This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs:
serial_cs:
    add new id (TOSHIBA Modem/LAN Card)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Issuing the following command on host:

$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1

Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:

  skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
  ------------[ cut here ]------------
  kernel BUG at net/core/skbuff.c:127!
  Oops: Exception in kernel mode, sig: 5 [#1]
  MPC831x RDB
  last sysfs file: /sys/kernel/uevent_seqnum
  Modules linked in:
  NIP: c01c1840 LR: c01c1840 CTR: c016d918
  [...]
  NIP [c01c1840] skb_over_panic+0x48/0x5c
  LR [c01c1840] skb_over_panic+0x48/0x5c
  Call Trace:
  [c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
  [c0339d60] [c01c3020] skb_put+0x5c/0x60
  [c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
  [c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc

Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:

  status=1400 length=1536
  status=1800 length=1541

So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.

This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).

Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port reset operations and memory add/remove operations need to
be serialized to avoid a kernel deadlock. The deadlock is caused
by calling the napi_disable() function twice.
Therefore we have to employ the dlpar_mem_lock in the ehea_reset_port
function as well
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the eHEA poll function an rmb() is required. Without that some packets
on the receive queue are not seen and thus delayed until the next interrupt
is handled for the same receive queue.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These comments were forgotten in the initial patch to add this
functionality.  This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

https://bugzilla.kernel.org/show_bug.cgi?id=16183

The sch_teql module, which can be used to load balance over a set of
underlying interfaces, stopped working after 2.6.30 and has been
broken in all kernels since then for any underlying interface which
requires the addition of link level headers.

The problem is that the transmit routine relies on being able to
access the destination address in the skb in order to do address
resolution once it has decided which underlying interface it is going
to transmit through.

In 2.6.31 the IFF_XMIT_DST_RELEASE flag was introduced, and set by
default for all interfaces, which causes the destination address to be
released before the transmit routine for the interface is called.

The solution is to clear that flag for teql interfaces.
Signed-off-by: Tom Hughes <tom@compton.nu>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the RCTRL_TS_ENABLE bit was set unconditionally. However, if
the RCTRL_TS_ENABLE is set without TMR_CTRL[TE], the driver does not work
properly on some boards (Anton had problems with the MPC8313ERDB and
MPC8568EMDS).

With this patch the bit will only be set if requested from user space
with the SIOCSHWTSTAMP ioctl command, meaning that time stamping is
disabled during normal operation. Users who are not interested in time
stamps will not experience problems with buggy CPU revisions or
performance drops any more.

The setting of TMR_CTRL[TE] is still up to the user. This is considered
safe because users wanting HW timestamps must initialize the eTSEC clock
first anyway, e.g. with the recently submitted PTP clock driver.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

regression introduced by b8d92c9c

In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function

this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The bridge multicast patches introduced an OOM crash in the forward
path, when deliver_clone fails to clone the skb.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

CRB window register is not per pci-func for NX3031,
so caching can result in incorrect values.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rcv producer should be read in spin-lock.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes memory leak in error path when memory allocation
for adapter data structures fails.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch c7c2fa07 removed one line too much from smc91c92_cs.c.
Reported-by: Komuro <komurojun-mbn@nifty.com>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Avoids this:

WARNING: at net/mac80211/scan.c:312 ieee80211_scan_completed+0x5f/0x1f1
[mac80211]()
Hardware name: Latitude E5400
Modules linked in: aes_x86_64 aes_generic fuse ipt_MASQUERADE iptable_nat
nf_nat rfcomm sco bridge stp llc bnep l2cap sunrpc cpufreq_ondemand
acpi_cpufreq freq_table xt_physdev ip6t_REJECT nf_conntrack_ipv6
ip6table_filter ip6_tables ipv6 kvm_intel kvm uinput arc4 ecb
snd_hda_codec_intelhdmi snd_hda_codec_idt snd_hda_intel iwlagn snd_hda_codec
snd_hwdep snd_seq snd_seq_device iwlcore snd_pcm dell_wmi sdhci_pci sdhci
iTCO_wdt tg3 dell_laptop mmc_core i2c_i801 wmi mac80211 snd_timer
iTCO_vendor_support btusb joydev dcdbas cfg80211 bluetooth snd soundcore
microcode rfkill snd_page_alloc firewire_ohci firewire_core crc_itu_t
yenta_socket rsrc_nonstatic i915 drm_kms_helper drm i2c_algo_bit i2c_core video
output [last unloaded: scsi_wait_scan]
Pid: 979, comm: iwlagn Tainted: G        W  2.6.33.3-85.fc13.x86_64 #1
Call Trace:
[<ffffffff8104b558>] warn_slowpath_common+0x77/0x8f
[<ffffffff8104b57f>] warn_slowpath_null+0xf/0x11
[<ffffffffa01bb7d9>] ieee80211_scan_completed+0x5f/0x1f1 [mac80211]
[<ffffffffa02a23f0>] iwl_bg_scan_completed+0xbb/0x17a [iwlcore]
[<ffffffff81060d3d>] worker_thread+0x1a4/0x232
[<ffffffffa02a2335>] ? iwl_bg_scan_completed+0x0/0x17a [iwlcore]
[<ffffffff81064817>] ? autoremove_wake_function+0x0/0x34
[<ffffffff81060b99>] ? worker_thread+0x0/0x232
[<ffffffff810643c7>] kthread+0x7a/0x82
[<ffffffff8100a924>] kernel_thread_helper+0x4/0x10
[<ffffffff8106434d>] ? kthread+0x0/0x82
[<ffffffff8100a920>] ? kernel_thread_helper+0x0/0x10

