TI LMU (Lighting Management Unit) driver supports lighting devices below.

  LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.

LMU devices have common features.
  - I2C interface for accessing device registers
  - Hardware enable pin control
  - Backlight brightness control
  - Notifier for hardware fault monitoring
  - Regulators for LCD display bias

It contains fault monitor, backlight, LED and regulator driver.

LMU fault monitor
-----------------
  LM3633 and LM3697 provide hardware monitoring feature.
  It enables open or short circuit detection.
  After monitoring is done, each device should be re-initialized.
  Notifier is used for this case.
  Separate patch for 'ti-lmu-fault-monitor' will be sent later.

Backlight
---------
  It's handled by TI LMU backlight consolidated driver and
  chip dependent data. Separate patchset will be sent later.

LED indicator
-------------
  LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
  supported. Separate patch for 'leds-lm3633' will be sent later.

Regulator
---------
  LM3631 has 5 regulators for the display bias.
  LM3632 supports 3 regulators. One consolidated driver enables it.
  The lm363x regulator driver is already upstreamed.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch describes overall binding for TI LMU MFD devices.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. This patch lets the driver use the new device tree property
"xpowers,master-mode" to set the correct operating mode for the board.

Fixes: 8824ee85 ("mfd: axp20x: Add support for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. To let the device tree describe which mode of operation is needed,
this patch introduces a new property "xpowers,master-mode".

Fixes: 204ae296 ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Since commit 845c8770 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") I2C core assigns interrupt line to I2C slave
devices with regarding to GpioInt() resources.

There is no need to repeat this in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

STM32 timers register bank size is 0x400. Fix regmap max_register.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It is a debugging statement so make it be issued only then.

No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

At least two different omap3630/3730 boards booting from MMC1
fail to reboot if the "ti,twl4030-power-idle-osc-off" or
"ti,twl4030-power-idle" compatible flags are set.  This patch will
keep the vmmc1 powered up during reboot allowing the bootloader
to load.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add missing of_platform_depopulate() upon driver removal.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patches adds the first minimal support to the upstream Linux tree.
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch installs an ACPI GPE handler for LID0 ACPI device to indicate
ACPI core that this GPE should stay enabled for lid to work in suspend
to idle path.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-gpio-4.12', 'ib-mfd-iio-input-4.12', 'ib-mfd-input-4.12', 'ib-mfd-leds-4.12', 'ib-mfd-phy-4.12' and 'ib-mfd-pinctrl-samsung-4.12' into ibs-for-mfd-merged

Motorola CPCAP is a PMIC found in multiple smartphones.
This driver adds support for the power/on button and has
been tested in Droid 4.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

CPCAP can sense if IRQ is currently set or not. This
functionality is required for a few subdevices, such
as the power button and usb phy modules.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This fixes compilation for files, that try to include the
cpcap header in alphabetically sorted #include lists.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds support for retention control for Exynos5433 SoCs. Three
groups of pins has been defined for retention control: common shared group
for ALIVE, CPIF, eSE, FINGER, IMEM, NFC, PERIC, TOUCH pin banks and
separate control for FSYS and AUD pin banks, for which PMU retention
registers match whole banks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

When pin controller device is a part of power domain, there is no guarantee
that the power domain was not turned off and then on during boot process
before probing of the pin control driver. If it happened, then pin control
driver should ensure that pad retention is turned off during its probe call.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

The bindings, which are now used in MFD, need also to be
documented in the MFD binding document.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Since the driver has been split into MFD there is no reason for it to
stay, so remove it.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add 4-wire/5-wire touchscreen controller.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for sixteen-channel 12-bit resolution ADC and its functions,
which include general-purpose ADC readings, battery voltage measurement,
and die temperature measurement.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add core files for low resolution analog-to-digital converter (mxs-lradc)
MFD driver.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add a device tree binding document for the wm831x series of PMICs.
Currently only support for the registering the device and the GPIOs are
actually implemented in the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Now the wm831x-core has basic DT support we can update this driver to
allow use of the GPIOs within a device tree system.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the basic ability to register the device through device tree, more
work is needed to get each individual sub-driver functioning correctly
but this is enough to get the device to probe from device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The MFD-specific header will go away because it duplicates defines from
exynos-regs-pmu.h.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...

