It may be desirable in some systems to have
insight into the driver via debugfs, but not
affect its operation via the debug logging
code that is inserted everywhere when DEBUG
is configured.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Some comments in iwl-dev.h still refer to 4965 but used by all the _agn
devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Move configuration structure for _agn devices from iwl-dev.h to
iwl-agn.h. Those data structures are for _agn devices and should be keep
for _agn devices only.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This patch enables all remaining 6000 series Gen2 devices.
To work-around a firmware crash problem, we disable sending
bt coex command for 6000g2b series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

In order to debug problems before the ALIVE
notification is received, new firmware files
contain the event/error log information in
the file. Use that information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

There are a few places where sta_lock is used, but the
station information protected by it is accessed outside
of the lock. Address this in two ways, if the access
won't sleep then just move the access into the lock, if
the access can sleep then copy the needed station
information to the stack to be accessed without risk of
it changing while access in progress.

Additionally, a number of other places access station
station information without holding the sta_lock, fix
those as well.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This constant is not used, and incorrect, since
the broadcast ID must be used for multicast too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The stations debugfs entry doesn't even show
the stations' MAC addresses Also, the TID
information is formatted very oddly, and
misses the important tfds_in_queue variable.
Fix this to make the file more useful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This function is only used by the agn drivers,
so doesn't have to be in core and exported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Unlike agn, where the sequence numbers must
match with the TFD index, the driver for 3945
devices can use the sequence numbers provided
by mac80211 for QoS frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

If a firmware file misses one of the required
instruction or data pieces, the driver currently
crashes. Let it gracefully refuse that firmware
file instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Since agn and 3945 have different statistics_notif data structure, each
should has its own statistics_flag function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

agn and 3945 has different statistics_notif data structure; since 3945
has it statistics_notif data structure inside the _3945 portion of
iwl_priv, it make sense to move the agn statistics_notif into _agn portion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

There are now five places where we need to
look up the station ID, but the sta pointer
may be NULL due to mac80211 passing that to
indicate a certain special state.

Replace all these by a new inline function,
called iwl_sta_id_or_broadcast(), and add
documentation about when to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Preparation for futher cleanups in the area of properly maintaining the skb
data without fiddling with the skb->data pointer.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows for specific identification of beacons in the debugfs
frame stream.
Preparation for later differences between dumped TX frames and dumped
beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The handling of tx descriptors for beacons can be simplified by updating
write_tx_desc implementations of each driver to write directly to the
queue entry descriptor instead of to a provided memory area.
This is also a preparation for further clean ups where descriptors are
properly reserved in the skb instead of fiddling with the skb data
pointer.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Where possible, write the tx descriptor words from start to end, to
follow a logical ordering of words.
Where this is not possible (in rt2400pci, rt2500pci and rt61pci) add
a comment as to why word 0 needs to be written last.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The buffer address descriptor word is not part of the TXINFO structure
needed for beacons. The current writing of that word for beacons is
therefore an out-of-bounds write.
Fix this by only writing the buffer address descriptor word for TX
queues.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The skb frame descriptor is called everywhere skbdesc, except in one
place in rt2x00debug_dump_frame. Change that occurence to have
consistent naming.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* add support for the Qwest/Actiontec 802AIN Wireless N USB Network Adapter.

lsusb identifies the device as: "ID 1668:1200 Actiontec Electronics, Inc. [hex]"

usb_modeswitch package and appropriate rules are required to switch
the device from "ID 0ace:20ff ZyDas"

Changes-licensed-under: GPL
Signed-off-by: Steve Tanner <steve.tanner@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drop cast on the result of kmalloc and similar functions.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
type T;
@@

- (T *)
  (\(kmalloc\|kzalloc\|kcalloc\|kmem_cache_alloc\|kmem_cache_zalloc\|
   kmem_cache_alloc_node\|kmalloc_node\|kzalloc_node\)(...))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Paged RX skb patch broke the defragmentation. We need to read hdr again
after linearization.

