When we're handling TO_EXCLUDE report in EXCLUDE filter mode we should
not ignore the return value of __grp_src_toex_excl() as we'll miss
sending notifications about group changes.

Fixes: 5bf1e00b ("net: bridge: mcast: support for IGMPV3/MLDv2 CHANGE_TO_INCLUDE/EXCLUDE report")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support to --show-ring & --set-ring Ethtool functions:
- Adding min, max, power of two check to new ring parameter's value.
- Bring down the network interface before changing the value of ring
  parameters.
- Bring up the network interface after changing the value of ring
  parameters.
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Refactor headroom management

Petr says:

On Spectrum, port buffers, also called port headroom, is where packets are
stored while they are parsed and the forwarding decision is being made. For
lossless traffic flows, in case shared buffer admission is not allowed,
headroom is also where to put the extra traffic received before the sent
PAUSE takes effect. Another aspect of the port headroom is the so called
internal buffer, which is used for egress mirroring.

Linux supports two DCB interfaces related to the headroom: dcbnl_setbuffer
for configuration, and dcbnl_getbuffer for inspection. In order to make it
possible to implement these interfaces, it is first necessary to clean up
headroom handling, which is currently strewn in several places in the
driver.

The end goal is an architecture whereby it is possible to take a copy of
the current configuration, adjust parameters, and then hand the proposed
configuration over to the system to implement it. When everything works,
the proposed configuration is accepted and saved. First, this centralizes
the reconfiguration handling to one function, which takes care of
coordinating buffer size changes and priority map changes to avoid
introducing drops. Second, the fact that the configuration is all in one
place makes it easy to keep a backup and handle error path rollbacks, which
were previously hard to understand.

Patch #1 introduces struct mlxsw_sp_hdroom, which will keep port headroom
configuration.

Patch #2 unifies handling of delay provision between PFC and PAUSE. From
now on, delay is to be measured in bytes of extra space, and will not
include MTU. PFC handler sets the delay directly from the parameter it gets
through the DCB interface. For PAUSE, MLXSW_SP_PAUSE_DELAY is converted to
have the same meaning.

In patches #3-#5, MTU, lossiness and priorities are gradually moved over to
struct mlxsw_sp_hdroom.

In patches #6-#11, handling of buffer resizing and priority maps is moved
from spectrum.c and spectrum_dcb.c to spectrum_buffers.c. The API is
gradually adapted so that struct mlxsw_sp_hdroom becomes the main interface
through which the various clients express how the headroom should be
configured.

Patch #12 is a small cleanup that the previous transformation made
possible.

In patch #13, the port init code becomes a boring client of the headroom
code, instead of rolling its own thing.

Patches #14 and #15 move handling of internal mirroring buffer to the new
headroom code as well. Previously, this code was in the SPAN module. This
patchset converts the SPAN module to another boring client of the headroom
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Traffic mirroring modes that are in-chip implemented on egress need an
internal buffer to work. As the only client, the SPAN module was managing
the buffer so far. However logically it belongs to the buffers module. E.g.
buffer size validation needs to take the size of the internal buffer into
account.

Therefore move the related code from SPAN to spectrum_buffers. Move over
the callbacks that determine the minimum buffer size as a function of
maximum speed and MTU. Add a field describing the internal buffer to struct
mlxsw_sp_hdroom. Extend mlxsw_sp_hdroom_bufs_reset_sizes() to take care of
sizing the internal buffer as well. Change the SPAN module to invoke that
function and mlxsw_sp_hdroom_configure() like all the other hdroom clients.
Drop the now-unnecessary mlxsw_sp_span_port_buffer_disable().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The size of the internal buffer is currently calculated in the SPAN module.
Logically it belongs to the spectrum_buffers module, where it should be
moved. However, that being a chip-specific operation, it needs dynamic
dispatch. There currently is a chip-specific structure for description of
shared buffer values, struct mlxsw_sp_sb_vals. However placing ops into
this structure would be confusing. Therefore introduce a new per-chip
structure, currently empty, and initialize the ops pointer as appropriate.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently mlxsw_sp_port_headroom_init() configures both priomap and buffers
by hand. Additionally, for port buffers, it configures buffer 0 with a size
that it will never again have if PFC configuration is touched.

Rewrite the init code to become a client of the new hdroom code. The only
difference in invocation is that the configuration is forced, so that it is
issued even if the desired configuration happens to match what is contained
in (hitherto not initialized with meaningful values) mlxsw_sp_port->hdroom.

Since now mlxsw_sp_port_headroom_init() initializes all the PG buffers to
meaningful values, mlxsw_sp_hdroom_configure_buffers() can avoid querying
the current configuration, and can fill the whole PBMC itself.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is now only used from the buffers module, and is a trivial
field reference. Just inline it and drop the related artifacts.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move all the headroom code to the spectrum_buffers module, where it
belongs.

