Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-10-01

This series contains updates to ice driver only.

Anirudh provides several changes to "prep" the driver for upcoming
features.  Specifically, the functions that are used for PF VSI/netdev
setup will also be used in SR-IOV support and to allow the reuse of
these functions, code needs to move.

Dave provides the only other change in the series, updates the driver to
protect the reset patch in its entirety.  This is done by adding the
various bit checks to determine if a reset is scheduled/initiated and
whether it came from the software or firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, there is no bit, or set of bits, that protect the entirety
of the reset path.

If the reset is originated by the driver, then the relevant
one of the following bits will be set when the reset is scheduled:
__ICE_PFR_REQ
__ICE_CORER_REQ
__ICE_GLOBR_REQ
This bit will not be cleared until after the rebuild has completed.

If the reset is originated by the FW, then the first the driver knows of
it will be the reception of the OICR interrupt.  The __ICE_RESET_OICR_RECV
bit will be set in the interrupt handler.  This will also be the indicator
in a SW originated reset that we have completed the pre-OICR tasks and
have informed the FW that a reset was requested.

To utilize these bits, change the function:
ice_is_reset_recovery_pending()
	to be:
ice_is_reset_in_progress()

The new function will check all of the above bits in the pf->state and
will return a true if one or more of these bits are set.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch completes the code move out of ice_main.c

The following top level functions and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup
ice_vsi_cfg_tc

The following functions were made static again:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs
void ice_vsi_map_rings_to_vectors
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_alloc_arrays
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs

The following functions were made static again:
ice_vsi_free_arrays
ice_vsi_clear_rings

Also, in this patch, the netdev and NAPI registration logic was de-coupled
from the VSI creation logic (ice_vsi_setup) as for SR-IOV, while we want to
create VF VSIs using ice_vsi_setup, we don't want to create netdevs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_clear
ice_vsi_close
ice_vsi_free_arrays
ice_vsi_map_rings_to_vectors
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_clear_rings
ice_vsi_alloc_arrays
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_delete
ice_free_res
ice_get_res
ice_is_reset_recovery_pending
ice_vsi_put_qs
ice_vsi_dis_irq
ice_vsi_free_irq
ice_vsi_free_rx_rings
ice_vsi_free_tx_rings
ice_msix_clean_rings
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_start_rx_rings
ice_vsi_stop_rx_rings
ice_vsi_stop_tx_rings
ice_vsi_cfg_rxqs
ice_vsi_cfg_txqs
ice_vsi_cfg_msix
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The functions that are used for PF VSI/netdev setup will also be used
for SR-IOV support. To allow reuse of these functions, move these
functions out of ice_main.c to ice_common.c/ice_lib.c

This move is done across multiple patches. Each patch moves a few
functions and may have minor adjustments. For example, a function that was
previously static in ice_main.c will be made non-static temporarily in
its new location to allow the driver to build cleanly. These adjustments
will be removed in subsequent patches where more code is moved out of
ice_main.c

In this particular patch, the following functions were moved out of
ice_main.c:
int ice_add_mac_to_list
ice_free_fltr_list
ice_stat_update40
ice_stat_update32
ice_update_eth_stats
ice_vsi_add_vlan
ice_vsi_kill_vlan
ice_vsi_manage_vlan_insertion
ice_vsi_manage_vlan_stripping
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the bug that all datapath and vport ops are returning
wrong values (OVS_FLOW_CMD_NEW or OVS_DP_CMD_NEW) in their replies.
Signed-off-by: Yifeng Sun <pkusunyifeng@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Structure 'tls_rec' contains sg_aead_in and sg_aead_out which point
to a aad_space and then chain scatterlists sg_plaintext_data,
sg_encrypted_data respectively. Rather than using chained scatterlists
for plaintext and encrypted data in aead_req, it is efficient to store
aad_space in sg_encrypted_data and sg_plaintext_data itself in the
first index and get rid of sg_aead_in, sg_aead_in and further chaining.

This requires increasing size of sg_encrypted_data & sg_plaintext_data
arrarys by 1 to accommodate entry for aad_space. The code which uses
sg_encrypted_data and sg_plaintext_data has been modified to skip first
index as it points to aad_space.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: make connection setup more robust

In this series we make a few improvements to the connection setup and
probing mechanism, culminating in the last commit where we make it
possible for a client socket to make multiple setup attempts in case
it encounters receive buffer overflow at the listener socket.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Default socket receive buffer size for a listener socket is 2Mb. For
each arriving empty SYN, the linux kernel allocates a 768 bytes buffer.
This means that a listener socket can serve maximum 2700 simultaneous
empty connection setup requests before it hits a receive buffer
overflow, and much fewer if the SYN is carrying any significant
amount of data.

