The following parameters are no longer needed by the edma driver since the
information can be obtained from the IP's CCCFG register:
n_channel, n_region, n_slot and n_tc.
Remove the initialization of n_cc as well since in this context it has no
meaning. We have separate edma_soc_info struct/eDMA3_CC instance so this
member does not make any sense (and the driver no longer uses it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE

The ti,edma-regions; ti,edma-slots and dma-channels in DT are
redundant since the very same information can be obtained from the HW.
The mentioned properties are deprecated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE

In case when booted with DT or the queue_priority_mapping is not provided
set up a default priority map.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

To be consistent in the code that we take parameters from edma_cc[j] struct
and not randomly from info[j] as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

The struct edma is allocated per CC bases so the member num_cc does not make
any sense. One CC is one CC, it does not have sub CCs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

It is no longer in use by the driver or board files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

It is ignored by the edma driver since we are just setting back the default
mapping of TC -> Queue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

There is no need to change the default TC -> Queue mapping. By default the
mapping is: TC0 -> Q0, TC1 -> Q1, etc.
Changing this has no benefits at all and all the board files are just setting
the same mapping back to the HW.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Instead of saving the for loop length, take the num_tc value from the pdata.
In case of DT boot set the n_tc to 3 as it is hardwired in edma_of_parse_dt()
This is a temporary state since upcoming patch(es) will change how we are
dealing with these parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

The pdata has been just allocated with devm_kzalloc() in
edma_setup_info_from_dt() and passed to this function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Get the two interrupt line number at the same time by merging the two
instance of if(node){}else{} places.
replace the &pdev->dev with the already existing dev which makes it possible
to collapse lines with devm_request_irq()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

edma param struct is now within an edma_pset struct introduced in Thomas
Gleixner's edma tx status series. Update memcpy function for the same.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The granular residue accounting code uses certain variables specifically
for residue accounting. Document these in the structure declaration.
Also move around some elements and group them together.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The first slot in the ParamRAM of EDMA holds the current active
subtransfer. Depending on the direction we read either the source or
the destination address from there. In the internal psets we have the
address of the buffer(s).

In the cyclic case we only use the internal pset[0] which holds the
start address of the circular buffer and calculate the remaining room
to the end of the buffer.

In the SG case we read the current address and compare it to the
internal psets address and length.

- If the current address is outside of this range, the pset has been
  processed already and we mark it done, update the residue_stat value
  and process the next set. That avoids that we need to walk all
  processed psets for every invocation of tx_status.

- If its inside the range we know that we look at the current active
  set and stop the walk.

- In case of intermediate transfers we update the stats in the
  interrupt callback function before starting the next batch of
  transfers. The tx_status callback and the interrupt callback are
  serialized via vchan.lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[joelf@ti.com: Hunk #2 in original patch manually applied]
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

As Joel pointed out, edma_read_position() uses memcpy_fromio() to read
the parameter ram. That's not synchronized with the internal update as
it does a byte by byte copy. We need to do a 32bit read to get a
consistent value.

Further reading destination and source is pointless. In DEV_TO_MEM
transfers we are only interested in the destination, in MEM_TO_DEV we
care about the source. In MEM_TO_MEM it really does not matter which
one you read.

Simple solution: Remove the pointers, select dest/source via a bool
and return the read value.

Remove the export of this function while at it. The only potential
user is the dmaengine and that's always builtin.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

For granular accounting we need to store the direction and the
information for the individual psets:

- source or destination address, depending on direction
- length
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Preparatory patch to support finer grained accounting.

Move the edma_params array out of edma_desc so we can add further per
pset data to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[joelf@ti.com: Fixed up hunk #3 in original patch to apply]
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

It's likely that the caller investigates the status of a currently
active descriptor. Make that simple check first and only rumage in the
vchan list if that fails.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The residue reporting in edma_tx_status() is just broken. It blindly
walks the psets and recalculates the lenght of the transfer from the
hardware parameters. For cyclic transfers it adds the link pset, which
results in interestingly large residues. For non-cyclic it adds the
dummy pset, which is stupid as well.

