upstream commit c5510b8d ] If CONFIG_GPOILIB is not set, the stub of gpio_to_desc() should return the same type of error as regular version: NULL. All the callers compare the return value of gpio_to_desc() against NULL, so returned ERR_PTR would be treated as non-error case leading to dereferencing of error value. Fixes: 79a9becd ("gpiolib: export descriptor-based GPIO interface") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Marek Vasut authored
[ Upstream commit 92f45ebe ] The PCAL_PINCTRL_MASK is too large. The extended register block on PCAL6524, which is the largest chip with this block, has the block limited to address range 0x40..0x7f. This is because the bit 7 in the command register is used for the Address Increment functionality. Trim the mask to 0x60 to match the datasheet and to prevent accidental overwrite of the AI bit. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Sara Sharon authored
[ Upstream commit 956343a6 ] command len is set too early in the code, since when building AMSDU, the size changes. This causes the byte count table to have the wrong size. Fixes: a0ec0169 ("iwlwifi: support new tx api") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Sara Sharon authored
[ Upstream commit 0916224e ] When removing the driver, the following flow can happen: 1. host command is in progress, for example at index 68. 2. RX interrupt is received with the response. 3. Before it is processed, the remove flow kicks in, and calls iwl_pcie_txq_unmap. The function cleans all DMA, and promotes the read pointer to 69. 4. RX thread proceeds with the processing, and is calling iwl_pcie_cmdq_reclaim, which will print this error: iwl_pcie_cmdq_reclaim: Read index for DMA queue txq id (0), index 4 is out of range [0-256] 69 69. Detect this situation, and avoid the print. Change it to warning while at it, to make such issues more noticeable in the future. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Avraham Stern authored
[ Upstream commit 7bc24682 ] When traffic load is not low or low latency is active, TCM schedules re-evaluation work so in case traffic stops TCM will detect that traffic load has become low or that low latency is no longer active. However, if TCM is paused when the re-evaluation work runs, it does not re-evaluate and the re-evaluation work is no longer scheduled. As a result, TCM will not indicate that low latency is no longer active or that traffic load is low when traffic stops. Fix this by forcing TCM re-evaluation when TCM is resumed in case low latency is active or traffic load is not low. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Luca Coelho authored
[ Upstream commit 64866e5d ] This function is only half-used by mvm (i.e. only the nvm_version part matters, since the calibration version is irrelevant), so it's pointless to export it from iwlwifi. If mvm uses this function, it has the additional complexity of setting the calib version to a bogus value on all cfg structs. To avoid this, move the function to dvm and make a simple comparison of the nvm_version in mvm instead. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Masahiro Yamada authored
[ Upstream commit 4722a3e6 ] This commit fixes some build issues. The first issue is the breakage of linux.bin.ub target since commit ece97f3a ("microblaze: Fix simpleImage format generation") because the addition of UIMAGE_{IN,OUT} affected it. make ARCH=microblaze CROSS_COMPILE=microblaze-linux- linux.bin.ub [ snip ] OBJCOPY arch/microblaze/boot/linux.bin UIMAGE arch/microblaze/boot/linux.bin.ub.ub /usr/bin/mkimage: Can't open arch/microblaze/boot/linux.bin.ub: No such file or directory make[1]: *** [arch/microblaze/boot/Makefile;14: arch/microblaze/boot/linux.bin.ub] Error 1 make: *** [arch/microblaze/Makefile;83: linux.bin.ub] Error 2 The second issue is the use of the "if_changed" multiple times for the same target. As commit 92a47286 ("x86/boot: Fix if_changed build flip/flop bug") pointed out, this never works properly. Moreover, generating multiple images as a side-effect is confusing. Let's split the build recipe for each image. simpleImage.<dt>*.unstrip is just a copy of vmlinux. simpleImage.<dt> and simpleImage.<dt>.ub are created in the same way as linux.bin and linux.bin.ub, respectively. I kept simpleImage.* recipes independent of linux.bin.* ones to not change the behavior. Lastly, this commit fixes "make ARCH=microblaze clean". Previously, it only cleaned up the unstrip image. Now, all the simpleImage files are cleaned. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Masahiro Yamada authored
[ Upstream commit 2e14f94c ] To prepare for more fixes, move this to arch/microblaze/Makefile. Otherwise, the same "... is ready" would be printed multiple times. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Masahiro Yamada authored
[ Upstream commit bafcc61d ] "make ARCH=microblaze help" mentions simpleImage.<dt>.unstrip, but it is not a real Make target. It does not work because Makefile assumes "system.unstrip" is the name of DT. $ make ARCH=microblaze CROSS_COMPILE=microblaze-linux- simpleImage.system.unstrip [ snip ] make[1]: *** No rule to make target 'arch/microblaze/boot/dts/system.unstrip.dtb', needed by 'arch/microblaze/boot/dts/system.dtb'. Stop. make: *** [Makefile;1060: arch/microblaze/boot/dts] Error 2 make: *** Waiting for unfinished jobs.... simpleImage.<dt> works like a phony target that generates multiple images. Reflect the real behavior. I removed the DT directory path information because it is already explained a few lines below. While I am here, I deleted the redundant *_defconfig explanation. The top-level Makefile caters to list available defconfig files: mmu_defconfig - Build for mmu nommu_defconfig - Build for nommu Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Pan Bian authored
[ Upstream commit e5420877 ] The UBI device reference is dropped but then the device is used as a parameter of ubi_err. The bug is introduced in changing ubi_err's behavior. The old ubi_err does not require a UBI device as its first parameter, but the new one does. Fixes: 32608703 ("UBI: Extend UBI layer debug/messaging capabilities") Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Pan Bian authored
[ Upstream commit b95f83ab ] The MTD device reference is dropped via put_mtd_device, however its field ->index is read and passed to ubi_msg. To fix this, the patch moves the reference dropping after calling ubi_msg. Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Gabor Juhos authored
[ Upstream commit d62e98ed ] When ubifs is build without the LZO compressor and no compressor is given the creation of the default file system will fail. before selection the LZO compressor check if it is present and if not fall back to the zlib or none. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Sagi Grimberg authored
[ Upstream commit 092ff052 ] free the controller discard_page correctly. Fixes: cb5b7262 ("nvme: provide fallback for discard alloc failure") Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Darrick J. Wong authored
[ Upstream commit 64bafd2f ] Since mkfs always formats the filesystem with the realtime bitmap and summary inodes immediately after the root directory, we should expect that both of them are present and loadable, even if there isn't a realtime volume attached. There's no reason to skip this if rbmino == NULLFSINO; in fact, this causes an immediate crash if the there /is/ a realtime volume and someone writes to it. Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Bill O'Donnell <billodo@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-