Schedules a controller reset when it indicates it has a failed status. If
the device does not become ready after a reset, the pci device will be
scheduled for removal.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[fixed checkpatch issue]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

Adds controller error handling on resume power management. If the device
fails to initialize, the device is queued for a reset. If the reset fails,
a thread is spawned to remove the pci device.

If the device resumes as "busy", the device is responding to admin
commands but will not create IO queues. In this case, we need to remove
the gendisks and free the IO queues since they can't be used and may be
holding bios in their lists.

From testing, the dma pools require a pci device so this had to change
the pci driver 'remove' to release the dma resources in line with that
call instead of after all references to the device are released.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

Helps with line-length issues
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

During the initialisation path, the queue lock is taken without interrupt
protection.  It's perfectly safe to do so, because the interrupt handler
can't run at this point, but it confuses lockdep.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

For 32-bit versions of sg3-utils running on a 64-bit system. This is
mostly a copy from the relevent portions of fs/compat_ioctl.c, with
slight modifications for going through block_device_operations.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
[fixed up CONFIG_COMPAT=n build problems]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

Changes the type of dev->db_stride to unsigned and changes the value
stored there to be 1 << the current value. Then there is less
calculation to be done at completion time.
Signed-off-by: Haiyan Hu <huhaiyan@huawei.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

This reverts commit 69f0554e.

This patch breaks randconfig on at least the x86-64 architecture, and
most likely on others.  There is work underway to support uncompressed
kernels in a generic way, but it looks like it will amount to
rewriting the support from scratch; see the LKML thread in the Link:
for info.

Therefore, revert this change and wait for the fix.
Reported-by: Pavel Roskin <proski@gnu.org>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131113113418.167b8ffd@IRBT4585Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull CIFS fixes from Steve French:
 "A set of cifs fixes most important of which is Pavel's fix for some
  problems with handling Windows reparse points and also the security
  fix for setfacl over a cifs mount to Samba removing part of the ACL.
  Both of these fixes are for stable as well.

  Also added most of copychunk (copy offload) support to cifs although I
  expect a final patch in that series (to fix handling of larger files)
  in a few days (had to hold off on that in order to incorporate some
  additional code review feedback).

  Also added support for O_DIRECT on forcedirectio mounts (needed in
  order to run some of the server benchmarks over cifs and smb2/smb3
  mounts)"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] Warn if SMB3 encryption required by server
  setfacl removes part of ACL when setting POSIX ACLs to Samba
  [CIFS] Set copychunk defaults
  CIFS: SMB2/SMB3 Copy offload support (refcopy) phase 1
  cifs: Use data structures to compute NTLMv2 response offsets
  [CIFS] O_DIRECT opens should work on directio mounts
  cifs: don't spam the logs on unexpected lookup errors
  cifs: change ERRnomem error mapping from ENOMEM to EREMOTEIO
  CIFS: Fix symbolic links usage

Pull NFS client bugfixes:
 - Stable fix for data corruption when retransmitting O_DIRECT writes
 - Stable fix for a deep recursion/stack overflow bug in rpc_release_client
 - Stable fix for infinite looping when mounting a NFSv4.x volume
 - Fix a typo in the nfs mount option parser
 - Allow pNFS layouts to be compiled into the kernel when NFSv4.1 is

* tag 'nfs-for-3.13-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: fix pnfs Kconfig defaults
  NFS: correctly report misuse of "migration" mount option.
  nfs: don't retry detect_trunking with RPC_AUTH_UNIX more than once
  SUNRPC: Avoid deep recursion in rpc_release_client
  SUNRPC: Fix a data corruption issue when retransmitting RPC calls

Pull sound fixes from Takashi Iwai:
 "Two peaks in diffstat are for the audio EQ init of IDT codecs and the
  EMU2004 usb mixer addition, both of which are pretty device-specific,
  so safe to apply.  The rest are a bunch of small fixes, most of them
  are regression fixes"

* tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
  ALSA: hda - load EQ params into IDT codec on HP bNB13 systems
  ASoC: cs42l52: Correct MIC CTL mask
  ASoC: wm8962: Turn on regcache_cache_only before disabling regulator
  ALSA: jack: Unregister input device at disconnection
  ALSA: pcsp: Fix the order of input device unregistration
  ASoC: fsl: imx-pcm-fiq: omit fiq counter to avoid harm in unbalanced situations
  ASoC: blackfin: Fix missing break
  ALSA: usb-audio: add front jack channel selector for EMU0204
  ALSA: hda - Don't clear the power state at snd_hda_codec_reset()
  ASoC: arizona: Fix typo in name of EQ coefficient controls
  ALSA: hda - Control EAPD for Master volume on Lenovo N100
  ALSA: hda - Don't turn off EAPD for headphone on Lenovo N100
  ALSA: isa: not allocating enough space
  ALSA: snd-aoa: two copy and paste bugs
  ASoC: wm8997: Correct typo in ISRC mux routes
  ALSA: hda - Check keep_eapd_on before inv_eapd
  ALSA: hda - Fix Line Out automute on Realtek multifunction jacks
  ALSA: msnd: Avoid duplicated driver name
  ALSA: compress_core: don't return -EBADFD from poll if paused
  ALSA: hda - hdmi: Fix wrong baseline length in ATI/AMD generated ELD
  ...

Pull ARM SoC fixes from Olof Johansson:
 "A first set of batches of fixes for 3.13.  The diffstat is large
  mostly because we're adding a defconfig for a family that's been
  lacking it, and there's some missing clock information added for i.MX
  and OMAP.

  The at91 new code is around dealing with RTC/RTT reset at boot to fix
  possible hangs due to pending wakeup interrupts coming in during early
  boot"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
  ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
  ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
  doc: devicetree: Add bindings documentation for omap-des driver
  ARM: dts: doc: Document missing compatible property for omap-sham driver
  ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
  ARM: at91: fix hanged boot due to early rtt-interrupt
  ARM: at91: fix hanged boot due to early rtc-interrupt
  video: exynos_mipi_dsim: Remove unused variable
  ARM: highbank: only select errata 764369 if SMP
  ARM: sti: only select errata 764369 if SMP
  ARM: tegra: init fuse before setting reset handler
  ARM: vt8500: add defconfig for v6/v7 chips
  ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
  ARM: OMAP: devicetree: fix SPI node compatible property syntax items
  pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
  ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
  MAINTAINERS: drop discontinued mailing list
  ARM: dts: i.MX51: Fix OTG PHY clock
  ARM: imx: set up pllv3 POWER and BYPASS sequentially
  ARM: imx: pllv3 needs relock in .set_rate() call
  ...

Pull perf fixes from Ingo Molnar:
 "Tooling changes only: it includes the ARM tooling fixlets, various
  other fixes, smaller updates, minor cleanups"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf record: Add an option to force per-cpu mmaps
  perf probe: Add '--demangle'/'--no-demangle'
  perf ui browser: Fix segfault caused by off by one handling END key
  perf symbols: Limit max callchain using max_stack on DWARF unwinding too
  perf evsel: Introduce perf_evsel__prev() method
  perf tools: Use perf_evlist__{first,last}, perf_evsel__next
  perf tools: Synthesize anon MMAP records again
  perf top: Add missing newline if the 'uid' is invalid
  perf tools: Remove trivial extra semincolon
  perf trace: Tweak summary output
  tools/perf/build: Fix feature-libunwind-debug-frame handling
  tools/perf/build: Fix timerfd feature check

Pull tracing update from Steven Rostedt:
 "This batch of changes is mostly clean ups and small bug fixes.  The
  only real feature that was added this release is from Namhyung Kim,
  who introduced "set_graph_notrace" filter that lets you run the
  function graph tracer and not trace particular functions and their
  call chain.

