Received from Mark Salyzyn

Since the helper thread for the driver can be killed unceremoniously by
an application, we detect the loss of the helper and restart it.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Remove superfluous code, optimize code, harden code, cast code, correct
some text, use msleep instead of schedule_timeout_interruptible. No
bugs.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

If there are no aacraid controllers, we do not create the raid
controller chrdev, thus when the driver is unloaded it performs a
superfluous deregistration.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

The max_channel field is set one too large.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Some of the error return paths during initialization resulted in a zero
report to caller
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Plug and play actions resulting from event sequences shall time out if
they take longer than 30 seconds to complete.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

The loss of the ownership flags, despite their flaws, in the scsi
command were sorely missed and are reinstated more accurately in the
aacraid driver to track commands and permit us to properly handle error
recovery actions.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Clean up the remaining scsi id access methods, drop ID_LUN_TO_CONTAINER
macro.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

There is a window where we can be re-enabling an adapter, but
still allow SCSI commands to be sent to the target.  This fix
sets our window (request_limit) to -1 as soon as we know the
adapter is being reenabled, and closes a very teeny tiny
window where we could set the window back to 1 before we
grab a lock.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Doug found a bug where if scsi_execute_async fails, we are leaking
sg resources. scsi_do_req never failed so we did not have to handle
that case before.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

We currently have two implementations of this obsolete ioctl, one in
the block layer and one in the scsi code.  Both of them have drawbacks.

This patch kills the scsi layer version after updating the block version
with the missing bits:

 - argument checking
 - use scatterlist I/O
 - set number of retries based on the submitted command

This is the last user of non-S/G I/O except for the gdth driver, so
getting this in ASAP and through the scsi tree would be nie to kill
the non-S/G I/O path.  Jens, what do you think about adding a check
for non-S/G I/O in the midlayer?

Thanks to  Or Gerlitz for testing this patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

All participants agree that qla2xxx can now successfully replace this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mthca: Fix max_srq_sge returned by ib_query_device for Tavor devices
  IB/cache: Use correct pointer to calculate size
  IPoIB: Use spin_lock_irq() instead of spin_lock_irqsave()
  IPoIB: Close race in ipoib_flush_paths()
  IB/mthca: Disable tuning PCI read burst size
  IPoIB: Make send and receive queue sizes tunable
  IPoIB: Wait for join to finish before freeing mcast struct
  IB: simplify static rate encoding
  IPoIB: Consolidate private neighbour data handling
  IB/srp: Fix memory leak in options parsing
  IB/mthca: Always build debugging code unless CONFIG_EMBEDDED=y
  IPoIB: Always build debugging code unless CONFIG_EMBEDDED=y
  IB/mad: fix oops in cancel_mads

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] sata_mv: properly print HC registers

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [PATCH] Use pci_set_consistent_dma_mask in ixgb driver
  [PATCH] sky2: bad memory reference on dual port cards
  [PATCH] mv643xx_eth: Fix tx_timeout to only conditionally wake tx queue
  [PATCH] mv643xx_eth: Always free completed tx descs on tx interrupt
  [PATCH] net drivers: fix section attributes for gcc
  [PATCH] remove drivers/net/hydra.h
  [PATCH] drivers/net/via-rhine.c: make a function static
  [netdrvr b44] trim trailing whitespace
  [PATCH] b44: increase version to 1.00
  [PATCH] b44: disable default tx pause
  [PATCH] via-rhine: execute bounce buffers code on Rhine-I only
  [PATCH] network: axnet_cs.c: add missing 'PRIV' in ei_rx_overrun
  [PATCH] dlink pci cards using wrong driver

The ixgb driver is using pci_alloc_consistent, thus is should also use
pci_set_consistent_dma_mask.  This allows the driver to work on SGI
systems.

In case of an error during probing it should also disable the device again.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Sky2 driver will oops referencing bad memory if used on
a dual port card.  The problem is accessing past end of
MIB counter space.

Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

After resetting the hardware on a tx_timeout, call netif_wake_queue()
only if we have free tx descriptors.

Also, attempt to recover if mv643xx_eth_start_xmit() is called when
there are fewer free tx descriptors than expected.

The BUG_ON() call we are replacing was hit on a tx_timeout that
called netif_wake_queue(), indirectly via netif_device_attach(),
even though we did not have enough free tx descriptors.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix the tx interrupt handler to free completed tx descriptors even
when NAPI is enabled.  Otherwise, the tx queue would fill up resulting
in poor performance and "NETDEV WATCHDOG: <iface>: transmit timed out"
messages.
Signed-off-by: Brent Cook <bcook@bpointsys.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.

gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove drivers/net/hydra.h which is both unused and covered by a 4 clause
BSD licence (not by the UCB).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-By: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Currently it crashes when trying to dump the registers.  This is an obvious
one-liner fix I suppose.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

Disable default tx pause frame support.
The b44 controller has a bug that generates excessive tx pause
frames.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Patch suggested by Yang Wu (pin xue <pinxue@gmail.com>).
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch fixes the problem of some Dlink cards picking the wrong
driver.  It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).

If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).

This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [ISDN]: Static overruns in drivers/isdn/i4l/isdn_ppp.c
  [WAN]: Remove broken and unmaintained Sangoma drivers.
  [BRIDGE] ebtables: fix allocation in net/bridge/netfilter/ebtables.c
  [DCCP]: Fix leak in net/dccp/ipv4.c
  [BRIDGE]: receive link-local on disabled ports.
  [IPv6] reassembly: Always compute hash under the fragment lock.

Unregister the platform device again if the probe was unsuccessful.

This restores the behaviour of not loading the driver on probe() failure.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Continue with the next one on error from device registration.

This would seem the correct thing to do, even if it's not the probe()
error that we're getting.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Modules: PCM Midlevel

This patch makes the needlessly global snd_pcm_format_name() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Modules: AC97 Codec

Added the missing entry for VIA VT1618 codec.
No particular patch is needed, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Modules: HDA Codec driver

Add the model entry to support of ASUS U5A with AD1986A codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Modules: au88x0 driver

since idx is used as an index for vortex_pcm_prettyname[VORTEX_PCM_LAST],
it should not be equal to VORTEX_PCM_LAST. This fixes coverity bug id #572
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Modules: au88x0 driver

Removed all use of __devinit/__devexit and init.h from headers.  Any
attributes given in the prototype but not in the function definition have
been moved to the definition.

An exception is vortex_eq_free: I removed the __devexit attribute because
vortex_eq_free is called from vortex_core_shutdown, and
vortex_core_shutdown may be called from __devinit snd_vortex_create.

Compile tested with allyesconfig and allmodconfig.
Signed-off-by: Dale Sedivec <dale@codefu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Modules: HDA Codec driver

This patch adds the entry for the 5-stack pin-config for the STAC
chip on the Intel D945Pvs board with subdevice id 0x0707.

With this patch against 1.0.11rc4 in the linux kernel 2.6.17-rc1, I'm
able to successfully output over the optical port and analog ports.
Signed-off-by: Ashley Clark <aclark@ghoti.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>