Rename mlxsw_sp_pg_buf_threshold_get() and mlxsw_sp_pg_buf_pack() to
..._hdroom_... to match the naming convention of the new headroom code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ETS handler performs the headroom configuration in three steps: first
it resizes the buffers and adds any new ones. Then it redirects priorities
to the new buffers. And finally it sets the size of the now-unused buffers
to zero. This way no packet drops are introduced.

This sort of careful approach will also be useful for configuring port
buffer sizes and priority map by hand, through dcbnl_setbuffer. Therefore
move the code from the DCB handler to the generic headroom function.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new hdroom code has certain conventions: iteration over priorities is
done through a variable named `prio', configuration is not pushed unless it
is dirty, but a `force' flag can be used to override this, updated
configuration is written to port. Convert the function
mlxsw_sp_port_pg_prio_map() to use these conventions and rename
appropriately to fit in.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ETS handler performs the headroom configuration in three steps: first
it resizes the buffers and adds any new ones. Then it redirects priorities
to the new buffers. And finally it sets the size of the now-unused buffers
to zero. This way no packet drops are introduced.

Both of the buffer size configuration operations are simply buffer size
configurations, there is no material difference between setting buffers to
zero and any other value. Therefore simply invoke the same
mlxsw_sp_hdroom_configure(), and drop mlxsw_sp_port_pg_destroy() and
mlxsw_sp_ets_has_pg() which are now unused.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split mlxsw_sp_port_headroom_set() to three functions.
mlxsw_sp_hdroom_bufs_reset_sizes() changes the sizes of the individual PG
buffers, and mlxsw_sp_hdroom_configure_buffers() will actually apply the
configuration. A third function, mlxsw_sp_hdroom_bufs_fit(), verifies that
the requested buffer configuration matches total headroom size
requirements.

Add wrappers, mlxsw_sp_hdroom_configure() and __..., that will eventually
perform full headroom configuration, but for now, only have them verify the
configured headroom size, and invoke mlxsw_sp_hdroom_configure_buffers().
Have them take the `force` argument to prepare for a later patch, even
though it is currently unused.

Note that the loop in mlxsw_sp_hdroom_configure_buffers() only goes through
DCBX_MAX_BUFFERS. Since there is no logic to configure the control buffer,
it needs to keep the values queried from the FW. Eventually this function
should configure all the PGs.

Note that conversion of __mlxsw_sp_dcbnl_ieee_setets() is not trivial. That
function performs the headroom configuration in three steps: first it
resizes the buffers and adds any new ones. Then it redirects priorities to
the new buffers. And finally it sets the size of the now-unused buffers to
zero. This way no packet drops are introduced.

So after invoking mlxsw_sp_hdroom_bufs_reset_sizes(), tweak the
configuration to keep the old sizes of PG buffers for those buffers whose
size was set to zero.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far, port buffers were always autoconfigured. When dcbnl_setbuffer
callback is implemented, it will allow the user to change the buffer size
configuration by hand. The sizes therefore need to be a configuration
parameter, not always deduced, and therefore belong to struct
mlxsw_sp_hdroom, where the configuration routine should take them from.

Update mlxsw_sp_port_headroom_set() to update these sizes. Have the
function update the sizes even for the case that a given buffer is not
used.

Additionally, change the loop iteration end to DCBX_MAX_BUFFERS instead of
IEEE_8021QAZ_MAX_TCS. The value is the same, but the semantics differ.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Client-side configuration has lossiness as an attribute of a priority.
Therefore add a "lossy" attribute to struct mlxsw_sp_hdroom_prio.

To a Spectrum ASIC, lossiness is a feature of a port buffer. Therefore add
struct mlxsw_sp_hdroom_buf, which in the following patches will get more
attributes, but right now only use it to track port buffer lossiness.

Instead of passing around the primary indicators of PFC and pause_en, add a
function mlxsw_sp_hdroom_bufs_reset_lossiness() to compute the buffer
lossiness from the priority map and priority lossiness. Change
mlxsw_sp_port_headroom_set() to take the buffer lossy flag from the
headroom configuration. Have the PFC and pause handlers configure priority
lossiness in mlxsw_sp_hdroom, from where it will propagate.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mapping from priorities to buffers determines which buffers should be
configured. Lossiness of these priorities combined with the mapping
determines whether a given buffer should be lossy.

Currently this configuration is stored implicitly in DCB ETS, PFC and
ethtool PAUSE configuration. Keeping it together with the rest of the
headroom configuration and deriving it as needed from PFC / ETS / PAUSE
will make things clearer. To that end, add a field "prios" to struct
mlxsw_sp_hdroom.

