ODROID-X board have a max77686 PMIC on i2c channel 0. The properties of used
LDO and BUCK are defined according the schematic.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

RTC is a basic feature of EXYNOS5440. But it was disabled
by issue that comes from EXYNOS5250. (commit id: 522ccdb6)
That issue only applies to EXYNOS5250 not EXYNOS5440. So,
there is no issue with enabled RTC on EXYNOS5440. This
change was tested on EXYNOS5440.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds display timing node for a DP panel to Arndale Board DTS file
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds clock provider information for DP controller required by CCF.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add DT node for DP controller to exynos5250 based Arndale Board
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

These nodes have separately been added to 4212 and 4412 dtsi
files by commit 30269ddf ("ARM: exynos: add missing properties
for combiner IRQs"). The existing node also contained a few
incorrect entries.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add max8997 regulator device node for exynos4210-origen board and list
all the supported regulators.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enables TMU on Origen4210 board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds TMU clock entries to exynos4210.dtsi file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added clock entry definitions to MFC bindings document.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added MFC related clock entries in exynos4.dtsi file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added keypad node entries to SMDK4412 board DT file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added keypad node entries to Exynos4412 based Origen board DT file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Keypad pins/lines are board specific and should be added to respective
board dts files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adding DWC3 device tree node for Exynos5250 needed to
parse device tree data.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Document device tree binding information as required by the
Samsung' USB 3.0 controller.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adding usb3.0 phy node for Exynos5250 along with the
necessary device data to be parsed.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch fixes warnings due to missing lock on write error path.

  WARNING: at fs/hpfs/hpfs_fn.h:353 hpfs_truncate+0x75/0x80 [hpfs]()
  Hardware name: empty
  Pid: 26563, comm: dd Tainted: P           O 3.9.4 #12
  Call Trace:
    hpfs_truncate+0x75/0x80 [hpfs]
    hpfs_write_begin+0x84/0x90 [hpfs]
    _hpfs_bmap+0x10/0x10 [hpfs]
    generic_file_buffered_write+0x121/0x2c0
    __generic_file_aio_write+0x1c7/0x3f0
    generic_file_aio_write+0x7c/0x100
    do_sync_write+0x98/0xd0
    hpfs_file_write+0xd/0x50 [hpfs]
    vfs_write+0xa2/0x160
    sys_write+0x51/0xa0
    page_fault+0x22/0x30
    system_call_fastpath+0x1a/0x1f
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org  # 2.6.39+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:

 - Trivial: unused variable removal

 - Posix-timers: Add the clock ID to the new proc interface to make it
   useful.  The interface is new and should be functional when we reach
   the final 3.10 release.

 - Cure a false positive warning in the tick code introduced by the
   overhaul in 3.10

 - Fix for a persistent clock detection regression introduced in this
   cycle

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Correct run-time detection of persistent_clock.
  ntp: Remove unused variable flags in __hardpps
  posix-timers: Show clock ID in proc file
  tick: Cure broadcast false positive pending bit warning

Pull irqdomain bug fixes from Grant Likely:
 "This branch contains a set of straight forward bug fixes to the
  irqdomain code and to a couple of drivers that make use of it."

* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
  irqchip: Return -EPERM for reserved IRQs
  irqdomain: document the simple domain first_irq
  kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
  irqdomain: export irq_domain_add_simple

The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: Grant Likely <grant.likely@linaro.org>

The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:

ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another batch of fixes for arm-soc platforms.

  Nothing controversial here, a handful of fixes for regressions and/or
  serious problems across several of the platforms.  Things are slowing
  down nicely on fix rates for 3.10"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
  ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
  ARM: mxs: icoll: Fix interrupts gpio bank 0
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: bcm2835: override the HW UART periphid
  ARM: mvebu: Fix bug in coherency fabric low level init function
  ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
  ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
  ARM: ux500: Only configure wake-up reasons on ux500 based platforms
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels

Pull MIPS fixes from Ralf Baechle:
 "MIPS fixes across the field.  The only area that's standing out is the
  exception handling which received it's dose of breakage as part of the
  microMIPS patchset"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: add missing SZ_1M multiplier
  MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.
  MIPS: OCTEON: Improve _machine_halt implementation.
  MIPS: rtlx: Fix implicit declaration of function set_vi_handler()
  MIPS: Trap exception handling fixes
  MIPS: Quit exposing Kconfig symbols in uapi headers.
  MIPS: Remove duplicate definition of check_for_high_segbits.

Pull m68knommu fix from Greg Ungerer:
 "A single fix for compilation breakage to many of the ColdFire CPU
  targets"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: only use local gpio_request_one if not using GPIOLIB

Pull drm fixes from Dave Airlie:
 "Regression fixers for the big 3:

   - nouveau: hdmi audio, dac load detect, s/r regressions fixed
   - radeon: long standing system hang fixed, hdmi audio and rs780 fast
     fb fixes
   - intel: one old regression, a WARN removal, and a stop X dying fix

