- 22 Oct, 2015 40 commits
-
-
Roger Quadros authored
commit e5bfeab0 upstream. For whatever reason if XHCI died in the previous instant then it will never recover on the next xhci_start unless we clear the DYING flag. Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
commit cbb4be65 upstream. Fix potential null-pointer dereference at probe by making sure that the required endpoints are present. The whiteheat driver assumes there are at least five pairs of bulk endpoints, of which the final pair is used for the "command port". An attempt to bind to an interface with fewer bulk endpoints would currently lead to an oops. Fixes CVE-2015-5257. Reported-by:
Moein Ghasemzadeh <moein@istuary.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Daniel Vetter authored
commit da168d81 upstream. I've done some extensive history digging across libdrm, mesa and xf86-video-{intel,nouveau,ati}. The only potential user of this with kms drivers I could find was ttmtest, which once used drmGetLock still. But that mistake was quickly fixed up. Even the intel xvmc library (which otherwise was really good with using dri1 stuff in kms mode) managed to never take the hw lock for dri2 (and hence kms). Hence it should be save to unconditionally disallow this. Cc: Peter Antoine <peter.antoine@intel.com> Reviewed-by:
Peter Antoine <peter.antoine@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
-
Fabiano Fidêncio authored
commit 8d0d9401 upstream. When disabling/enabling a crtc the primary area must be updated independently of which crtc has been disabled/enabled. Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1264735Signed-off-by:
Fabiano Fidêncio <fidencio@redhat.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Dave Airlie authored
commit 69e5d3f8 upstream. If the server isn't new enough to give us state, report the first monitor as always connected, otherwise believe the server side. Signed-off-by:
-
Steve French authored
commit e0ddde9d upstream. leases (oplocks) were always requested for SMB2/SMB3 even when oplocks disabled in the cifs.ko module. Signed-off-by:
Steve French <steve.french@primarydata.com> Reviewed-by:
Chandrika Srinivasan <chandrika.srinivasan@citrix.com> Signed-off-by:
-
Pablo Neira Ayuso authored
commit ba378ca9 upstream. Fix lookup of existing match/target structures in the corresponding list by skipping the family check if NFPROTO_UNSPEC is used. This is resulting in the allocation and insertion of one match/target structure for each use of them. So this not only bloats memory consumption but also severely affects the time to reload the ruleset from the iptables-compat utility. After this patch, iptables-compat-restore and iptables-compat take almost the same time to reload large rulesets. Fixes: 0ca743a5 ("netfilter: nf_tables: add compatibility layer for x_tables") Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Pablo Neira Ayuso authored
commit 95dd8653 upstream. We have to put back the references to the master conntrack and the expectation that we just created, otherwise we'll leak them. Fixes: 0ef71ee1 ("netfilter: ctnetlink: refactor ctnetlink_create_expect") Reported-by:
Tim Wiess <Tim.Wiess@watchguard.com> Signed-off-by:
-
Joe Stringer authored
commit 4b31814d upstream. When zones were originally introduced, the expectation functions were all extended to perform lookup using the zone. However, insertion was not modified to check the zone. This means that two expectations which are intended to apply for different connections that have the same tuple but exist in different zones cannot both be tracked. Fixes: 5d0aa2cc (netfilter: nf_conntrack: add support for "conntrack zones") Signed-off-by:
Joe Stringer <joestringer@nicira.com> Signed-off-by:
-
Mikulas Patocka authored
commit 042745ee upstream. Commit 3a0f9aae ("dm raid: round region_size to power of two") intended to make sure that the default region size is a power of two. However, the logic in that commit is incorrect and sets the variable region_size to 0 or 1, depending on whether min_region_size is a power of two. Fix this logic, using roundup_pow_of_two(), so that region_size is properly rounded up to the next power of two. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Fixes: 3a0f9aae ("dm raid: round region_size to power of two") Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Liu.Zhao authored
commit 19ab6bc5 upstream. This is intended to add ZTE device PIDs on kernel. Signed-off-by:
Liu.Zhao <lzsos369@163.com> [johan: sort the new entries ] Signed-off-by:
-
Shawn Lin authored