  Tom Zanussi added some updates to the ftrace multibuffer tracing that
  made it more consistent with the top level tracing.

  One of the fixes for perf function tracing required an API change in
  RCU; the addition of "rcu_is_watching()".  As Paul McKenney is pushing
  that change in this release too, he gave me a branch that included all
  the changes to get that working, and I pulled that into my tree in
  order to complete the perf function tracing fix"

* tag 'trace-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Add rcu annotation for syscall trace descriptors
  tracing: Do not use signed enums with unsigned long long in fgragh output
  tracing: Remove unused function ftrace_off_permanent()
  tracing: Do not assign filp->private_data to freed memory
  tracing: Add helper function tracing_is_disabled()
  tracing: Open tracer when ftrace_dump_on_oops is used
  tracing: Add support for SOFT_DISABLE to syscall events
  tracing: Make register/unregister_ftrace_command __init
  tracing: Update event filters for multibuffer
  recordmcount.pl: Add support for __fentry__
  ftrace: Have control op function callback only trace when RCU is watching
  rcu: Do not trace rcu_is_watching() functions
  ftrace/x86: skip over the breakpoint for ftrace caller
  trace/trace_stat: use rbtree postorder iteration helper instead of opencoding
  ftrace: Add set_graph_notrace filter
  ftrace: Narrow down the protected area of graph_lock
  ftrace: Introduce struct ftrace_graph_data
  ftrace: Get rid of ftrace_graph_filter_enabled
  tracing: Fix potential out-of-bounds in trace_get_user()
  tracing: Show more exact help information about snapshot

Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm changes from Thierry Reding:
 "Mostly bug fixes and clean up.  There is a new driver, which is
  actually moving a custom PWM driver from drivers/misc.

  The majority of the patches are enhancements to the device tree
  support in the pwm-backlight driver.  Backlights can now additionally
  be powered using a regulator and enabled using a GPIO in addition to
  just the PWM input"

* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
  Documentation/pwm: Update supported SoC name for pwm-samsung
  pwm: samsung: Fix kernel warning while unexporting a channel
  MAINTAINERS: Move PWM subsystem tree to kernel.org
  Documentation/pwm: Fix trivial typos
  pwm-backlight: Remove unused variable
  pwm_backlight: avoid short blank screen while doing hibernation
  pwm-backlight: Fix brightness adjustment
  pwm: add ep93xx PWM support
  pwm-backlight: Allow for non-increasing brightness levels
  pwm-backlight: Add power supply support
  pwm-backlight: Use new enable_gpio field
  unicore32: Initialize PWM backlight enable_gpio field
  ARM: shmobile: Initialize PWM backlight enable_gpio field
  ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
  ARM: pxa: Initialize PWM backlight enable_gpio field
  ARM: OMAP: Initialize PWM backlight enable_gpio field
  pwm-backlight: Add optional enable GPIO
  pwm-backlight: Track enable state
  pwm-backlight: Refactor backlight power on/off
  pwm-backlight: Improve readability
  ...

Pull nfsd changes from Bruce Fields:
 "This includes miscellaneous bugfixes and cleanup and a performance fix
  for write-heavy NFSv4 workloads.

  (The most significant nfsd-relevant change this time is actually in
  the delegation patches that went through Viro, fixing a long-standing
  bug that can cause NFSv4 clients to miss updates made by non-nfs users
  of the filesystem.  Those enable some followup nfsd patches which I
  have queued locally, but those can wait till 3.14)"

