It's been observed that driver's power state goes out
of sync with firmware in some corner cases. When this
happens, driver tries to download the data to firmware
assuming it's awake which causes Tx data timeout.

Main thread will process interrupt as soon as interrupt
handler fills 'int_status' variable.

This patch fixes the race issue by updating 'int_status'
at the end of mwifiex_interrupt_status().
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Newer pcie chipsets (8997 onwards) support MSIx. This
patch enables it.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore_read/wlcore_write can return negative values so it should
be assigned to signed variable.

The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2120705

Fixes: 3719c17e ("wlcore/wl18xx: fw logger over sdio")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add 'verext' debugfs item, which can be used to
get detailed chip specific information from our firmware.

Examples:
echo "1" > /sys/kernel/debug/mwifiex/mlan0/verext
cat /sys/kernel/debug/mwifiex/mlan0/verext
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The port_open flag is not applicable for IBSS mode. IBSS data
path was broken when port_open flag was introduced.
This patch fixes the problem by correcting the checks.

Fixes: 5c894633 ("mwifiex: enable traffic only when port is open")
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Same chip is being used by WLAN as well as bluetooth
drivers. Each driver needs to check during initialisation
if firmware is already active or it needs to be freshly
downloaded. If one driver has started downloading the
firmware, other finds the winner flag as false.

mwifiex_check_fw_status() checks firmware status and also
check if WLAN is the winner for firmware downloading.

Once we detect that other interface is downloading
the firmware, we call this routine again with max
poll count to wait until firmware is ready.

This patch splits the routine to avoid checking
winner status unnecessarily multiple times and ensures
that correct messages are displayed to user.

Firmware status poll count is also increased to 150.
Signed-off-by: Chunfan Chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add DT support for the wl1271 SPI WiFi.

Add documentation file for the wl1271 SPI WiFi.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The power function uses a consumer regulator access to update the WiFi
enable GPIO value.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Pull networking fixes from David Miller:
 "A quick set of bug fixes after there initial networking merge:

  1) Netlink multicast group storage allocator only was tested with
     nr_groups equal to 1, make it work for other values too.  From
     Matti Vaittinen.

  2) Check build_skb() return value in macb and hip04_eth drivers, from
     Weidong Wang.

  3) Don't leak x25_asy on x25_asy_open() failure.

  4) More DMA map/unmap fixes in 3c59x from Neil Horman.

  5) Don't clobber IP skb control block during GSO segmentation, from
     Konstantin Khlebnikov.

  6) ECN helpers for ipv6 don't fixup the checksum, from Eric Dumazet.

  7) Fix SKB segment utilization estimation in xen-netback, from David
     Vrabel.

  8) Fix lockdep splat in bridge addrlist handling, from Nikolay
     Aleksandrov"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
  bgmac: Fix reversed test of build_skb() return value.
  bridge: fix lockdep addr_list_lock false positive splat
  net: smsc: Add support h8300
  xen-netback: free queues after freeing the net device
  xen-netback: delete NAPI instance when queue fails to initialize
  xen-netback: use skb to determine number of required guest Rx requests
  net: sctp: Move sequence start handling into sctp_transport_get_idx()
  ipv6: update skb->csum when CE mark is propagated
  net: phy: turn carrier off on phy attach
  net: macb: clear interrupts when disabling them
  sctp: support to lookup with ep+paddr in transport rhashtable
  net: hns: fixes no syscon error when init mdio
  dts: hisi: fixes no syscon fault when init mdio
  net: preserve IP control block during GSO segmentation
  fsl/fman: Delete one function call "put_device" in dtsec_config()
  hip04_eth: fix missing error handle for build_skb failed
  3c59x: fix another page map/single unmap imbalance
  3c59x: balance page maps and unmaps
  x25_asy: Free x25_asy on x25_asy_open() failure.
  mlxsw: fix SWITCHDEV_OBJ_ID_PORT_MDB
  ...