Pull more KVM updates from Radim Krčmář:
 "Second batch of KVM changes for the 4.11 merge window:

  PPC:
   - correct assumption about ASDR on POWER9
   - fix MMIO emulation on POWER9

  x86:
   - add a simple test for ioperm
   - cleanup TSS (going through KVM tree as the whole undertaking was
     caused by VMX's use of TSS)
   - fix nVMX interrupt delivery
   - fix some performance counters in the guest

  ... and two cleanup patches"

* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Fix pending events injection
  x86/kvm/vmx: remove unused variable in segment_base()
  selftests/x86: Add a basic selftest for ioperm
  x86/asm: Tidy up TSS limit code
  kvm: convert kvm.users_count from atomic_t to refcount_t
  KVM: x86: never specify a sample period for virtualized in_tx_cp counters
  KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
  KVM: PPC: Book3S HV: Fix software walk of guest process page tables

Pull documentation fixes from Jonathan Corbet:
 "A few fixes for the docs tree, including one for a 4.11 build
  regression"

* tag 'docs-4.11-fixes' of git://git.lwn.net/linux:
  Documentation/sphinx: fix primary_domain configuration
  docs: Fix htmldocs build failure
  doc/ko_KR/memory-barriers: Update control-dependencies section
  pcieaer doc: update the link
  Documentation: Update path to sysrq.txt

Pull staging/IIO driver fixes from Greg KH:
 "Here are a few small staging and IIO driver fixes for issues that
  showed up after the big set if changes you merged last week.

  Nothing major, just small bugs resolved in some IIO drivers, a lustre
  allocation fix, and some RaspberryPi driver fixes for reported
  problems, as well as a MAINTAINERS entry update.

  All of these have been in linux-next for a week with no reported
  issues"

* tag 'staging-4.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: fsl-mc: fix warning in DT ranges parser
  MAINTAINERS: Remove Noralf Trønnes as fbtft maintainer
  staging: vchiq_2835_arm: Make cache-line-size a required DT property
  staging: bcm2835/mmal-vchiq: unlock on error in buffer_from_host()
  staging/lustre/lnet: Fix allocation size for sv_cpt_data
  iio: adc: xilinx: Fix error handling
  iio: 104-quad-8: Fix off-by-one error when addressing flag register
  iio: adc: handle unknow of_device_id data

Pull crypto fixes from Herbert Xu:

 - vmalloc stack regression in CCM

 - Build problem in CRC32 on ARM

 - Memory leak in cavium

 - Missing Kconfig dependencies in atmel and mediatek

 - XTS Regression on some platforms (s390 and ppc)

 - Memory overrun in CCM test vector

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: vmx - Use skcipher for xts fallback
  crypto: vmx - Use skcipher for cbc fallback
  crypto: testmgr - Pad aes_ccm_enc_tv_template vector
  crypto: arm/crc32 - add build time test for CRC instruction support
  crypto: arm/crc32 - fix build error with outdated binutils
  crypto: ccm - move cbcmac input off the stack
  crypto: xts - Propagate NEED_FALLBACK bit
  crypto: api - Add crypto_requires_off helper
  crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
  crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
  crypto: cavium - fix leak on curr if curr->head fails to be allocated
  crypto: cavium - Fix couple of static checker errors

Pull misc final vfs updates from Al Viro:
 "A few unrelated patches that got beating in -next.

  Everything else will have to go into the next window ;-/"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  hfs: fix hfs_readdir()
  selftest for default_file_splice_read() infoleak
  9p: constify ->d_name handling

Pull more SCSI updates from James Bottomley:
 "This is the set of stuff that didn't quite make the initial pull and a
  set of fixes for stuff which did.