commit 6fa92e2b upstream. we found this issue but still exit in lastest kernel. Simply keep ion_handle_create under mutex_lock to avoid this race. WARNING: CPU: 2 PID: 2648 at drivers/staging/android/ion/ion.c:512 ion_handle_add+0xb4/0xc0() ion_handle_add: buffer already found. Modules linked in: iwlmvm iwlwifi mac80211 cfg80211 compat CPU: 2 PID: 2648 Comm: TimedEventQueue Tainted: G W 3.14.0 #7 00000000 00000000 9a3efd2c 80faf273 9a3efd6c 9a3efd5c 80935dc9 811d7fd3 9a3efd88 00000a58 812208a0 00000200 80e128d4 80e128d4 8d4ae00c a8cd8600 a8cd8094 9a3efd74 80935e0e 00000009 9a3efd6c 811d7fd3 9a3efd88 9a3efd9c Call Trace: [<80faf273>] dump_stack+0x48/0x69 [<80935dc9>] warn_slowpath_common+0x79/0x90 [<80e128d4>] ? ion_handle_add+0xb4/0xc0 [<80e128d4>] ? ion_handle_add+0xb4/0xc0 [<80935e0e>] warn_slowpath_fmt+0x2e/0x30 [<80e128d4>] ion_handle_add+0xb4/0xc0 [<80e144cc>] ion_import_dma_buf+0x8c/0x110 [<80c517c4>] reg_init+0x364/0x7d0 [<80993363>] ? futex_wait+0x123/0x210 [<80992e0e>] ? get_futex_key+0x16e/0x1e0 [<8099308f>] ? futex_wake+0x5f/0x120 [<80c51e19>] vpu_service_ioctl+0x1e9/0x500 [<80994aec>] ? do_futex+0xec/0x8e0 [<80971080>] ? prepare_to_wait_event+0xc0/0xc0 [<80c51c30>] ? reg_init+0x7d0/0x7d0 [<80a22562>] do_vfs_ioctl+0x2d2/0x4c0 [<80b198ad>] ? inode_has_perm.isra.41+0x2d/0x40 [<80b199cf>] ? file_has_perm+0x7f/0x90 [<80b1a5f7>] ? selinux_file_ioctl+0x47/0xf0 [<80a227a8>] SyS_ioctl+0x58/0x80 [<80fb45e8>] syscall_call+0x7/0x7 [<80fb0000>] ? mmc_do_calc_max_discard+0xab/0xe4 Fixes: 83271f62 ("ion: hold reference to handle...") Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit b0dc3c8b upstream. When using nested btrees, the top leaves of the top levels contain block addresses for the root of the next tree down. If we shadow a shared leaf node the leaf values (sub tree roots) should be incremented accordingly. This is only an issue if there is metadata sharing in the top levels. Which only occurs if metadata snapshots are being used (as is possible with dm-thinp). And could result in a block from the thinp metadata snap being reused early, thus corrupting the thinp metadata snap. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Filipe Manana authored
commit 808f80b4 upstream. My previous fix in commit 005efedf ("Btrfs: fix read corruption of compressed and shared extents") was effective only if the compressed extents cover a file range with a length that is not a multiple of 16 pages. That's because the detection of when we reached a different range of the file that shares the same compressed extent as the previously processed range was done at extent_io.c:__do_contiguous_readpages(), which covers subranges with a length up to 16 pages, because extent_readpages() groups the pages in clusters no larger than 16 pages. So fix this by tracking the start of the previously processed file range's extent map at extent_readpages(). The following test case for fstests reproduces the issue: seq=`basename $0` seqres=$RESULT_DIR/$seq echo "QA output created by $seq" tmp=/tmp/$$ status=1 # failure is the default! trap "_cleanup; exit \$status" 0 1 2 3 15 _cleanup() { rm -f $tmp.* } # get standard environment, filters and checks . ./common/rc . ./common/filter # real QA test starts here _need_to_be_root _supported_fs btrfs _supported_os Linux _require_scratch _require_cloner rm -f $seqres.full test_clone_and_read_compressed_extent() { local mount_opts=$1 _scratch_mkfs >>$seqres.full 2>&1 _scratch_mount $mount_opts # Create our test file with a single extent of 64Kb that is going to # be compressed no matter which compression algo is used (zlib/lzo). $XFS_IO_PROG -f -c "pwrite -S 0xaa 0K 64K" \ $SCRATCH_MNT/foo | _filter_xfs_io # Now clone the compressed extent into an adjacent file offset. $CLONER_PROG -s 0 -d $((64 * 1024)) -l $((64 * 1024)) \ $SCRATCH_MNT/foo $SCRATCH_MNT/foo echo "File digest before unmount:" md5sum $SCRATCH_MNT/foo | _filter_scratch # Remount the fs or clear the page cache to trigger the bug in # btrfs. Because the extent has an uncompressed length that is a # multiple of 16 pages, all the pages belonging to the second range # of the file (64K to 128K), which points to the same extent as the # first range (0K to 64K), had their contents full of zeroes instead # of the byte 0xaa. This was a bug exclusively in the read path of # compressed extents, the correct data was stored on disk, btrfs # just failed to fill in the pages correctly. _scratch_remount echo "File digest after remount:" # Must match the digest we got before. md5sum $SCRATCH_MNT/foo | _filter_scratch } echo -e "\nTesting with zlib compression..." test_clone_and_read_compressed_extent "-o compress=zlib" _scratch_unmount echo -e "\nTesting with lzo compression..." test_clone_and_read_compressed_extent "-o compress=lzo" status=0 exit Signed-off-by:
Filipe Manana <fdmanana@suse.com> Tested-by:
Timofey Titovets <nefelim4ag@gmail.com> Signed-off-by:
-
Filipe Manana authored