When this happens the setup request is rejected, and the client
receives an ECONNREFUSED error.

This commit mitigates this problem by letting the client socket try to
retransmit the SYN message multiple times when it sees it rejected with
the code TIPC_ERR_OVERLOAD. Retransmission is done at random intervals
in the range of [100 ms, setup_timeout / 4], as many times as there is
room for within the setup timeout limit.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Messages intended for intitating a connection are currently
indistinguishable from regular datagram messages. The TIPC
protocol specification defines bit 17 in word 0 as a SYN bit
to allow sanity check of such messages in the listening socket,
but this has so far never been implemented.

We do that in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We refactor the function tipc_sk_filter_connect(), both to make it
more readable and as a preparation for the next commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We refactor this function as a preparation for the coming commits in
the same series.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function tipc_msg_reverse() is reversing the header of a message
while reusing the original buffer. We have seen at several occasions
that this may have unfortunate side effects when the buffer to be
reversed is a clone.

In one of the following commits we will again need to reverse cloned
buffers, so this is the right time to permanently eliminate this
problem. In this commit we let the said function always consume the
original buffer and replace it with a new one when applicable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously TCP initial receive buffer is ~87KB by default and
the initial receive window is ~29KB (20 MSS). This patch changes
the two numbers to 128KB and ~64KB (rounding down to the multiples
of MSS) respectively. The patch also simplifies the calculations s.t.
the two numbers are directly controlled by sysctl tcp_rmem[1]:

  1) Initial receiver buffer budget (sk_rcvbuf): while this should
     be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf()
     always override and set a larger size when a new connection
     establishes.

  2) Initial receive window in SYN: previously it is set to 20
     packets if MSS <= 1460. The number 20 was based on the initial
     congestion window of 10: the receiver needs twice amount to
     avoid being limited by the receive window upon out-of-order
     delivery in the first window burst. But since this only
     applies if the receiving MSS <= 1460, connection using large MTU
     (e.g. to utilize receiver zero-copy) may be limited by the
     receive window.

With this patch TCP memory configuration is more straight-forward and
more properly sized to modern high-speed networks by default. Several
popular stacks have been announcing 64KB rwin in SYNs as well.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function ‘hclge_get_sset_count’:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:496:31: error: ‘HNAE3_REVISION_ID_21’ undeclared (first use in this function); did you mean ‘FADT2_REVISION_ID’?
   if (hdev->pdev->revision >= HNAE3_REVISION_ID_21 ||
                               ^~~~~~~~~~~~~~~~~~~~
                               FADT2_REVISION_ID
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c: In function ‘hns3_self_test’:
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c:278:15: error: ‘HNS3_SELF_TEST_TYPE_NUM’ undeclared (first use in this function); did you mean ‘HNS3_SELF_TEST_TPYE_NUM’?
  int st_param[HNS3_SELF_TEST_TYPE_NUM][2];
               ^~~~~~~~~~~~~~~~~~~~~~~
               HNS3_SELF_TEST_TPYE_NUM
Signed-off-by: David S. Miller <davem@davemloft.net>

rx_mini_pending was set to an incorrect value. This was causing EINVAL to
always be returned to 'ethtool -G'. The driver does not support mini or
jumbo rings so the respective settings should be zero.

Also, change the valid range of the number of descriptors in the rings to
make the code simpler and easier for users to understand (this removes the
valid settings of 8 and 16). Add a system log message indicating when the
number is rounded-up from what the user specifies with the 'ethtool -G'
command (i.e. when it is not a multiple of 32), and update the log message
when a user-provided value is out of range to also indicate the stride.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes a couple of changes in the way the driver uses the
"get capabilities" command.

