The Kconfig for this driver is currently:

config GPIO_MB86S7X
        bool "GPIO support for Fujitsu MB86S7x Platforms"

...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

config GPIO_BCM_KONA
        bool "Broadcom Kona GPIO"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Ray Jui <rjui@broadcom.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs)
which is configured through SuperIO register 0xd2 (output enable) and
0xd3 (simple I/O). This is also the reason why io_size is larger than
on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th
GPIO block.

I am also not sure about not configuring the Simple I/O registers as the
hardware I have only uses GPIO block 8. Reading back the values of
0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all
have 0xff set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

lsgpio.c: In function ‘main’:
lsgpio.c:166:7: warning: ‘device_name’ may be used uninitialized in this functio
n [-Wmaybe-uninitialized]
   ret = list_device(device_name);
       ^
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Cc: devicetree@vger.kernel.org
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

- Add GPIO support for Broadcom Vulcan ARM64.
- Add depends on ARCH_VULCAN to Kconfig to enable gpio controller
  driver for Broadcom Vulcan ARM64 SoCs.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The interrupt for the corresponding pin is configured to trigger when the
pin state changes compared to a preconfigured state (Bit set in INTCON).
This state is set by setting/clearing the bit in DEFVAL.
In the interrupt handler we need also to check if the bit in INTCON is set
for level triggered interrupts.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Update the NXP GPIO node dt-binding file for QorIQ and
Layerscape platforms, and add one more example with
ls2080a GPIO node.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The chip is also an 8 bit shift register which works out of the box as a GPO
expander with this patch
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Current code calls irq_domain_alloc_irqs_parent() in .alloc,
so it should call irq_domain_free_irqs_parent() accordingly in .free.
Fix it by switching to use irq_domain_free_irqs_common() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Export irq_domain_free_irqs_common so it can be used by modules.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

commit 0d36fe65
"powerpc: ppc4xx: use gpiochip data pointer"
made the mm_gc local variable in ppc4xx_gpio_set()
redundant, and when GCC treats warnings as errors this
happens:

arch/powerpc/sysdev/ppc4xx_gpio.c: In function 'ppc4xx_gpio_set':
arch/powerpc/sysdev/ppc4xx_gpio.c:93:26: error:
  unused variable 'mm_gc' [-Werror=unused-variable]
     struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
                             ^
   cc1: all warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.

Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.

Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds a new ACPI HID, AMDIF030, in the pt_gpio_acpi_match.

Signed-off-by: YD Tseng<Yd_Tseng@asmedia.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use gpio-generic to simplify this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: YD Tseng <Yd_Tseng@asmedia.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When using the GPIOLIB_IRQCHIP the gpiolib provides a
straight-forward implementation of request/release resources,
rely on that instead.

Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This switches the mcp23s08 driver to use the gpiolib irqchip
helpers.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This allows to set multiple outputs using a single SPI transfer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This allows to set multiple outputs using a single register write.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Set it once is enough, so remove the second platform_set_drvdata() call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

No need to store *medv in struct men_z127_gpio.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull Ceph updates from Sage Weil:
 "There is quite a bit here, including some overdue refactoring and
  cleanup on the mon_client and osd_client code from Ilya, scattered
  writeback support for CephFS and a pile of bug fixes from Zheng, and a
  few random cleanups and fixes from others"

[ I already decided not to pull this because of it having been rebased
  recently, but ended up changing my mind after all.  Next time I'll
  really hold people to it.  Oh well.   - Linus ]

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (34 commits)
  libceph: use KMEM_CACHE macro
  ceph: use kmem_cache_zalloc
  rbd: use KMEM_CACHE macro
  ceph: use lookup request to revalidate dentry
  ceph: kill ceph_get_dentry_parent_inode()
  ceph: fix security xattr deadlock
  ceph: don't request vxattrs from MDS
  ceph: fix mounting same fs multiple times
  ceph: remove unnecessary NULL check
  ceph: avoid updating directory inode's i_size accidentally
  ceph: fix race during filling readdir cache
  libceph: use sizeof_footer() more
  ceph: kill ceph_empty_snapc
  ceph: fix a wrong comparison
  ceph: replace CURRENT_TIME by current_fs_time()
  ceph: scattered page writeback
  libceph: add helper that duplicates last extent operation
  libceph: enable large, variable-sized OSD requests
  libceph: osdc->req_mempool should be backed by a slab pool
  libceph: make r_request msg_size calculation clearer
  ...

Pull orangefs filesystem from Mike Marshall.