commit 005efedf upstream. If a file has a range pointing to a compressed extent, followed by another range that points to the same compressed extent and a read operation attempts to read both ranges (either completely or part of them), the pages that correspond to the second range are incorrectly filled with zeroes. Consider the following example: File layout [0 - 8K] [8K - 24K] | | | | points to extent X, points to extent X, offset 4K, length of 8K offset 0, length 16K [extent X, compressed length = 4K uncompressed length = 16K] If a readpages() call spans the 2 ranges, a single bio to read the extent is submitted - extent_io.c:submit_extent_page() would only create a new bio to cover the second range pointing to the extent if the extent it points to had a different logical address than the extent associated with the first range. This has a consequence of the compressed read end io handler (compression.c:end_compressed_bio_read()) finish once the extent is decompressed into the pages covering the first range, leaving the remaining pages (belonging to the second range) filled with zeroes (done by compression.c:btrfs_clear_biovec_end()). So fix this by submitting the current bio whenever we find a range pointing to a compressed extent that was preceded by a range with a different extent map. This is the simplest solution for this corner case. Making the end io callback populate both ranges (or more, if we have multiple pointing to the same extent) is a much more complex solution since each bio is tightly coupled with a single extent map and the extent maps associated to the ranges pointing to the shared extent can have different offsets and lengths. The following test case for fstests triggers the issue: seq=`basename $0` seqres=$RESULT_DIR/$seq echo "QA output created by $seq" tmp=/tmp/$$ status=1 # failure is the default! trap "_cleanup; exit \$status" 0 1 2 3 15 _cleanup() { rm -f $tmp.* } # get standard environment, filters and checks . ./common/rc . ./common/filter # real QA test starts here _need_to_be_root _supported_fs btrfs _supported_os Linux _require_scratch _require_cloner rm -f $seqres.full test_clone_and_read_compressed_extent() { local mount_opts=$1 _scratch_mkfs >>$seqres.full 2>&1 _scratch_mount $mount_opts # Create a test file with a single extent that is compressed (the # data we write into it is highly compressible no matter which # compression algorithm is used, zlib or lzo). $XFS_IO_PROG -f -c "pwrite -S 0xaa 0K 4K" \ -c "pwrite -S 0xbb 4K 8K" \ -c "pwrite -S 0xcc 12K 4K" \ $SCRATCH_MNT/foo | _filter_xfs_io # Now clone our extent into an adjacent offset. $CLONER_PROG -s $((4 * 1024)) -d $((16 * 1024)) -l $((8 * 1024)) \ $SCRATCH_MNT/foo $SCRATCH_MNT/foo # Same as before but for this file we clone the extent into a lower # file offset. $XFS_IO_PROG -f -c "pwrite -S 0xaa 8K 4K" \ -c "pwrite -S 0xbb 12K 8K" \ -c "pwrite -S 0xcc 20K 4K" \ $SCRATCH_MNT/bar | _filter_xfs_io $CLONER_PROG -s $((12 * 1024)) -d 0 -l $((8 * 1024)) \ $SCRATCH_MNT/bar $SCRATCH_MNT/bar echo "File digests before unmounting filesystem:" md5sum $SCRATCH_MNT/foo | _filter_scratch md5sum $SCRATCH_MNT/bar | _filter_scratch # Evicting the inode or clearing the page cache before reading # again the file would also trigger the bug - reads were returning # all bytes in the range corresponding to the second reference to # the extent with a value of 0, but the correct data was persisted # (it was a bug exclusively in the read path). The issue happened # only if the same readpages() call targeted pages belonging to the # first and second ranges that point to the same compressed extent. _scratch_remount echo "File digests after mounting filesystem again:" # Must match the same digests we got before. md5sum $SCRATCH_MNT/foo | _filter_scratch md5sum $SCRATCH_MNT/bar | _filter_scratch } echo -e "\nTesting with zlib compression..." test_clone_and_read_compressed_extent "-o compress=zlib" _scratch_unmount echo -e "\nTesting with lzo compression..." test_clone_and_read_compressed_extent "-o compress=lzo" status=0 exit Signed-off-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
-
Jeff Mahoney authored
commit a30e577c upstream. In btrfs_evict_inode, we properly truncate the page cache for evicted inodes but then we call btrfs_wait_ordered_range for every inode as well. It's the right thing to do for regular files but results in incorrect behavior for device inodes for block devices. filemap_fdatawrite_range gets called with inode->i_mapping which gets resolved to the block device inode before getting passed to wbc_attach_fdatawrite_inode and ultimately to inode_to_bdi. What happens next depends on whether there's an open file handle associated with the inode. If there is, we write to the block device, which is unexpected behavior. If there isn't, we through normally and inode->i_data is used. We can also end up racing against open/close which can result in crashes when i_mapping points to a block device inode that has been closed. Since there can't be any page cache associated with special file inodes, it's safe to skip the btrfs_wait_ordered_range call entirely and avoid the problem. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100911Tested-by:
Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Reviewed-by:
-
Yitian Bu authored
commit 4873867e upstream. from Designware I2S datasheet, tx/rx XRUN irq is cleared by reading register TOR/ROR, rather than by writing into them. Signed-off-by:
Yitian Bu <yitian.bu@tangramtek.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Robert Jarzmik authored
commit 3c8f7710 upstream. The previous fix of pxa library support, which was introduced to fix the library dependency, broke the previous SoC behavior, where a machine code binding pxa2xx-ac97 with a coded relied on : - sound/soc/pxa/pxa2xx-ac97.c - sound/soc/codecs/XXX.c For example, the mioa701_wm9713.c machine code is currently broken. The "select ARM" statement wrongly selects the soc/arm/pxa2xx-ac97 for compilation, as per an unfortunate fate SND_PXA2XX_AC97 is both declared in sound/arm/Kconfig and sound/soc/pxa/Kconfig. Fix this by ensuring that SND_PXA2XX_SOC correctly triggers the correct pxa2xx-ac97 compilation. Fixes: 846172df ("ASoC: fix SND_PXA2XX_LIB Kconfig warning") Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Robert Jarzmik authored
commit 8811191f upstream. PCM receive and transmit DMA requestor lines were reverted, breaking the PCM playback interface for PXA platforms using the sound/soc/ variant instead of the sound/arm variant. The commit below shows the inversion in the requestor lines. Fixes: d65a1458 ("ASoC: pxa: use snd_dmaengine_dai_dma_data") Signed-off-by:
-
John Flatness authored
commit e8ff581f upstream. The MacBookPro 12,1 has the same setup as the 11 for controlling the status of the optical audio light. Simply apply the existing workaround to the subsystem ID for the 12,1. [sorted the fixup entry by tiwai] Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105401Signed-off-by:
John Flatness <john@zerocrates.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 225db576 upstream. When OSS emulation is loaded on ISA SB AWE32 chip, we get now kernel warnings like: WARNING: CPU: 0 PID: 2791 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x51/0x80() sysfs: cannot create duplicate filename '/devices/isa/sbawe.0/sound/card0/seq-oss-0-0' It's because both emux synth and opl3 drivers try to register their OSS device object with the same static index number 0. This hasn't been a big problem until the recent rewrite of device management code (that exposes sysfs at the same time), but it's been an obvious bug. This patch works around it just by using a different index number of emux synth object. There can be a more elegant way to fix, but it's enough for now, as this code won't be touched so often, in anyway. Reported-and-tested-by:
Michael Shell <list1@michaelshell.org> Signed-off-by:
-
Mel Gorman authored
commit 2f84a899 upstream. SunDong reported the following on https://bugzilla.kernel.org/show_bug.cgi?id=103841 I think I find a linux bug, I have the test cases is constructed. I can stable recurring problems in fedora22(4.0.4) kernel version, arch for x86_64. I construct transparent huge page, when the parent and child process with MAP_SHARE, MAP_PRIVATE way to access the same huge page area, it has the opportunity to lead to huge page copy on write failure, and then it will munmap the child corresponding mmap area, but then the child mmap area with VM_MAYSHARE attributes, child process munmap this area can trigger VM_BUG_ON in set_vma_resv_flags functions (vma - > vm_flags & VM_MAYSHARE). There were a number of problems with the report (e.g. it's hugetlbfs that triggers this, not transparent huge pages) but it was fundamentally correct in that a VM_BUG_ON in set_vma_resv_flags() can be triggered that looks like this vma ffff8804651fd0d0 start 00007fc474e00000 end 00007fc475e00000 next ffff8804651fd018 prev ffff8804651fd188 mm ffff88046b1b1800 prot 8000000000000027 anon_vma (null) vm_ops ffffffff8182a7a0 pgoff 0 file ffff88106bdb9800 private_data (null) flags: 0x84400fb(read|write|shared|mayread|maywrite|mayexec|mayshare|dontexpand|hugetlb) ------------ kernel BUG at mm/hugetlb.c:462! SMP Modules linked in: xt_pkttype xt_LOG xt_limit [..] CPU: 38 PID: 26839 Comm: map Not tainted 4.0.4-default #1 Hardware name: Dell Inc. PowerEdge R810/0TT6JF, BIOS 2.7.4 04/26/2012 set_vma_resv_flags+0x2d/0x30 The VM_BUG_ON is correct because private and shared mappings have different reservation accounting but the warning clearly shows that the VMA is shared. When a private COW fails to allocate a new page then only the process that created the VMA gets the page -- all the children unmap the page. If the children access that data in the future then they get killed. The problem is that the same file is mapped shared and private. During the COW, the allocation fails, the VMAs are traversed to unmap the other private pages but a shared VMA is found and the bug is triggered. This patch identifies such VMAs and skips them. Signed-off-by:
Mel Gorman <mgorman@techsingularity.net> Reported-by:
SunDong <sund_sky@126.com> Reviewed-by:
Michal Hocko <mhocko@suse.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: David Rientjes <rientjes@google.com> Reviewed-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Tan, Jui Nee authored
commit 02bc933e upstream. On Intel Baytrail, there is case when interrupt handler get called, no SPI message is captured. The RX FIFO is indeed empty when RX timeout pending interrupt (SSSR_TINT) happens. Use the BIOS version where both HSUART and SPI are on the same IRQ. Both drivers are using IRQF_SHARED when calling the request_irq function. When running two separate and independent SPI and HSUART application that generate data traffic on both components, user will see messages like below on the console: pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler This commit will fix this by first checking Receiver Time-out Interrupt, if it is disabled, ignore the request and return without servicing. Signed-off-by:
Tan, Jui Nee <jui.nee.tan@intel.com> Acked-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
-
Guenter Roeck authored
commit a394d635 upstream. Actually, spi_master_put() after spi_alloc_master() must _not_ be followed by kfree(). The memory is already freed with the call to spi_master_put() through spi_master_class, which registers a release function. Calling both spi_master_put() and kfree() results in often nasty (and delayed) crashes elsewhere in the kernel, often in the networking stack. This reverts commit eb4af0f5. Link to patch and concerns: https://lkml.org/lkml/2012/9/3/269 or http://lkml.iu.edu/hypermail/linux/kernel/1209.0/00790.html Alexey Klimov: This revert becomes valid after 94c69f76 when spi-imx.c has been fixed and there is no need to call kfree() so comment for spi_alloc_master() should be fixed. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Alexey Klimov <alexey.klimov@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
commit 95913d97 upstream. So the problem this patch is trying to address is as follows: CPU0 CPU1 context_switch(A, B) ttwu(A) LOCK A->pi_lock A->on_cpu == 0 finish_task_switch(A) prev_state = A->state <-. WMB | A->on_cpu = 0; | UNLOCK rq0->lock | | context_switch(C, A) `-- A->state = TASK_DEAD prev_state == TASK_DEAD put_task_struct(A) context_switch(A, C) finish_task_switch(A) A->state == TASK_DEAD put_task_struct(A) The argument being that the WMB will allow the load of A->state on CPU0 to cross over and observe CPU1's store of A->state, which will then result in a double-drop and use-after-free. Now the comment states (and this was true once upon a long time ago) that we need to observe A->state while holding rq->lock because that will order us against the wakeup; however the wakeup will not in fact acquire (that) rq->lock; it takes A->pi_lock these days. We can obviously fix this by upgrading the WMB to an MB, but that is expensive, so we'd rather avoid that. The alternative this patch takes is: smp_store_release(&A->on_cpu, 0), which avoids the MB on some archs, but not important ones like ARM. Reported-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Vitaly Kuznetsov authored
commit 0b34a166 upstream. Currently there is a number of issues preventing PVHVM Xen guests from doing successful kexec/kdump: - Bound event channels. - Registered vcpu_info. - PIRQ/emuirq mappings. - shared_info frame after XENMAPSPACE_shared_info operation. - Active grant mappings. Basically, newly booted kernel stumbles upon already set up Xen interfaces and there is no way to reestablish them. In Xen-4.7 a new feature called 'soft reset' is coming. A guest performing kexec/kdump operation is supposed to call SCHEDOP_shutdown hypercall with SHUTDOWN_soft_reset reason before jumping to new kernel. Hypervisor (with some help from toolstack) will do full domain cleanup (but keeping its memory and vCPU contexts intact) returning the guest to the state it had when it was first booted and thus allowing it to start over. Doing SHUTDOWN_soft_reset on Xen hypervisors which don't support it is probably OK as by default all unknown shutdown reasons cause domain destroy with a message in toolstack log: 'Unknown shutdown reason code 5. Destroying domain.' which gives a clue to what the problem is and eliminates false expectations. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Stephen Smalley authored
