[ Upstream commit 22904bdf ]

The Invensense ICM-20602 is a 6-axis MotionTracking device that
combines a 3-axis gyroscope and an 3-axis accelerometer. It is very
similar to the ICM-20608 imu which is already supported by the mpu6050
driver. The main difference is that the ICM-20602 has the i2c bus
disable bit in a separate register.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b0814361 ]

blkcg_print_stat() iterates blkgs under RCU and doesn't test whether
the blkg is online.  This can call into pd_stat_fn() on a pd which is
still being initialized leading to an oops.

The heaviest operation - recursively summing up rwstat counters - is
already done while holding the queue_lock.  Expand queue_lock to cover
the other operations and skip the blkg if it isn't online yet.  The
online state is protected by both blkcg and queue locks, so this
guarantees that only online blkgs are processed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Roman Gushchin <guro@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Fixes: 903d23f0 ("blk-cgroup: allow controllers to output their own stats")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 63bdef6c ]

Commit 03c4749d ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.

This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.

This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:

[    0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ

This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.

This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.

Cc: stable@vger.kernel.org
Fixes: 03c4749d ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e74540b2 ]

When the extent tree is modified, it should be protected by inode
cluster lock and ip_alloc_sem.

The extent tree is accessed and modified in the
ocfs2_prepare_inode_for_write, but isn't protected by ip_alloc_sem.

The following is a case.  The function ocfs2_fiemap is accessing the
extent tree, which is modified at the same time.

  kernel BUG at fs/ocfs2/extent_map.c:475!
  invalid opcode: 0000 [#1] SMP
  Modules linked in: tun ocfs2 ocfs2_nodemanager configfs ocfs2_stackglue [...]
  CPU: 16 PID: 14047 Comm: o2info Not tainted 4.1.12-124.23.1.el6uek.x86_64 #2
  Hardware name: Oracle Corporation ORACLE SERVER X7-2L/ASM, MB MECH, X7-2L, BIOS 42040600 10/19/2018
  task: ffff88019487e200 ti: ffff88003daa4000 task.ti: ffff88003daa4000
  RIP: ocfs2_get_clusters_nocache.isra.11+0x390/0x550 [ocfs2]
  Call Trace:
    ocfs2_fiemap+0x1e3/0x430 [ocfs2]
    do_vfs_ioctl+0x155/0x510
    SyS_ioctl+0x81/0xa0
    system_call_fastpath+0x18/0xd8
  Code: 18 48 c7 c6 60 7f 65 a0 31 c0 bb e2 ff ff ff 48 8b 4a 40 48 8b 7a 28 48 c7 c2 78 2d 66 a0 e8 38 4f 05 00 e9 28 fe ff ff 0f 1f 00 <0f> 0b 66 0f 1f 44 00 00 bb 86 ff ff ff e9 13 fe ff ff 66 0f 1f
  RIP  ocfs2_get_clusters_nocache.isra.11+0x390/0x550 [ocfs2]
  ---[ end trace c8aa0c8180e869dc ]---
  Kernel panic - not syncing: Fatal exception
  Kernel Offset: disabled

This issue can be reproduced every week in a production environment.

This issue is related to the usage mode.  If others use ocfs2 in this
mode, the kernel will panic frequently.

[akpm@linux-foundation.org: coding style fixes]
[Fix new warning due to unused function by removing said function - Linus ]
Link: http://lkml.kernel.org/r/1568772175-2906-2-git-send-email-sunny.s.zhang@oracle.comSigned-off-by: Shuning Zhang <sunny.s.zhang@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 29c2c6aa ]

When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.

However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.

Fixes: 7981c001 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8472ba62 ]

In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if
e1000_up() fails, leading to memory leaks. Refactor the code to fix this
issue.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8d5cfd7f ]

At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.

If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.

The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4202e219 ]

The remove misses to disable and unprepare priv->macclk like what is done
when probe fails.
Add the missed call in remove.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit be3df3dd ]

If the delegation is marked as being revoked, we must not use it
for cached opens.

Fixes: 869f9dfa ("NFSv4: Fix races between nfs_remove_bad_delegation() and delegation return")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d8eca64e ]

When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.

Fixes: fec9095b "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 719b85c3 ]

If rndis_filter_open() fails, we need to remove the rndis device created
in earlier steps, before returning an error code. Otherwise, the retry of
netvsc_attach() from its callers will fail and hang.

Fixes: 7b2ee50c ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bc2fde42 ]

[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D

[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 57c0f58e ]

Use ERR_PTR to return back the error happened during amdgpu_ib_schedule.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ad3e8da2 ]

Acer Aspire A315-41 requires the very same workaround as the existing
quirk for Dell Latitude 5495.  Add the new entry for that.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1137799Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b9cd75e6 ]

The switch driver keeps a "vid" variable per port, which signifies _the_
VLAN ID that is stripped on that port's egress (aka the native VLAN on a
trunk port).

That is the way the hardware is designed (mostly). The port->vid is
programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told
to send all traffic as tagged except the one having port->vid.

There exists a possibility of finer-grained egress untagging decisions:
using the VCAP IS1 engine, one rule can be added to match every
VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as
action. However, the IS1 can hold at most 512 entries, and the VLANs are
in the order of 6 * 4096.

So the code is fine for now. But this sequence of commands:

$ bridge vlan add dev swp0 vid 1 pvid untagged
$ bridge vlan add dev swp0 vid 2 untagged

makes untagged and pvid-tagged traffic be sent out of swp0 as tagged
with VID 1, despite user's request.