Pull sparc fixes from David Miller:
 "Two sparc bug fixes"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix numa node distance initialization
  sparc64: fix incorrect sign extension in sys_sparc64_personality

Pull powerpc updates from Michael Ellerman:
 "Core:
   - Ground work for the new Power9 MMU from Aneesh Kumar K.V
   - Optimise FP/VMX/VSX context switching from Anton Blanchard

  Misc:
   - Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
     Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
     Andrew Donnellan
   - Allow wrapper to work on non-english system from Laurent Vivier
   - Add rN aliases to the pt_regs_offset table from Rashmica Gupta
   - Fix module autoload for rackmeter & axonram drivers from Luis de
     Bethencourt
   - Include KVM guest test in all interrupt vectors from Paul Mackerras
   - Fix DSCR inheritance over fork() from Anton Blanchard
   - Make value-returning atomics & {cmp}xchg* & their atomic_ versions
     fully ordered from Boqun Feng
   - Print MSR TM bits in oops messages from Michael Neuling
   - Add TM signal return & invalid stack selftests from Michael Neuling
   - Limit EPOW reset event warnings from Vipin K Parashar
   - Remove the Cell QPACE code from Rashmica Gupta
   - Append linux_banner to exception information in xmon from Rashmica
     Gupta
   - Add selftest to check if VSRs are corrupted from Rashmica Gupta
   - Remove broken GregorianDay() from Daniel Axtens
   - Import Anton's context_switch2 benchmark into selftests from
     Michael Ellerman
   - Add selftest script to test HMI functionality from Daniel Axtens
   - Remove obsolete OPAL v2 support from Stewart Smith
   - Make enter_rtas() private from Michael Ellerman
   - PPR exception cleanups from Michael Ellerman
   - Add page soft dirty tracking from Laurent Dufour
   - Add support for Nvlink NPUs from Alistair Popple
   - Add support for kexec on 476fpe from Alistair Popple
   - Enable kernel CPU dlpar from sysfs from Nathan Fontenot
   - Copy only required pieces of the mm_context_t to the paca from
     Michael Neuling
   - Add a kmsg_dumper that flushes OPAL console output on panic from
     Russell Currey
   - Implement save_stack_trace_regs() to enable kprobe stack tracing
     from Steven Rostedt
   - Add HWCAP bits for Power9 from Michael Ellerman
   - Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
   - Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
   - scripts/recordmcount.pl: support data in text section on powerpc
     from Ulrich Weigand
   - Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand

  cxl:
   - cxl: Fix possible idr warning when contexts are released from
     Vaibhav Jain
   - cxl: use correct operator when writing pcie config space values
     from Andrew Donnellan
   - cxl: Fix DSI misses when the context owning task exits from Vaibhav
     Jain
   - cxl: fix build for GCC 4.6.x from Brian Norris
   - cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
   - cxl: Enable PCI device ID for future IBM CXL adapter from Uma
     Krishnan

  Freescale:
   - Freescale updates from Scott: Highlights include moving QE code out
     of arch/powerpc (to be shared with arm), device tree updates, and
     minor fixes"

* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
  powerpc/module: Handle R_PPC64_ENTRY relocations
  scripts/recordmcount.pl: support data in text section on powerpc
  powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
  powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
  powerpc/mm: Fix _PAGE_PTE breaking swapoff
  cxl: Enable PCI device ID for future IBM CXL adapter
  cxl: use -Werror only with CONFIG_PPC_WERROR
  cxl: fix build for GCC 4.6.x
  powerpc: Add HWCAP bits for Power9
  powerpc/powernv: Reserve PE#0 on NPU
  powerpc/powernv: Change NPU PE# assignment
  powerpc/powernv: Fix update of NVLink DMA mask
  powerpc/powernv: Remove misleading comment in pci.c
  powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
  powerpc: Fix build break due to paca mm_context_t changes
  cxl: Fix DSI misses when the context owning task exits
  MAINTAINERS: Update Scott Wood's e-mail address
  powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
  powerpc: Fix style of self-test config prompts
  powerpc/powernv: Only delay opal_rtc_read() retry when necessary
  ...

