hisi has a general dependency on ARCH_MULTIPLATFORM, which is
problematic when building a kernel for non-V7 platforms but selecting
drivers that might conflict with other architecture levels.

In this case, it broke my (still out of tree) patch set that
enables V7M multiplatform support, since that does not enable
MULTI_IRQ support:

arch/arm/kernel/built-in.o: In function `set_handle_irq':
arch/arm/kernel/irq.c:125: undefined reference to `handle_arch_irq'
arch/arm/kernel/built-in.o: In function `setup_arch':
arch/arm/kernel/setup.c:965: undefined reference to `handle_arch_irq'

Since all hisilicon platforms are ARMv7 based, we can avoid this
problem by just making the dependency more specific.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com>

UARTs on CNS3xxx are 8250-compatible, not AMBA.
The base address for UART0 is 0x78000000 (physical)
and 0xfb002000 (virtual).
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The newly introduced support for SAMA5D4 added access to the
'AT91_ALT_BASE_SYS' register area, but failed to define the
symbols in the case when CONFIG_MMU is disabled.

We really should not hardwire addresses like this any more,
but as a small fixup, this patch just adds the missing
definitions for the nommu case, which gets at91x40_defconfig
and any configuration of sam9 and sama5 with MMU disabled
back to work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 726d32bf ("ARM: at91: SAMA5D4 SoC detection code and low ...")

Pull "Second SoC batch for 3.18" from Nicolas Ferre:

- introduction of the new SAMA5D4 SoC and associated Evaluation Kit
- low level soc detection and early printk code
- taking advantage of this, documentation of all AT91 SoC DT strings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tag 'at91-soc2' of git://github.com/at91linux/linux-at91:
  ARM: at91: document Atmel SMART compatibles
  ARM: at91: add sama5d4 support to sama5_defconfig
  ARM: at91: dt: add device tree file for SAMA5D4ek board
  ARM: at91: dt: add device tree file for SAMA5D4 SoC
  ARM: at91: SAMA5D4 SoC detection code and low level routines
  ARM: at91: introduce basic SAMA5D4 support
  clk: at91: add a driver for the h32mx clock

The soc2 branch is based on this cleanup:

* at91/soc:
  ARM: at91: Remove the support for the RSI EWS board
  ARM: at91: remove board file for Acme Systems Fox G20
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'soc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

Pull "part 2 of omap SoC changes" from Tony Lindgren:

Few hwmod changes to support upcoming 8250 driver with DMA,
start using the SRAM driver for some omaps, and update the
defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tag 'soc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP4+: Remove static iotable mappings for SRAM
  ARM: OMAP4+: Move SRAM data to DT
  ARM: AM335x: Get rid of unused sram init function
  ARM: omap2plus_defconfig: Enable some display features
  ARM: omap2plus_defconfig: Enable battery and reset drivers
  ARM: omap2plus_defconfig: Add support for distros with systemd
  ARM: omap2plus_defconfig: Add cpufreq to defconfig
  ARM: omap2plus_defconfig: Shrink with savedefconfig
  ARM: OMAP3: Use manual idle for UARTs because of DMA errata
  ARM: OMAP2+: Add hwmod flag for HWMOD_RECONFIG_IO_CHAIN

Merge "ARM: BCM: Broadcom BCM63138 support" from Florian Fainelli:

This patchset adds very minimal support for the BCM63138 SoC which is
a xDSL SoC using a dual Cortex A9 CPU complex.