It fixes following bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2194Signed-off-by: Zhu, Yi <yi.zhu@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the double swapping of the descriptor data structure, instead
keep it little-endian (native format of the eeprom data), and byteswap
on access.
This allows sparse to verify endian access to the eeprom struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use ENDPOINT_MAX instead of HST_ENDPOINT_MAX.
This fixes a stack corruption issue.

This is based on a patch sent by Dan Carpenter <error27@gmail.com>.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ready message from the target could be processed
before the host HW init has completed. In this case,
htc_process_target_rdy() would assume the target has timed
out, when it hasn't. Fix this by checking if the target
has sent the ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The HTC state has to be setup before initializing
the target because the ready message could possibly
come before the control endpoints in HTC have been
identified.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The URBs have to be allocated before uploading
the firmware to the target. This is needed to process
the target ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since ->sta_notify() can sleep, protect
the callback with a mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check the mode in channel switch ie for either 0 or 1 on transmission.
A channel switch mode set to 1 means that the STA in a BSS to which the
frame containing the element is addressed shall transmit no further
frames 	within the BSS until the scheduled channel switch.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds support for offloading the channel switch
operation to devices that support such, typically
by having specific firmware API for it. The reasons
for this could be that the firmware provides better
timing or that regulatory enforcement done by the
device requires special handling of CSAs.

In order to allow drivers to specify the timing to
the device, the new channel_switch callback will
pass through the received frame's mactime, where
available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't send them for further processing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These changes include:

  * For PAPRD, the TXRF3.capdiv5G, TXRF3.rdiv5G and TXRF3.rdiv2G
    are set to 0x0, the TXRF6.capdiv2G is set to 0x2 for all
    three chains.
  * The d2cas5G/d3cas5G/d4cas5G was updated to 4/4/4 in lowest_ob_db
    Tx gain table.
  * To improve DPPM, three parameters were updated (Released from Madhan):
	1. RANGE_OSDAC is set to 0x1 for 2G, 0x0 for 5G
	2. offsetC1 is set to 0xc
	3. inv_clk320_adc is set to 0x1
  * To reduce PHY error(from spur), cycpwr_thr1 and cycpwr_thr1_ext
    are increased to 0x8 at 2G.
  * The 2G Rx gain tables are updated with mixer gain setting 3,1,0.

The new checksums yield:

initvals -f ar9003
0x00000000c2bfa7d5        ar9300_2p0_radio_postamble
0x00000000ada2b114        ar9300Modes_lowest_ob_db_tx_gain_table_2p0
0x00000000e0bc2c84        ar9300Modes_fast_clock_2p0
0x00000000056eaf74        ar9300_2p0_radio_core
0x0000000000000000        ar9300Common_rx_gain_table_merlin_2p0
0x0000000078658fb5        ar9300_2p0_mac_postamble
0x0000000023235333        ar9300_2p0_soc_postamble
0x0000000054d41904        ar9200_merlin_2p0_radio_core
0x00000000748572cf        ar9300_2p0_baseband_postamble
0x000000009aa5a0a4        ar9300_2p0_baseband_core
0x000000003df9a326        ar9300Modes_high_power_tx_gain_table_2p0
0x000000001cfba124        ar9300Modes_high_ob_db_tx_gain_table_2p0
0x0000000011302700        ar9300Common_rx_gain_table_2p0
0x00000000e3eab114        ar9300Modes_low_ob_db_tx_gain_table_2p0
0x00000000c9d66d40        ar9300_2p0_mac_core
0x000000001e1d0800        ar9300Common_wo_xlna_rx_gain_table_2p0
0x00000000a0c54980        ar9300_2p0_soc_preamble
0x00000000292e2544        ar9300PciePhy_pll_on_clkreq_disable_L1_2p0
0x000000002d3e2544        ar9300PciePhy_clkreq_enable_L1_2p0
0x00000000293e2544        ar9300PciePhy_clkreq_disable_L1_2p0

Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.

Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.

This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The goto and the break are equivelent.  I removed the goto in memory of
Edsger Dijkstra who famously hated gotos and who would have been eighty
years old next Tuesday.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The "(wl == NULL)" test doesn't work here because "wl" is always
non-null.  The intent of the code is to return if the interface
was not supported by the driver.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>