Fixes: f1640c3d ("bgmac: fix a missing check for build_skb")
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull VFIO updates from Alex Williamson:

 - Fixes in AMD xgbe reset, spapr structure padding, type 1 flags (Dan
   Carpenter, Alexey Kardashevskiy, Pierre Morel)

 - Re-introduce no-iommu mode, with a user this time (Alex Williamson)

* tag 'vfio-v4.5-rc1' of git://github.com/awilliam/linux-vfio:
  vfio/iommu_type1: make use of info.flags
  vfio: Include No-IOMMU mode
  vfio: Add explicit alignments in vfio_iommu_spapr_tce_create
  VFIO: platform: reset: fix a warning message condition

Pull nfsd updates from Bruce Fields:
 "Smaller bugfixes and cleanup, including a fix for a failures of
  kerberized NFSv4.1 mounts, and Scott Mayhew's work addressing ACK
  storms that can affect some high-availability NFS setups"

* tag 'nfsd-4.5' of git://linux-nfs.org/~bfields/linux:
  nfsd: add new io class tracepoint
  nfsd: give up on CB_LAYOUTRECALLs after two lease periods
  nfsd: Fix nfsd leaks sunrpc module references
  lockd: constify nlmsvc_binding structure
  lockd: use to_delayed_work
  nfsd: use to_delayed_work
  Revert "svcrdma: Do not send XDR roundup bytes for a write chunk"
  lockd: Register callbacks on the inetaddr_chain and inet6addr_chain
  nfsd: Register callbacks on the inetaddr_chain and inet6addr_chain
  sunrpc: Add a function to close temporary transports immediately
  nfsd: don't base cl_cb_status on stale information
  nfsd4: fix gss-proxy 4.1 mounts for some AD principals
  nfsd: fix unlikely NULL deref in mach_creds_match
  nfsd: minor consolidation of mach_cred handling code
  nfsd: helper for dup of possibly NULL string
  svcrpc: move some initialization to common code
  nfsd: fix a warning message
  nfsd: constify nfsd4_callback_ops structure
  nfsd: recover: constify nfsd4_client_tracking_ops structures
  svcrdma: Do not send XDR roundup bytes for a write chunk

Pull vfs regression fix from Al Viro:
 "Fix for braino introduced in vfs.git#work.misc"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  amdkfd: Copy from the proper user command pointer

After promisc mode management was introduced a bridge device could do
dev_set_promiscuity from its ndo_change_rx_flags() callback which in
turn can be called after the bridge's addr_list_lock has been taken
(e.g. by dev_uc_add). This causes a false positive lockdep splat because
the port interfaces' addr_list_lock is taken when br_manage_promisc()
runs after the bridge's addr list lock was already taken.
To remove the false positive introduce a custom bridge addr_list_lock
class and set it on bridge init.
A simple way to reproduce this is with the following:
$ brctl addbr br0
$ ip l add l br0 br0.100 type vlan id 100
$ ip l set br0 up
$ ip l set br0.100 up
$ echo 1 > /sys/class/net/br0/bridge/vlan_filtering
$ brctl addif br0 eth0
Splat:
[   43.684325] =============================================
[   43.684485] [ INFO: possible recursive locking detected ]
[   43.684636] 4.4.0-rc8+ #54 Not tainted
[   43.684755] ---------------------------------------------
[   43.684906] brctl/1187 is trying to acquire lock:
[   43.685047]  (_xmit_ETHER){+.....}, at: [<ffffffff8150169e>] dev_set_rx_mode+0x1e/0x40
[   43.685460]  but task is already holding lock:
[   43.685618]  (_xmit_ETHER){+.....}, at: [<ffffffff815072a7>] dev_uc_add+0x27/0x80
[   43.686015]  other info that might help us debug this:
[   43.686316]  Possible unsafe locking scenario:

[   43.686743]        CPU0
[   43.686967]        ----
[   43.687197]   lock(_xmit_ETHER);
[   43.687544]   lock(_xmit_ETHER);
[   43.687886] *** DEADLOCK ***