Prevent that from happening. The user should temporarily remove the
existing untagged VLAN (1 in this case), add it back as tagged, and then
add the new untagged VLAN (2 in this case).

Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1c44ce56 ]

Background information: the driver operates the hardware in a mode where
a single VLAN can be transmitted as untagged on a particular egress
port. That is the "native VLAN on trunk port" use case. Its value is
held in port->vid.

Consider the following command sequence (no network manager, all
interfaces are down, debugging prints added by me):

$ ip link add dev br0 type bridge vlan_filtering 1
$ ip link set dev swp0 master br0

Kernel code path during last command:

br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER):
[   21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0

br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING):
[   21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0

br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add
[   21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1

So far so good. The bridge has replaced the driver's default pvid used
in standalone mode (0) with its own default_pvid (1). The port's vid
(native VLAN) has also changed from 0 to 1.

$ ip link set dev swp0 up

[   31.722956] 8021q: adding VLAN 0 to HW filter on device swp0
do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add:
[   31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0

The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make
ports be able to transmit and receive 802.1p-tagged traffic by default.
This API is supposed to offload a VLAN sub-interface, which for a switch
port means to add a VLAN that is not a pvid, and tagged on egress.

But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds
back vid 0 as "egress untagged". Now back to the initial paragraph:
there is a single untagged VID that the driver keeps track of, and that
has just changed from 1 (the pvid) to 0. So this breaks the bridge
core's expectation, because it has changed vid 1 from untagged to
tagged, when what the user sees is.

$ bridge vlan
port    vlan ids
swp0     1 PVID Egress Untagged

br0      1 PVID Egress Untagged

But curiously, instead of manifesting itself as "untagged and
pvid-tagged traffic gets sent as tagged on egress", the bug:

- is hidden when vlan_filtering=0
- manifests as dropped traffic when vlan_filtering=1, due to this setting:

	if (port->vlan_aware && !port->vid)
		/* If port is vlan-aware and tagged, drop untagged and priority
		 * tagged frames.
		 */
		val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA |
		       ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA |
		       ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA;

which would have made sense if it weren't for this bug. The setting's
intention was "this is a trunk port with no native VLAN, so don't accept
untagged traffic". So the driver was never expecting to set VLAN 0 as
the value of the native VLAN, 0 was just encoding for "invalid".

So the fix is to not send 802.1p traffic as untagged, because that would
change the port's native vlan to 0, unbeknownst to the bridge, and
trigger unexpected code paths in the driver.

Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 63a41746 ]

When rmmod hip04_eth.ko, we can get the following warning:

Task track: rmmod(1623)>bash(1591)>login(1581)>init(1)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac()
Trying to free already-free IRQ 200
Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv
CPU: 0 PID: 1623 Comm: rmmod Tainted: G           O    4.4.193 #1
Hardware name: Hisilicon A15
[<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14)
[<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8)
[<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0)
[<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68)
[<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac)
[<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c)
[<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec)
[<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104)
[<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8)
[<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c)
[<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0)
[<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10)
---[ end trace bb25d6123d849b44 ]---

Currently "rmmod hip04_eth.ko" call free_irq more than once
as devres_release_all and hip04_remove both call free_irq.
This results in a 'Trying to free already-free IRQ' warning.
To solve the problem free_irq has been moved out of hip04_remove.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 85ac30fa ]

In the highly unlikely event that we fail to allocate either of the
"/txrx" or "/control" workqueues, we should bail cleanly rather than
blindly march on with NULL queue pointer(s) installed in the
'fjes_adapter' instance.

Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Nicolas Waisman <nico@semmle.com>
Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit af8fd042 ]

The following scenario results in an IO hang:
1) ctrl completes a request with NVME_SC_ANA_TRANSITION.
   NVME_NS_ANA_PENDING bit in ns->flags is set and ana_work is triggered.
2) ana_work: nvme_read_ana_log() tries to get the ANA log page from the ctrl.
   This fails because ctrl disconnects.
   Therefore nvme_update_ns_ana_state() is not called
   and NVME_NS_ANA_PENDING bit in ns->flags is not cleared.
3) ctrl reconnects: nvme_mpath_init(ctrl,...) calls
   nvme_read_ana_log(ctrl, groups_only=true).
   However, nvme_update_ana_state() does not update namespaces
   because nr_nsids = 0 (due to groups_only mode).
4) scan_work calls nvme_validate_ns() finds the ns and re-validates OK.

Result:
The ctrl is now live but NVME_NS_ANA_PENDING bit in ns->flags is still set.
Consequently ctrl will never be considered a viable path by __nvme_find_path().
IO will hang if ctrl is the only or the last path to the namespace.

More generally, while ctrl is reconnecting, its ANA state may change.
And because nvme_mpath_init() requests ANA log in groups_only mode,
these changes are not propagated to the existing ctrl namespaces.
This may result in a mal-function or an IO hang.

Solution:
nvme_mpath_init() will nvme_read_ana_log() with groups_only set to false.
This will not harm the new ctrl case (no namespaces present),
and will make sure the ANA state of namespaces gets updated after reconnect.

Note: Another option would be for nvme_mpath_init() to invoke
nvme_parse_ana_log(..., nvme_set_ns_ana_state) for each existing namespace.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d3566abb ]

In shutdown/reboot paths, the timer is not stopped:

  qla2x00_shutdown
  pci_device_shutdown
  device_shutdown
  kernel_restart_prepare
  kernel_restart
  sys_reboot

This causes lockups (on powerpc) when firmware config space access calls
are interrupted by smp_send_stop later in reboot.

