[ Upstream commit c8da1d15 ]

DesignWare I2C controller was observed running at 105.93kHz rather
than the specified 100kHz.  Adjust device tree settings to bring it
within spec (a slightly conservative 98 MHz).
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b943f17e ]

In lio_enable_irq, the pkt_in_done count register was being cleared to
zero.  However, there could be some completed instructions which were not
yet processed due to budget and limit constraints.
So, only write this register with the number of actual completions
that were processed.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 64858773 ]

This patch adds missing properties to the CODEC and sound nodes, so the
audio will work also on Snow rev5 Chromebook. This patch is an extension
to the commit e9eefc3f ("ARM: dts: exynos: Add missing clock and
DAI properties to the max98095 node in Snow Chromebook")
and commit 6ab56993 ("ARM: dts: exynos: Enable HDMI audio on Snow
Chromebook").  It has been reported that such changes work fine on the
rev5 board too.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Fixed typo in phandle to &max98090]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 21cb5a27 ]

HDMI-HPD was set active low, moreover by default pincontrol chip sets
pull-down on the pin. As a result HDMI driver assumes TV is always
connected regardless of actual state.  The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 620375c8 ]

HDMI-DDC for unknown reasons doesn't work with Exynos I2C controllers.
Fortunately i2c-gpio comes to the rescue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit feef7918 ]

Setting GPIO 21 high seems to be required to enable power to USB ports
on the WNDR3400v3. As there is already similar code for WNR3500L,
make the existing USB power GPIO code generic and use that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20259/
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 556a36a7 ]

Using postcore_initcall() makes the driver try to initialize way too
early.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a1b1e988 ]

25Mhz MCLK which was earlier used was of spread type.
Thus, we were not getting accurate rate. The 48Mhz system
clk is of non-spread type and we are changing to it to get
accurate rate.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit dadfab72 ]

Return value of request_irq() was irgnored. Fix this and report
the failure if any

Fixes: 6dc4fa17 ("ASoC: meson: add axg fifo base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e33ffbd9 ]

If the CPU DAI does not initialise rate_max, say if using
using KNOT or CONTINUOUS, then the rate_max field will be
initialised to 0. A value of zero in the rate_max field of
the hardware runtime will cause the sound card to support no
sample rates at all. Obviously this is not desired, just a
different mechanism is being used to apply the constraints. As
such update the setting of rate_max in dpcm_init_runtime_hw
to be consistent with the non-DPCM cases and set rate_max to
UINT_MAX if nothing is defined on the CPU DAI.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a5cd7e9c ]

devm_pinctrl_get will only return NULL in the case that pinctrl
is not built into the kernel and all the pinctrl functions used
by the DAPM core are appropriately stubbed for that case. There
is no need to error out of snd_soc_dapm_new_control_unlocked
if pinctrl isn't built into the kernel, so change the
IS_ERR_OR_NULL to just an IS_ERR.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9ea47d81 ]

Remove the "ice" prefix for the driver version string and bump version
to 0.7.1-k.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4f36cb36 ]

The GFS2_RDF_UPTODATE flag in the rgrp is used to determine when
a rgrp buffer is valid. It's cleared when the glock is invalidated,
signifying that the buffer data is now invalid. But before this
patch, function update_rgrp_lvb was setting the flag when it
determined it had a valid lvb. But that's an invalid assumption:
just because you have a valid lvb doesn't mean you have valid
buffers. After all, another node may have made the lvb valid,
and this node just fetched it from the glock via dlm.

Consider this scenario:
1. The file system is mounted with RGRPLVB option.
2. In gfs2_inplace_reserve it locks the rgrp glock EX, but thanks
   to GL_SKIP, it skips the gfs2_rgrp_bh_get.
3. Since loops == 0 and the allocation target (ap->target) is
   bigger than the largest known chunk of blocks in the rgrp
   (rs->rs_rbm.rgd->rd_extfail_pt) it skips that rgrp and bypasses
   the call to gfs2_rgrp_bh_get there as well.
4. update_rgrp_lvb sees the lvb MAGIC number is valid, so bypasses
   gfs2_rgrp_bh_get, but it still sets sets GFS2_RDF_UPTODATE due
   to this invalid assumption.
5. The next time update_rgrp_lvb is called, it sees the bit is set
   and just returns 0, assuming both the lvb and rgrp are both
   uptodate. But since this is a smaller allocation, or space has
   been freed by another node, thus adjusting the lvb values,
   it decides to use the rgrp for allocations, with invalid rd_free
   due to the fact it was never updated.