[   43.688438]  May be due to missing lock nesting notation

[   43.688882] 2 locks held by brctl/1187:
[   43.689134]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81510317>] rtnl_lock+0x17/0x20
[   43.689852]  #1:  (_xmit_ETHER){+.....}, at: [<ffffffff815072a7>] dev_uc_add+0x27/0x80
[   43.690575] stack backtrace:
[   43.690970] CPU: 0 PID: 1187 Comm: brctl Not tainted 4.4.0-rc8+ #54
[   43.691270] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014
[   43.691770]  ffffffff826a25c0 ffff8800369fb8e0 ffffffff81360ceb ffffffff826a25c0
[   43.692425]  ffff8800369fb9b8 ffffffff810d0466 ffff8800369fb968 ffffffff81537139
[   43.693071]  ffff88003a08c880 0000000000000000 00000000ffffffff 0000000002080020
[   43.693709] Call Trace:
[   43.693931]  [<ffffffff81360ceb>] dump_stack+0x4b/0x70
[   43.694199]  [<ffffffff810d0466>] __lock_acquire+0x1e46/0x1e90
[   43.694483]  [<ffffffff81537139>] ? netlink_broadcast_filtered+0x139/0x3e0
[   43.694789]  [<ffffffff8153b5da>] ? nlmsg_notify+0x5a/0xc0
[   43.695064]  [<ffffffff810d10f5>] lock_acquire+0xe5/0x1f0
[   43.695340]  [<ffffffff8150169e>] ? dev_set_rx_mode+0x1e/0x40
[   43.695623]  [<ffffffff815edea5>] _raw_spin_lock_bh+0x45/0x80
[   43.695901]  [<ffffffff8150169e>] ? dev_set_rx_mode+0x1e/0x40
[   43.696180]  [<ffffffff8150169e>] dev_set_rx_mode+0x1e/0x40
[   43.696460]  [<ffffffff8150189c>] dev_set_promiscuity+0x3c/0x50
[   43.696750]  [<ffffffffa0586845>] br_port_set_promisc+0x25/0x50 [bridge]
[   43.697052]  [<ffffffffa05869aa>] br_manage_promisc+0x8a/0xe0 [bridge]
[   43.697348]  [<ffffffffa05826ee>] br_dev_change_rx_flags+0x1e/0x20 [bridge]
[   43.697655]  [<ffffffff81501532>] __dev_set_promiscuity+0x132/0x1f0
[   43.697943]  [<ffffffff81501672>] __dev_set_rx_mode+0x82/0x90
[   43.698223]  [<ffffffff815072de>] dev_uc_add+0x5e/0x80
[   43.698498]  [<ffffffffa05b3c62>] vlan_device_event+0x542/0x650 [8021q]
[   43.698798]  [<ffffffff8109886d>] notifier_call_chain+0x5d/0x80
[   43.699083]  [<ffffffff810988b6>] raw_notifier_call_chain+0x16/0x20
[   43.699374]  [<ffffffff814f456e>] call_netdevice_notifiers_info+0x6e/0x80
[   43.699678]  [<ffffffff814f4596>] call_netdevice_notifiers+0x16/0x20
[   43.699973]  [<ffffffffa05872be>] br_add_if+0x47e/0x4c0 [bridge]
[   43.700259]  [<ffffffffa058801e>] add_del_if+0x6e/0x80 [bridge]
[   43.700548]  [<ffffffffa0588b5f>] br_dev_ioctl+0xaf/0xc0 [bridge]
[   43.700836]  [<ffffffff8151a7ac>] dev_ifsioc+0x30c/0x3c0
[   43.701106]  [<ffffffff8151aac9>] dev_ioctl+0xf9/0x6f0
[   43.701379]  [<ffffffff81254345>] ? mntput_no_expire+0x5/0x450
[   43.701665]  [<ffffffff812543ee>] ? mntput_no_expire+0xae/0x450
[   43.701947]  [<ffffffff814d7b02>] sock_do_ioctl+0x42/0x50
[   43.702219]  [<ffffffff814d8175>] sock_ioctl+0x1e5/0x290
[   43.702500]  [<ffffffff81242d0b>] do_vfs_ioctl+0x2cb/0x5c0
[   43.702771]  [<ffffffff81243079>] SyS_ioctl+0x79/0x90
[   43.703033]  [<ffffffff815eebb6>] entry_SYSCALL_64_fastpath+0x16/0x7a

CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Bridge list <bridge@lists.linux-foundation.org>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Fixes: 2796d0c6 ("bridge: Automatically manage port promiscuous mode.")
Reported-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull md updates from Neil Brown:
 "Mostly clustered-raid1 and raid5 journal updates.  one Y2038 fix and
  other minor stuff.

  One patch removes me from the MAINTAINERS file and adds a record of my
  md maintainership to Credits"

Many thanks to Neil, who has been around for a _looong_ time.