1. Get device capabilities in addition to function capabilities

2. Align to latest spec by using cap_count to determine size of the
   buffer in case of length error.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Query the Tx scheduler tree node information from FW before adding it to
the driver's software database. This will keep the node information current
in driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously the comment stated that VSI lists should be used when a
second VSI becomes a subscriber to the "VLAN address". VSI lists
are always used for VLAN membership, so replace "VLAN address" with
"MAC address". Also note that VLAN(s) always use VSI list rules.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and
MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a
firmware version is newer than expected. This is currently tested by
comparing each field separately. Thus, we compare the branch field
against the MAX_FW_API_VER_BRANCH, and so forth.

This means that currently, if we suppose that the max firmware version
is defined as 0.2.1, i.e.

Then firmware 0.1.3 will fail to load. This is because the minor version
3 is greater than the max minor version 1.

This is not intuitive, because of the notion that increasing the major
firmware version to 2 should mean any firmware version with a major
version is less than 2 should be considered older than 2...

In order to allow both 0.2.1 and 0.1.3 to load, you would have to define
the "max" firmware version as 0.2.3.. It is possible that such
a firmware version doesn't even exist yet!

Fix this by replacing the current logic with an updated check that
behaves as follows:

First, we check the major version. If it is greater than the expected
version, then we prevent driver load. Additionally, a warning message is
logged to indicate to the system administrator that they need to update
their driver. This is now the only case where the driver will refuse to
load.

Second, if the major version is less than the expected version, we log
an information message indicating the NVM should be updated.

Third, if the major version is exact, we'll then check the minor
version. If the minor version is more than two versions less than
expected, we log an information message indicating the NVM should be
updated. If it is more than two versions greater than the expected
version, we log an information message that the driver should be
updated.

To support this, the ice_aq_ver_check function needs its signature
updated to pass the HW structure. Since we now pass this structure,
there is no need to pass the firmware API versions separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update branding strings and remove device ids 0x1594 and 0x1595.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Direct assignment is preferred over a memcpy()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When shutting down the controlqs, we check if they are initialized
before we shut them down and destroy the lock. This is important, as it
prevents attempts to access the lock of an already shutdown queue.

Unfortunately, we checked rq.head and sq.head as the value to determine
if the queue was initialized. This doesn't work, because head is not
reset when the queue is shutdown. In some flows, the adminq will have
already been shut down prior to calling ice_shutdown_all_ctrlqs. This
can result in a crash due to attempting to access the already destroyed
mutex.

Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq
and ice_shutdown_rq already indicate that this is the value we should be
using to determine of the queue was initialized.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-09-27

This series contains fixes to the ice driver only.

Jake fixes a potential crash due to attempting to access the mutex which
is already destroyed.  Fix this by using rq.count and sq.count to
determine if the queue was initialized.  Fixed the current logic for
checking the firmware version to properly handle situations when
firmware major/minor versions differ and when the branch version
differs.

Bruce replaces a memcpy() with a direct assignment, which is preferred.
Also updated the branding strings and device ids supported by the
driver.  Fixed the "ethtool -G" command in the driver, which was always
returning EINVAL when changing the descriptor ring size.

Brett update and clarified code comments.

Anirudh updates the driver to ensure we query the firmware for the
transmit scheduler node information before adding it to the driver
database, to ensure we have the current information.  Also update the
"get capabilities" command to get device and function capabilities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

net/sched/sch_generic.c:944:6: warning:
 symbol 'qdisc_free_cb' was not declared. Should it be static?

Fixes: 3a7d0d07 ("net: sched: extend Qdisc with rcu")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This test adds an fdb entry with the sticky flag and sends traffic from
a different port with the same mac as a source address expecting the entry
to not change ports if the flag is operating correctly.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to explicitly zero is_sticky when creating a new fdb, otherwise
we might get a stale value for a new entry.

Fixes: 435f2e7c ("net: bridge: add support for sticky fdb entries")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Cleanups, minor additions & fixes for HNS3 driver

This patch-set contains cleans-ups, minor changes and fixes to the HNS3 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.

Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hclge_tm_schd_info_update should return an error when num_tc is greater
than alloc_tqps.

This patch changes the return type of hnae3_register_ae_algo from void
to int.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.

This patch fixes it by not returning when the setting fails.

Fixes: a8e8b7ff ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware expects a unit of 128 bytes when setting
packet buffer. When calculating the packet buffer size,
hclge_rx_buffer_calc does not round up the size as a unit
of 128 byte, which may casue packet lost problem when stress
testing.

This patch fixes it by rounding up packet size when calculating.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds serdes parallel inner loopback support for self test.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>