  The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
  cover a lot of previously submitted stuff, the most important of which
  probably covers some of the failing irq vectors allocation and other
  fallout from having the SCSI command allocated as part of the block
  allocation functions"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
  scsi: qedi: Fix memory leak in tmf response processing.
  scsi: aacraid: remove redundant zero check on ret
  scsi: lpfc: use proper format string for dma_addr_t
  scsi: lpfc: use div_u64 for 64-bit division
  scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
  scsi: cciss: correct check map error.
  scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
  scsi: aacraid: Fixed expander hotplug for SMART family
  scsi: mpt3sas: switch to pci_alloc_irq_vectors
  scsi: qedf: fixup compilation warning about atomic_t usage
  scsi: remove scsi_execute_req_flags
  scsi: merge __scsi_execute into scsi_execute
  scsi: simplify scsi_execute_req_flags
  scsi: make the sense header argument to scsi_test_unit_ready mandatory
  scsi: sd: improve TUR handling in sd_check_events
  scsi: always zero sshdr in scsi_normalize_sense
  scsi: scsi_dh_emc: return success in clariion_std_inquiry()
  scsi: fix memory leak of sdpk on when gd fails to allocate
  scsi: sd: make sd_devt_release() static
  scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
  ...

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Missing check for full sock in ip_route_me_harder(), from
   Florian Westphal.

2) Incorrect sip helper structure initilization that breaks it when
   several ports are used, from Christophe Leroy.

3) Fix incorrect assumption when looking up for matching with adjacent
   intervals in the nft_set_rbtree.

4) Fix broken netlink event error reporting in nf_tables that results
   in misleading ESRCH errors propagated to userspace listeners.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "A fix and regression test case for nvdimm namespace label
  compatibility.

  Details:

   - An "nvdimm namespace label" is metadata on an nvdimm that
     provisions dimm capacity into a "namespace" that can host a block
     device / dax-filesytem, or a device-dax character device.

     A namespace is an object that other operating environment and
     platform firmware needs to comprehend for capabilities like booting
     from an nvdimm.

     The label metadata contains a checksum that Linux was not
     calculating correctly leading to other environments rejecting the
     Linux label.

   These have received a build success notification from the kbuild
   robot, and a positive test result from Nick who reported the problem"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit, libnvdimm: fix interleave set cookie calculation
  tools/testing/nvdimm: make iset cookie predictable

Pull PCI fixes from Bjorn Helgaas:

 - fix NULL pointer dereferences in many DesignWare-based drivers due to
   refactoring error

 - fix Altera config write breakage due to my refactoring error

* tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: altera: Fix TLP_CFG_DW0 for TLP write
  PCI: dwc: Fix crashes seen due to missing assignments

Pull parisc fixes and cleanups from Helge Deller:
 "Nothing really important in this patchset: fix resource leaks in error
  paths, coding style cleanups and code removal"

* 'parisc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Remove flush_user_dcache_range and flush_user_icache_range
  parisc: fix a printk
  parisc: ccio-dma: Handle return NULL error from ioremap_nocache
  parisc: Define access_ok() as macro
  parisc: eisa: Fix resource leaks in error paths
  parisc: eisa: Remove coding style errors

Pull Xtensa updates from Max Filippov:

 - clean up bootable image build targets: provide separate 'Image',
   'zImage' and 'uImage' make targets that only build corresponding
   image type. Make 'all' build all images appropriate for a platform

 - allow merging vectors code into .text section as a preparation step
   for XIP support

 - fix handling external FDT when the kernel is built without
   BLK_DEV_INITRD support

* tag 'xtensa-20170303' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: allow merging vectors into .text section
  xtensa: clean up bootable image build targets
  xtensa: move parse_tag_fdt out of #ifdef CONFIG_BLK_DEV_INITRD