Fix section mismatch and remove unused variable 'tmp'.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Commit e391be76 (MIPS: Alchemy: Clean up GPIO registers and accessors)
changed the way the GPIO was toggled. Prior to this patch, we would
always actively drive the GPIO output to either 0 or 1, this patch
drove the GPIO active to 0, and put the GPIO in tristate to drive it
to 1, unfortunately this does not work, revert back to active driving.

Using a signed variable (gstate) to hold the gpio state and using a bit-
wise operation on it also resulted in toggling value from 1 to -2 since
the variable is signed. This value was then passed on to gpio_direction_
output, which always perform a if (value) ... to set the value to the
gpio, so we were always writing a 1 to this GPIO instead of 1 -> 0 -> 1 ...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

Otherwise, the gpiolib autorequest feature will produce a WARN_ON():

WARNING: at drivers/gpio/gpiolib.c:101 0x8020ec6c()
autorequest GPIO-215
[...]
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

Due to the whole single instance based watchdog API we use static data
for the wm831x watchdog which means that if the system tries to register
a second one we end up trying to register the same miscdevice again,
corrupting the miscdevice list. Work around this by checking for duplicate
registrations until we get a watchdog core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.

Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The interface to ->truncate_range is changing very slightly: once "tmpfs:
take control of its truncate_range" has been applied, this can be applied.
 For now there is only a slight inefficiency while this remains unapplied,
but it will soon become essential for managing shmem's use of swap.

Change i915_gem_object_truncate() to use shmem_truncate_range() directly:
which should also spare i915 later change if we switch from
inode_operations->truncate_range to file_operations->fallocate.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Soon tmpfs will stop supporting ->readpage and read_cache_page_gfp(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.

Make i915_gem_object_get_pages_gtt() use shmem_read_mapping_page_gfp() in
the one place it's needed; elsewhere use shmem_read_mapping_page(), with
the mapping's gfp_mask properly initialized.

Forget about __GFP_COLD: since tmpfs initializes its pages with memset,
asking for a cold page is counter-productive.

Include linux/shmem_fs.h also in drm_gem.c: with shmem_file_setup() now
declared there too, we shall remove the prototype from linux/mm.h later.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Soon tmpfs will stop supporting ->readpage and read_mapping_page(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.

ttm_tt_swapin() and ttm_tt_swapout() use shmem_read_mapping_page() in
place of read_mapping_page(), since their swap_space has been created with
shmem_file_setup().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fis the warning

  drivers/tty/serial/8250_pci.c:1457: warning: initialization from incompatible pointer type

Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix this section mismatch:

  WARNING: drivers/misc/ioc4.o(.data+0x144): Section mismatch in reference from the variable ioc4_load_modules_work to the function .devinit.text:ioc4_load_modules()
  The variable ioc4_load_modules_work references
  the function __devinit ioc4_load_modules()
  If the reference is valid then annotate the
  variable with __init* or __refdata (see linux/init.h) or name the variable:
  *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console

This one is potentially fatal; by the time ioc4_load_modules is invoked
it may already have been freed.  For that reason ioc4_load_modules_work
can't be turned to __devinitdata but also because it's referenced in
ioc4_exit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Brent Casavant <bcasavan@sgi.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix this section mismatch:

  WARNING: drivers/leds/leds-lp5523.o(.text+0x12f4): Section mismatch in reference from the function lp5523_probe() to the function .init.text:lp5523_init_led()
  The function lp5523_probe() references
  the function __init lp5523_init_led().
  This is often because lp5523_probe lacks a __init
  annotation or the annotation of lp5523_init_led is wrong.

Fixing this one triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix this section mismatch:

  WARNING: drivers/leds/leds-lp5521.o(.text+0xf2c): Section mismatch in reference from the function lp5521_probe() to the function .init.text:lp5521_init_led()
  The function lp5521_probe() references
  the function __init lp5521_init_led().
  This is often because lp5521_probe lacks a __init
  annotation or the annotation of lp5521_init_led is wrong.

Fixing this mismatch triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit d149e3b2 ("memcg: add the soft_limit reclaim in global direct
reclaim") adds a softlimit hook to shrink_zones().  By this, soft limit
is called as

   try_to_free_pages()
       do_try_to_free_pages()
           shrink_zones()
               mem_cgroup_soft_limit_reclaim()

Then, direct reclaim is memcg softlimit hint aware, now.

But, the memory cgroup's "limit" path can call softlimit shrinker.

   try_to_free_mem_cgroup_pages()
       do_try_to_free_pages()
           shrink_zones()
               mem_cgroup_soft_limit_reclaim()

This will cause a global reclaim when a memcg hits limit.

This is bug. soft_limit_reclaim() should be called when
scanning_global_lru(sc) == true.

