The serdes status bit does not work as intended for the 5717 A0.
This patch implements an alternative detection scheme that will only be
valid for A0 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some tg3 devices that require the driver to post new rx
buffers in smaller increments.  Commit
4361935a, "tg3: Consider
rx_std_prod_idx a hw mailbox" changed how the driver tracks the rx
producer ring updates, but it does not make any special considerations
for the above-mentioned devices.  For those devices, it is possible for
the driver to hit the special case path, which updates the hardware
mailbox register but skips updating the shadow software mailbox member.
If the special case path represents the final mailbox update for this
ISR iteration, the hardware and software mailbox values will be out of
sync.  Ultimately, this will cause the driver to use a stale mailbox
value on the next iteration, which will appear to the hardware as a
large rx buffer update.  Bad things ensue.

The fix is to update the software shadow mailbox member when the special
case path is taken.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 87668d35, titled "tg3: Don't
touch RCB nic addresses", tried to avoid assigning the nic address of
the standard producer ring.  Unfortunately, the default nic address is
not correct for the 5787, the 5755M, or the 57765.  This patch
reenables the old behavior and opts out of the assignment only
for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Tested-by: Chow Loong Jin <hyperair@ubuntu.com>
Tested-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO self-test should not be run on boards without an MDIO PHY,
such as SFN5122F-R3 and later revisions.  It should also not try to
address a specific MMD in an MDIO clause 22 PHY.  Check the
mode_support field to decide which mode to use, if any.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is down and we are using polled mode for MCDI
operations, we busy-wait for completion for approximately 1 jiffy
using udelay() and then back off to schedule().  But the completion
will not wake the task, since we are using polled mode!  We must use
schedule_timeout_uninterruptible() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes a delay in hardware after every received packet allowing
more time for transmitted packets to go out in between received packets in
half duplex.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A previous 82577 workaround that set the MDIO access speed to slow mode for
every PHY register read/write when the cable is unplugged should instead
set the access mode to always be slow before any PHY register access.
Since the mode bit gets cleared when the PHY is reset, set the mode after
every PHY reset.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves issues seen when running netconsole and rebooting via
reboot -f.  The issue was due to the fact that we were attempting to
perform interrupt actions when the q_vectors and rings had already been
freed via the ixgbe_shutdown routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During TX timeout procedure dev could be awoken too early, e.g. by
sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame()
can run while buffers are freed causing an oops. This patch fixes it
by adding netif_device_present() test in sky2_tx_complete().

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925

With debugging by: Mike McCormack <mikem@ring3k.org>
Reported-by: Berck E. Nash <flyboy@gmail.com>
Tested-by: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_CFG80211_WEXT is not set, there is
a refcount imbalance with rdev->opencount, fix
that by moving it out of the ifdef.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When ieee80211_monitor_select_queue encounters data frames, it selects
the WMM AC based on skb->priority and assumes that skb->priority
contains a valid 802.1d tag. However this assumption is incorrect, since
ieee80211_select_queue has not been called at this point.
If skb->priority > 7, an array overrun occurs, which could lead to
invalid values, resulting in crashes in the tx path.
Fix this by setting skb->priority based on the 802.11 header for QoS
frames and using the default AC for all non-QoS frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

3c509 was changed to support ethtool in 2002, making the 'xcvr' module
parameter obsolete in most cases.  More recently 3c509 was converted
to the modern driver model and this parameter was removed.  Fix the
documentation to refer to ethtool rather than the module parameter.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

tpacket_snd() can change and kfree an skb after dev_queue_xmit(),
which is illegal.

With debugging by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Michael Breuer <mbreuer@majjas.com>
With help from: David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Michael Breuer<mbreuer@majjas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Smatch (and presumably other static checkers) complain that MAX_TID_COUNT is
past the end of the array.  In the resulting discussion, Zhu Yi pointed out
that this value is not used in real life and the assignment was only there to
silence a gcc warning.