Aside of that it's silly to walk through the pset params when the per
descriptor residue is known at the point of creating it.

Store the information in edma_desc and use it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

It helps to identify issues if we have some information regarding to the
channel which the event is associated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The vchan lock in edma_callback is acquired in hard interrupt context. As
interrupts are already disabled, there's no point in save/restoring interrupt
mask bit or cpsr flags.

Get rid of flags local variable and use spin_lock instead of spin_lock_irqsave.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

We add DMA memcpy support to EDMA driver. Successful tests performed using
dmatest kernel module. Copy alignment is set to DMA_SLAVE_BUSWIDTH_4_BYTES and
users must ensure length is aligned so that copy is performed fully.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

In case of not supported direction it is better to print the direction also.
It is unlikely, but in such an event it helps with the debugging.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

prep_slave_sg and prep_dma_cyclic callbacks have mostly same failure cases
with the same texts printed in case we hit them. It helps when debugging if
we know exactly which callback generated the errors.
At the same time change the debug level for descriptor allocation failure
from dbg to err since all other error cases are dev_err and this failure is
similarly fatal as the other ones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

With the callback implemented omap-dma can provide information to client
drivers regarding to supported address widths, directions, residue
granularity, etc.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Do not print the paRAM information when verbose debugging is not asked and
also reduce the number of lines printed in edma_prep_dma_cyclic()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Indicate that the edma dmaengine driver has support for cyclic mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Pause/Resume can be used by the audio stack when the stream is paused/resumed
The edma platform code has support for this and the legacy audio stack used
this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

When clients asks for maxburst = 0 it is basically the same case as if they
were asking for maxburst = 1 since in both case ASYNC need to be used and
the eDMA is expected to write/read one word per DMA request.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

For later use save the number of queues available for the CC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The edmacc_param struct should follow the layout of the paRAM area in the
HW. Be explicit on the size of the fields (u32) and also mark the struct
as packed to avoid any padding on non 32bit architectures.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Pull slave-dmaengine fixes from Vinod Koul:
 "Back from long weekend here in India and now the time to send fixes
  for slave dmaengine.
   - Dan's fix of sirf xlate code
   - Jean's fix for timberland
   - edma fixes by Sekhar for SG handling and Yuan for changing init
     call"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: fix eDMA driver as a subsys_initcall
  dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
  platform: Fix timberdale dependencies
  dma: edma: fix incorrect SG list handling

Pull iommu fixes from Joerg Roedel:
 "Fixes for regressions:

   - fix wrong IOMMU enumeration causing some SCSI device drivers
     initialization failures
   - ARM-SMMU fixes for a panic condition and a wrong return value"

* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
  iommu/arm-smmu: Return 0 on unmap failure
  iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
  iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
  iommu/vt-d: fix memory leakage caused by commit ea8ea460

Pull perf tooling fixes from Ingo Molnar:
 "Three small tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Improve error reporting
  perf tools: Adjust symbols in VDSO
  perf kvm: Fix 'Min time' counting in report command

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent

Pull perf/urgent fixes from Jiri Olsa:

User visible changes:

  * Adjust symbols in VDSO to properly resolve its function names (Vladimir Nikulichev)

  * Improve error reporting for record session failure (Adrien BAK)

  * Fix 'Min time' counting in report command (Alexander Yarygin)
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
  session = perf_session__new(file, false, NULL);

The error message:
"Not enough memory for reading per file header"

is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"

I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.

Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.

Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Adrien BAK <adrien.bak@metascale.org>
Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>

pert-report doesn't resolve function names in VDSO:

$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
            8.76%
               0x7fff6b1fe861
               __gettimeofday
               ACE_OS::gettimeofday()
...

In this case symbol values should be adjusted the same way as for executables,
relocatable objects and prelinked libraries.

After fix:

$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
            8.76%
               __vdso_gettimeofday
               __gettimeofday
               ACE_OS::gettimeofday()
Signed-off-by: Vladimir Nikulichev <nvs@tbricks.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvsSigned-off-by: Jiri Olsa <jolsa@redhat.com>