Fixes: e30d1756 ("[SCSI] qla2xxx: Addition of shutdown callback handler.")
Link: https://lore.kernel.org/r/20191024063804.14538-1-npiggin@gmail.comSigned-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b681a052 ]

eq->buf_list->buf and eq->buf_list should also be freed when eqe_hop_num
is set to 0, or there will be memory leaks.

Fixes: a5073d60 ("RDMA/hns: Add eq support of hip08")
Link: https://lore.kernel.org/r/1572072995-11277-3-git-send-email-liweihang@hisilicon.comSigned-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d4934f45 ]

_put_ep_safe() and _put_pass_ep_safe() free the skb before it is freed by
process_work(). fix double free by freeing the skb only in process_work().

Fixes: 1dad0ebe ("iw_cxgb4: Avoid touch after free error in ARP failure handlers")
Link: https://lore.kernel.org/r/1572006880-5800-1-git-send-email-bharat@chelsio.comSigned-off-by: Dakshaja Uppalapati <dakshaja@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 28df0642 ]

This isn't really accurate right. fread() doesn't always
return 0 in error. It could return < number of elements
and set errno.
Signed-off-by: GwanYeong Kim <gy741.kim@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191018032223.4644-1-gy741.kim@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 88f6bf38 ]

A recent info-leak bug manifested itself along with warning about a
negative buffer overflow:

	ldusb 1-1:0.28: Read buffer overflow, -131383859965943 bytes dropped

when it was really a rather large positive one.

A sanity check that prevents this has now been put in place, but let's
fix up the size format specifiers, which should all be unsigned.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-3-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d482c7bb ]

Endpoints with a maxpacket length of 0 are probably useless.  They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.

Currently the USB core does not check for endpoints having a maxpacket
value of 0.  This patch adds a check, printing a warning and skipping
over any endpoints it catches.

Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>

Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 75be6f70 ]

The events in the same group don't start or stop simultaneously.
Here is the ftrace when enabling event group for uncore_iio_0:

  # perf stat -e "{uncore_iio_0/event=0x1/,uncore_iio_0/event=0xe/}"

            <idle>-0     [000] d.h.  8959.064832: read_msr: a41, value
  b2b0b030		//Read counter reg of IIO unit0 counter0
            <idle>-0     [000] d.h.  8959.064835: write_msr: a48, value
  400001			//Write Ctrl reg of IIO unit0 counter0 to enable
  counter0. <------ Although counter0 is enabled, Unit Ctrl is still
  freezed. Nothing will count. We are still good here.
            <idle>-0     [000] d.h.  8959.064836: read_msr: a40, value
  30100                   //Read Unit Ctrl reg of IIO unit0
            <idle>-0     [000] d.h.  8959.064838: write_msr: a40, value
  30000			//Write Unit Ctrl reg of IIO unit0 to enable all
  counters in the unit by clear Freeze bit  <------Unit0 is un-freezed.
  Counter0 has been enabled. Now it starts counting. But counter1 has not
  been enabled yet. The issue starts here.
            <idle>-0     [000] d.h.  8959.064846: read_msr: a42, value 0
			//Read counter reg of IIO unit0 counter1
            <idle>-0     [000] d.h.  8959.064847: write_msr: a49, value
  40000e			//Write Ctrl reg of IIO unit0 counter1 to enable
  counter1.   <------ Now, counter1 just starts to count. Counter0 has
  been running for a while.

Current code un-freezes the Unit Ctrl right after the first counter is
enabled. The subsequent group events always loses some counter values.

Implement pmu_enable and pmu_disable support for uncore, which can help
to batch hardware accesses.

No one uses uncore_enable_box and uncore_disable_box. Remove them.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-drivers-review@eclists.intel.com
Cc: linux-perf@eclists.intel.com
Fixes: 087bfbb0 ("perf/x86: Add generic Intel uncore PMU support")
Link: https://lkml.kernel.org/r/1572014593-31591-1-git-send-email-kan.liang@linux.intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e431e79b ]

This saves us writing the IBS control MSR twice when disabling the
event.

I searched revision guides for all families since 10h, and did not
find occurrence of erratum #420, nor anything remotely similar:
so we isolate the secondary MSR write to family 10h only.

Also unconditionally update the count mask for IBS Op implementations
that have read & writeable current count (CurCnt) fields in addition
to the MaxCnt field.  These bits were reserved on prior
implementations, and therefore shouldn't have negative impact.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: c9574fe0 ("perf/x86-ibs: Implement workaround for IBS erratum #420")
Link: https://lkml.kernel.org/r/20191023150955.30292-2-kim.phillips@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 317b96bb ]

The loop that reads all the IBS MSRs into *buf stopped one MSR short of
reading the IbsOpData register, which contains the RipInvalid status bit.

Fix the offset_max assignment so the MSR gets read, so the RIP invalid
evaluation is based on what the IBS h/w output, instead of what was
left in memory.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: d47e8238 ("perf/x86-ibs: Take instruction pointer from ibs sample")
Link: https://lkml.kernel.org/r/20191023150955.30292-1-kim.phillips@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a7d9874c ]

layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1a1c851b ]

We meet several NULL pointer issues if configfs_composite_unbind
and composite_setup (or composite_disconnect) are running together.
These issues occur when do the function switch stress test, the
configfs_compsoite_unbind is called from user mode by
echo "" to /sys/../UDC entry, and meanwhile, the setup interrupt
or disconnect interrupt occurs by hardware. The composite_setup
will get the cdev from get_gadget_data, but configfs_composite_unbind
will set gadget data as NULL, so the NULL pointer issue occurs.
This concurrent is hard to reproduce by native kernel, but can be
reproduced by android kernel.