If there were a bug in the surrounding code and the value were used, the
WARN_ON(!qc) would print a warning before the crash.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

pci_dma_mapping_error should be used to test return value of
pci_map_single or pci_map_page.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On beacon change update notification from mac we are not disabling
the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when
station leaves IBSS. Driver should indicate uCode to not to send
anything on receiving this notification.

Functionality to indicate uCode is duplicated across
two notifications so created a common function called iwl_set_no_assoc.

Fix the issue at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When txq read_ptr equals to write_ptr, iwl_queue_used should
always return false. Because there is no used TFD in this case.

This is a complementary fix to the fix already included in commit "iwl3945:
fix panic in iwl3945 driver". Both fixes are needed to address the panic
below.

This problem was discussed on linux-wireless in
http://thread.gmane.org/gmane.linux.kernel.wireless.general/43568

<1>[ 7290.414172] IP: [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.414205] PGD 0
<1>[ 7290.414214] Thread overran stack, or stack corrupted
<0>[ 7290.414229] Oops: 0002 [#1] PREEMPT SMP
<0>[ 7290.414246] last sysfs file: /sys/devices/platform/coretemp.1/temp1_input
<4>[ 7290.414265] CPU 0
<4>[ 7290.414274] Modules linked in: af_packet nfsd usb_storage usb_libusual cpufreq_powersave exportfs cpufreq_conservative iwl3945 nfs cpufreq_userspace snd_hda_codec_realtek acpi_cpufreq uvcvideo lockd iwlcore snd_hda_intel joydev coretemp nfs_acl videodev snd_hda_codec mac80211 v4l1_compat snd_hwdep sbp2 v4l2_compat_ioctl32 uhci_hcd psmouse auth_rpcgss ohci1394 cfg80211 ehci_hcd video ieee1394 snd_pcm serio_raw battery ac nvidia(P) usbcore output sunrpc evdev lirc_ene0100 snd_page_alloc rfkill tg3 libphy fuse lzo lzo_decompress lzo_compress
<6>[ 7290.414486] Pid: 0, comm: swapper Tainted: P           2.6.32-rc8-wl #213 Aspire 5720
<6>[ 7290.414507] RIP: 0010:[<ffffffffa0dd53a1>]  [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<6>[ 7290.414541] RSP: 0018:ffff880002203d60  EFLAGS: 00010246
<6>[ 7290.414557] RAX: 000000000000004f RBX: ffff880064c11600 RCX: 0000000000000013
<6>[ 7290.414576] RDX: ffffffffa0ddcf20 RSI: ffff8800512b7008 RDI: 0000000000000038
<6>[ 7290.414596] RBP: ffff880002203dd0 R08: 0000000000000000 R09: 0000000000000100
<6>[ 7290.414616] R10: 0000000000000001 R11: 0000000000000000 R12: 00000000000000a0
<6>[ 7290.414635] R13: 0000000000000002 R14: 0000000000000013 R15: 0000000000020201
<6>[ 7290.414655] FS:  0000000000000000(0000) GS:ffff880002200000(0000) knlGS:0000000000000000
<6>[ 7290.414677] CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
<6>[ 7290.414693] CR2: 0000000000000041 CR3: 0000000001001000 CR4: 00000000000006f0
<6>[ 7290.414712] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<6>[ 7290.414732] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>[ 7290.414752] Process swapper (pid: 0, threadinfo ffffffff81524000, task ffffffff81528b60)
<0>[ 7290.414772] Stack:
<4>[ 7290.414780]  ffff880002203da0 0000000000000046 0000000000000000 0000000000000046
<4>[ 7290.414804] <0> 0000000000000282 0000000000000282 0000000000000282 ffff880064c12010
<4>[ 7290.414830] <0> ffff880002203db0 ffff880064c11600 ffff880064c12e50 ffff8800512b7000
<0>[ 7290.414858] Call Trace:
<0>[ 7290.414867]  <IRQ>
<4>[ 7290.414884]  [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945]
<4>[ 7290.414910]  [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60
<4>[ 7290.414931]  [<ffffffff81049a21>] tasklet_action+0x101/0x110
<4>[ 7290.414950]  [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160
<4>[ 7290.414968]  [<ffffffff8100d01c>] call_softirq+0x1c/0x30
<4>[ 7290.414986]  [<ffffffff8100eff5>] do_softirq+0x75/0xb0
<4>[ 7290.415003]  [<ffffffff81049ee5>] irq_exit+0x95/0xa0
<4>[ 7290.415020]  [<ffffffff8100e547>] do_IRQ+0x77/0xf0
<4>[ 7290.415038]  [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf
<0>[ 7290.415052]  <EOI>
<4>[ 7290.415067]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415087]  [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5