This patch changes update_rgrp_lvb so it doesn't set the UPTODATE
flag anymore. That way, it has no choice but to fetch the latest
values.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fd2a9817 ]

Once reset is issued, the driver loses all control queue interfaces.
Exercising control queue operations during reset is incorrect and
may result in long timeouts.

This patch introduces a new field 'reset_ongoing' in the hw structure.
This is set to 1 by the core driver when it receives a reset interrupt.
ice_sq_send_cmd checks reset_ongoing before actually issuing the control
queue operation. If a reset is in progress, it returns a soft error code
(ICE_ERR_RESET_PENDING) to the caller. The caller may or may not have to
take any action based on this return. Once the driver knows that the
reset is done, it has to set reset_ongoing back to 0. This will allow
control queue operations to be posted to the hardware again.

This "bail out" logic was specifically added to ice_sq_send_cmd (which
is pretty low level function) so that we have one solution in one place
that applies to all types of control queues.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ff2b1321 ]

Align Request Resource Ownership AQ command (0x0008) to the latest
specification. This includes:

- Correcting the resource IDs for the Global Cfg and Change locks.
- new enum ICE_CHANGE_LOCK_RES_ID
- new enum ICE_GLOBAL_CFG_LOCK_RES_ID
- Altering the flow for Global Config Lock to allow only the first PF to
  download the package.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 34d5629d ]

Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.

There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4405b632 ]

Check rx_buff_mgmt is allocated before accessing its internal fields.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit df2b5388 ]

In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 596bdbcc ]

use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9a65064a ]

Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d9c52fd1 ]

Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 58da3b42 ]

WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.

Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b8e13154 ]

snd_seq_system_client_init() doesn't check the errors returned from
its port creations.  Let's do it properly and handle the error paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7417844b ]

When REGULATORY_COUNTRY_IE_IGNORE is set,  __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().

After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().

To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.

Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 962341b5 ]

When we have first case to fall through it's not enough to put
single comment there to satisfy compiler. Instead of doing that,
return fall back value directly from default case.

This to avoid following warnings:

drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’:
include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
  _dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’
   dev_warn(ext->dev,
   ^~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here
  case CHT_WC_USBSRC_TYPE_SDP:
  ^~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1e28dbbe ]

da8xx_rproc_mem size is of type size_t, so use %zx to format the debug
print of it to avoid a compile warning.
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c856618d ]

The ID for RV8803 must be rv_8803
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 777d8ae5 ]

devm_kcalloc() returns NULL, it never returns error pointers.  In the
current code we would return PTR_ERR(NULL) which is success, instead of
returning the -ENOMEM error code.

Fixes: a0a1a1ba ("rtc: sysfs: facilitate attribute add to rtc device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 10af10db ]

Fix a typo. No functional change made by this patch.
Signed-off-by: Jay Foster <jayfoster@ieee.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 441f61e3 ]

Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB
I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2
hardware user manuals.

See also commit e9f0089b ("arm64: dts: r8a7795: Correct SATA
device size to 2MiB").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 33e26418 ]

get_seconds() and do_gettimeofday() are only used by a few modules now any
more (waiting for the respective patches to get accepted), and they are
among the last holdouts of code that is not y2038 safe in the core kernel.

Move the implementation into the timekeeping32.h header to clean up
the core kernel and isolate the old interfaces further.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6ff7705d ]

On p2180 sdmmc4 is powered from a fixed 1.8 V regulator.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 13136a47 ]

Implement support for the PMC_IMPL_E_33V_PWR register which replaces
PMC_PWR_DET register interface of the SoC generations preceding
Tegra186. Also add the voltage bit offsets to the tegra186_io_pads[]
table and the AO_HV pad.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6f128fa4 ]

The "frames" variable is unsigned so the error handling doesn't work
properly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 480f58cd ]

According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 93366b49 ]

The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.

While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.

So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 09b964af ]

The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e1c815f4 ]

In case of error, we can dereference uninitialized 'adev'

drivers/soundwire/intel_init.c:154 sdw_intel_acpi_cb()
error: uninitialized symbol 'adev'.

Fix that by not using adev for warn print and make it pr_err.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a306a0e4 ]

Deferred messages are async messages used to synchronize
transitions mostly while doing a bank switch on multi links.
On successful transitions these messages are marked complete
and thereby confirming that all the buses performed bank switch
successfully.

So, initialize the completion structure for the same.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 58c0f798 ]

Currently the register offset of the PWM bus gate in Allwinner H6 clock
driver is wrong.

Fix this issue.

Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Rongyi Chen <chenyi@tt-cool.com>
[Icenowy: refactor commit message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>