* 'nfsd-next' of git://linux-nfs.org/~bfields/linux: (24 commits)
  nfsd: export proper maximum file size to the client
  nfsd4: improve write performance with better sendspace reservations
  svcrpc: remove an unnecessary assignment
  sunrpc: comment typo fix
  Revert "nfsd: remove_stid can be incorporated into nfs4_put_delegation"
  nfsd4: fix discarded security labels on setattr
  NFSD: Add support for NFS v4.2 operation checking
  nfsd4: nfsd_shutdown_net needs state lock
  NFSD: Combine decode operations for v4 and v4.1
  nfsd: -EINVAL on invalid anonuid/gid instead of silent failure
  nfsd: return better errors to exportfs
  nfsd: fh_update should error out in unexpected cases
  nfsd4: need to destroy revoked delegations in destroy_client
  nfsd: no need to unhash_stid before free
  nfsd: remove_stid can be incorporated into nfs4_put_delegation
  nfsd: nfs4_open_delegation needs to remove_stid rather than unhash_stid
  nfsd: nfs4_free_stid
  nfsd: fix Kconfig syntax
  sunrpc: trim off EC bytes in GSSAPI v2 unwrap
  gss_krb5: document that we ignore sequence number
  ...

Pull btrfs fixes from Chris Mason:
 "This pull fixes the empty_zero_page bug that Heiko reported, and
  includes one more cleanup from Al Viro"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: get rid of fdentry()
  btrfs: fix empty_zero_page misusage

Pull /dev/random changes from Ted Ts'o:
 "The /dev/random changes for 3.13 including a number of improvements in
  the following areas: performance, avoiding waste of entropy, better
  tracking of entropy estimates, support for non-x86 platforms that have
  a register which can't be used for fine-grained timekeeping, but which
  might be good enough for the random driver.

  Also add some printk's so that we can see how quickly /dev/urandom can
  get initialized, and when programs try to use /dev/urandom before it
  is fully initialized (since this could be a security issue).  This
  shouldn't be an issue on x86 desktop/laptops --- a test on my Lenovo
  T430s laptop shows that /dev/urandom is getting fully initialized
  approximately two seconds before the root file system is mounted
  read/write --- this may be an issue with ARM and MIPS embedded/mobile
  systems, though.  These printk's will be a useful canary before
  potentially adding a future change to start blocking processes which
  try to read from /dev/urandom before it is initialized, which is
  something FreeBSD does already for security reasons, and which
  security folks have been agitating for Linux to also adopt"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: add debugging code to detect early use of get_random_bytes()
  random: initialize the last_time field in struct timer_rand_state
  random: don't zap entropy count in rand_initialize()
  random: printk notifications for urandom pool initialization
  random: make add_timer_randomness() fill the nonblocking pool first
  random: convert DEBUG_ENT to tracepoints
  random: push extra entropy to the output pools
  random: drop trickle mode
  random: adjust the generator polynomials in the mixing function slightly
  random: speed up the fast_mix function by a factor of four
  random: cap the rate which the /dev/urandom pool gets reseeded
  random: optimize the entropy_store structure
  random: optimize spinlock use in add_device_randomness()
  random: fix the tracepoint for get_random_bytes(_arch)
  random: account for entropy loss due to overwrites
  random: allow fractional bits to be tracked
  random: statically compute poolbitshift, poolbytes, poolbits
  random: mix in architectural randomness earlier in extract_buf()

Merge tag 'asoc-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.13

A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.

We do not support SMB3 encryption yet, warn if server responds
that SMB3 encryption is mandatory.
Signed-off-by: Steve French <smfrench@gmail.com>

Commit 7d02c4d6 ("iommu/shmobile: Enable the driver on all ARM
platforms") completely brokenly enabled the shmobile-iommu driver under
COMPILE_TEST.

It's bogus, because it won't compile anywhere else than ARM, since it
tries to include <asm/dma-iommu.h>, which is very much ARM-only.

So remove the bogus COMPILE_TEST dependency, which just causes
allmodconfig to fail on non-ARM platforms.