commit ab76f7b4 upstream. Unused space between the end of __ex_table and the start of rodata can be left W+x in the kernel page tables. Extend the setting of the NX bit to cover this gap by starting from text_end rather than rodata_start. Before: ---[ High Kernel Mapping ]--- 0xffffffff80000000-0xffffffff81000000 16M pmd 0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd 0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte 0xffffffff81754000-0xffffffff81800000 688K RW GLB x pte 0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd 0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte 0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte 0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd 0xffffffff82200000-0xffffffffa0000000 478M pmd After: ---[ High Kernel Mapping ]--- 0xffffffff80000000-0xffffffff81000000 16M pmd 0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd 0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte 0xffffffff81754000-0xffffffff81800000 688K RW GLB NX pte 0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd 0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte 0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte 0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd 0xffffffff82200000-0xffffffffa0000000 478M pmd Signed-off-by:
Stephen Smalley <sds@tycho.nsa.gov> Acked-by:
Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Link: http://lkml.kernel.org/r/1443704662-3138-1-git-send-email-sds@tycho.nsa.govSigned-off-by:
-
Matt Fleming authored
commit a5caa209 upstream. Beginning with UEFI v2.5 EFI_PROPERTIES_TABLE was introduced that signals that the firmware PE/COFF loader supports splitting code and data sections of PE/COFF images into separate EFI memory map entries. This allows the kernel to map those regions with strict memory protections, e.g. EFI_MEMORY_RO for code, EFI_MEMORY_XP for data, etc. Unfortunately, an unwritten requirement of this new feature is that the regions need to be mapped with the same offsets relative to each other as observed in the EFI memory map. If this is not done crashes like this may occur, BUG: unable to handle kernel paging request at fffffffefe6086dd IP: [<fffffffefe6086dd>] 0xfffffffefe6086dd Call Trace: [<ffffffff8104c90e>] efi_call+0x7e/0x100 [<ffffffff81602091>] ? virt_efi_set_variable+0x61/0x90 [<ffffffff8104c583>] efi_delete_dummy_variable+0x63/0x70 [<ffffffff81f4e4aa>] efi_enter_virtual_mode+0x383/0x392 [<ffffffff81f37e1b>] start_kernel+0x38a/0x417 [<ffffffff81f37495>] x86_64_start_reservations+0x2a/0x2c [<ffffffff81f37582>] x86_64_start_kernel+0xeb/0xef Here 0xfffffffefe6086dd refers to an address the firmware expects to be mapped but which the OS never claimed was mapped. The issue is that included in these regions are relative addresses to other regions which were emitted by the firmware toolchain before the "splitting" of sections occurred at runtime. Needless to say, we don't satisfy this unwritten requirement on x86_64 and instead map the EFI memory map entries in reverse order. The above crash is almost certainly triggerable with any kernel newer than v3.13 because that's when we rewrote the EFI runtime region mapping code, in commit d2f7cbe7 ("x86/efi: Runtime services virtual mapping"). For kernel versions before v3.13 things may work by pure luck depending on the fragmentation of the kernel virtual address space at the time we map the EFI regions. Instead of mapping the EFI memory map entries in reverse order, where entry N has a higher virtual address than entry N+1, map them in the same order as they appear in the EFI memory map to preserve this relative offset between regions. This patch has been kept as small as possible with the intention that it should be applied aggressively to stable and distribution kernels. It is very much a bugfix rather than support for a new feature, since when EFI_PROPERTIES_TABLE is enabled we must map things as outlined above to even boot - we have no way of asking the firmware not to split the code/data regions. In fact, this patch doesn't even make use of the more strict memory protections available in UEFI v2.5. That will come later. Suggested-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Reported-by:
Matt Fleming <matt.fleming@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Chun-Yi <jlee@suse.com> Cc: Dave Young <dyoung@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: James Bottomley <JBottomley@Odin.com> Cc: Lee, Chun-Yi <jlee@suse.com> Cc: Leif Lindholm <leif.lindholm@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Link: http://lkml.kernel.org/r/1443218539-7610-2-git-send-email-matt@codeblueprint.co.ukSigned-off-by:
-
Dirk Müller authored
commit d2922422 upstream. The cpu feature flags are not ever going to change, so warning everytime can cause a lot of kernel log spam (in our case more than 10GB/hour). The warning seems to only occur when nested virtualization is enabled, so it's probably triggered by a KVM bug. This is a sensible and safe change anyway, and the KVM bug fix might not be suitable for stable releases anyway. Signed-off-by:
Dirk Mueller <dmueller@suse.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Andy Lutomirski authored