In this commit, we introduce one spinlock belongs to structure
gadget_info since we can't use the same spinlock in usb_composite_dev
due to exclusive running together between composite_setup and
configfs_composite_unbind. And one bit flag 'unbind' to indicate the
code is at unbind routine, this bit is needed due to we release the
lock at during configfs_composite_unbind sometimes, and composite_setup
may be run at that time.

Several oops:

oops 1:
android_work: sent uevent USB_STATE=CONNECTED
configfs-gadget gadget: super-speed config #1: b
android_work: sent uevent USB_STATE=CONFIGURED
init: Received control message 'start' for 'adbd' from pid: 3515 (system_server)
Unable to handle kernel NULL pointer dereference at virtual address 0000002a
init: Received control message 'stop' for 'adbd' from pid: 3375 (/vendor/bin/hw/android.hardware.usb@1.1-servic)
Mem abort info:
  Exception class = DABT (current EL), IL = 32 bits
  SET = 0, FnV = 0
  EA = 0, S1PTW = 0
Data abort info:
  ISV = 0, ISS = 0x00000004
  CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgd = ffff8008f1b7f000
[000000000000002a] *pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 4 PID: 2457 Comm: irq/125-5b11000 Not tainted 4.14.98-07846-g0b40a9b-dirty #16
Hardware name: Freescale i.MX8QM MEK (DT)
task: ffff8008f2a98000 task.stack: ffff00000b7b8000
PC is at composite_setup+0x44/0x1508
LR is at android_setup+0xb8/0x13c
pc : [<ffff0000089ffb3c>] lr : [<ffff000008a032fc>] pstate: 800001c5
sp : ffff00000b7bbb80
x29: ffff00000b7bbb80 x28: ffff8008f2a3c010
x27: 0000000000000001 x26: 0000000000000000                                                          [1232/1897]
audit: audit_lost=25791 audit_rate_limit=5 audit_backlog_limit=64
x25: 00000000ffffffa1 x24: ffff8008f2a3c010
audit: rate limit exceeded
x23: 0000000000000409 x22: ffff000009c8e000
x21: ffff8008f7a8b428 x20: ffff00000afae000
x19: ffff0000089ff000 x18: 0000000000000000
x17: 0000000000000000 x16: ffff0000082b7c9c
x15: 0000000000000000 x14: f1866f5b952aca46
x13: e35502e30d44349c x12: 0000000000000008
x11: 0000000000000008 x10: 0000000000000a30
x9 : ffff00000b7bbd00 x8 : ffff8008f2a98a90
x7 : ffff8008f27a9c90 x6 : 0000000000000001
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 0000000000000000 x2 : 0000000000000006
x1 : ffff0000089ff8d0 x0 : 732a010310b9ed00

X7: 0xffff8008f27a9c10:
9c10  00000002 00000000 00000001 00000000 13110000 ffff0000 00000002 00208040
9c30  00000000 00000000 00000000 00000000 00000000 00000005 00000029 00000000
9c50  00051778 00000001 f27a8e00 ffff8008 00000005 00000000 00000078 00000078
9c70  00000078 00000000 09031d48 ffff0000 00100000 00000000 00400000 00000000
9c90  00000001 00000000 00000000 00000000 00000000 00000000 ffefb1a0 ffff8008
9cb0  f27a9ca8 ffff8008 00000000 00000000 b9d88037 00000173 1618a3eb 00000001
9cd0  870a792a 0000002e 16188fe6 00000001 0000242b 00000000 00000000 00000000
using random self ethernet address
9cf0  019a4646 00000000 000547f3 00000000 ecfd6c33 00000002 00000000
using random host ethernet address
 00000000

X8: 0xffff8008f2a98a10:
8a10  00000000 00000000 f7788d00 ffff8008 00000001 00000000 00000000 00000000
8a30  eb218000 ffff8008 f2a98000 ffff8008 f2a98000 ffff8008 09885000 ffff0000
8a50  f34df480 ffff8008 00000000 00000000 f2a98648 ffff8008 09c8e000 ffff0000
8a70  fff2c800 ffff8008 09031d48 ffff0000 0b7bbd00 ffff0000 0b7bbd00 ffff0000
8a90  080861bc ffff0000 00000000 00000000 00000000 00000000 00000000 00000000
8ab0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8ad0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8af0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000

X21: 0xffff8008f7a8b3a8:
b3a8  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b3c8  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b3e8  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b408  00000000 00000000 00000000 00000000 00000000 00000000 00000001 00000000
b428  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b448  0053004d 00540046 00300031 00010030 eb07b520 ffff8008 20011201 00000003
b468  e418d109 0104404e 00010302 00000000 eb07b558 ffff8008 eb07b558 ffff8008
b488  f7a8b488 ffff8008 f7a8b488 ffff8008 f7a8b300 ffff8008 00000000 00000000

X24: 0xffff8008f2a3bf90:
bf90  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfb0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfd0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bff0  00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
c010  00000000 00000000 f2a3c018 ffff8008 f2a3c018 ffff8008 08a067dc ffff0000
c030  f2a5a000 ffff8008 091c3650 ffff0000 f716fd18 ffff8008 f716fe30 ffff8008
c050  f2ce4a30 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
c070  f76c8010 ffff8008 f2ce4b00 ffff8008 095cac68 ffff0000 f2a5a028 ffff8008