Cc: Joerg Roedel <joro@8bytes.org>
Cc: iommu@lists.linux-foundation.org
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

setfacl over cifs mounts can remove the default ACL when setting the
(non-default part of) the ACL and vice versa (we were leaving at 0
rather than setting to -1 the count field for the unaffected
half of the ACL.  For example notice the setfacl removed
the default ACL in this sequence:

steven@steven-GA-970A-DS3:~/cifs-2.6$ getfacl /mnt/test-dir ; setfacl
-m default:user:test:rwx,user:test:rwx /mnt/test-dir
getfacl: Removing leading '/' from absolute path names
user::rwx
group::r-x
other::r-x
default:user::rwx
default:user:test:rwx
default:group::r-x
default:mask::rwx
default:other::r-x

steven@steven-GA-970A-DS3:~/cifs-2.6$ getfacl /mnt/test-dir
getfacl: Removing leading '/' from absolute path names
user::rwx
user:test:rwx
group::r-x
mask::rwx
other::r-x

CC: Stable <stable@kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Jeremy Allison <jra@samba.org>

Pull HID updates from Jiri Kosina:
 - i2c-hid is not querying init reports any more, as it's not mandated
   by the spec, and annoys quite a few devices during enumeration, by
   Bibek Basu
 - a lot of fixes for Logitech devices, by Simon Wood
 - hid-apple now has an option to switch between Option and Command
   mode, by Nanno Langstraat
 - Some more workarounds for severely broken ELO devices, by Oliver
   Neukum
 - more devm conversions, by Benjamin Tissoires
 - wiimote correctness fixes, by David Herrmann
 - a lot of added support for various new device IDs and random small
   fixes here and there"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
  HID: enable Mayflash USB Gamecube Adapter
  HID: sony: Add force feedback support for Dualshock3 USB
  Input: usbtouchscreen: ignore eGalax/D-Wav/EETI HIDs
  HID: don't ignore eGalax/D-Wav/EETI HIDs
  HID: roccat: add missing special driver declarations
  HID:hid-lg4ff: Correct Auto-center strength for wheels other than MOMO and MOMO2
  HID:hid-lg4ff: Initialize device properties before we touch autocentering.
  HID:hid-lg4ff: ensure ConstantForce is disabled when set to 0
  HID:hid-lg4ff: Switch autocentering off when strength is set to zero.
  HID:hid-lg4ff: Scale autocentering force properly on Logitech wheel
  HID: roccat: fix Coverity CID 141438
  HID: multitouch: add manufacturer to Kconfig help text
  HID: logitech-dj: small cleanup in rdcat()
  HID: remove self-assignment from hid_input_report
  HID: hid-sensor-hub: fix report size
  HID: i2c-hid: Stop querying for init reports
  HID: roccat: add support for Ryos MK keyboards
  HID: roccat: generalize some common code
  HID: roccat: add new device return value
  HID: wiimote: add pro-controller analog stick calibration
  ...

Pull trivial tree updates from Jiri Kosina:
 "Usual earth-shaking, news-breaking, rocket science pile from
  trivial.git"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
  doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
  doc: add missing files to timers/00-INDEX
  timekeeping: Fix some trivial typos in comments
  mm: Fix some trivial typos in comments
  irq: Fix some trivial typos in comments
  NUMA: fix typos in Kconfig help text
  mm: update 00-INDEX
  doc: Documentation/DMA-attributes.txt fix typo
  DRM: comment: `halve' -> `half'
  Docs: Kconfig: `devlopers' -> `developers'
  doc: typo on word accounting in kprobes.c in mutliple architectures
  treewide: fix "usefull" typo
  treewide: fix "distingush" typo
  mm/Kconfig: Grammar s/an/a/
  kexec: Typo s/the/then/
  Documentation/kvm: Update cpuid documentation for steal time and pv eoi
  treewide: Fix common typo in "identify"
  __page_to_pfn: Fix typo in comment
  Correct some typos for word frequency
  clk: fixed-factor: Fix a trivial typo
  ...

