- 01 Nov, 2016 5 commits
-
-
David S. Miller authored
Iyappan Subramanian says: ==================== drivers: net: xgene: Fix coalescing bugs This patch set fixes the following, 1. Since ethernet v1 hardware has a bug related to coalescing, disabling this feature 2. Fixing ethernet v2 hardware, interrupt trigger region id to 2, to kickoff coalescing ==================== Signed-off-by:Iyappan Subramanian <isubramanian@apm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Iyappan Subramanian authored
Changing the interrupt trigger region id to 2 and the corresponding threshold set0/set1 values to 8/16. Signed-off-by:
Toan Le <toanle@apm.com> Signed-off-by:
-
Iyappan Subramanian authored
Since ethernet v1 hardware has a bug related to coalescing, disabling this feature. Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-4.9-20161031' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2016-10-31 this is a pull request of two patches for the upcoming v4.9 release. The first patch is by Lukas Resch for the sja1000 plx_pci driver that adds support for Moxa CAN devices. The second patch is by Oliver Hartkopp and fixes a potential kernel panic in the CAN broadcast manager. ==================== Signed-off-by:
-
Andy Gospodarek authored
Current bgmac code initializes some DMA settings in the receive control register for some hardware and then immediately clears those settings. Not clearing those settings results in ~420Mbps *improvement* in throughput; this system can now receive frames at line-rate on Broadcom 5871x hardware compared to ~520Mbps today. I also tested a few other values but found there to be no discernible difference in CPU utilization even if burst size and prefetching values are different. On the hardware tested there was no need to keep the code that cleared all but bits 16-17, but since there is a wide variety of hardware that used this driver (I did not look at all hardware docs for hardware using this IP block), I find it wise to move this call up and clear bits just after reading the default value from the hardware rather than completely removing it. This is a good candidate for -stable >=3.14 since that is when the code that was supposed to improve performance (but did not) was introduced. Signed-off-by:
Andy Gospodarek <gospo@broadcom.com> Fixes: 56ceecde ("bgmac: initialize the DMA controller of core...") Cc: Hauke Mehrtens <hauke@hauke-m.de> Acked-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
- 31 Oct, 2016 16 commits
-
-
David S. Miller authored
Xin Long says: ==================== sctp: a bunch of fixes by holding transport There are several places where it holds assoc after getting transport by searching from transport rhashtable, it may cause use-after-free issue. This patchset is to fix them by holding transport instead. v1->v2: Fix the changelog of patch 2/3 ==================== Signed-off-by: -
Xin Long authored
Prior to this patch, in rx path, before calling lock_sock, it needed to hold assoc when got it by __sctp_lookup_association, in case other place would free/put assoc. But in __sctp_lookup_association, it lookup and hold transport, then got assoc by transport->assoc, then hold assoc and put transport. It means it didn't hold transport, yet it was returned and later on directly assigned to chunk->transport. Without the protection of sock lock, the transport may be freed/put by other places, which would cause a use-after-free issue. This patch is to fix this issue by holding transport instead of assoc. As holding transport can make sure to access assoc is also safe, and actually it looks up assoc by searching transport rhashtable, to hold transport here makes more sense. Note that the function will be renamed later on on another patch. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Xin Long authored
Prior to this patch, it used a local variable to save the transport that is looked up by __sctp_lookup_association(), and didn't return it back. But in sctp_rcv, it is used to initialize chunk->transport. So when hitting this, even if it found the transport, it was still initializing chunk->transport with null instead. This patch is to return the transport back through transport pointer that is from __sctp_rcv_lookup_harder(). Signed-off-by:
-
Xin Long authored
In sctp_transport_lookup_process(), Commit 1cceda78 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock") moved cb() out of rcu lock, but it put transport and hold assoc instead, and ignore that cb() still uses transport. It may cause a use-after-free issue. This patch is to hold transport instead of assoc there. Fixes: 1cceda78 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock") Signed-off-by:
-
Dongli Zhang authored
While grant reference is of type uint32_t, xen-netfront erroneously casts it to signed short in BUG_ON(). This would lead to the xen domU panic during boot-up or migration when it is attached with lots of paravirtual devices. Signed-off-by:
Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by:
-
Oliver Hartkopp authored
Andrey Konovalov reported an issue with proc_register in bcm.c. As suggested by Cong Wang this patch adds a lock_sock() protection and a check for unsuccessful proc_create_data() in bcm_connect(). Reference: http://marc.info/?l=linux-netdev&m=147732648731237Reported-by:
Andrey Konovalov <andreyknvl@google.com> Suggested-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Lukas Resch authored
This patch adds support for Moxa CAN devices. Signed-off-by:
Lukas Resch <l.resch@incubedit.com> Signed-off-by:
Christoph Zehentner <c.zehentner@incubedit.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-for-davem-2016-10-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.9 iwlwifi * some fixes for suspend/resume with unified FW images * a fix for a false-positive lockdep report * a fix for multi-queue that caused an unnecessary 1 second latency * a fix for an ACPI parsing bug that caused a misleading error message brcmfmac * fix a variable uninitialised warning in brcmf_cfg80211_start_ap() ==================== Signed-off-by:
-
Ido Schimmel authored
In the device, a MID entry represents a group of local ports, which can later be bound to a MDB entry. The lookup of an existing MID entry is currently done using the provided MC MAC address and VID, from the Linux bridge. However, this can result in an incorrect reuse of the same MID index in different VLAN-unaware bridges (same IP MC group and VID 0). Fix this by performing the lookup based on FID instead of VID, which is unique across different bridges. Fixes: 3a49b4fd ("mlxsw: Adding layer 2 multicast support") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Acked-by:
Elad Raz <eladr@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Mintz, Yuval authored
When an interface is configured to use Tx/Rx-only queues, the length of the statistics would be shortened to accomodate only the statistics required per-each queue, and the values would be provided accordingly. However, the strings provided would still contain both Tx and Rx strings for each one of the queues [regardless of its configuration], which might lead to out-of-bound access when filling the buffers as well as incorrect statistics presented. Fixes: 9a4d7e86 ("qede: Add support for Tx/Rx-only queues.") Signed-off-by:
Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by:
-
Eric Dumazet authored
Sending zero checksum is ok for TCP, but not for UDP. UDPv6 receiver should by default drop a frame with a 0 checksum, and UDPv4 would not verify the checksum and might accept a corrupted packet. Simply replace such checksum by 0xffff, regardless of transport. This error was caught on SIT tunnels, but seems generic. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
-
Eric Dumazet authored
At accept() time, it is possible the parent has a non zero sk_err_soft, leftover from a prior error. Make sure we do not leave this value in the child, as it makes future getsockopt(SO_ERROR) calls quite unreliable. Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Florian Westphal authored
If a congestion control module doesn't provide .undo_cwnd function, tcp_undo_cwnd_reduction() will set cwnd to tp->snd_cwnd = max(tp->snd_cwnd, tp->snd_ssthresh << 1); ... which makes sense for reno (it sets ssthresh to half the current cwnd), but it makes no sense for dctcp, which sets ssthresh based on the current congestion estimate. This can cause severe growth of cwnd (eventually overflowing u32). Fix this by saving last cwnd on loss and restore cwnd based on that, similar to cubic and other algorithms. Fixes: e3118e83 ("net: tcp: add DCTCP congestion control algorithm") Cc: Lawrence Brakmo <brakmo@fb.com> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Glenn Judd <glenn.judd@morganstanley.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Xin Long authored
Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu. It leaded to that mtu lock doesn't really work when receiving the pkt of ICMPV6_PKT_TOOBIG. This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4 did in __ip_rt_update_pmtu. Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Jakub Sitnicki authored
Similar to commit c146066a ("ipv4: Don't use ufo handling on later transformed packets"), don't perform UFO on packets that will be IPsec transformed. To detect it we rely on the fact that headerlen in dst_entry is non-zero only for transformation bundles (xfrm_dst objects). Unwanted segmentation can be observed with a NETIF_F_UFO capable device, such as a dummy device: DEV=dum0 LEN=1493 ip li add $DEV type dummy ip addr add fc00::1/64 dev $DEV nodad ip link set $DEV up ip xfrm policy add dir out src fc00::1 dst fc00::2 \ tmpl src fc00::1 dst fc00::2 proto esp spi 1 ip xfrm state add src fc00::1 dst fc00::2 \ proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b tcpdump -n -nn -i $DEV -t & socat /dev/zero,readbytes=$LEN udp6:[fc00::2]:$LEN tcpdump output before: IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448 IP6 fc00::1 > fc00::2: frag (1448|48) IP6 fc00::1 > fc00::2: ESP(spi=0x00000001,seq=0x2), length 88 ... and after: IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448 IP6 fc00::1 > fc00::2: frag (1448|80) Fixes: e89e9cf5 ("[IPv4/IPv6]: UFO Scatter-gather approach") Signed-off-by:
Jakub Sitnicki <jkbs@redhat.com> Acked-by:
-
Mark Lord authored
The r8152 driver has been broken since (approx) 3.16.xx when support was added for hardware RX checksums on newer chip versions. Symptoms include random segfaults and silent data corruption over NFS. The hardware checksum logig does not work on the VER_02 dongles I have here when used with a slow embedded system CPU. Google reveals others reporting similar issues on Raspberry Pi. So, disable hardware RX checksum support for VER_02, and fix an obvious coding error for IPV6 checksums in the same function. Because this bug results in silent data corruption, it is a good candidate for back-porting to -stable >= 3.16.xx. Signed-off-by:
Mark Lord <mlord@pobox.com> Signed-off-by:
-