X28: 0xffff8008f2a3bf90:
bf90  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfb0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfd0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bff0  00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
c010  00000000 00000000 f2a3c018 ffff8008 f2a3c018 ffff8008 08a067dc ffff0000
c030  f2a5a000 ffff8008 091c3650 ffff0000 f716fd18 ffff8008 f716fe30 ffff8008
c050  f2ce4a30 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
c070  f76c8010 ffff8008 f2ce4b00 ffff8008 095cac68 ffff0000 f2a5a028 ffff8008

Process irq/125-5b11000 (pid: 2457, stack limit = 0xffff00000b7b8000)
Call trace:
Exception stack(0xffff00000b7bba40 to 0xffff00000b7bbb80)
ba40: 732a010310b9ed00 ffff0000089ff8d0 0000000000000006 0000000000000000
ba60: 0000000000000001 0000000000000000 0000000000000001 ffff8008f27a9c90
ba80: ffff8008f2a98a90 ffff00000b7bbd00 0000000000000a30 0000000000000008
baa0: 0000000000000008 e35502e30d44349c f1866f5b952aca46 0000000000000000
bac0: ffff0000082b7c9c 0000000000000000 0000000000000000 ffff0000089ff000
bae0: ffff00000afae000 ffff8008f7a8b428 ffff000009c8e000 0000000000000409
bb00: ffff8008f2a3c010 00000000ffffffa1 0000000000000000 0000000000000001
bb20: ffff8008f2a3c010 ffff00000b7bbb80 ffff000008a032fc ffff00000b7bbb80
bb40: ffff0000089ffb3c 00000000800001c5 ffff00000b7bbb80 732a010310b9ed00
bb60: ffffffffffffffff ffff0000080f777c ffff00000b7bbb80 ffff0000089ffb3c
[<ffff0000089ffb3c>] composite_setup+0x44/0x1508
[<ffff000008a032fc>] android_setup+0xb8/0x13c
[<ffff0000089bd9a8>] cdns3_ep0_delegate_req+0x44/0x70
[<ffff0000089bdff4>] cdns3_check_ep0_interrupt_proceed+0x33c/0x654
[<ffff0000089bca44>] cdns3_device_thread_irq_handler+0x4b0/0x4bc
[<ffff0000089b77b4>] cdns3_thread_irq+0x48/0x68
[<ffff000008145bf0>] irq_thread_fn+0x28/0x88
[<ffff000008145e38>] irq_thread+0x13c/0x228
[<ffff0000080fed70>] kthread+0x104/0x130
[<ffff000008085064>] ret_from_fork+0x10/0x18

oops2:
composite_disconnect: Calling disconnect on a Gadget that is                      not connected
android_work: did not send uevent (0 0           (null))
init: Received control message 'stop' for 'adbd' from pid: 3359 (/vendor/bin/hw/android.hardware.usb@1.1-service.imx)
init: Sending signal 9 to service 'adbd' (pid 22343) process group...
------------[ cut here ]------------
audit: audit_lost=180038 audit_rate_limit=5 audit_backlog_limit=64
audit: rate limit exceeded
WARNING: CPU: 0 PID: 3468 at kernel_imx/drivers/usb/gadget/composite.c:2009 composite_disconnect+0x80/0x88
Modules linked in:
CPU: 0 PID: 3468 Comm: HWC-UEvent-Thre Not tainted 4.14.98-07846-g0b40a9b-dirty #16
Hardware name: Freescale i.MX8QM MEK (DT)
task: ffff8008f2349c00 task.stack: ffff00000b0a8000
PC is at composite_disconnect+0x80/0x88
LR is at composite_disconnect+0x80/0x88
pc : [<ffff0000089ff9b0>] lr : [<ffff0000089ff9b0>] pstate: 600001c5
sp : ffff000008003dd0
x29: ffff000008003dd0 x28: ffff8008f2349c00
x27: ffff000009885018 x26: ffff000008004000
Timeout for IPC response!
x25: ffff000009885018 x24: ffff000009c8e280
x23: ffff8008f2d98010 x22: 00000000000001c0
x21: ffff8008f2d98394 x20: ffff8008f2d98010
x19: 0000000000000000 x18: 0000e3956f4f075a
fxos8700 4-001e: i2c block read acc failed
x17: 0000e395735727e8 x16: ffff00000829f4d4
x15: ffffffffffffffff x14: 7463656e6e6f6320
x13: 746f6e2009090920 x12: 7369207461687420
x11: 7465676461472061 x10: 206e6f207463656e
x9 : 6e6f637369642067 x8 : ffff000009c8e280
x7 : ffff0000086ca6cc x6 : ffff000009f15e78
x5 : 0000000000000000 x4 : 0000000000000000
x3 : ffffffffffffffff x2 : c3f28b86000c3900
x1 : c3f28b86000c3900 x0 : 000000000000004e

X20: 0xffff8008f2d97f90:
7f90  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fb0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
libprocessgroup: Failed to kill process cgroup uid 0 pid 22343 in 215ms, 1 processes remain
7fd0
Timeout for IPC response!
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
using random self ethernet address
7ff0  00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
8010  00000100 00000000 f2d98018 ffff8008 f2d98018 ffff8008 08a067dc
using random host ethernet address
 ffff0000
8030  f206d800 ffff8008 091c3650 ffff0000 f7957b18 ffff8008 f7957730 ffff8008
8050  f716a630 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
8070  f76c8010 ffff8008 f716a800 ffff8008 095cac68 ffff0000 f206d828 ffff8008