Pull input updates from Dmitry Torokhov:
 "Updates for the input subsystem.  You will get an new drivers for
  Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
  bunch of driver fixes and cleanups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
  Revert "Input: ALPS - add support for model found on Dell XT2"
  arm: dts: am335x sk: add touchscreen support
  Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
  Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
  Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
  Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
  Input: tnetv107x-keypad - make irqs signed for error handling
  Input: add driver for Neonode zForce based touchscreens
  Input: sh_keysc - enable the driver on all ARM platforms
  Input: remove a redundant max() call
  Input: mousedev - allow disabling even without CONFIG_EXPERT
  Input: allow deselecting serio drivers even without CONFIG_EXPERT
  Input: i8042 - add PNP modaliases
  Input: evdev - fall back to vmalloc for client event buffer
  Input: cypress_ps2 - do not consider data bad if palm is detected
  Input: cypress_ps2 - remove useless cast
  Input: fix PWM-related undefined reference errors
  Input: ALPS - change secondary device's name
  Input: wacom - not all multi-interface devices support touch
  Input: nspire-keypad - add missing clk_disable_unprepare() on error path
  ...

Pull MFD updates from Samuel Ortiz:
 "For the 3.13 merge window we have a couple of new drivers for the AMS
  AS3722 PMIC and for STMicroelectronics STw481x PMIC.

  Although this is a smaller update than usual, we also have:

   - Device tree support for the max77693 driver

   - linux/of.h inclusion for all DT compatible MFD drivers, to avoid
     build breakage in the future

   - Support for Intel Wildcat Point-LP PCH through the lpc_ich driver

   - A small arizona update for new wm5110 DSP registers and a few fixes

   - A small palmas update as well, including an of_device table
     addition and a few minor fixes

   - Two small mfd-core changes, one including a memory leak fix for
     when mfd_add_device() fails

   - Our usual round of minor cleanups and janitorial fixes"

* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
  Documentation: mfd: Update s2mps11.txt
  mfd: pm8921: Potential NULL dereference in pm8921_remove()
  mfd: Fix memory leak in mfd_add_devices()
  mfd: Stop setting refcounting pointers in original mfd_cell arrays
  mfd: wm5110: Enable micd clamp functionality
  mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
  mfd: max77693: Fix up bug of wrong interrupt number
  mfd: as3722: Don't export the regmap config
  mfd: twl6040: Remove obsolete cleanup for i2c clientdata
  mfd: tps65910: Remove warning during dt node parsing
  mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
  mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
  mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
  mfd: Add support for ams AS3722 PMIC
  mfd: max77693: Include linux/of.h header
  mfd: tc3589x: Detect the precise version
  mfd: omap-usb: prepare/unprepare clock while enable/disable
  mfd: max77686: Include linux/of.h header
  mfd: max8907: Include linux/of.h header
  mfd: max8997: Include linux/of.h header
  ...

Pull hwmon fixes and updates from Jean Delvare:
 "All lm90 driver fixes and improvements"

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  Documentation: dt: hwmon: Add OF document for LM90
  hwmon: (lm90) Add power control
  hwmon: (lm90) Add support for TI TMP451
  hwmon: (lm90) Use enums for the indexes of temp8 and temp11
  hwmon: (lm90) Add support to handle IRQ
  hwmon: (lm90) Define status bits
  hwmon: (lm90) Fix max6696 alarm handling

Pull second round of block driver updates from Jens Axboe:
 "As mentioned in the original pull request, the bcache bits were pulled
  because of their dependency on the immutable bio vecs.  Kent re-did
  this part and resubmitted it, so here's the 2nd round of (mostly)
  driver updates for 3.13.  It contains:

 - The bcache work from Kent.

 - Conversion of virtio-blk to blk-mq.  This removes the bio and request
   path, and substitutes with the blk-mq path instead.  The end result
   almost 200 deleted lines.  Patch is acked by Asias and Christoph, who
   both did a bunch of testing.

 - A removal of bootmem.h include from Grygorii Strashko, part of a
   larger series of his killing the dependency on that header file.