- 30 Oct, 2016 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "Lots of fixes, mostly drivers as is usually the case. 1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey Khoroshilov. 2) Fix element timeouts in netfilter's nft_dynset, from Anders K. Pedersen. 3) Don't put aead_req crypto struct on the stack in mac80211, from Ard Biesheuvel. 4) Several uninitialized variable warning fixes from Arnd Bergmann. 5) Fix memory leak in cxgb4, from Colin Ian King. 6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann. 7) Several VRF semantic fixes from David Ahern. 8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper. 9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet. 10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev. 11) Fix stale link state during failover in NCSCI driver, from Gavin Shan. 12) Fix netdev lower adjacency list traversal, from Ido Schimmel. 13) Propvide proper handle when emitting notifications of filter deletes, from Jamal Hadi Salim. 14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen. 15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac. 16) Several routing offload fixes in mlxsw driver, from Jiri Pirko. 17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy. 18) Validate chunk len before using it in SCTP, from Marcelo Ricardo Leitner. 19) Revert a netns locking change that causes regressions, from Paul Moore. 20) Add recursion limit to GRO handling, from Sabrina Dubroca. 21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon. 22) Avoid accessing stale vxlan/geneve socket in data path, from Pravin Shelar" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits) geneve: avoid using stale geneve socket. vxlan: avoid using stale vxlan socket. qede: Fix out-of-bound fastpath memory access net: phy: dp83848: add dp83822 PHY support enic: fix rq disable tipc: fix broadcast link synchronization problem ibmvnic: Fix missing brackets in init_sub_crq_irqs ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context" arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold net/mlx4_en: Save slave ethtool stats command net/mlx4_en: Fix potential deadlock in port statistics flow net/mlx4: Fix firmware command timeout during interrupt test net/mlx4_core: Do not access comm channel if it has not yet been initialized net/mlx4_en: Fix panic during reboot net/mlx4_en: Process all completions in RX rings after port goes up net/mlx4_en: Resolve dividing by zero in 32-bit system net/mlx4_core: Change the default value of enable_qos net/mlx4_core: Avoid setting ports to auto when only one port type is supported net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec ... -
pravin shelar authored
This patch is similar to earlier vxlan patch. Geneve device close operation frees geneve socket. This operation can race with geneve-xmit function which dereferences geneve socket. Following patch uses RCU mechanism to avoid this situation. Signed-off-by:
Pravin B Shelar <pshelar@ovn.org> Acked-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
pravin shelar authored
When vxlan device is closed vxlan socket is freed. This operation can race with vxlan-xmit function which dereferences vxlan socket. Following patch uses RCU mechanism to avoid this situation. Signed-off-by:
-
Mintz, Yuval authored
Driver allocates a shadow array for transmitted SKBs with X entries; That means valid indices are {0,...,X - 1}. [X == 8191] Problem is the driver also uses X as a mask for a producer/consumer in order to choose the right entry in the array which allows access to entry X which is out of bounds. To fix this, simply allocate X + 1 entries in the shadow array. Signed-off-by:
-
- 29 Oct, 2016 15 commits
-
-
Roger Quadros authored
This PHY has a compatible register set with DP83848x so add support for it. Acked-by:
Andrew F. Davis <afd@ti.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Govindarajulu Varadarajan authored
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000 bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes buffers. This causes memory corruption and sometimes crash. This is because of a race condition in adaptor between "RQ disable" clearing descriptor mini-cache and mini-cache valid bit being set by completion of descriptor fetch. This can result in stale RQ desc being cached and used when packets arrive. In this case, the stale descriptor have old MTU value. Solution is to write RQ->disable twice. The first write will stop any further desc fetches, allowing the second disable to clear the mini-cache valid bit without danger of a race. Also, the check for rq->running becoming 0 after writing rq->enable to 0 is not done properly. When incoming packets are flooding the interface, rq->running will pulse high for each dropped packet. Since the driver was waiting for 10us between each poll, it is possible to see rq->running = 1 1000 times in a row, even though it is not actually stuck running. This results in false failure of vnic_rq_disable(). Fix is to try more than 1000 time without delay between polls to ensure we do not miss when running goes low. In old adaptors rq->enable needs to be re-written to 0 when posted_index is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync. Signed-off-by:
Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by:
-
Jon Paul Maloy authored
In commit 2d18ac4b ("tipc: extend broadcast link initialization criteria") we tried to fix a problem with the initial synchronization of broadcast link acknowledge values. Unfortunately that solution is not sufficient to solve the issue. We have seen it happen that LINK_PROTOCOL/STATE packets with a valid non-zero unicast acknowledge number may bypass BCAST_PROTOCOL initialization, NAME_DISTRIBUTOR and other STATE packets with invalid broadcast acknowledge numbers, leading to premature opening of the broadcast link. When the bypassed packets finally arrive, they are inadvertently accepted, and the already correctly initialized acknowledge number in the broadcast receive link is overwritten by the invalid (zero) value of the said packets. After this the broadcast link goes stale. We now fix this by marking the packets where we know the acknowledge value is or may be invalid, and then ignoring the acks from those. To this purpose, we claim an unused bit in the header to indicate that the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR packets, plus those LINK_PROTOCOL packets sent out before the broadcast links are fully synchronized. This minor protocol update is fully backwards compatible. Reported-by:
John Thompson <thompa.atl@gmail.com> Tested-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Thomas Falcon authored
Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
-
Thomas Falcon authored
Schedule these XPORT event tasks in the shared workqueue so that IRQs are not freed in an interrupt context when sub-CRQs are released. Signed-off-by:
-
David S. Miller authored
This reverts commit 8d7533e5. It introduced kbuild failures, new version coming. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2016-10-27 This series contains fixes to ixgbe and i40e. Emil fixes a NULL pointer dereference when a macvlan interface is brought up while the PF is still down. David root caused the original panic that was fixed by commit id (a036244c "i40e: Fix kernel panic on enable/disable LLDP") and the fix was not quite correct, so removed the get_default_tc() and replaced it with a #define since there is only one TC supported as a default. Guilherme Piccoli fixes an issue where if we modprobe the driver module without enough MSI-X interrupts, then unload the module and reload it again, the kernel would crash. So if we fail to allocate enough MSI-X interrupts, we should disable them since they were previously enabled. Huaibin Wang found that the order of the arguments for ndo_dflt_bridge_getlink() were in the correct order, so fix the order. ==================== Signed-off-by:
-
Ivan Vecera authored
Commit 01cfbad7 "ipv4: Update parameters for csum_tcpudp_magic to their original types" changed parameters for csum_tcpudp_magic and csum_tcpudp_nofold for many platforms but not for PowerPC. Fixes: 01cfbad7 "ipv4: Update parameters for csum_tcpudp_magic to their original types" Cc: Alexander Duyck <aduyck@mirantis.com> Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Acked-by:
Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by:
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 bugfix from Thomas Gleixner: "A single bugfix for the recent changes related to registering the boot cpu when this has not happened before prefill_possible_map(). The main problem with this change got fixed already, but we missed the case where the local APIC is not yet mapped, when prefill_possible_map() is invoked, so the registration of the boot cpu which has the APIC bit set in CPUID will explode. I should have seen that issue earlier, but all I can do now is feeling embarassed" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/smpboot: Init apic mapping before usage
-
David S. Miller authored
Tariq Toukan says: ==================== mlx4 misc fixes for 4.9 This patchset contains several bug fixes from the team to the mlx4 Eth and Core drivers. Series generated against net commit: ecc515d7 'sctp: fix the panic caused by route update' ==================== Signed-off-by:
-
Tariq Toukan authored
Following the previous patch, as an optimization, the slave will not even bother sending the DUMP_ETH_STATS command over the comm channel. Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then called the FW command, with WRAPPED attribute. As a result, the fw command is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS. The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex* during processing. At the same time, a VF could be in the process of coming up, and could call mlx4_QUERY_FUNC_CAP. On the hypervisor, the command flow takes the *slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper. mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(), which takes the *counter mutex*. DEADLOCK. The fix is that the DUMP_ETH_STATS fw command should be called with the NATIVE attribute, so that on the hypervisor, this command does not enter the wrapper flow. Since the Hypervisor no longer goes through the wrapper code, we also simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds, but the returned data will be all zeroes). No need to test if it is the Hypervisor going through the wrapper. Fixes: f9baff50 ("mlx4_core: Add "native" argument to mlx4_cmd ...") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Eugenia Emantayev authored
Currently interrupt test that is part of ethtool selftest runs the check over all interrupt vectors of the device. In mlx4_en package part of interrupt vectors are uninitialized since mlx4_ib doesn't exist. This causes NOP FW command to time out. Change logic to test current port interrupt vectors only. Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
In the Hypervisor, there are several FW commands which are invoked before the comm channel is initialized (in mlx4_multi_func_init). These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others. If any of these commands fails, say with a timeout, the Hypervisor driver enters the internal error reset flow. In this flow, the driver attempts to notify all slaves via the comm channel that an internal error has occurred. Since the comm channel has not yet been initialized (i.e., mapped via ioremap), this will cause dereferencing a NULL pointer. To fix this, do not access the comm channel in the internal error flow if it has not yet been initialized. Fixes: 55ad3592 ("net/mlx4_core: Enable device recovery flow with SRIOV") Fixes: ab9c17a0 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet") Signed-off-by:
-