  Otherwise one mgag200 fix, a couple of arm build fixes, and a core use
  after free fix."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nv50/kms: use dac loadval from vbios, where it's available
  drm/nv50/disp: force dac power state during load detect
  drm/nv50-nv84/fifo: fix resume regression introduced by playlist race fix
  drm/nv84/disp: Fix HDMI audio regression
  drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC.
  drm/radeon: don't allow audio on DCE6
  drm/radeon: Use direct mapping for fast fb access on RS780/RS880 (v2)
  radeon: Fix system hang issue when using KMS with older cards
  drm/i915: no lvds quirk for hp t5740
  drm/i915: Quirk the pipe A quirk in the modeset state checker
  drm/i915: Fix spurious -EIO/SIGBUS on wedged gpus
  drm/mgag200: Add missing write to index before accessing data register
  drm/nouveau: use mdelay instead of large udelay constants
  drm/tilcd: select BACKLIGHT_LCD_SUPPORT
  drm: fix a use-after-free when GPU acceleration disabled

Pull slave-dmaengine fixes from Vinod Koul:
 "Fix from Andy is for dmatest regression reported by Will and Rabin has
  fixed runtime ref counting for st_dma40"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmatest: do not allow to interrupt ongoing tests
  dmaengine: ste_dma40: fix pm runtime ref counting

Merge tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "This contains 4 fixes.

  The first two fix the case where full RCU debugging is enabled,
  enabling function tracing causes a live lock of the system.  This is
  due to the added debug checks in rcu_dereference_raw() that is used by
  the function tracer.  These checks are also traced by the function
  tracer as well as cause enough overhead to the function tracer to slow
  down the system enough that the time to finish an interrupt can take
  longer than when the next interrupt is triggered, causing a live lock
  from the timer interrupt.

  Talking this over with Paul McKenney, we came up with a fix that adds
  a new rcu_dereference_raw_notrace() that does not perform these added
  checks, and let the function tracer use that.

  The third commit fixes a failed compile when branch tracing is
  enabled, due to the conversion of the trace_test_buffer() selftest
  that the branch trace wasn't converted for.

  The forth patch fixes a bug caught by the RCU lockdep code where a
  rcu_read_lock() is performed when rcu is disabled (either going to or
  from idle, or user space).  This happened on the irqsoff tracer as it
  calls task_uid().  The fix here was to use current_uid() when possible
  that doesn't use rcu locking.  Which luckily, is always used when
  irqsoff calls this code."

* tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Use current_uid() for critical time tracing
  tracing: Fix bad parameter passed in branch selftest
  ftrace: Use the rcu _notrace variants for rcu_dereference_raw() and friends
  rcu: Add _notrace variation of rcu_dereference_raw() and hlist_for_each_entry_rcu()

Commit 9f29ab11 ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600.  Tony says:

  "It panics with the message:

   Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel

   [...] my problem comes from arch/ia64/hp/common/sba_iommu.c
   where the code in sba_init() says:

        acpi_bus_register_driver(&acpi_sba_ioc_driver);
        if (!ioc_list) {

   but because of this change we never managed to call ioc_init()
   so ioc_list doesn't get set up, and we die."

Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From Shawn Guo, mxs fixes for 3.10:

- Since the time we move to MULTI_IRQ_HANDLER, the 0x7f polling for no
  interrupt in icoll_handle_irq() becomes insane, because 0x7f is an
  valid interrupt number, the irq of gpio bank 0.  That unnecessary
  polling results in the driver not detecting when irq 0x7f is active
  which makes the machine effectively dead lock.  The fix removes the
  interrupt poll loop and allows usage of gpio0 interrupt without an
  infinite loop.

* tag 'mxs-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: icoll: Fix interrupts gpio bank 0
Signed-off-by: Olof Johansson <olof@lixom.net>

From Shawn Guo, imx fixes for 3.10, take 2:

- One device tree fix for all spi node to have per clock added.
  The clock is needed by spi driver to calculate bit rate divisor.
  The spi node in the current device trees either does not have the
  clock or is defined as dummy clock, in which case the driver probe
  will fail or spi will run at a wrong bit rate.

- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.

* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: Olof Johansson <olof@lixom.net>

If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled.  Avoid this hang by calling
debug_ll_io_init() early.

Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io().  After this patch the hang goes away.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman, Renesas ARM based SoC fixes for v3.10:
- Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
  This avoids conflicts when the USB_OVCn pins are used by another function.
  This has been observed to be a problem in v3.10-rc1.
- Update CMT clock rating for sh73a0 SoC to resolve boot failure
  on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.

* tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
Signed-off-by: Olof Johansson <olof@lixom.net>

Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.

Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.

With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull infiniband fixes from Roland Dreier:
 - qib RCU/lockdep fix
 - iser device removal fix, plus doc fixes

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/qib: Fix lockdep splat in qib_alloc_lkey()
  MAINTAINERS: Add entry for iSCSI Extensions for RDMA (iSER) initiator
  IB/iser: Add Mellanox copyright
  IB/iser: Fix device removal flow

Pull vfio fix from Alex Williamson:
 "fix rmmod crash"

* tag 'vfio-v3.10-rc5' of git://github.com/awilliam/linux-vfio:
  vfio: fix crash on rmmod

Merge tag 'ecryptfs-3.10-rc5-msync' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes how eCryptfs handles msync to sync both the upper and lower
   file
 - A couple of MAINTAINERS updates

* tag 'ecryptfs-3.10-rc5-msync' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Check return of filemap_write_and_wait during fsync
  Update eCryptFS maintainers
  ecryptfs: fixed msync to flush data