* tag 'md/4.5' of git://neil.brown.name/md: (26 commits)
  md/raid: only permit hot-add of compatible integrity profiles
  Remove myself as MD Maintainer, and add to Credits.
  raid5-cache: handle journal hotadd in quiesce
  MD: add journal with array suspended
  md: set MD_HAS_JOURNAL in correct places
  md: Remove 'ready' field from mddev.
  md: remove unnecesary md_new_event_inintr
  raid5: allow r5l_io_unit allocations to fail
  raid5-cache: use a mempool for the metadata block
  raid5-cache: use a bio_set
  raid5-cache: add journal hot add/remove support
  drivers: md: use ktime_get_real_seconds()
  md: avoid warning for 32-bit sector_t
  raid5-cache: free meta_page earlier
  raid5-cache: simplify r5l_move_io_unit_list
  md: update comment for md_allow_write
  md-cluster: update comments for MD_CLUSTER_SEND_LOCKED_ALREADY
  md-cluster: Protect communication with mutexes
  md-cluster: Defer MD reloading to mddev->thread
  md-cluster: update the documentation
  ...

Pull regulator updates from Mark Brown:
 "Aside from a fix for a spurious warning (which caused more problems
  than it fixed in the fixing really) this is all driver updates,
  including new drivers for Dialog PV88060/90 and TI LM363x and TPS65086
  devices.  The qcom_smd driver has had PM8916 and PMA8084 support
  added"

* tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
  regulator: core: remove some dead code
  regulator: core: use dev_to_rdev
  regulator: lp872x: Get rid of duplicate reference to DVS GPIO
  regulator: lp872x: Add missing of_match in regulators descriptions
  regulator: axp20x: Fix GPIO LDO enable value for AXP22x
  regulator: lp8788: constify regulator_ops structures
  regulator: wm8*: constify regulator_ops structures
  regulator: da9*: constify regulator_ops structures
  regulator: mt6311: Use REGCACHE_RBTREE
  regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability
  regulator: qcom-smd: Add support for PMA8084
  regulator: qcom-smd: Add PM8916 support
  soc: qcom: documentation: Update SMD/RPM Docs
  regulator: pv88090: logical vs bitwise AND typo
  regulator: pv88090: Fix irq leak
  regulator: pv88090: new regulator driver
  regulator: wm831x-ldo: Use platform_register/unregister_drivers()
  regulator: wm831x-dcdc: Use platform_register/unregister_drivers()
  regulator: lp8788-ldo: Use platform_register/unregister_drivers()
  regulator: core: Fix nested locking of supplies
  ...

Add H8/300 platform support for smc91x
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

8f1d57c1 ("amdkfd: don't open-code memdup_user()") mistakenly uses
an uninitialized local pointer, gcc complains:

  drivers/gpu/drm/amd/amdkfd/kfd_chardev.c: In function ‘kfd_ioctl_dbg_address_watch’:
  drivers/gpu/drm/amd/amdkfd/kfd_chardev.c:562:12: warning: ‘args_buff’ may be used uninitialized in this function [-Wmaybe-uninitialized]
    args_buff = memdup_user(args_buff,
                ^

Fix it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull mailbox fixlet from Jussi Brar.

* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: constify mbox_chan_ops structure

David Vrabel says:

====================
xen-netback: use skb to determine number of required (etc.)

"xen-netback: use skb to determine number of required" plus two other
minor fixes I found down the back of the sofa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If a queue still has a NAPI instance added to the net device, freeing
the queues early results in a use-after-free.

The shouldn't ever happen because we disconnect and tear down all queues
before freeing the net device, but doing this makes it obviously safe.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When xenvif_connect() fails it may leave a stale NAPI instance added to
the device.  Make sure we delete it in the error path.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using the MTU or GSO size to determine the number of required guest Rx
requests for an skb was subtly broken since these value may change at
runtime.

After 1650d545 (xen-netback: always
fully coalesce guest Rx packets) we always fully pack a packet into
its guest Rx slots.  Calculating the number of required slots from the
packet length is then easy.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sctp/proc.c: In function ‘sctp_transport_get_idx’:
net/sctp/proc.c:313: warning: ‘obj’ may be used uninitialized in this function

This is currently a false positive, as all callers check for a zero
offset first, and handle this case in the exact same way.