Reported here:

	https://bugzilla.redhat.com/show_bug.cgi?id=590436Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Mihai Harpau <mishu@piatafinanciara.ro>
Cc: stable@kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: stable@kernel.org
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes linux-2.6 warning:

drivers/net/wireless/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/libertas_tf/main.c:578: warning: 'stats.antenna' is used uninitialized in this function
drivers/net/wireless/libertas_tf/main.c:578: warning: 'stats.mactime' is used uninitialized in this function

stats struct needs to be set to 0 before use.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The flow id (scd_flow) in a compressed BA packet should match the txq_id
of the queue from which the aggregated packets were sent. However, in
some hardware like the 1000 series, sometimes the flow id is 0 for the
txq_id (10 to 19). This can cause the annoying message:
[ 2213.306191] iwlagn 0000:01:00.0: Received BA when not expected
[ 2213.310178] iwlagn 0000:01:00.0: Read index for DMA queue txq id (0),
index 5, is out of range [0-256] 7 7.

And even worse, if agg->wait_for_ba is true when the bad BA is arriving,
this can cause system hang due to NULL pointer dereference because the
code is operating in a wrong tx queue!
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Pradeep Kulkarni <pradeepx.kulkarni@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

We are seeing some race conditions between incoming station management
requests (station add/remove) and the internal unassoc RXON command that
modifies station table. Modify these flows to require the mutex to be held
and thus serializing them.

This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2207Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This patch added to 2.6.34:

	commit f8d1dcaf
	Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
	Date:   Tue Apr 27 01:37:20 2010 +0000

	    ixgbe: enable extremely low latency

introduced a feature where LRO (called RSC on the hardware) was disabled
automatically when setting rx-usecs to 0 via ethtool.  Some might not
like the fact that LRO was disabled automatically, but I'm fine with
that.  What I don't like is that LRO/RSC is automatically enabled when
rx-usecs is set >0 via ethtool.

This would certainly be a problem if the device was used for forwarding
and it was determined that the low latency wasn't needed after the
device was already forwarding.  I played around with saving the state of
LRO in the driver, but it just didn't seem worthwhile and would require
a small change to dev_disable_lro() that I did not like.

This patch simply leaves LRO disabled when setting rx-usecs >0 and
requires that the user enable it again.  An extra informational message
will also now appear in the log so users can understand why LRO isn't
being enabled as they expect.

Inconsistency of LRO setting first noticed by Stanislaw Gruszka.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
CC: stable@kernel.org
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 675ad473
removed the capability to use ethtool.set_msglevel to
control the types of messages emitted by the driver.

That commit should probably be reverted.

If not, then this patch fixes a message logging defect
introduced by converting a printk without KERN_<level>
to e_info.

This also reduces text by about 200 bytes.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a small window where the watchdog could be running as the
interface is brought down on a NIC with two ports wired back to back.
If ixgbe_update_status is then called can lead to a panic.  This patch
allows the update to bail if we are in that condition.

This issue was orignally reported and fix proposed by Akihiko Saitou.

CC: Akihiko Saitou <asaitou@users.sourceforge.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to copy rxhash again in __skb_clone()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

deliver_no_wcard is not being set in skb_copy_header.
In the skb_cloned case it is not being cleared and
may cause the skb to be dropped when the loopback device
pushes it back up the stack.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix build warning on i386 (32-bit) with 32-bit dma_addr_t:

drivers/net/enic/vnic_dev.c: In function 'vnic_dev_init_prov':
drivers/net/enic/vnic_dev.c:716: warning: passing argument 3 of 'pci_alloc_consistent' from incompatible pointer type
include/asm-generic/pci-dma-compat.h:16: note: expected 'dma_addr_t *' but argument is of type 'u64 *'

Now builds without warnings on i386 and on x86_64.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc:	Scott Feldman <scofeldm@cisco.com>
Cc:	Vasanthy Kolluri <vkolluri@cisco.com>
Cc:	Roopa Prabhu <roprabhu@cisco.com>
Acked-by: Scott Feldman <scofeldm@cisco.com>

i2400m_fw_hdr_check() was accessing hardware field
bcf_hdr->module_type (little endian 32) without converting to host
byte sex.
Reported-by: Данилин Михаил <mdanilin@nsg.net.ru>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>

fix a race at the end of NAPI complete processing, it had
better do __napi_complete() first before re-enable interrupt.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch correct a bug in the delay of pktgen. 
It makes sure the inter-packet interval is accurate.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

gen_kill_estimator() / gen_new_estimator() is not always called with
RTNL held.

net/netfilter/xt_RATEEST.c is one user of these API that do not hold
RTNL, so random corruptions can occur between "tc" and "iptables".

Add a new fine grained lock instead of trying to use RTNL in netfilter.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop().  This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.

For example,

vlanx -> bond0 -> ethx

will be dropped in the vlan path and not delivered to any
packet handlers at all.  However,

bond0 -> vlanx -> ethx

and

bond0 -> ethx

will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.

This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv().  Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly.  This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.

I have tested the following 4 configurations in failover modes
and load balancing modes.

# bond0 -> ethx

# vlanx -> bond0 -> ethx

# bond0 -> vlanx -> ethx

# bond0 -> ethx
            |
  vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1f8438a8 (icmp: Account for ICMP out errors), I did a typo
on IPV6 side, using ICMP6_MIB_OUTMSGS instead of ICMP6_MIB_OUTERRORS
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cc772ab7 ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).

That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:

  Timestamp incoming packets as padding bytes. PAL field is set
  to 8 if the PAL field is programmed to less than 8. Must be set
  to zero if TMR_CTRL[TE]=0.

I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.

Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.

For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The extra ! character means that these conditions are always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>