This file contains routines and definitions specific to InfiniPath
devices that have PCI Express interfaces.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The ipath_ht400.c file contains routines and definitions specific to
HyperTransport-based InfiniPath devices.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

ipath_common.h and ips_common.h contain definitions shared between
userspace and the kernel.

ipath_kernel.h is the core driver header file.

ipath_debug.h contains mask values used for controlling driver debugging.

ipath_registers.h contains bitmask definitions used in chip registers.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The ipath driver is a low-level driver for PathScale InfiniPath host
channel adapters (HCAs) based on the HT-400 and PE-800 chips, including
the InfiniPath HT-460, the small form factor InfiniPath HT-460, the
InfiniPath HT-470 and the Linux Networx LS/X.

The ipath_driver.c file contains much of the low-level device handling
code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mad: RMPP support for additional classes
  IB/mad: include GID/class when matching receives
  IB/mthca: Fix section mismatch problems
  IPoIB: Fix oops with raw sockets
  IB/mthca: Fix check of size in SRQ creation
  IB/srp: Fix unmapping of fake scatterlist

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] sata_mv: three bug fixes
  [PATCH] libata: ata_dev_init_params() fixes
  [PATCH] libata: Fix interesting use of "extern" and also some bracketing
  [PATCH] libata: Simplex and other mode filtering logic
  [PATCH] libata - ATA is both ATA and CFA
  [PATCH] libata: Add ->set_mode hook for odd drivers
  [PATCH] libata: BMDMA handling updates
  [PATCH] libata: kill trailing whitespace
  [PATCH] libata: add FIXME above ata_dev_xfermask()
  [PATCH] libata: cosmetic changes in ata_bus_softreset()
  [PATCH] libata: kill E.D.D.

* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: remove drm_{alloc,free}_pages
  drm: sis fix compile warning
  drm: add new radeon PCI ids..
  drm: read breadcrumb in IRQ handler
  drm: fixup i915 breadcrumb read/write
  drm:  remove pointless checks in radeon_state
  drm: fixup improper cast.
  drm: rationalise some pci ids
  drm: Add general-purpose packet for manipulating scratch registers (r300)
  drm: rework radeon memory map (radeon 1.23)
  drm: update r300 register names
  drm: fixup PCI DMA support

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] ioremap() should prefer WB over UC
  [IA64] Add __mca_table to the DISCARD list in gate.lds
  [IA64] Move __mca_table out of the __init section
  [IA64] simplify some condition checks in iosapic_check_gsi_range
  [IA64] correct some messages and fixes some minor things
  [IA64-SGI] fix for-loop in sn_hwperf_geoid_to_cnode()
  [IA64-SGI] sn_hwperf use of num_online_cpus()
  [IA64] optimize flush_tlb_range on large numa box
  [IA64] lazy_mmu_prot_update needs to be aware of huge pages

This enables the caller to migrate pages from one address space page
cache to another.  In buzz word marketing, you can do zero-copy file
copies!
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).

From the splice.c comments:

   "splice": joining two ropes together by interweaving their strands.

   This is the "extended pipe" functionality, where a pipe is used as
   an arbitrary in-memory buffer. Think of a pipe as a small kernel
   buffer that you can use to transfer data from one end to the other.

   The traditional unix read/write is extended with a "splice()" operation
   that transfers data buffers to or from a pipe buffer.

   Named by Larry McVoy, original implementation from Linus, extended by
   Jens to support splicing to files and fixing the initial implementation
   bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

efi_memmap_init() collects full granules of WB memory, without
regard for whether they also support UC.  So in order for ioremap()
to work for main memory, it must prefer WB mappings when possible.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Add __mca_table to the DISCARD list for the gate.lds linker script to
avoid broken linker references when linking the final vmlinux file.

Also add comment to include/asm-ia64/asmmacros.h to avoid anyone else
hitting this problem in the future.

Credits to James Bottomley <James.Bottomley@SteelEye.com> for spotting
the DISCARD list in gate.lds.S
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Add RMPP support for additional management classes that support it.
Also, validate RMPP is consistent with management class specified.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Received responses are currently matched against sent requests based
on TID only.  According to the spec, responses should match based on
the combination of TID, management class, and requester LID/GID.

Without the additional qualification, an agent that is responding to
two requests, both of which have the same TID, can match RMPP ACKs
with the incorrect transaction.  This problem can occur on the SM node
when responding to SA queries.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Conflicts:

	drivers/scsi/sata_mv.c

(1) A DMA transfer size of 0x10000 was not being written
as 0x0000 in the PRDs.  Fixed.

(1) The DEV_IRQ interrupt cause bit happens spuriously
during EDMA operation, and was not being ignored by the driver.
This led to various "drive busy" errors being reported,
with associated unpredictable behaviour.  Fixed.

(2) If a SATA or PCI interrupt was received with no outstanding
command, the interrupt handler still attempted to invoke
ata_qc_complete(), triggering assert()/BUG_ON() behaviour
elsewhere in libata.  Fixed.