Move the check and handling into sctp_transport_get_idx() to kill the
compiler warning, and avoid future bugs.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a tunnel decapsulates the outer header, it has to comply
with RFC 6080 and eventually propagate CE mark into inner header.

It turns out IP6_ECN_set_ce() does not correctly update skb->csum
for CHECKSUM_COMPLETE packets, triggering infamous "hw csum failure"
messages and stack traces.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull UDF fixes and quota cleanups from Jan Kara:
 "Several UDF fixes and some minor quota cleanups"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Check output buffer length when converting name to CS0
  udf: Prevent buffer overrun with multi-byte characters
  quota: constify qtree_fmt_operations structures
  udf: avoid uninitialized variable use
  udf: Fix lost indirect extent block
  udf: Factor out code for creating indirect extent
  udf: limit the maximum number of indirect extents in a row
  udf: limit the maximum number of TD redirections
  fs: make quota/dquot.c explicitly non-modular
  fs: make quota/netlink.c explicitly non-modular

The operstate of a networking device initially IF_OPER_UNKNOWN aka
"unknown", updated on carrier state changes (with carrier state being on
by default). This means it will stay unknown unless the carrier state
goes to off at some point, which is not the case if the phy is already
up/connected at startup.

Explicitly turn off the carrier on phy attach, leaving the phy state
machine to turn the carrier on when it has done the initial negotiation.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disabling interrupts with the IDR register does not stop the macb hardware
from asserting its interrupt line if there are interrupts pending.  Always
clear the interrupts using ISR, and be sure to write it on hardware that
is not read-to-clear, like Zynq.  Not doing so will cause interrupts when
the driver doesn't expect them.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge first patch-bomb from Andrew Morton:

 - A few hotfixes which missed 4.4 becasue I was asleep.  cc'ed to
   -stable

 - A few misc fixes

 - OCFS2 updates

 - Part of MM.  Including pretty large changes to page-flags handling
   and to thp management which have been buffered up for 2-3 cycles now.

  I have a lot of MM material this time.

[ It turns out the THP part wasn't quite ready, so that got dropped from
  this series  - Linus ]

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
  zsmalloc: reorganize struct size_class to pack 4 bytes hole
  mm/zbud.c: use list_last_entry() instead of list_tail_entry()
  zram/zcomp: do not zero out zcomp private pages
  zram: pass gfp from zcomp frontend to backend
  zram: try vmalloc() after kmalloc()
  zram/zcomp: use GFP_NOIO to allocate streams
  mm: add tracepoint for scanning pages
  drivers/base/memory.c: fix kernel warning during memory hotplug on ppc64
  mm/page_isolation: use macro to judge the alignment
  mm: fix noisy sparse warning in LIBCFS_ALLOC_PRE()
  mm: rework virtual memory accounting
  include/linux/memblock.h: fix ordering of 'flags' argument in comments
  mm: move lru_to_page to mm_inline.h
  Documentation/filesystems: describe the shared memory usage/accounting
  memory-hotplug: don't BUG() in register_memory_resource()
  hugetlb: make mm and fs code explicitly non-modular
  mm/swapfile.c: use list_for_each_entry_safe in free_swap_count_continuations
  mm: /proc/pid/clear_refs: no need to clear VM_SOFTDIRTY in clear_soft_dirty_pmd()
  mm: make sure isolate_lru_page() is never called for tail page
  vmstat: make vmstat_updater deferrable again and shut down on idle
  ...

Now, when we sendmsg, we translate the ep to laddr by selecting the
first element of the list, and then do a lookup for a transport.

But sctp_hash_cmp() will compare it against asoc addr_list, which may
be a subset of ep addr_list, meaning that this chosen laddr may not be
there, and thus making it impossible to find the transport.

So we fix it by using ep + paddr to lookup transports in hashtable. In
sctp_hash_cmp, if .ep is set, we will check if this ep == asoc->ep,
or we will do the laddr check.