 - Removal of __cpuinit from blk-mq from Paul Gortmaker"

* 'for-linus' of git://git.kernel.dk/linux-block: (56 commits)
  virtio_blk: blk-mq support
  blk-mq: remove newly added instances of __cpuinit
  bcache: defensively handle format strings
  bcache: Bypass torture test
  bcache: Delete some slower inline asm
  bcache: Use ida for bcache block dev minor
  bcache: Fix sysfs splat on shutdown with flash only devs
  bcache: Better full stripe scanning
  bcache: Have btree_split() insert into parent directly
  bcache: Move spinlock into struct time_stats
  bcache: Kill sequential_merge option
  bcache: Kill bch_next_recurse_key()
  bcache: Avoid deadlocking in garbage collection
  bcache: Incremental gc
  bcache: Add make_btree_freeing_key()
  bcache: Add btree_node_write_sync()
  bcache: PRECEDING_KEY()
  bcache: bch_(btree|extent)_ptr_invalid()
  bcache: Don't bother with bucket refcount for btree node allocations
  bcache: Debug code improvements
  ...

Merge tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Few clock fixes, a runtime PM fix, and pinctrl-single fix along
with few other fixes that popped up during the merge window.

* tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
  ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
  doc: devicetree: Add bindings documentation for omap-des driver
  ARM: dts: doc: Document missing compatible property for omap-sham driver
  ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
  ARM: OMAP: devicetree: fix SPI node compatible property syntax items
  pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
  ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
  + sync with newer trunk

Merge branches 'for-3.12/upstream-fixes', 'for-3.13/holtek', 'for-3.13/i2c-hid', 'for-3.13/logitech', 'for-3.13/multitouch', 'for-3.13/roccat', 'for-3.13/upstream' and 'for-3.13/wiimote' into for-linus

Pull drm regression fix from Dave Airlie:
 "Forgot this one liner was necessary to fix module reload issues
  introduced earlier in the drm pull"

* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
  drm: check for !kdev in drm_unplug_minor()

Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin updates from Steven Miao:
 "Blackfin gpio changes, add adi pinctrl driver, and bug fixes"

* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: fix build warning for unused variable
  smp: bf561: and smb_wmb()/smp_rmb() at ipi send/receive
  pm: use GFP_ATOMIC when pm core call this function
  blackfin: serial: Add serial port_fer and port_mux early platform resources.
  blackfin: pinctrl-adi2: code cleanup after using pinctrl-adi2
  blackfin: adi gpio driver and pinctrl driver support
  bf609: update default config for spi
  Blackfin: bfin_gpio: Use proper mask for comparing pfunc

Pull OpenRISC updates from Jonas Bonn:
 - small cleanups to make allmodconfig pass
 - defconfig refresh
 - a handful of code sanitization patches

* tag 'for-3.13' of git://git.openrisc.net/~jonas/linux:
  openrisc: Refactor or32_early_setup()
  openrisc: Remove unused declaration of __initramfs_start
  openrisc: Use the declarations provided by <asm/sections.h>
  openrisc: Refresh or1ksim_defconfig for v3.12
  openrisc: Refactor 16-bit constant relocation
  openrisc: include: asm: Kbuild: add default "vga.h"
  openrisc: Makefile: append "-D__linux__" to KBUILD_CFLAGS

Pull misc kbuild changes from Michal Marek:
 - make tags fixes again
 - scripts/show_delta fix for newer python
 - scripts/kernel-doc does not fail on unknown function prototype
 - one less coccinelle check this time

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/tags.sh: remove obsolete __devinit[const|data]
  scripts/kernel-doc: make unknown function prototype a Warning instead of an Error
  show_delta: Update script to support python versions 2.5 through 3.3
  scripts/coccinelle/api: remove devm_request_and_ioremap.cocci
  scripts/tags.sh: Increase identifier list