<4>[ 7290.415107]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415130]  [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0
<4>[ 7290.415149]  [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110
<4>[ 7290.415168]  [<ffffffff8137b3d5>] ? rest_init+0x75/0x80
<4>[ 7290.415187]  [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3
<4>[ 7290.415206]  [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129
<4>[ 7290.415227]  [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb
<0>[ 7290.415243] Code: 00 41 39 ce 0f 8d e8 01 00 00 48 8b 47 40 48 63 d2 48 69 d2 98 00 00 00 4c 8b 04 02 48 c7 c2 20 cf dd a0 49 8d 78 38 49 8d 40 4f <c6> 47 09 00 c6 47 0c 00 c6 47 0f 00 c6 47 12 00 c6 47 15 00 49
<1>[ 7290.415382] RIP  [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.415410]  RSP <ffff880002203d60>
<0>[ 7290.415421] CR2: 0000000000000041
<4>[ 7290.415436] ---[ end trace ec46807277caa515 ]---
<0>[ 7290.415450] Kernel panic - not syncing: Fatal exception in interrupt
<4>[ 7290.415468] Pid: 0, comm: swapper Tainted: P      D    2.6.32-rc8-wl #213
<4>[ 7290.415486] Call Trace:
<4>[ 7290.415495]  <IRQ>  [<ffffffff8138c040>] panic+0x7d/0x13a
<4>[ 7290.415519]  [<ffffffff8101071a>] oops_end+0xda/0xe0
<4>[ 7290.415538]  [<ffffffff8102e1ea>] no_context+0xea/0x250
<4>[ 7290.415557]  [<ffffffff81038991>] ? select_task_rq_fair+0x511/0x780
<4>[ 7290.415578]  [<ffffffff8102e475>] __bad_area_nosemaphore+0x125/0x1e0
<4>[ 7290.415597]  [<ffffffff81038d0c>] ? __enqueue_entity+0x7c/0x80
<4>[ 7290.415616]  [<ffffffff81039201>] ? enqueue_task_fair+0x111/0x150
<4>[ 7290.415636]  [<ffffffff8102e53e>] bad_area_nosemaphore+0xe/0x10
<4>[ 7290.415656]  [<ffffffff8102e8fa>] do_page_fault+0x26a/0x320
<4>[ 7290.415674]  [<ffffffff813905df>] page_fault+0x1f/0x30
<4>[ 7290.415697]  [<ffffffffa0dd53a1>] ? iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.415723]  [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945]
<4>[ 7290.415746]  [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60
<4>[ 7290.415764]  [<ffffffff81049a21>] tasklet_action+0x101/0x110
<4>[ 7290.415783]  [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160
<4>[ 7290.415801]  [<ffffffff8100d01c>] call_softirq+0x1c/0x30
<4>[ 7290.415818]  [<ffffffff8100eff5>] do_softirq+0x75/0xb0
<4>[ 7290.415835]  [<ffffffff81049ee5>] irq_exit+0x95/0xa0
<4>[ 7290.415852]  [<ffffffff8100e547>] do_IRQ+0x77/0xf0
<4>[ 7290.415869]  [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf
<4>[ 7290.415883]  <EOI>  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415911]  [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5
<4>[ 7290.415931]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415952]  [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0
<4>[ 7290.415971]  [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110
<4>[ 7290.415989]  [<ffffffff8137b3d5>] ? rest_init+0x75/0x80
<4>[ 7290.416007]  [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3
<4>[ 7290.416026]  [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129
<4>[ 7290.416047]  [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I forgot to convert the radiotap length to
CPU endian, which sparse found thankfully.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Various missing sanity checks caused rejected action frames to be
interpreted as channel switch announcements, which can cause a client
mode interface to switch away from its operating channel, thereby losing
connectivity. This patch ensures that only spectrum management action
frames are processed by the CSA handling function and prevents rejected
action frames from getting processed by the MLME code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 'mac80211: fix skb buffering issue' added an ->ndo_select_queue()
for monitor interfaces which can end up dereferencing ieee802_1d_to_ac[]
beyond the end of the array for injected data packets (as skb->priority
isn't guaranteed to be zero or within [0:7]), which then triggers the
WARN_ON in net/core/dev.c:dev_cap_txqueue().  Fix this by always setting
the priority to zero on injected data frames.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