Previously, __mlxsw_sp_port_headroom_set() took prio_tc as an argument, and
assumed that the same mapping as we use on the egress should be used on
ingress as well. Instead, track this configuration at each priority, so
that it can be adjusted flexibly.

In the following patches, as dcbnl_setbuffer is implemented, it will need
to store its own mapping, and it will also be sometimes necessary to revert
back to the original ETS mapping. Therefore track two buffer indices: the
one for chip configuration (buf_idx), and the source one (ets_buf_idx).
Introduce a function to configure the chip-level buffer index, and for now
have it simply copy the ETS mapping over to the chip mapping.

Update the ETS handler to project prio_tc to the ets_buf_idx and invoke the
buf_idx recomputation.

Now that there is a canonical place to look for this configuration,
mlxsw_sp_port_headroom_set() does not need to invent def_prio_tc to use if
DCB is compiled out.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MTU influences sizes of auto-allocated buffers. Make it a part of port
buffer configuration and have __mlxsw_sp_port_headroom_set() take it from
there, instead of as an argument.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a priority is marked as lossless using DCB PFC, or when pause frames
are enabled on a port, mlxsw adds to port buffers an extra space to cover
the traffic that will arrive between the time that a pause or PFC frame is
emitted, and the time traffic actually stops. This is called the delay. The
concept is the same in PFC and pause, however the way the extra buffer
space is calculated differs.

In this patch, unify this handling. Delay is to be measured in bytes of
extra space, and will not include MTU. PFC handler sets the delay directly
from the parameter it gets through the DCB interface.

To convert pause handler, move MLXSW_SP_PAUSE_DELAY to ethtool module,
convert to bytes, and reduce it by maximum MTU, and divide by two. Then it
has the same meaning as the delay_bytes set by the PFC handler.

Keep the delay_bytes value in struct mlxsw_sp_hdroom introduced in the
previous patch. Change PFC and pause handlers to store the new delay value
there and have __mlxsw_sp_port_headroom_set() take it from there.

Instead of mlxsw_sp_pfc_delay_get() and mlxsw_sp_pg_buf_delay_get(),
introduce mlxsw_sp_hdroom_buf_delay_get() to calculate the delay provision.
Drop the unnecessary MLXSW_SP_CELL_FACTOR, and instead add an explanatory
comment describing the formula used.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port headroom handling is currently strewn across several modules and
tricky to follow: MTU, DCB PFC, DCB ETS and ethtool pause all influence the
settings, and then there is the completely separate initial configuraion in
spectrum_buffers. A following patch will implement the dcbnl_setbuffer
callback, which is going to further complicate the landscape.

In order to simplify work with port buffers, the following patches are
going to centralize all port-buffer handling in spectrum_buffers. As a
first step, introduce a (currently empty) struct mlxsw_sp_hdroom that will
keep the configuration parameters, and allocate and free it in appropriate
places.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-09-15

Various updates to mlx5 driver,

1) Eli adds support for TC trap action.
2) Eran, minor improvements to clock.c code structure
3) Better handling of error reporting in LAG from Jianbo
4) IPv6 traffic class (DSCP) header rewrite support from Maor
5) Ofer Levi adds support for CQE compression of multi-strides packets
6) Vu, Enables use of vport meta data by default.
7) Some minor code cleanup
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
nexthop: Small changes

This patch set contains a few small changes that I split out of the RFC
I sent last week [1]. Main change is the conversion of the nexthop
notification chain to a blocking chain so that it could be reused by
device drivers for nexthop objects programming in the future.

Tested with fib_nexthops.sh:

Tests passed: 164
Tests failed:   0

[1] https://lore.kernel.org/netdev/20200908091037.2709823-1-idosch@idosch.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c7cdbe2e ("vxlan: support for nexthop notifiers") registered
a listener in the VXLAN driver to the nexthop notification chain. Its
purpose is to cleanup FDB entries that use a nexthop that is being
deleted.

Test that such FDB entries are removed when the nexthop group that they
use is deleted. Test that entries are not deleted when a single nexthop
in the group is deleted.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the in-kernel delete notification is emitted from the error
path of nexthop_add() and replace_nexthop(), which can be confusing to
in-kernel listeners as they are not familiar with the nexthop.

Instead, only emit the notification when the nexthop is actually
deleted. The following sub-cases are covered:

1. User space deletes the nexthop
2. The nexthop is deleted by the kernel due to a netdev event (e.g.,
   nexthop device going down)
3. A group is deleted because its last nexthop is being deleted
4. The network namespace of the nexthop device is deleted
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the only listener of the nexthop notification chain is the
VXLAN driver. Subsequent patches will add more listeners (e.g., device
drivers such as netdevsim) that need to be able to block when processing
notifications.