And the commit adds a variable "total_scanned" for counting softlimit
scanned pages....it's not "total".  This patch removes the variable and
update sc->nr_scanned instead of it.  This will affect shrink_slab()'s
scan condition but, global LRU is scanned by softlimit and I think this
change makes sense.

TODO: avoid too much scanning of a zone when softlimit did enough work.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Ying Han <yinghan@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently a single process may register exit handlers unlimited times.
It may lead to a bloated listeners chain and very slow process
terminations.

Eg after 10KK sent TASKSTATS_CMD_ATTR_REGISTER_CPUMASKs ~300 Mb of
kernel memory is stolen for the handlers chain and "time id" shows 2-7
seconds instead of normal 0.003.  It makes it possible to exhaust all
kernel memory and to eat much of CPU time by triggerring numerous exits
on a single CPU.

The patch limits the number of times a single process may register
itself on a single CPU to one.

One little issue is kept unfixed - as taskstats_exit() is called before
exit_files() in do_exit(), the orphaned listener entry (if it was not
explicitly deregistered) is kept until the next someone's exit() and
implicit deregistration in send_cpu_listeners().  So, if a process
registered itself as a listener exits and the next spawned process gets
the same pid, it would inherit taskstats attributes.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Under heavy memory and filesystem load, users observe the assertion
mapping->nrpages == 0 in end_writeback() trigger.  This can be caused by
page reclaim reclaiming the last page from a mapping in the following
race:

	CPU0				CPU1
  ...
  shrink_page_list()
    __remove_mapping()
      __delete_from_page_cache()
        radix_tree_delete()
					evict_inode()
					  truncate_inode_pages()
					    truncate_inode_pages_range()
					      pagevec_lookup() - finds nothing
					  end_writeback()
					    mapping->nrpages != 0 -> BUG
        page->mapping = NULL
        mapping->nrpages--

Fix the problem by doing a reliable check of mapping->nrpages under
mapping->tree_lock in end_writeback().

Analyzed by Jay <jinshan.xiong@whamcloud.com>, lost in LKML, and dug out
by Miklos Szeredi <mszeredi@suse.de>.

Cc: Jay <jinshan.xiong@whamcloud.com>
Cc: Miklos Szeredi <mszeredi@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We cannot take a mutex while holding a spinlock, so flip the order and
fix the locking documentation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We observed the crash point count going negative in cases where the
crash point is hit multiple times before the check of "count == 0" is
done.  Because of this we never call lkdtm_do_action().  This patch just
adds a spinlock to protect count.
Reported-by: Tapan Dhimant <tdhimant@akamai.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: Ankita Garg <ankita@in.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is required for tilegx to be able to use the compat unistd.h header
where compat_sys_sendmmsg() is now mentioned.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

romfs_get_unmapped_area() checks argument `len' without considering
PAGE_ALIGN which will cause do_mmap_pgoff() return -EINVAL error after
commit f67d9b15 ("nommu: add page_align to mmap").

Fix the check by changing it in same way ramfs_nommu_get_unmapped_area()
was changed in ramfs/file-nommu.c.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

To make SLUB work on UML we need this_cpu_cmpxchg from
asm-generic/percpu.h.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

PT7C4338 chip is being manufactured by Pericom Technology Inc.  It is a
serial real-time clock which provides:

1) Low-power clock/calendar.
2) Programmable square-wave output.

It has 56 bytes of nonvolatile RAM.  Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Although it is used (by i915) on nothing but tmpfs, read_cache_page_gfp()
is unsuited to tmpfs, because it inserts a page into pagecache before
calling the filesystem's ->readpage: tmpfs may have pages in swapcache
which only it knows how to locate and switch to filecache.

At present tmpfs provides a ->readpage method, and copes with this by
copying pages; but soon we can simplify it by removing its ->readpage.
Provide shmem_read_mapping_page_gfp() now, ready for that transition,

Export shmem_read_mapping_page_gfp() and add it to list in shmem_fs.h,
with shmem_read_mapping_page() inline for the common mapping_gfp case.

(shmem_read_mapping_page_gfp or shmem_read_cache_page_gfp? Generally the
read_mapping_page functions use the mapping's ->readpage, and the
read_cache_page functions use the supplied filler, so I think
read_cache_page_gfp was slightly misnamed.)
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

2.6.35's new truncate convention gave tmpfs the opportunity to control
its file truncation, no longer enforced from outside by vmtruncate().
We shall want to build upon that, to handle pagecache and swap together.

Slightly redefine the ->truncate_range interface: let it now be called
between the unmap_mapping_range()s, with the filesystem responsible for
doing the truncate_inode_pages_range() from it - just as the filesystem
is nowadays responsible for doing that from its ->setattr.

Let's rename shmem_notify_change() to shmem_setattr().  Instead of
calling the generic truncate_setsize(), bring that code in so we can
call shmem_truncate_range() - which will later be updated to perform its
own variant of truncate_inode_pages_range().