X21: 0xffff8008f2d98314:
8314  ffff8008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8334  00000000 00000000 00000000 00000000 00000000 08a04cf4 ffff0000 00000000
8354  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8374  00000000 00000000 00000000 00001001 00000000 00000000 00000000 00000000
8394  e4bbe4bb 0f230000 ffff0000 0afae000 ffff0000 ae001000 00000000 f206d400
Timeout for IPC response!
83b4  ffff8008 00000000 00000000 f7957b18 ffff8008 f7957718 ffff8008 f7957018
83d4  ffff8008 f7957118 ffff8008 f7957618 ffff8008 f7957818 ffff8008 f7957918
83f4  ffff8008 f7957d18 ffff8008 00000000 00000000 00000000 00000000 00000000

X23: 0xffff8008f2d97f90:
7f90  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fb0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fd0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7ff0  00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
8010  00000100 00000000 f2d98018 ffff8008 f2d98018 ffff8008 08a067dc ffff0000
8030  f206d800 ffff8008 091c3650 ffff0000 f7957b18 ffff8008 f7957730 ffff8008
8050  f716a630 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
8070  f76c8010 ffff8008 f716a800 ffff8008 095cac68 ffff0000 f206d828 ffff8008

X28: 0xffff8008f2349b80:
9b80  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9ba0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9bc0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9be0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9c00  00000022 00000000 ffffffff ffffffff 00010001 00000000 00000000 00000000
9c20  0b0a8000 ffff0000 00000002 00404040 00000000 00000000 00000000 00000000
9c40  00000001 00000000 00000001 00000000 001ebd44 00000001 f390b800 ffff8008
9c60  00000000 00000001 00000070 00000070 00000070 00000000 09031d48 ffff0000

Call trace:
Exception stack(0xffff000008003c90 to 0xffff000008003dd0)
3c80:                                   000000000000004e c3f28b86000c3900
3ca0: c3f28b86000c3900 ffffffffffffffff 0000000000000000 0000000000000000
3cc0: ffff000009f15e78 ffff0000086ca6cc ffff000009c8e280 6e6f637369642067
3ce0: 206e6f207463656e 7465676461472061 7369207461687420 746f6e2009090920
3d00: 7463656e6e6f6320 ffffffffffffffff ffff00000829f4d4 0000e395735727e8
3d20: 0000e3956f4f075a 0000000000000000 ffff8008f2d98010 ffff8008f2d98394
3d40: 00000000000001c0 ffff8008f2d98010 ffff000009c8e280 ffff000009885018
3d60: ffff000008004000 ffff000009885018 ffff8008f2349c00 ffff000008003dd0
3d80: ffff0000089ff9b0 ffff000008003dd0 ffff0000089ff9b0 00000000600001c5
3da0: ffff8008f33f2cd8 0000000000000000 0000ffffffffffff 0000000000000000
init: Received control message 'start' for 'adbd' from pid: 3359 (/vendor/bin/hw/android.hardware.usb@1.1-service.imx)
3dc0: ffff000008003dd0 ffff0000089ff9b0
[<ffff0000089ff9b0>] composite_disconnect+0x80/0x88
[<ffff000008a044d4>] android_disconnect+0x3c/0x68
[<ffff0000089ba9f8>] cdns3_device_irq_handler+0xfc/0x2c8
[<ffff0000089b84c0>] cdns3_irq+0x44/0x94
[<ffff00000814494c>] __handle_irq_event_percpu+0x60/0x24c
[<ffff000008144c0c>] handle_irq_event+0x58/0xc0
[<ffff00000814873c>] handle_fasteoi_irq+0x98/0x180
[<ffff000008143a10>] generic_handle_irq+0x24/0x38
[<ffff000008144170>] __handle_domain_irq+0x60/0xac
[<ffff0000080819c4>] gic_handle_irq+0xd4/0x17c
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9bbfceea ]

In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.

Fixes: 1a7b12f6 ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1c20c89b ]

composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.

Consider the below sequence of function calls:
configfs_composite_bind()
        composite_dev_prepare()
                - Allocate cdev->req, cdev->req->buf
        composite_os_desc_req_prepare()
                - Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
        composite_dev_cleanup()
                - free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
        - If it fails goto err_comp_cleanup will call the
	  composite_dev_cleanup() function
        composite_dev_cleanup()
	        - calls kfree up with the stale values of cdev->req->buf and
		  cdev->os_desc_req from the previous configfs_composite_bind
		  call. The free call on these stale values leads to double free.

Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ba3a1a91 ]

Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.

Fixes: 914a3f3b ("USB: add atmel_usba_udc driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bc1e3a2d ]

Check memory resource existence before releasing it to avoid NULL
pointer dereference
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2bce1ebe ]

When a macsec interface is created, it increases a refcnt to a lower
device(real device). when macsec interface is deleted, the refcnt is
decreased in macsec_free_netdev(), which is ->priv_destructor() of
macsec interface.

The problem scenario is this.
When nested macsec interfaces are exiting, the exit routine of the
macsec module makes refcnt leaks.

Test commands:
    ip link add dummy0 type dummy
    ip link add macsec0 link dummy0 type macsec
    ip link add macsec1 link macsec0 type macsec
    modprobe -rv macsec

[  208.629433] unregister_netdevice: waiting for macsec0 to become free. Usage count = 1

Steps of exit routine of macsec module are below.
1. Calls ->dellink() in __rtnl_link_unregister().
2. Checks refcnt and wait refcnt to be 0 if refcnt is not 0 in
netdev_run_todo().
3. Calls ->priv_destruvtor() in netdev_run_todo().