The driver still has issues with confusion after error-recovery,
but should now  be reliable in the absence of drive errors.
I will be looking more into the error-handling bugs next.
Signed-Off-By: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ata_dev_init_params() fixes:
- Get the "heads" and "sectors" parameters from caller instead of implicitly from dev->id[].
- Return AC_ERR_INVALID instead of 0 if an invalid parameter is found
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>

Last of the set, just clean up some oddments. Assuming the whole set is
now ok then the remaining differences are the setup of PIO_0 at reset
and the ->data_xfer method.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core

This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.

Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

I think this is still needed with the new probe code (which btw seems to
be missing docs in upstream ?).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This is the minimal patch set to enable the current code to be used with
a controller following SFF (ie any PATA and early SATA controllers)
safely without crashes if there is no BMDMA area or if BMDMA is not
assigned by the BIOS for some reason.

Simplex status is recorded but not acted upon in this change, this isn't
a problem with the current drivers as none of them are for simplex
hardware. A following diff will deal with that.

The flags in the probe structure remain ->host_set_flags although Jeff
asked me to rename them, simply because the rename would break the usual
Linux rules that old code should break when there are changes. not
compile and run and then blow up/eat your computer/etc. Renaming this
later is a trivial exercise once a better name is chosen.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

gcc4 doesn't like us declaring a static function inside another
function.  We can do away with this construct altogether and use
BUILD_BUG_ON() instead (idea from Andi Kleen.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Added code to check for invalid MAC address from eeprom or user input.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The comments concerning how the pcnet32 ethernet device driver selects
the MAC addr to use are incorrect. A recent patch (in the last 3 months)
changed how the code worked, but did not change the comments.

Side comment: the new behaviour is good; I've got a pcnet32 card which
powers up with garbage in the CSR's, and a good MAC addr in the PROM.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Don't bother testing for CONFIG_NET_CBUS ("NEC PC-9800 C-bus cards"); it went
out with the rest of PC98 subarch.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The natsemi chip can have a larger EEPROM attached than it itself uses for
configuration.  This patch adds support for user space access to such an
EEPROM.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This enables TX checksum offloading for the spidernet driver by default.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	Add support for the bonding master to specify its carrier state
based upon the state of the slaves.  For 802.3ad, the bond is up if
there is an active, parterned aggregator.  For other modes, the bond is
up if any slaves are up.  Updates driver version to 3.0.3.

	Based on a patch by jamal <hadi@cyberus.ca>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix section mismatches in acenic driver:
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwText from .text between 'acenic_probe_one' (at offset 0x2409) and 'ace_interrupt'
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwRodata from .text between 'acenic_probe_one' (at offset 0x2422) and 'ace_interrupt'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch reduces the message level of the RX ram full messages
from err to debug to prevent spamming the console leaving it in the
logfiles though.

From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Problems with link state detection have been reported several times in the
past months.

Denis Vlasenko did all the work tracking it down. Jeff Garzik suggested the
proper place for the fix.

When using the mii library, the driver needs to check mii->force_media
and set dev->state accordingly.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

Kill trailing whitespace.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Initializing the b44 MAC & PCI functional blocks in the controller must
occur inside init_one(). This will allow access to the MAC registers.
The controller was being powered up in b44_open() which would not allow
access to the registers before ifconfig was up.
Philip Kohlbecher found this bug.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NETFILTER]: Rename init functions.
  [TCP]: Fix RFC2465 typo.
  [INET]: Introduce tunnel4/tunnel6
  [NET]: deinline 200+ byte inlines in sock.h
  [ECONET]: Convert away from SOCKOPS_WRAPPED
  [NET]: Fix ipx/econet/appletalk/irda ioctl crashes
  [NET]: Kill Documentation/networking/TODO
  [TG3]: Update version and reldate
  [TG3]: Skip timer code during full lock
  [TG3]: Speed up SRAM access
  [TG3]: Fix PHY loopback on 5700
  [TG3]: Fix bug in 40-bit DMA workaround code
  [TG3]: Fix probe failure due to invalid MAC address

* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (67 commits)
  [PATCH] powerpc: Remove oprofile spinlock backtrace code
  [PATCH] powerpc: Add oprofile calltrace support to all powerpc cpus
  [PATCH] powerpc: Add oprofile calltrace support
  [PATCH] for_each_possible_cpu: ppc
  [PATCH] for_each_possible_cpu: powerpc
  [PATCH] lock PTE before updating it in 440/BookE page fault handler
  [PATCH] powerpc: Kill _machine and hard-coded platform numbers
  ppc: Fix compile error in arch/ppc/lib/strcase.c
  [PATCH] git-powerpc: WARN was a dumb idea
  [PATCH] powerpc: a couple of trivial compile warning fixes
  powerpc: remove OCP references
  powerpc: Make uImage default build output for MPC8540 ADS
  powerpc: move math-emu over to arch/powerpc
  powerpc: use memparse() for mem= command line parsing
  ppc: fix strncasecmp prototype
  [PATCH] powerpc: make ISA floppies work again
  [PATCH] powerpc: Fix some initcall return values
  [PATCH] powerpc: Workaround for pSeries RTAS bug
  [PATCH] spufs: fix __init/__exit annotations
  [PATCH] powerpc: add hvc backend for rtas
  ...

Move __mca_table out of the __init section.
Signed-off-by: Tony Luck <tony.luck@intel.com>