commit 83c133cf upstream. The NMI entry code that switches to the normal kernel stack needs to be very careful not to clobber any extra stack slots on the NMI stack. The code is fine under the assumption that SWAPGS is just a normal instruction, but that assumption isn't really true. Use SWAPGS_UNSAFE_STACK instead. This is part of a fix for some random crashes that Sasha saw. Fixes: 9b6e6a83 ("x86/nmi/64: Switch stacks on userspace NMI entry") Reported-and-tested-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Link: http://lkml.kernel.org/r/974bc40edffdb5c2950a5c4977f821a446b76178.1442791737.git.luto@kernel.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Andy Lutomirski authored
commit fc57a7c6 upstream. PARAVIRT_ADJUST_EXCEPTION_FRAME generates this code (using nmi as an example, trimmed for readability): ff 15 00 00 00 00 callq *0x0(%rip) # 2796 <nmi+0x6> 2792: R_X86_64_PC32 pv_irq_ops+0x2c That's a call through a function pointer to regular C function that does nothing on native boots, but that function isn't protected against kprobes, isn't marked notrace, and is certainly not guaranteed to preserve any registers if the compiler is feeling perverse. This is bad news for a CLBR_NONE operation. Of course, if everything works correctly, once paravirt ops are patched, it gets nopped out, but what if we hit this code before paravirt ops are patched in? This can potentially cause breakage that is very difficult to debug. A more subtle failure is possible here, too: if _paravirt_nop uses the stack at all (even just to push RBP), it will overwrite the "NMI executing" variable if it's called in the NMI prologue. The Xen case, perhaps surprisingly, is fine, because it's already written in asm. Fix all of the cases that default to paravirt_nop (including adjust_exception_frame) with a big hammer: replace paravirt_nop with an asm function that is just a ret instruction. The Xen case may have other problems, so document them. This is part of a fix for some random crashes that Sasha saw. Reported-and-tested-by:
-
David Woodhouse authored
commit 03da3ff1 upstream. In 2007, commit 07190a08 ("Mark TSC on GeodeLX reliable") bypassed verification of the TSC on Geode LX. However, this code (now in the check_system_tsc_reliable() function in arch/x86/kernel/tsc.c) was only present if CONFIG_MGEODE_LX was set. OpenWRT has recently started building its generic Geode target for Geode GX, not LX, to include support for additional platforms. This broke the timekeeping on LX-based devices, because the TSC wasn't marked as reliable: https://dev.openwrt.org/ticket/20531 By adding a runtime check on is_geode_lx(), we can also include the fix if CONFIG_MGEODEGX1 or CONFIG_X86_GENERIC are set, thus fixing the problem. Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Cc: Andres Salomon <dilinger@queued.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Marcelo Tosatti <marcelo@kvack.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1442409003.131189.87.camel@infradead.orgSigned-off-by:
-
Shaohua Li authored
commit 5d7c631d upstream. The APIC LVTT register is MMIO mapped but the TSC_DEADLINE register is an MSR. The write to the TSC_DEADLINE MSR is not serializing, so it's not guaranteed that the write to LVTT has reached the APIC before the TSC_DEADLINE MSR is written. In such a case the write to the MSR is ignored and as a consequence the local timer interrupt never fires. The SDM decribes this issue for xAPIC and x2APIC modes. The serialization methods recommended by the SDM differ. xAPIC: "1. Memory-mapped write to LVT Timer Register, setting bits 18:17 to 10b. 2. WRMSR to the IA32_TSC_DEADLINE MSR a value much larger than current time-stamp counter. 3. If RDMSR of the IA32_TSC_DEADLINE MSR returns zero, go to step 2. 4. WRMSR to the IA32_TSC_DEADLINE MSR the desired deadline." x2APIC: "To allow for efficient access to the APIC registers in x2APIC mode, the serializing semantics of WRMSR are relaxed when writing to the APIC registers. Thus, system software should not use 'WRMSR to APIC registers in x2APIC mode' as a serializing instruction. Read and write accesses to the APIC registers will occur in program order. A WRMSR to an APIC register may complete before all preceding stores are globally visible; software can prevent this by inserting a serializing instruction, an SFENCE, or an MFENCE before the WRMSR." The xAPIC method is to just wait for the memory mapped write to hit the LVTT by checking whether the MSR write has reached the hardware. There is no reason why a proper MFENCE after the memory mapped write would not do the same. Andi Kleen confirmed that MFENCE is sufficient for the xAPIC case as well. Issue MFENCE before writing to the TSC_DEADLINE MSR. This can be done unconditionally as all CPUs which have TSC_DEADLINE also have MFENCE support. [ tglx: Massaged the changelog ] Signed-off-by:
Shaohua Li <shli@fb.com> Reviewed-by:
-
Andy Shevchenko authored