Fixes: d6c0256a ("sctp: add the rhashtable apis for sctp global transport hashtable")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reported-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reoder the pages_per_zspage field in struct size_class which can
eliminate the 4 bytes hole between it and stats field.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

list_last_entry*( has been defined in list.h, so replace
list_tail_entry() with it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Do not __GFP_ZERO allocated zcomp ->private pages.  We keep allocated
streams around and use them for read/write requests, so we supply a
zeroed out ->private to compression algorithm as a scratch buffer only
once -- the first time we use that stream.  For the rest of IO requests
served by this stream ->private usually contains some temporarily data
from the previous requests.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Each zcomp backend uses own gfp flag but it's pointless because the
context they could be called is driven by upper layer(ie, zcomp
frontend).  As well, zcomp frondend could call them in different
context.  One context(ie, zram init part) is it should be better to make
sure successful allocation other context(ie, further stream allocation
part for accelarating I/O speed) is just optional so let's pass gfp down
from driver (ie, zcomp frontend) like normal MM convention.

[sergey.senozhatsky@gmail.com: add missing __vmalloc zero and highmem gfps]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When we're using LZ4 multi compression streams for zram swap, we found
out page allocation failure message in system running test.  That was
not only once, but a few(2 - 5 times per test).  Also, some failure
cases were continually occurring to try allocation order 3.

In order to make parallel compression private data, we should call
kzalloc() with order 2/3 in runtime(lzo/lz4).  But if there is no order
2/3 size memory to allocate in that time, page allocation fails.  This
patch makes to use vmalloc() as fallback of kmalloc(), this prevents
page alloc failure warning.

After using this, we never found warning message in running test, also
It could reduce process startup latency about 60-120ms in each case.

For reference a call trace :

    Binder_1: page allocation failure: order:3, mode:0x10c0d0
    CPU: 0 PID: 424 Comm: Binder_1 Tainted: GW 3.10.49-perf-g991d02b-dirty #20
    Call trace:
      dump_backtrace+0x0/0x270
      show_stack+0x10/0x1c
      dump_stack+0x1c/0x28
      warn_alloc_failed+0xfc/0x11c
      __alloc_pages_nodemask+0x724/0x7f0
      __get_free_pages+0x14/0x5c
      kmalloc_order_trace+0x38/0xd8
      zcomp_lz4_create+0x2c/0x38
      zcomp_strm_alloc+0x34/0x78
      zcomp_strm_multi_find+0x124/0x1ec
      zcomp_strm_find+0xc/0x18
      zram_bvec_rw+0x2fc/0x780
      zram_make_request+0x25c/0x2d4
      generic_make_request+0x80/0xbc
      submit_bio+0xa4/0x15c
      __swap_writepage+0x218/0x230
      swap_writepage+0x3c/0x4c
      shrink_page_list+0x51c/0x8d0
      shrink_inactive_list+0x3f8/0x60c
      shrink_lruvec+0x33c/0x4cc
      shrink_zone+0x3c/0x100
      try_to_free_pages+0x2b8/0x54c
      __alloc_pages_nodemask+0x514/0x7f0
      __get_free_pages+0x14/0x5c
      proc_info_read+0x50/0xe4
      vfs_read+0xa0/0x12c
      SyS_read+0x44/0x74
    DMA: 3397*4kB (MC) 26*8kB (RC) 0*16kB 0*32kB 0*64kB 0*128kB 0*256kB
         0*512kB 0*1024kB 0*2048kB 0*4096kB = 13796kB

[minchan@kernel.org: change vmalloc gfp and adding comment about gfp]
[sergey.senozhatsky@gmail.com: tweak comments and styles]
Signed-off-by: Kyeongdon Kim <kyeongdon.kim@lge.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We can end up allocating a new compression stream with GFP_KERNEL from
within the IO path, which may result is nested (recursive) IO
operations.  That can introduce problems if the IO path in question is a
reclaimer, holding some locks that will deadlock nested IOs.

Allocate streams and working memory using GFP_NOIO flag, forbidding
recursive IO and FS operations.