Step2 checks refcnt, but step3 decreases refcnt.
So, step2 waits forever.

This patch makes the macsec module do not hold a refcnt of the lower
device because it already holds a refcnt of the lower device with
netdev_upper_dev_link().

Fixes: c09440f7 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 65de65d9 ]

The IFF_BONDING means bonding master or bonding slave device.
->ndo_add_slave() sets IFF_BONDING flag and ->ndo_del_slave() unsets
IFF_BONDING flag.

bond0<--bond1

Both bond0 and bond1 are bonding device and these should keep having
IFF_BONDING flag until they are removed.
But bond1 would lose IFF_BONDING at ->ndo_del_slave() because that routine
do not check whether the slave device is the bonding type or not.
This patch adds the interface type check routine before removing
IFF_BONDING flag.

Test commands:
    ip link add bond0 type bond
    ip link add bond1 type bond
    ip link set bond1 master bond0
    ip link set bond1 nomaster
    ip link del bond1 type bond
    ip link add bond1 type bond

Splat looks like:
[  226.665555] proc_dir_entry 'bonding/bond1' already registered
[  226.666440] WARNING: CPU: 0 PID: 737 at fs/proc/generic.c:361 proc_register+0x2a9/0x3e0
[  226.667571] Modules linked in: bonding af_packet sch_fq_codel ip_tables x_tables unix
[  226.668662] CPU: 0 PID: 737 Comm: ip Not tainted 5.4.0-rc3+ #96
[  226.669508] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  226.670652] RIP: 0010:proc_register+0x2a9/0x3e0
[  226.671612] Code: 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 39 01 00 00 48 8b 04 24 48 89 ea 48 c7 c7 a0 0b 14 9f 48 8b b0 e
0 00 00 00 e8 07 e7 88 ff <0f> 0b 48 c7 c7 40 2d a5 9f e8 59 d6 23 01 48 8b 4c 24 10 48 b8 00
[  226.675007] RSP: 0018:ffff888050e17078 EFLAGS: 00010282
[  226.675761] RAX: dffffc0000000008 RBX: ffff88805fdd0f10 RCX: ffffffff9dd344e2
[  226.676757] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f6b8c
[  226.677751] RBP: ffff8880507160f3 R08: ffffed100d940019 R09: ffffed100d940019
[  226.678761] R10: 0000000000000001 R11: ffffed100d940018 R12: ffff888050716008
[  226.679757] R13: ffff8880507160f2 R14: dffffc0000000000 R15: ffffed100a0e2c1e
[  226.680758] FS:  00007fdc217cc0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[  226.681886] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  226.682719] CR2: 00007f49313424d0 CR3: 0000000050e46001 CR4: 00000000000606f0
[  226.683727] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  226.684725] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  226.685681] Call Trace:
[  226.687089]  proc_create_seq_private+0xb3/0xf0
[  226.687778]  bond_create_proc_entry+0x1b3/0x3f0 [bonding]
[  226.691458]  bond_netdev_event+0x433/0x970 [bonding]
[  226.692139]  ? __module_text_address+0x13/0x140
[  226.692779]  notifier_call_chain+0x90/0x160
[  226.693401]  register_netdevice+0x9b3/0xd80
[  226.694010]  ? alloc_netdev_mqs+0x854/0xc10
[  226.694629]  ? netdev_change_features+0xa0/0xa0
[  226.695278]  ? rtnl_create_link+0x2ed/0xad0
[  226.695849]  bond_newlink+0x2a/0x60 [bonding]
[  226.696422]  __rtnl_newlink+0xb9f/0x11b0
[  226.696968]  ? rtnl_link_unregister+0x220/0x220
[ ... ]

Fixes: 0b680e75 ("[PATCH] bonding: Add priv_flag to avoid event mishandling")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c24b75e0 ]

syzbot reported the following issue :

BUG: KCSAN: data-race in update_defense_level / update_defense_level

read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
 update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
 defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
 process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
 worker_thread+0xa0/0x800 kernel/workqueue.c:2415
 kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352

write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
 update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
 defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
 process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
 worker_thread+0xa0/0x800 kernel/workqueue.c:2415
 kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler

Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.

Fixes: a0840e2e ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 62931f59 ]

if the IPVS module is removed while the sync daemon is starting, there is
a small gap where try_module_get() might fail getting the refcount inside
ip_vs_use_count_inc(). Then, the refcounts of IPVS module are unbalanced,
and the subsequent call to stop_sync_thread() causes the following splat:

 WARNING: CPU: 0 PID: 4013 at kernel/module.c:1146 module_put.part.44+0x15b/0x290
  Modules linked in: ip_vs(-) nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 veth ip6table_filter ip6_tables iptable_filter binfmt_misc intel_rapl_msr intel_rapl_common crct10dif_pclmul crc32_pclmul ext4 mbcache jbd2 ghash_clmulni_intel snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_intel_nhlt snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper joydev pcspkr snd_timer virtio_balloon snd soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi virtio_net net_failover virtio_blk failover virtio_console qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ata_piix ttm crc32c_intel serio_raw drm virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: nf_defrag_ipv6]
  CPU: 0 PID: 4013 Comm: modprobe Tainted: G        W         5.4.0-rc1.upstream+ #741
  Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
  RIP: 0010:module_put.part.44+0x15b/0x290
  Code: 04 25 28 00 00 00 0f 85 18 01 00 00 48 83 c4 68 5b 5d 41 5c 41 5d 41 5e 41 5f c3 89 44 24 28 83 e8 01 89 c5 0f 89 57 ff ff ff <0f> 0b e9 78 ff ff ff 65 8b 1d 67 83 26 4a 89 db be 08 00 00 00 48
  RSP: 0018:ffff888050607c78 EFLAGS: 00010297
  RAX: 0000000000000003 RBX: ffffffffc1420590 RCX: ffffffffb5db0ef9
  RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffffc1420590
  RBP: 00000000ffffffff R08: fffffbfff82840b3 R09: fffffbfff82840b3
  R10: 0000000000000001 R11: fffffbfff82840b2 R12: 1ffff1100a0c0f90
  R13: ffffffffc1420200 R14: ffff88804f533300 R15: ffff88804f533ca0
  FS:  00007f8ea9720740(0000) GS:ffff888053800000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007f3245abe000 CR3: 000000004c28a006 CR4: 00000000001606f0
  Call Trace:
   stop_sync_thread+0x3a3/0x7c0 [ip_vs]
   ip_vs_sync_net_cleanup+0x13/0x50 [ip_vs]
   ops_exit_list.isra.5+0x94/0x140
   unregister_pernet_operations+0x29d/0x460
   unregister_pernet_device+0x26/0x60
   ip_vs_cleanup+0x11/0x38 [ip_vs]
   __x64_sys_delete_module+0x2d5/0x400
   do_syscall_64+0xa5/0x4e0
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7f8ea8bf0db7
  Code: 73 01 c3 48 8b 0d b9 80 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 89 80 2c 00 f7 d8 64 89 01 48
  RSP: 002b:00007ffcd38d2fe8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
  RAX: ffffffffffffffda RBX: 0000000002436240 RCX: 00007f8ea8bf0db7
  RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00000000024362a8
  RBP: 0000000000000000 R08: 00007f8ea8eba060 R09: 00007f8ea8c658a0
  R10: 00007ffcd38d2a60 R11: 0000000000000206 R12: 0000000000000000
  R13: 0000000000000001 R14: 00000000024362a8 R15: 0000000000000000
  irq event stamp: 4538
  hardirqs last  enabled at (4537): [<ffffffffb6193dde>] quarantine_put+0x9e/0x170
  hardirqs last disabled at (4538): [<ffffffffb5a0556a>] trace_hardirqs_off_thunk+0x1a/0x20
  softirqs last  enabled at (4522): [<ffffffffb6f8ebe9>] sk_common_release+0x169/0x2d0
  softirqs last disabled at (4520): [<ffffffffb6f8eb3e>] sk_common_release+0xbe/0x2d0

Check the return value of ip_vs_use_count_inc() and let its caller return
proper error. Inside do_ip_vs_set_ctl() the module is already refcounted,
we don't need refcount/derefcount there. Finally, in register_ip_vs_app()
and start_sync_thread(), take the module refcount earlier and ensure it's
released in the error path.

Change since v1:
 - better return values in case of failure of ip_vs_use_count_inc(),
   thanks to Julian Anastasov
 - no need to increase/decrease the module refcount in ip_vs_set_ctl(),
   thanks to Julian Anastasov
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit daf61b02 ]

Other garbage collector might remove an entry not fully set up yet.

[570953.958293] RIP: 0010:memcmp+0x9/0x50
[...]
[570953.958567]  flow_offload_hash_cmp+0x1e/0x30 [nf_flow_table]
[570953.958585]  flow_offload_lookup+0x8c/0x110 [nf_flow_table]
[570953.958606]  nf_flow_offload_ip_hook+0x135/0xb30 [nf_flow_table]
[570953.958624]  nf_flow_offload_inet_hook+0x35/0x37 [nf_flow_table_inet]
[570953.958646]  nf_hook_slow+0x3c/0xb0
[570953.958664]  __netif_receive_skb_core+0x90f/0xb10
[570953.958678]  ? ip_rcv_finish+0x82/0xa0
[570953.958692]  __netif_receive_skb_one_core+0x3b/0x80
[570953.958711]  __netif_receive_skb+0x18/0x60
[570953.958727]  netif_receive_skb_internal+0x45/0xf0
[570953.958741]  napi_gro_receive+0xcd/0xf0
[570953.958764]  ixgbe_clean_rx_irq+0x432/0xe00 [ixgbe]
[570953.958782]  ixgbe_poll+0x27b/0x700 [ixgbe]
[570953.958796]  net_rx_action+0x284/0x3c0
[570953.958817]  __do_softirq+0xcc/0x27c
[570953.959464]  irq_exit+0xe8/0x100
[570953.960097]  do_IRQ+0x59/0xe0
[570953.960734]  common_interrupt+0xf/0xf

Fixes: 43c8f131 ("netfilter: nf_flow_table: fix missing error check for rhashtable_insert_fast")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c2ff2a36 ]

This patch fixes issue with Gen7 adapter in a blade environment where one
of the ports will not be detected by driver. Firmware expects mailbox 11 to
be set or cleared by driver for newer ISP.

Following message is seen in the log file:

[   18.810892] qla2xxx [0000:d8:00.0]-1820:1: **** Failed=102 mb[0]=4005 mb[1]=37 mb[2]=20 mb[3]=8
[   18.819596]  cmd=2 ****

[mkp: typos]

Link: https://lore.kernel.org/r/20191022193643.7076-2-hmadhani@marvell.comSigned-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>