Pull kconfig changes from Michal Marek:
 - xconfig stores its setting in a meaningful path
   (~/.config/kernel.org/qconf.conf)
 - kconfig symbol search fix
 - documentation fixes
 - cleanup & comment update
 - fix warning when a kconfig symbol is defined with two different types
 - Yann is now officially listed as maintainer of kconfig, but he
   prefers me to send pull requests for now

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  MAINTAINERS: New kconfig maintainer
  xconfig: Fix the filename for GUI settings
  kconfig: fix bug in search results string: use strlen(gstr->s), not gstr->len
  kconfig: remove unused definition from scanner
  kconfig: adjust warning message for conflicting types
  kconfig: fix trivial typos and update mconf documentation
  kconfig: add short explanation to SYMBOL_WRITE
  Documentation/kbuild/kconfig.txt: 'make listnewconfig' replaces: yes "" | make oldconfig

Pull kbuild changes from Michal Marek:
 - LTO fixes, but the kallsyms part had to be reverted
 - Pass -Werror=implicit-int and -Werror=strict-prototypes to the
   compiler by default
 - snprintf fix in modpost
 - remove GREP_OPTIONS from the environment to be immune against exotic
   grep option settings

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kallsyms: Revert back to 128 max symbol length
  Kbuild: Ignore GREP_OPTIONS env variable
  scripts: kallsyms: Use %zu to print 'size_t'
  scripts/bloat-o-meter: use .startswith rather than fragile slicing
  scripts/bloat-o-meter: ignore changes in the size of linux_banner
  kbuild: replace unbounded sprintf call in modpost
  kbuild, bloat-o-meter: fix static detection
  Kbuild: Handle longer symbols in kallsyms.c
  kbuild: Increase kallsyms max symbol length
  Makefile: enable -Werror=implicit-int and -Werror=strict-prototypes by default

Pull Kconfig cleanups from Mark Salter:
 "Remove some unused config options from C6X and clean up PC_PARPORT
  dependencies.  The latter was discussed here:

    https://lkml.org/lkml/2013/10/8/12"

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  c6x: remove unused COMMON_CLKDEV Kconfig parameter
  Kconfig cleanup (PARPORT_PC dependencies)
  x86: select ARCH_MIGHT_HAVE_PC_PARPORT
  unicore32: select ARCH_MIGHT_HAVE_PC_PARPORT
  sparc: select ARCH_MIGHT_HAVE_PC_PARPORT
  sh: select ARCH_MIGHT_HAVE_PC_PARPORT
  powerpc: select ARCH_MIGHT_HAVE_PC_PARPORT
  parisc: select ARCH_MIGHT_HAVE_PC_PARPORT
  mips: select ARCH_MIGHT_HAVE_PC_PARPORT
  microblaze: select ARCH_MIGHT_HAVE_PC_PARPORT
  m68k: select ARCH_MIGHT_HAVE_PC_PARPORT
  ia64: select ARCH_MIGHT_HAVE_PC_PARPORT
  arm: select ARCH_MIGHT_HAVE_PC_PARPORT
  alpha: select ARCH_MIGHT_HAVE_PC_PARPORT
  c6x: remove unused parameter in Kconfig

Patch 2 of the copy chunk series (the final patch will
use these to handle copies of files larger than the chunk size.

We set the same defaults that Windows and Samba expect for
CopyChunk.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: David Disseldorp <ddiss@samba.org>

From Nicolas Ferre, fixes for early boot hangs on at91:

Fixes for RTT & RTC interrupts that can fire early during boot process
and kill the system.

* tag 'at91-fixes-non-critical' of git://github.com/at91linux/linux-at91:
  ARM: at91: fix hanged boot due to early rtt-interrupt
  ARM: at91: fix hanged boot due to early rtc-interrupt

Defaulting to m seem to prevent building the pnfs layout modules into the
kernel.  Default to the value of CONFIG_NFS_V4 make sure they are
built in for built-in NFSv4 support and modular for a modular NFSv4.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>