Therefore, convert the notification chain to a blocking one. This is
safe as notifications are always emitted from process context.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used anywhere.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used or implemented anywhere.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As CHELSIO_INLINE_CRYPTO is bool, and CHELSIO_T4 is tristate, the
dependency of CHELSIO_INLINE_CRYPTO on CHELSIO_T4 is not sufficient to
protect CRYPTO_DEV_CHELSIO_TLS and CHELSIO_IPSEC_INLINE.  The latter two
are also tristate, hence if CHELSIO_T4=n, they cannot be builtin, as
that would lead to link failures like:

    drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c:259: undefined reference to `cxgb4_port_viid'

and

    drivers/net/ethernet/chelsio/inline_crypto/ch_ipsec/chcr_ipsec.c:752: undefined reference to `cxgb4_reclaim_completed_tx'

Fix this by re-adding dependencies on CHELSIO_T4 to tristate symbols.
The dependency of CHELSIO_INLINE_CRYPTO on CHELSIO_T4 is kept to avoid
asking the user.

Fixes: 6bd860ac ("chelsio/chtls: CHELSIO_INLINE_CRYPTO should depend on CHELSIO_T4")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

-trigger-test-event'

Ido Schimmel says:

====================
mlxsw: Introduce fw_fatal health reporter and test cmd to trigger test event

Jiri says:

This patch set introduces a health reporter for mlxsw that reports FW
fatal events. Alongside that, it introduces a test command that is used
to trigger a dummy FW fatal event by user:

$ sudo devlink health test pci/0000:03:00.0 reporter fw_fatal

$ devlink health
pci/0000:03:00.0:
  reporter fw_fatal
    state error error 1 recover 0 last_dump_date 2020-07-27 last_dump_time 16:33:27 auto_dump true

$ sudo devlink health dump show pci/0000:03:00.0 reporter fw_fatal -j -p
{
    "irisc_id": 0,
    "event": [
        "id": 3 ],
    "method": "query",
    "long_process": false,
    "command_type": "mad",
    "reg_attr_id": 0
}

As a dependency, the FW validation and flashing is moved to core.c.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce devlink health reporter to report FW fatal events. Implement
the event listener using MFDE trap and enable the events to be
propagated using MFGD register configuration.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a test command for health reporters. User might use this
command to trigger test event on a reporter if the reporter supports it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce MFGD register that is used to configure firmware debugging.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce MFDE register that is passed through MFDE trap in case of
fatal FW event.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the fw flashing code was moved to core.c, move the param which is
related to it there as well. Remove unnecessary parentheses on the way.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract the code calling params register/unregister driver ops into
separate functions. Call publish/unpublish unconditionally.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the firmware flashing is not specific to Spectrum, move the code to
core.c and avoid one op call and 2 exported symbols. Also, this allows
to do flash before call of driver->init function and possibly do other
core calls in between.

Do some small renaming here and there on the way to be consistent with
the rest of core.c code.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Among other changes, this version supports FW monitoring.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wong Vee Khee says:

====================
net: stmmac: Add ethtool support for get|set channels

This patch set is to add support for user to get or set Tx/Rx channel
via ethtool. There are two patches that fixes bug introduced on upstream
in order to have the feature work.

Tested on Intel Tigerlake Platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.

Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.

Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_set_real_num_tx_queues() & netif_set_real_num_rx_queues() should be
used to inform network stack about the real Tx & Rx queue (active) number
in both stmmac_open() and stmmac_resume(), therefore, we move the code
from stmmac_dvr_probe() to stmmac_hw_setup().

Fixes: c02b7a91 net: stmmac: use netif_set_real_num_{rx,tx}_queues
Signed-off-by: Aashish Verma <aashishx.verma@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restructure NAPI add and delete process so that we can call them
accordingly in open() and ethtool_set_channels() accordingly.

Introduced stmmac_reinit_queues() to handle the transition needed
for changing Rx & Tx channels accordingly.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
ethtool: add pause frame stats

This is the first (small) series which exposes some stats via
the corresponding ethtool interface. Here (thanks to the
excitability of netlink) we expose pause frame stats via
the same interfaces as ethtool -a / -A.

In particular the following stats from the standard:
 - 30.3.4.2 aPAUSEMACCtrlFramesTransmitted
 - 30.3.4.3 aPAUSEMACCtrlFramesReceived

4 real drivers are converted, I believe we got confirmation
from maintainers that all exposed stats match the standard.

v3:
 - fix mlx5 build
 - adjust the init logic in patch 1
v2:
 - netdevsim: add missing static
 - bnxt: fix sparse warning
 - mlx5: address Saeed's comments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>