Remove the punch_hole unmap_mapping_range() from shmem_truncate_range():
now that the COW's unmap_mapping_range() comes after ->truncate_range,
there is no need to call it a third time.

Export shmem_truncate_range() and add it to the list in shmem_fs.h, so
that i915_gem_object_truncate() can call it explicitly in future; get
this patch in first, then update drm/i915 once this is available (until
then, i915 will just be doing the truncate_inode_pages() twice).

Though introduced five years ago, no other filesystem is implementing
->truncate_range, and its only other user is madvise(,,MADV_REMOVE): we
expect to convert it to fallocate(,FALLOC_FL_PUNCH_HOLE,,) shortly,
whereupon ->truncate_range can be removed from inode_operations -
shmem_truncate_range() will help i915 across that transition too.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Before adding any more global entry points into shmem.c, gather such
prototypes into shmem_fs.h.  Remove mm's own declarations from swap.h,
but for now leave the ones in mm.h: because shmem_file_setup() and
shmem_zero_setup() are called from various places, and we should not
force other subsystems to update immediately.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

You would expect to find vmtruncate_range() next to vmtruncate() in
mm/truncate.c: move it there.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix 'make htmldocs' warnings:

  Warning(/include/linux/hrtimer.h:153): No description found for parameter 'clockid'
  Warning(/include/linux/device.h:604): Excess struct/union/enum/typedef member 'of_match' description in 'device'
  Warning(/include/net/sock.h:349): Excess struct/union/enum/typedef member 'sk_rmem_alloc' description in 'sock'
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: queue: bring discard_granularity/alignment into line with SCSI
  mmc: queue: append partition subname to queue thread name
  mmc: core: make erase timeout calculation allow for gated clock
  mmc: block: switch card to User Data Area when removing the block driver
  mmc: sdio: reset card during power_restore
  mmc: cb710: fix #ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
  mmc: sdhi: DMA slave ID 0 is invalid
  mmc: tmio: fix regression in TMIO_MMC_WRPROTECT_DISABLE handling
  mmc: omap_hsmmc: use original sg_len for dma_unmap_sg
  mmc: omap_hsmmc: fix ocr mask usage
  mmc: sdio: fix runtime PM path during driver removal
  mmc: Add PCI fixup quirks for Ricoh 1180:e823 reader
  mmc: sdhi: fix module unloading
  mmc: of_mmc_spi: add NO_IRQ define to of_mmc_spi.c
  mmc: vub300: fix null dereferences in error handling

commit 21a3c964 uses node_start/end_pfn(nid) for detection start/end
of nodes. But, it's not defined in linux/mmzone.h but defined in
/arch/???/include/mmzone.h which is included only under
CONFIG_NEED_MULTIPLE_NODES=y.

Then, we see
  mm/page_cgroup.c: In function 'page_cgroup_init':
  mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn'
  mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn'

So, fixiing page_cgroup.c is an idea...

But node_start_pfn()/node_end_pfn() is a very generic macro and
should be implemented in the same manner for all archs.
(m32r has different implementation...)

This patch removes definitions of node_start/end_pfn() in each archs
and defines a unified one in linux/mmzone.h. It's not under
CONFIG_NEED_MULTIPLE_NODES, now.

A result of macro expansion is here (mm/page_cgroup.c)

for !NUMA
 start_pfn = ((&contig_page_data)->node_start_pfn);
  end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});

for NUMA (x86-64)
  start_pfn = ((node_data[nid])->node_start_pfn);
  end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});

Changelog:
 - fixed to avoid using "nid" twice in node_end_pfn() macro.
Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  btrfs: fix inconsonant inode information
  Btrfs: make sure to update total_bitmaps when freeing cache V3
  Btrfs: fix type mismatch in find_free_extent()
  Btrfs: make sure to record the transid in new inodes

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: prevent bogus assert when trying to remove non-existent attribute
  xfs: clear XFS_IDIRTY_RELEASE on truncate down
  xfs: reset inode per-lifetime state when recycling it

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hid-multitouch: add support for a new Lumio dual-touch panel
  HID: hid-multitouch: correct VID for Stantum panels
  HID: hid-multitouch: ensure slots are initialized

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: pm: ensure ARMv7 CPUs save and restore the TLS register
  ARM: pm: proc-v7: fix missing struct processor pointers for suspend code
  ARM: 6969/1: plat-iop: fix build error
  ARM: 6961/1: zImage: Add build-time check for correctly-sized proc_type entries
  ARM: SMP: wait for CPU to be marked active
  ARM: 6963/1: Thumb-2: Relax relocation requirements for non-function symbols
  ARM: 6962/1: mach-h720x: fix build error
  ARM: 6959/1: SMP build fix for entry-macro-multi.S