This finally merges the long-pending orangefs filesystem, which has been
much cleaned up with input from Al Viro over the last six months.  From
the documentation file:

 "OrangeFS is an LGPL userspace scale-out parallel storage system.  It
  is ideal for large storage problems faced by HPC, BigData, Streaming
  Video, Genomics, Bioinformatics.

  Orangefs, originally called PVFS, was first developed in 1993 by Walt
  Ligon and Eric Blumer as a parallel file system for Parallel Virtual
  Machine (PVM) as part of a NASA grant to study the I/O patterns of
  parallel programs.

  Orangefs features include:

    - Distributes file data among multiple file servers
    - Supports simultaneous access by multiple clients
    - Stores file data and metadata on servers using local file system
      and access methods
    - Userspace implementation is easy to install and maintain
    - Direct MPI support
    - Stateless"

see Documentation/filesystems/orangefs.txt for more in-depth details.

* tag 'ofs-pull-tag-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux: (174 commits)
  orangefs: fix orangefs_superblock locking
  orangefs: fix do_readv_writev() handling of error halfway through
  orangefs: have ->kill_sb() evict the VFS side of things first
  orangefs: sanitize ->llseek()
  orangefs-bufmap.h: trim unused junk
  orangefs: saner calling conventions for getting a slot
  orangefs_copy_{to,from}_bufmap(): don't pass bufmap pointer
  orangefs: get rid of readdir_handle_s
  ornagefs: ensure that truncate has an up to date inode size
  orangefs: move code which sets i_link to orangefs_inode_getattr
  orangefs: remove needless wrapper around GFP_KERNEL
  orangefs: remove wrapper around mutex_lock(&inode->i_mutex)
  orangefs: refactor inode type or link_target change detection
  orangefs: use new getattr for revalidate and remove old getattr
  orangefs: use new getattr in inode getattr and permission
  orangefs: use new orangefs_inode_getattr to get size in write and llseek
  orangefs: use new orangefs_inode_getattr to create new inodes
  orangefs: rename orangefs_inode_getattr to orangefs_inode_old_getattr
  orangefs: remove inode->i_lock wrapper
  orangefs: put register_chrdev immediately before register_filesystem
  ...

Pull NTB bug fixes from Jon Mason:
 "NTB bug fixes for tasklet from spinning forever, link errors,
  translation window setup, NULL ptr dereference, and ntb-perf errors.

  Also, a modification to the driver API that makes _addr functions
  optional"

* tag 'ntb-4.6' of git://github.com/jonmason/ntb:
  NTB: Remove _addr functions from ntb_hw_amd
  NTB: Make _addr functions optional in the API
  NTB: Fix incorrect clean up routine in ntb_perf
  NTB: Fix incorrect return check in ntb_perf
  ntb: fix possible NULL dereference
  ntb: add missing setup of translation window
  ntb: stop link work when we do not have memory
  ntb: stop tasklet from spinning forever during shutdown.
  ntb: perf test: fix address space confusion

Pull more SCSI updates from James Bottomley:
 "The only new stuff which missed the first pull request is an update to
  the UFS driver.

  The rest is an assortment of bug fixes and minor tweaks which appeared
  recently (some are fixes for recent code and some are stuff spotted
  recently by the checkers or the new gcc-6 compiler [most of Arnd's
  stuff])"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
  scsi_common: do not clobber fixed sense information
  scsi: ufs: select CONFIG_NLS
  scsi: fc: use get/put_unaligned64 for wwn access
  fnic: move printk()s outside of the critical code section.
  qla2xxx: avoid maybe_uninitialized warning
  megaraid_sas: add missing curly braces in ioctl handler
  lpfc: fix misleading indentation
  scsi_transport_sas: add 'scsi_target_id' sysfs attribute
  scsi_dh_alua: uninitialized variable in alua_check_vpd()
  scsi: ufs-qcom: add printouts of testbus debug registers
  scsi: ufs-qcom: enable/disable the device ref clock
  scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup
  scsi: ufs: add device quirk delay before putting UFS rails in LPM
  scsi: ufs: fix leakage during link off state
  scsi: ufs: tune UniPro parameters to optimize hibern8 exit time
  scsi: ufs: handle non spec compliant bkops behaviour by device
  scsi: ufs: add retry for query descriptors
  scsi: ufs: add error recovery after DL NAC error
  scsi: ufs: make error handling bit faster
  scsi: ufs: disable vccq if it's not needed by UFS device
  ...