- 13 Jan, 2015 4 commits
-
-
Sreekanth Reddy authored
Change List in this MPI2 specification, 1. Added SSUTimeout field to MPI2_CONFIG_PAGE_BIOS_1, and more defines for the BiosOptions field. Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Christoph Hellwig <hch@lst.de>
-
Sreekanth Reddy authored
Bump driver version to 19.100.00.00. Signed-off-by:
-
Sreekanth Reddy authored
mpt2sas, mpt3sas: Fail the host reset initiated due to discovery related I/O timeouts at driver load time When a flaky disk is there in a topology then during driver load, discovery related I/O times out; which results in SCSI error recovery initiating host reset and then the controller won't see any disk. In this patch, The driver would return FAILED status to the host reset initiated due to discovery related I/O timeout if ioc->is_driver_loading is set. This flag would be set until we exit out of scsih_scan_finished(). i.e. During device discovery if one of the disk is flaky (which responds to some discovery commands and doesn't respond to some) the driver wouldn't perform host reset for discovery related I/O timeout. Instead it would return Failure for the host reset resulting in the flaky disk getting removed by the SCSI Mid layer, so other disks would be added correctly. Signed-off-by:
-
Sreekanth Reddy authored
This patch will log a message when driver receives "Temperature Threshold exceeded" event from any temperature sensor. The message will look similar to like: mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!! mpt3sas0: Current Temp In Celsius: y where a b c d are threshold flags 0 1 2 3 Change_set: 1. Get the number of sensor count of this IOC by reading IO Unit page 8 at driver initialization time. 2. Also unmask the Temperature Threshold Event at driver initialization time 3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the firmware, then print the sensor number, the maximum threshold number it has exceed and the current temperature of this sensor. Signed-off-by:
-
- 12 Jan, 2015 1 commit
-
-
Sreekanth Reddy authored
Below is the changeset from the MPI specification and 2.00.34 header files: 1) Defined additional bits in the BiosOptions field of BIOS Page 1 to allow for finer control of X86 BIOS and UEFI BSD. 2) For the Clean Tool, reserved bit 26 of the Flags field for product specific use. Signed-off-by:
-
- 09 Jan, 2015 35 commits
-
-
Sumit.Saxena@avagotech.com authored
Update megaraid_sas driver version. Signed-off-by:
Sumit Saxena <sumit.saxena@avagotech.com> Reviewed-by:
-
Sumit.Saxena@avagotech.com authored
struct fusion_context *fusion is already memset to '0', so remove a redundant call to memmset "fusion->load_balance_info" to '0'. Signed-off-by:
Chaitra Basappa <chaitra.basappa@avagotech.com> Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
1) For fusion adapters, limit reserved frames for non SCSI commands to 8 (3 for parallel IOCTLs + 5 for driver's internal DCMDs). Earlier reserved commands for non SCSI IO frames was set to 32, so with this implementation, increased per controller "can_queue". Behavior of MFI controllers will remain unchanged. 2) Optimize the code related to per controller's 'can_queue' setting. Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
Driver calls megasas_complete_cmd() to call wake_up() for each MFI frame that was issued through the ioctl() interface prior to the kill adapter. This ensures userspace ioctl() system calls issued just before a kill adapter don't get stuck in wait state and IOCTLs are returned to the application. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
Update driver "mask_interrupts" before enable/disable hardware interrupt in order to avoid missing interrupts because of "mask_interrupts" still set to 1 and hardware interrupts are enabled. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
This patch will address the issue of SCSI device created at OS level for non existing VD. ldTgtIdtoLd[] array has size 256 for Extended VD firmware and 128 for legacy firmware. Accessing indices beyond array size (OS will send TUR, INQUIRY.. commands upto device index 255), may return valid LD value and that particular SCSI command will be SUCCESS and creating SCSI device for non existing target(VD). For legacy firmware (64 VD firmware), invalidates LD (by setting LD value to 0xff) in LdTgtIdtoLd[] array for device index beyond 127, so that invalid LD(0xff) value should be returned beyond device index beyond 127. Cc: <stable@vger.kernel.org> Signed-off-by:
Kashyap Desai <kashyap.desai@avagotech.com> Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
This patch adds support for Secure Encrypting Drives (SED) in JBOD mode: 1) If the firmware supports SED JBOD, all non read/write commands to JBODs will be sent via firmware path, and read/write commands to JBODs will be sent via fastpath. 2) If the firmware does not support SED JBOD, driver will fall back to the old design, i.e. send all JBOD I/O via fastpath. Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
This patch addresses below issues: 1) Few endianness bug fixes. 2) Break the iteration after (MAX_LOGICAL_DRIVES_EXT - 1)), instead of MAX_LOGICAL_DRIVES_EXT. 3) Optimization in MFI INIT frame before firing. 4) MFI IO frame should be 256bytes aligned. Code is optimized to reduce the size of frame for fusion adapters and make the MFI frame size calculation a bit transparent and readable. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hannes Reinecke authored
It is not good practice to display the kernel pointer in any message logs, and it doesn't display any additional information. And as we know have block-layer assigned tags we can use them to differentiate the messages. So remove any pointer references from the displayed messages. Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Hannes Reinecke authored
scsi_log_send() would display buffer pointer for higher logging levels. This is not only of questionable value but also exposes kernel pointer to userspace, which is discouraged in some setups. So drop this message altogether. Tested-by:
Robert Elliott <elliott@hp.com> Reviewed-by:
-
Hannes Reinecke authored
Instead of having constants.c littered with ifdef statements we should be moving dummy functions into the header and condintionally compile in constants.c if selected. And update the Kconfig description to reflect the actual size difference. Suggested-by:
Christoph Hellwig <hch@infradead.org> Tested-by:
-
Hannes Reinecke authored
Convert scsi_print_result() to use the per-cpu buffer for decoding the command result and disposition. Tested-by:
-
Hannes Reinecke authored
Convert sense buffer logging to use the per-cpu buffer to avoid line breakup. Tested-by:
-
Hannes Reinecke authored
libata already uses an internal buffer, so we should be using __scsi_format_command() here. Tested-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Hannes Reinecke authored
Use an external buffer for __scsi_print_command() and move command logging over to use the per-cpu logging buffer. With that we can guarantee the command always will always be formatted in one line. So we can even print out a variable length command correctly across several lines. Finally rename __scsi_print_command() to __scsi_format_comment() to better reflect the functionality. Tested-by:
-
Hannes Reinecke authored
The request tag provides a concise identification of a SCSI command, so we should be printing that out for scmd_printk(). Suggested-by:
-
Hannes Reinecke authored
Implement a per-cpu buffer for formatting messages to avoid line breaks up under high load. This patch implements scmd_printk() and sdev_prefix_printk() using the per-cpu buffer and makes sdev_printk() a wrapper for sdev_prefix_printk(). Tested-by:
-
K. Y. Srinivasan authored
On win8 and win8 r2 hosts force SPC-3 compliance for MSFT virtual disks. Ubuntu has been carrying a similar patch outside the tree for a while now. Starting with win10, the host will support SPC-3 compliance. Based on all the testing that has been done on win8 and win8 r2 hosts, we are comfortable claiming SPC-3 compliance on these hosts as well. This will enable TRIM support on these hosts. Suggested by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Long Li <longli@microsoft.com> Signed-off-by:
-
K. Y. Srinivasan authored
Commit 4cd83ecd changed the limits to reflect the values on the host. It turns out that WS2008R2 cannot correctly handle these new limits. Fix this bug by setting the limits based on the host. Signed-off-by:
-
K. Y. Srinivasan authored
The host asks the guest to scan when a LUN is removed or added. The only way a guest can identify the removed LUN is when an I/O is attempted on a removed LUN - the SRB status code indicates that the LUN is invalid. We currently handle this SRB status and remove the device. Rather than waiting for an I/O to remove the device, force the discovery of LUNs that may have been removed prior to discovering LUNs that may have been added. Signed-off-by:
-
K. Y. Srinivasan authored
The virtual HBA that storvsc implements can support multiple channels and targets. So, scan the host when the host notifies that a scan is needed. Signed-off-by:
-
Christoph Hellwig authored
STORVSC uses its own momory pool to manage device request data. However, the SCSI layer already has a mechanisim for allocating additional memory for each command issued to device driver. This patch removes the memory pool in STORVSC and makes it use SCSI layer to allocate memory for device request data. Reviewed-by:
-
James Smart authored
This patch, applicable to 8G/4G/2G adapters, adds a call that resumes transmit operations after a link bounce. Without it, targets that tried to suspend exchanges after a link bounce (such as tape devices using sequence level error recovery) would never resume io operation, causing scan failures, and eventually deadlocks if a device removal request is made. Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
Dick Kennedy <dick.kennedy@emulex.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Hannes Reinecke authored
'num_tags' is an unsigned char, so the check for 'ESP_MAX_TAGS' (which is set to 256) is pointless. Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Dan Carpenter authored
The "issue_reset" can be used uninitialized. It should be set to false at the start. Also I cleaned up the types a little by using bool. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Dan Carpenter authored
The "issue_reset" variable can be used uninitialized. It should be set to false at the start. Also I cleaned up the types by using bool. Signed-off-by:
-
Rickard Strandqvist authored
Replacing strncpy with strlcpy to avoid strings that lacks null terminate. And use the sizeof on the to string rather than strlen on the from string. Signed-off-by:
Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Acked-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
-
Ewan D. Milne authored
Accept the WRITE BUFFER command and do nothing other than set the appropriate "microcode has been changed" UA on the LU. >From an earlier patch by Doug Gilbert. Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Tested-by:
-
Ewan D. Milne authored
Generate a REPORTED LUNS DATA HAS CHANGED Unit Attention if sysfs "max_luns" is used to change the number of scsi_debug LUNs. This is only done if scsi_debug_scsi_level is SPC-3 or above. Additionally, implement SPC-4 behavior which only generates this Unit Attention on the first LUN on the target to receive a command after the change. This condition is cleared when a REPORT LUNS command is received. Signed-off-by:
-
Song Liu authored
Add power_status to SES device slot, so we can power on/off the HDDs behind the enclosure. Check firmware status in ses_set_* before sending control pages to firmware. Signed-off-by:
Song Liu <songliubraving@fb.com> Acked-by:
Dan Williams <dan.j.williams@intel.com> Reviewed-by:
Jens Axboe <axboe@fb.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Dan Williams authored
The name provided by firmware is in a vendor specific format, publish the slot number to have a reliable mechanism for identifying slots across firmware implementations. If the enclosure does not provide a slot number fallback to the component number which is guaranteed unique, and usually mirrors the slot number. Cleaned up the unused ses_component.desc in the process. Signed-off-by:
-
Dan Williams authored
Export the NAA logical id for the enclosure. This is optionally available from the sas_transport_class, but it is really a property of the enclosure. Signed-off-by:
-
Dan Williams authored
In support of a /dev/disk/by-slot populated with data from the enclosure and ses modules udev needs notification when the new interface files/links are available. Otherwise, any udev rules specified for the disk cannot assume that the enclosure topology has settled. Signed-off-by:
-
Dan Williams authored
The slot and address fields have a small window of instability when userspace can read them before initialization. Separate enclosure_component allocation from registration. Signed-off-by:
-
Rob Evers authored
Update scsi_report_lun_scan to initially always report up to 511 LUs, as the previous default max_report_luns did. Retry in a loop if not enough memory is available for the number of LUs reported. Parameter max_report_luns is removed as it is no longer used. Signed-off-by:
Rob Evers <revers@redhat.com> Reviewed-by:
-