commit 6bea0f6d upstream. In case we have less than maximum allowed channels (8) and autoconfiguration is enabled the DWC_PARAMS read is wrong because it uses different arithmetic to what is needed for channel priority setup. Re-do the caclulations properly. This now works on AVR32 board well. Fixes: fed2574b (dw_dmac: introduce software emulation of LLP transfers) Cc: yitian.bu@tangramtek.com Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Grazvydas Ignotas authored
commit 1dbdad75 upstream. The i2c5 pinctrl offsets are wrong. If the bootloader doesn't set the pins up, communication with tca6424a doesn't work (controller timeouts) and it is not possible to enable HDMI. Fixes: 9be495c4 ("ARM: dts: omap5-evm: Add I2c pinctrl data") Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Paul Bolle authored
commit fe2b5921 upstream. wf_unregister_client() increments the client count when a client unregisters. That is obviously incorrect. Decrement that client count instead. Fixes: 75722d39 ("[PATCH] ppc64: Thermal control for SMU based machines") Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Ard Biesheuvel authored
commit a077224f upstream. While working on the 32-bit ARM port of UEFI, I noticed a strange corruption in the kernel log. The following snprintf() statement (in drivers/firmware/efi/efi.c:efi_md_typeattr_format()) snprintf(pos, size, "|%3s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]", was producing the following output in the log: | | | | | |WB|WT|WC|UC] | | | | | |WB|WT|WC|UC] | | | | | |WB|WT|WC|UC] |RUN| | | | |WB|WT|WC|UC]* |RUN| | | | |WB|WT|WC|UC]* | | | | | |WB|WT|WC|UC] |RUN| | | | |WB|WT|WC|UC]* | | | | | |WB|WT|WC|UC] |RUN| | | | | | | |UC] |RUN| | | | | | | |UC] As it turns out, this is caused by incorrect code being emitted for the string() function in lib/vsprintf.c. The following code if (!(spec.flags & LEFT)) { while (len < spec.field_width--) { if (buf < end) *buf = ' '; ++buf; } } for (i = 0; i < len; ++i) { if (buf < end) *buf = *s; ++buf; ++s; } while (len < spec.field_width--) { if (buf < end) *buf = ' '; ++buf; } when called with len == 0, triggers an issue in the GCC SRA optimization pass (Scalar Replacement of Aggregates), which handles promotion of signed struct members incorrectly. This is a known but as yet unresolved issue. (https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932). In this particular case, it is causing the second while loop to be executed erroneously a single time, causing the additional space characters to be printed. So disable the optimization by passing -fno-ipa-sra. Acked-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Russell King authored
commit 9b55613f upstream. When a kernel is built covering ARMv6 to ARMv7, we omit to clear the IT state when entering a signal handler. This can cause the first few instructions to be conditionally executed depending on the parent context. In any case, the original test for >= ARMv7 is broken - ARMv6 can have Thumb-2 support as well, and an ARMv6T2 specific build would omit this code too. Relax the test back to ARMv6 or greater. This results in us always clearing the IT state bits in the PSR, even on CPUs where these bits are reserved. However, they're reserved for the IT state, so this should cause no harm. Fixes: d71e1352 ("Clear the IT state when invoking a Thumb-2 signal handler") Acked-by:
H. Nikolaus Schaller <hns@goldelico.com> Tested-by:
-
Guenter Roeck authored
commit 728d2940 upstream. The STEP_UP_TIME and STEP_DOWN_TIME registers are swapped for all chips but NCT6775. Reported-by:
Jean Delvare <jdelvare@suse.de> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
commit caa47047 upstream. The original patch introducing this header wrote the number of CPUs available and online in one order and then swapped those values when reading, fix it. Before: # perf record usleep 1 # perf report --header-only | grep 'nrcpus \(online\|avail\)' # nrcpus online : 4 # nrcpus avail : 4 # echo 0 > /sys/devices/system/cpu/cpu2/online # perf record usleep 1 # perf report --header-only | grep 'nrcpus \(online\|avail\)' # nrcpus online : 4 # nrcpus avail : 3 # echo 0 > /sys/devices/system/cpu/cpu1/online # perf record usleep 1 # perf report --header-only | grep 'nrcpus \(online\|avail\)' # nrcpus online : 4 # nrcpus avail : 2 After the fix, bringing back the CPUs online: # perf report --header-only | grep 'nrcpus \(online\|avail\)' # nrcpus online : 2 # nrcpus avail : 4 # echo 1 > /sys/devices/system/cpu/cpu2/online # perf record usleep 1 # perf report --header-only | grep 'nrcpus \(online\|avail\)' # nrcpus online : 3 # nrcpus avail : 4 # echo 1 > /sys/devices/system/cpu/cpu1/online # perf record usleep 1 # perf report --header-only | grep 'nrcpus \(online\|avail\)' # nrcpus online : 4 # nrcpus avail : 4 Acked-by:
Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Wang Nan <wangnan0@huawei.com> Fixes: fbe96f29 ("perf tools: Make perf.data more self-descriptive (v8)") Link: http://lkml.kernel.org/r/20150911153323.GP23511@kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
