WM8994 chip has built-in regulators, which might be used for chip
operation. They are controlled by a separate wm8994-regulator driver,
which should be loaded before this driver calls regulator_get(), because
that driver also provides consumer-supply mapping for the them. If that
driver is not yet loaded, regulator core substitute them with dummy
regulator, what breaks chip operation, because the built-in regulators are
never enabled. Fix this by annotating this driver with MODULE_SOFTDEP()
"pre" dependency to "wm8994_regulator" module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The MT6397 mfd includes a pin controller. Add binding
a description for it.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify 'struct property_entry *properties' in mfd_cell.
It is always passed around as a pointer const struct.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The spi_register_driver() will set the spi_bus_type for the spi_driver,
thus remove the redundant setting in this driver.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It appears that preliminary documentation has a typo in the ID list,
i.e. LPSS UART #2 had been advertised wrongly.

Fix the driver according to the EDS v0.9.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Based on the file name and code of the driver, it is likely that this
module is related to TQMx86 and not TQx86.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix sparse warning:

drivers/mfd/stpmic1.c:62:28: warning:
 symbol 'stpmic1_regmap_config' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-x86-usb-watchdog-5.8', 'ib-mfd-power-rtc-5.8', 'ib-mfd-iio-power-5.8' and 'ib-mfd-hwmon-5.8' into ibs-for-mfd-merged

Add MAINTAINERS entry for Monolithic Power Systems mp2629 Charger driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Allows the user to compensate the intrinsic resistance of the battery
to accelerate the charging cycle.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The mp2629 provides switching-mode battery charge management for
single-cell Li-ion or Li-polymer battery. Driver supports the
access/control input source and battery charging parameters.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for 8-bit resolution ADC readings for input power
supply and battery charging measurement. Provides voltage, current
readings to mp2629 power supply driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mp2629 is a highly-integrated switching-mode battery charge management
device for single-cell Li-ion or Li-polymer battery.

Add MFD core enables chip access for ADC driver for battery readings,
and a power supply battery-charger driver
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add device tree binding information for mp2629 mfd driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This add support for the MediaTek MT6358 RTC. Driver using
compatible data to store different RTC_WRTGR address offset.
This replace RTC_WRTGR to RTC_WRTGR_MT6323 in mt6323-poweroff
driver which only needed by armv7 CPU without ATF.
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This adds support for the MediaTek MT6358 PMIC. This is a
multifunction device with the following sub modules:

- Regulator
- RTC
- Codec
- Interrupt

It is interfaced to the host controller using SPI interface
by a proprietary hardware called PMIC wrapper or pwrap.
MT6358 MFD is a child device of the pwrap.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This adds compatible for the MediaTek MT6358 PMIC.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add new struct members for mfd-cells and irq initial function, so we can
call devm_mfd_add_devices() only once.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Some pmics don't need backup interrupt settings, so we change to use
pm notifier for the pmics which are necessary to store settings.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Gateworks System Controller (GSC) is an I2C slave controller
implemented with an MSP430 micro-controller whose firmware embeds the
following features:
 - I/O expander (16 GPIO's) using PCA955x protocol
 - Real Time Clock using DS1672 protocol
 - User EEPROM using AT24 protocol
 - HWMON using custom protocol
 - Interrupt controller with tamper detect, user pushbotton
 - Watchdog controller capable of full board power-cycle
 - Power Control capable of full board power-cycle

see http://trac.gateworks.com/wiki/gsc for more details
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds documentation of device-tree bindings for the
Gateworks System Controller (GSC).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The driver lives now under MFD so split the current entry into two parts
and add me as co-maintainer of the Intel Broxton PMC driver. While there
correct formatting of Zha Qipeng's email address.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.

MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.

The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add new function that allows telemetry modules to get pointer to the
platform specific configuration. This is needed to allow the telemetry
debugfs module to fetch PMC IPC instance in the subsequent patch.

This also allows us to replace telemetry_pltconfig_valid() with
telemetry_get_pltdata() as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The PCI probe driver in intel_pmc_ipc.c is a duplicate of what we
already have in intel_scu_pcidrv.c with the exception that the later also
creates SCU specific devices. Move the PCI IDs from the intel_pmc_ipc.c
to intel_scu.c and use driver_data to detect whether SCU devices need to
be created or not.

Also update Kconfig entry to mention all platforms supported by the
Intel SCU PCI driver and change dependency from X86_INTEL_MID to PCI
which is more generic.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This allows to call the functions even when CONFIG_X86_INTEL_MID is not
enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Now that all callers have been converted over to the SCU IPC API we can
drop intel_pmc_ipc_command().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the driver to use the new SCU IPC API. This allows us to get rid
of the duplicate PMC IPC implementation which is now covered in SCU IPC
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the Intel Apollo Lake telemetry driver to use the new SCU IPC
API. This allows us to get rid of the duplicate PMC IPC implementation
which is now covered in SCU IPC driver.

Also move telemetry specific IPC message constant to the telemetry
driver where it belongs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This converts the Intel Merrifield PMIC driver over the new SCU IPC API
where the SCU IPC instance is passed to the functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the Intel Broxton Whiskey Cover PMIC driver to use the new SCU
IPC API. This allows us to get rid of the PMC IPC implementation which
is now covered in SCU IPC driver. We drop the error log if the IPC
command fails because intel_scu_ipc_dev_command() does that already.

Also move PMIC specific IPC message constants to the PMIC driver from
the intel_pmc_ipc.h header.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Both PMIC drivers (intel_soc_pmic_mrfld and intel_soc_pmic_bxtwc) will
be using this field going forward to access the SCU IPC instance.

While there add kernel-doc for the intel_soc_pmic structure.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

SCU IPC is pretty much the same IPC implemented in the intel_pmc_ipc
driver so drop the duplicate implementation and call directly the SCU
IPC.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Drivers such as intel_pmc_ipc.c can be unloaded as well so in order to
support those in this driver add a new function that can be called to
unregister the SCU IPC when it is not needed anymore.

We also add a managed version of the intel_scu_ipc_register() that takes
care of calling intel_scu_ipc_unregister() automatically when the driver
is unbound.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the IPC util to use the new SCU IPC API where the SCU IPC
instance is passed to the functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This converts the Intel MID watchdog driver over the new SCU IPC API
where the SCU IPC instance is passed to the functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This converts the power button driver to use the new SCU IPC API where
the SCU IPC instance is passed to the functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>