An example:

  inconsistent {IN-RECLAIM_FS-W} -> {RECLAIM_FS-ON-W} usage.
  git/20158 [HC0[0]:SC0[0]:HE1:SE1] takes:
   (jbd2_handle){+.+.?.}, at:  start_this_handle+0x4ca/0x555
  {IN-RECLAIM_FS-W} state was registered at:
     __lock_acquire+0x8da/0x117b
     lock_acquire+0x10c/0x1a7
     start_this_handle+0x52d/0x555
     jbd2__journal_start+0xb4/0x237
     __ext4_journal_start_sb+0x108/0x17e
     ext4_dirty_inode+0x32/0x61
     __mark_inode_dirty+0x16b/0x60c
     iput+0x11e/0x274
     __dentry_kill+0x148/0x1b8
     shrink_dentry_list+0x274/0x44a
     prune_dcache_sb+0x4a/0x55
     super_cache_scan+0xfc/0x176
     shrink_slab.part.14.constprop.25+0x2a2/0x4d3
     shrink_zone+0x74/0x140
     kswapd+0x6b7/0x930
     kthread+0x107/0x10f
     ret_from_fork+0x3f/0x70
  irq event stamp: 138297
  hardirqs last  enabled at (138297):  debug_check_no_locks_freed+0x113/0x12f
  hardirqs last disabled at (138296):  debug_check_no_locks_freed+0x33/0x12f
  softirqs last  enabled at (137818):  __do_softirq+0x2d3/0x3e9
  softirqs last disabled at (137813):  irq_exit+0x41/0x95

               other info that might help us debug this:
   Possible unsafe locking scenario:
         CPU0
         ----
    lock(jbd2_handle);
    <Interrupt>
      lock(jbd2_handle);

                *** DEADLOCK ***
  5 locks held by git/20158:
   #0:  (sb_writers#7){.+.+.+}, at: [<ffffffff81155411>] mnt_want_write+0x24/0x4b
   #1:  (&type->i_mutex_dir_key#2/1){+.+.+.}, at: [<ffffffff81145087>] lock_rename+0xd9/0xe3
   #2:  (&sb->s_type->i_mutex_key#11){+.+.+.}, at: [<ffffffff8114f8e2>] lock_two_nondirectories+0x3f/0x6b
   #3:  (&sb->s_type->i_mutex_key#11/4){+.+.+.}, at: [<ffffffff8114f909>] lock_two_nondirectories+0x66/0x6b
   #4:  (jbd2_handle){+.+.?.}, at: [<ffffffff811e31db>] start_this_handle+0x4ca/0x555

               stack backtrace:
  CPU: 2 PID: 20158 Comm: git Not tainted 4.1.0-rc7-next-20150615-dbg-00016-g8bdf555-dirty #211
  Call Trace:
    dump_stack+0x4c/0x6e
    mark_lock+0x384/0x56d
    mark_held_locks+0x5f/0x76
    lockdep_trace_alloc+0xb2/0xb5
    kmem_cache_alloc_trace+0x32/0x1e2
    zcomp_strm_alloc+0x25/0x73 [zram]
    zcomp_strm_multi_find+0xe7/0x173 [zram]
    zcomp_strm_find+0xc/0xe [zram]
    zram_bvec_rw+0x2ca/0x7e0 [zram]
    zram_make_request+0x1fa/0x301 [zram]
    generic_make_request+0x9c/0xdb
    submit_bio+0xf7/0x120
    ext4_io_submit+0x2e/0x43
    ext4_bio_write_page+0x1b7/0x300
    mpage_submit_page+0x60/0x77
    mpage_map_and_submit_buffers+0x10f/0x21d
    ext4_writepages+0xc8c/0xe1b
    do_writepages+0x23/0x2c
    __filemap_fdatawrite_range+0x84/0x8b
    filemap_flush+0x1c/0x1e
    ext4_alloc_da_blocks+0xb8/0x117
    ext4_rename+0x132/0x6dc
    ? mark_held_locks+0x5f/0x76
    ext4_rename2+0x29/0x2b
    vfs_rename+0x540/0x636
    SyS_renameat2+0x359/0x44d
    SyS_rename+0x1e/0x20
    entry_SYSCALL_64_fastpath+0x12/0x6f

[minchan@kernel.org: add stable mark]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Kyeongdon Kim <kyeongdon.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Kejian Yan says:

====================
dts: hisi: fixes no syscon fault when init mdio

This patchset fixes the bug that eth can't initial successful on hip05-D02
because the dts files doesn't match the source code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>