normal users are currently allowed to set/modify ebtables rules.
Restrict it to processes with CAP_NET_ADMIN.

Note that this cannot be reproduced with unmodified ebtables binary
because it uses SOCK_RAW.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

Fix e1000e_rar_set() to flush consecutive register writes to avoid write
combining which some parts cannot handle.  Update e1000e_init_rx_addrs()
to call the fixed e1000e_rar_set() instead of duplicating code.

Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC
address is all zeros.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e_enable_tx_pkt_filtering() will return a non-zero value if the
driver fails to enable the manageability interface on the host for
any reason; instead it should retun zero to indicate filtering has been
disabled.  Also provide a single exit point for the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adaptive IFS which involves writing to the Adaptive IFS Throttle register
was being done for all devices supported by the driver even though it is
not supported (i.e. the register doesn't even exist) on some devices.  The
feature is supported on 8257x/82583 and ICH/PCH based devices, but not
on ESB2.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a change in pci_restore_state()[1] which clears the saved_state
flag, the driver should call pci_save_state() to set the flag once again
to avoid issues with EEH (same fix that recently was submitted for ixgbe).

[1] commmit 4b77b0a2Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o If tx and rx resources are not available, during set mac request.
  Then this request wont be passed to firmware and it will be added to
  driver mac list and will never make it to firmware.
  So if resources are not available, don't add it to driver mac list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Fix pointless assignments
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o While unloading driver or resetting the context, tx ring was not
  getting free.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a netstamp_needed accounting issue when the listen socket
has SO_TIMESTAMP set:

    s = socket(AF_INET, SOCK_STREAM, 0);
    setsockopt(s, SOL_SOCKET, SO_TIMESTAMP, 1); -> netstamp_needed = 1
    bind(s, ...);
    listen(s, ...);
    s2 = accept(s, ...); -> netstamp_needed = 1
    close(s2); -> netstamp_needed = 0
    close(s); -> netstamp_needed = -1
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the driver probe function the emac module clock needs to
be enabled before calling register_netdev(). As soon as the
device is registered the driver get_stats function can be invoked
by the core - the module clock must be switched on to be able to
read from stats registers. Also explicitly call matching clk_disable
for failure conditions in probe function.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver).  There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids.  However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc is still throwing a warning that is could be used
uninitialized.  This fixes it, and properly formats the device ID
checks for the use of this variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As noticed by Dan Carpenter <error27@gmail.com>, update_nl_seq()
currently contains an out of bounds read of the seq_aft_nl array
when looking for the oldest sequence number position.

Fix it to only compare valid positions.

Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.

These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.

This problem was introduced in commit 7fd96ce4 ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stanse found a memory leak in atl2_get_eeprom. eeprom_buff is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: atl1-devel@lists.sourceforge.net
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>