* tag 'bcm63138-v4' of http://github.com/brcm/linux:
  MAINTAINERS: add entry for the Broadcom BCM63xx ARM SoCs
  ARM: BCM63XX: add BCM963138DVT Reference platform DTS
  ARM: BCM63XX: add BCM63138 minimal Device Tree
  ARM: BCM63XX: add low-level UART debug support
  ARM: BCM63XX: add basic support for the Broadcom BCM63138 DSL SoC

Conflicts:
	arch/arm/Kconfig.debug
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Pull "Fifth Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:

* r8a7740: Fix documentation error copied from elsewhere
* r8a7794: Reserve memory for CMA in a manner consistent to
           other R-Car Gen2 SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7740 legacy: Fix copied bug in comment
  ARM: shmobile: r8a7794: Reserve memory as other R-Car Gen2 SoCs

Merge tag 'pxa3xx-ssp-name' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into next/soc

Pull "fix PXA3xx SSP naming issue" from Haojian Zhuang:

It's imported by 972a55b6 ASoC: fix pxa-ssp compiling issue under mach-mmp from v3.5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tag 'pxa3xx-ssp-name' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
  ARM: pxa3xx: provide specific platform_devices for all ssp ports
  ARM: pxa: ssp: provide platform_device_id for PXA3xx

Merge tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc

Pull "ARM: tegra: core SoC code changes for 3.18" from Stephen Warren:

the primary change here gets its address information from DT rather than
iomap.h. This removes one more user of iomap.h, and will help allow the
code to move to a location that can be shared between arch/arm and
arch/arm64.

An unused header file was also removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
  ARM: tegra: remove unused tegra_emc.h
  ARM: tegra: Initialize flow controller from DT
  of: Add NVIDIA Tegra flow controller bindings

Pull "arm: Xilinx Zynq cleanup patches for v3.18" from Michal Simek:

- PM support
- Fix L2 useless setting
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tag 'zynq-cleanup-for-3.18' of git://git.xilinx.com/linux-xlnx:
  ARM: zynq: Remove useless L2C AUX setting
  ARM: zynq: Rename 'zynq_platform_cpu_die'
  ARM: zynq: Remove hotplug.c
  ARM: zynq: Synchronise zynq_cpu_die/kill
  ARM: zynq: cpuidle: Remove pointless code
  ARM: zynq: Remove invalidate cache for cpu die
  ARM: zynq: PM: Enable DDR clock stop
  ARM: zynq: DT: Add DDRC node
  Documentation: devicetree: Add binding for Synopsys DDR controller
  ARM: zynq: PM: Enable A9 internal clock gating feature

This patch adds the basic machine file for the MesonX SoCs. Only Meson6
is populated.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add the UART definitions needed to support earlyprintk for MesonX SoCs
on UARTAO.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Export handle_fasteoi_irq to be able to use it in e.g. the Zynq gpio driver
since commit 6dd85950 ("gpio: zynq: Fix IRQ handlers").

This fixes the following link issue:

  ERROR: "handle_fasteoi_irq" [drivers/gpio/gpio-zynq.ko] undefined!
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Vincent Stehle <vincent.stehle@laposte.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1408663880-29179-1-git-send-email-vincent.stehle@laposte.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Merge tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc

Merge "ARM: imx: SoC updates for 3.18" from Shawn Guo:

The i.MX SoC updates for 3.18:
 - Add initial devicetree support for i.MX1
 - Support GPT per clock source from OSC for i.MX6
 - A couple of parent selection corrections for i.MX6SL clock driver
 - Support more chip revision for i.MX6
 - Convert pr_warning to pr_warn
 - Add exclusive gate clock support
 - Add BYPASS support for i.MX6 PLL clocks
 - Update i.MX6 clock tree for audio use case
 - A couple of VF610 clock driver updates

* tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
  ARM: imx_v6_v7_defconfig updates
  ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM
  arm: mach-imx: Convert pr_warning to pr_warn
  ARM: imx: source gpt per clk from OSC for system timer
  ARM: imx: add gpt_3m clk for i.mx6qdl
  ARM: imx: fix register offset of pll7_usb_host gate clock
  ARM: clk-imx6sl: refine clock tree for SSI
  ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver
  ARM: imx6sx: add BYPASS support for PLL clocks
  ARM: imx6sl: add BYPASS support for PLL clocks
  ARM: imx6q: add BYPASS support for PLL clocks
  ARM: imx: add an exclusive gate clock type
  ARM: clk-imx6q: refine clock tree for SSI
  ARM: clk-imx6q: refine clock tree for ASRC
  ARM: clk-imx6sl: correct the pxp and epdc axi clock selections
  ARM: clk-imx6q: refine clock tree for ESAI
  ARM: clk-imx6sl: Select appropriate parents for LCDIF clocks
  ARM: clk-imx6sl: Remove csi_lcdif_sels[]
  ARM: imx: clk-vf610: Add USBPHY clocks
  ARM: imx: add cpufreq support for i.mx6sx
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-soc4-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Merge "Fourth Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:

Fourth Round of Renesas ARM Based SoC Soc Updates for v3.18

* r8a7794: Remove unnecessary #ifdef CONFIG_USE_OF

* tag 'renesas-soc4-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7794: Remove unnecessary #ifdef CONFIG_USE_OF
Signed-off-by: Olof Johansson <olof@lixom.net>

Enable low-level debug for Mediatek mt6589 SoC on UART0.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

When compiling with "ARCH=arm" and "allmodconfig",
with commit: 9cdc9991 [2/7] ARM: hisi: enable MCPM implementation
we will get:

   /tmp/cc6DjYjT.s: Assembler messages:
   /tmp/cc6DjYjT.s:63: Error: selected processor does not support ARM mode `ubfx r1,r0,#8,#8'
   /tmp/cc6DjYjT.s:761: Error: selected processor does not support ARM mode `isb '
   /tmp/cc6DjYjT.s:762: Error: selected processor does not support ARM mode `dsb '
   /tmp/cc6DjYjT.s:769: Error: selected processor does not support ARM mode `isb '
   /tmp/cc6DjYjT.s:775: Error: selected processor does not support ARM mode `isb '
   /tmp/cc6DjYjT.s:776: Error: selected processor does not support ARM mode `dsb '
   /tmp/cc6DjYjT.s:795: Error: selected processor does not support ARM mode `isb '
   /tmp/cc6DjYjT.s:801: Error: selected processor does not support ARM mode `isb '
   /tmp/cc6DjYjT.s:802: Error: selected processor does not support ARM mode `dsb '

Fix platmcpm compilation when ARMv6 is selected.
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

HIP04 was added out of order, but so was the previous HISI debug uart
support as well. Minor reshuffling of order.
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "pull request for hisilicon hip04 soc and D01 board updates" from Wei Xu:

ARM: mach-hisi: Hisilicon hip04 soc and D01 board updates for 3.18

- Add the CONFIG_MCPM_QUAD_CLUSTER configuration to enlarge cluster number from 2 to 4
- Enable MCPM on HiP04 SoC
- Enable 16 cores on HiP04 SoC
- Add platform & Fabric controller devicetree binding document for HiP04 SoC
- Add hip04.dtsi & hip04-d01.dts for hip04 SoC platform and D01 board
- Enable HiP04 SoC in both hi3xxx_defconfig & multi_v7_defconfig
- Add the support of Hisilicon HiP04 debug uart

* tag 'D01-for-3.18' of git://github.com/hisilicon/linux-hisi:
  ARM: debug: add HiP04 debug uart
  ARM: config: enable hisilicon hip04
  ARM: dts: add hip04 dts
  document: dt: add the binding on HiP04
  ARM: hisi: enable HiP04
  ARM: hisi: enable MCPM implementation
  ARM: mcpm: support 4 clusters
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-clk2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Merge "Second Round of Renesas ARM Based SoC Clk Updates for v3.18" from Simon Horman.

* Add r8a7740, sh73a0 SoCs to MSTP bindings

* tag 'renesas-clk2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  clk: shmobile: Add r8a7740, sh73a0 SoCs to MSTP bindings
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

SoC related changes for omaps for v3.18 merge window:

- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options

Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.

* tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (514 commits)
  ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
  ARM: dts: OMAP3+: Add PRM interrupt
  ARM: omap: Remove stray ARCH_HAS_OPP references
  ARM: DRA7: Add hook in SoC initcalls to enable pm initialization
  ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
  ARM: OMAP5 / DRA7: Enable CPU RET on suspend
  ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
  ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
  ARM: OMAP5 / DRA7: PM: Enable Mercury retention mode on CPUx powerdomains
  ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default
  ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
  ARM: OMAP5 / DRA7: PM: Update CPU context register offset
  ARM: AM437x: use pdata quirks for pinctrl information
  ARM: DRA7: use pdata quirks for pinctrl information
  ARM: OMAP5: use pdata quirks for pinctrl information
  ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
  ARM: OMAP4+: PM: use only valid low power state for suspend
  ARM: OMAP4+: PM: Make logic state programmable
  ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
  ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
  ...

Document all the available compatibles for Atmel "SMART" SoCs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add sama5d4 to sama5_defconfig to build kernel booting on both sama5d3 and
samad4.

Note that earlyprintk can only be working for one or the other.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add reference SAMA5D4-EK platform DT file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add SAMA5D4 SoC DT file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

SoC identification code, kernel uncompress and low level
debugging routines update.
On SAMA5D4, DBGU is at another address AT91_BASE_DBGU2 so another
round of detection is needed. We also had to differentiate with
SAMA5D3 SoC family and rename some variables.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Currently, devices for SSP ports 1, 2 and 3 are registered as compatible
devices to pxa27x-ssp. While the actual IP core is comparable, there are
some subtle differences which users of the SSP ports address by looking at
the 'type' field.

By registering devices of type 'pxa27x-ssp', this 'type' field is
incorrectly set to PXA27x_SSP which confuses the users.

To fix this, provide specific ssp port plaform devices which use
'pxa3xx-ssp' as driver name, an instantiate them from pxa3xx.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Provide an explicit match string for PXA3xx SSP ports.

Without this match string, SSP0/SSP1/SSP2 in PXA3xxx will be consided as
PXA27x SSP Port.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

In order to handle errata I688, a page of sram was reserved by doing a
static iotable map. Now that we use gen_pool to manage sram, we can
completely remove all of these static mappings and use gen_pool_alloc()
to get the one page of sram space needed to implement errata I688.
omap_bus_sync will be NOP until SRAM initialization happens.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use drivers/misc/sram.c driver to manage SRAM on all DT only
OMAP platforms (am33xx, am43xx, omap4 and omap5) instead of
the existing private plat-omap/sram.c

Address and size related data  is removed from mach-omap2/sram.c
and now passed to drivers/misc/sram.c from DT.

Users can hence use general purpose allocator apis instead of
OMAP private ones to manage and use SRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove the empty am33xx_sram_init() function.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Now that we have panel support for DT based booting,
let's make it usable and enable most things as modules.

Note that omap3 boards need also the ads7847 module for
the panel that we're now changing to a loadable module.
And n900 seems to require setting the brightness via
sysfs for acx565akm/brightness after modprobe of
panel_sony_acx565akm and omapfb.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since many omaps run on battery, we should have the battery
drivers enabled. Let's also enable the reset driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Some distros are now using systemd, so let's enable most of
what's recommended at:

http://cgit.freedesktop.org/systemd/systemd/tree/READMEReviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Note that we can now use the CONFIG_GENERIC_CPUFREQ_CPU0,
so let's only enable that. Let's use CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND
as suggested by Nishant.

And also let's enable thermal as explained by Nishant Menon:

Many TI SoCs using Highest frequency is not really too nice of an idea for
long periods of time. And not everything is upstream to support things
optimially - example avs class 0, 1.5 ABB consolidation with cpufreq etc..
We definitely need thermal enabled as well for device safety needs.

[tony@atomide.com: updated per Nishant's suggestions]
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This saves few lines and makes it easier to make patches
against omap2plus_defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>