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] allow setting of upper 32 bit in smp_ctl_set_bit
  [S390] hwsampler: Set a sane default sampling rate
  [S390] s390: enforce HW limits for the initial sampling rate
  [S390] kvm-s390: fix kconfig dependencies

When iputting the inode, We may leave the delayed nodes if they have some
delayed items that have not been dealt with. So when the inode is read again,
we must look up the relative delayed node, and use the information in it to
initialize the inode. Or we will get inconsonant inode information, it may
cause that the same directory index number is allocated again, and hit the
following oops:

[ 5447.554187] err add delayed dir index item(name: pglog_0.965_0) into the
insertion tree of the delayed node(root id: 262, inode id: 258, errno: -17)
[ 5447.569766] ------------[ cut here ]------------
[ 5447.575361] kernel BUG at fs/btrfs/delayed-inode.c:1301!
[SNIP]
[ 5447.790721] Call Trace:
[ 5447.793191]  [<ffffffffa0641c4e>] btrfs_insert_dir_item+0x189/0x1bb [btrfs]
[ 5447.800156]  [<ffffffffa0651a45>] btrfs_add_link+0x12b/0x191 [btrfs]
[ 5447.806517]  [<ffffffffa0651adc>] btrfs_add_nondir+0x31/0x58 [btrfs]
[ 5447.812876]  [<ffffffffa0651d6a>] btrfs_create+0xf9/0x197 [btrfs]
[ 5447.818961]  [<ffffffff8111f840>] vfs_create+0x72/0x92
[ 5447.824090]  [<ffffffff8111fa8c>] do_last+0x22c/0x40b
[ 5447.829133]  [<ffffffff8112076a>] path_openat+0xc0/0x2ef
[ 5447.834438]  [<ffffffff810c58e2>] ? __perf_event_task_sched_out+0x24/0x44
[ 5447.841216]  [<ffffffff8103ecdd>] ? perf_event_task_sched_out+0x59/0x67
[ 5447.847846]  [<ffffffff81121a79>] do_filp_open+0x3d/0x87
[ 5447.853156]  [<ffffffff811e126c>] ? strncpy_from_user+0x43/0x4d
[ 5447.859072]  [<ffffffff8111f1f5>] ? getname_flags+0x2e/0x80
[ 5447.864636]  [<ffffffff8111f179>] ? do_getname+0x14b/0x173
[ 5447.870112]  [<ffffffff8111f1b7>] ? audit_getname+0x16/0x26
[ 5447.875682]  [<ffffffff8112b1ab>] ? spin_lock+0xe/0x10
[ 5447.880882]  [<ffffffff81112d39>] do_sys_open+0x69/0xae
[ 5447.886153]  [<ffffffff81112db1>] sys_open+0x20/0x22
[ 5447.891114]  [<ffffffff813b9aab>] system_call_fastpath+0x16/0x1b

Fix it by reusing the old delayed node.
Reported-by: Jim Schutt <jaschut@sandia.gov>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Tested-by: Jim Schutt <jaschut@sandia.gov>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: mark CONFIG_CIFS_NFSD_EXPORT as BROKEN
  cifs: free blkcipher in smbhash

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  cifs: propagate errors from cifs_get_root() to mount(2)
  cifs: tidy cifs_do_mount() up a bit
  cifs: more breakage on mount failures
  cifs: close sget() races
  cifs: pull freeing mountdata/dropping nls/freeing cifs_sb into cifs_umount()
  cifs: move cifs_umount() call into ->kill_sb()
  cifs: pull cifs_mount() call up
  sanitize cifs_umount() prototype
  cifs: initialize ->tlink_tree in cifs_setup_cifs_sb()
  cifs: allocate mountdata earlier
  cifs: leak on mount if we share superblock
  cifs: don't pass superblock to cifs_mount()
  cifs: don't leak nls on mount failure
  cifs: double free on mount failure
  take bdi setup/destruction into cifs_mount/cifs_umount
Acked-by: Steve French <smfrench@gmail.com>

SCSI defines discard alignment as the offset to the first
optimal discard.  In the case of SD/MMC, that is always zero
which is the default.

SCSI defines discard granularity as a hint of a optimal
discard size.  That is much better expressed by the MMC
"preferred erase size" (pref_erase) field.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

For example, an eMMC with 2 boot partitions will have 3 threads.
The names change from:

   40 ?        00:00:00 mmcqd/0
   41 ?        00:00:00 mmcqd/0
   42 ?        00:00:00 mmcqd/0

to:

   40 ?        00:00:00 mmcqd/0
   41 ?        00:00:00 mmcqd/0boot0
   42 ?        00:00:00 mmcqd/0boot1
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The erase timeout calculation may depend on clock rate
which is zero if the clock is gated, so use
mmc_host_clk_rate() which allows for that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>