Pull xen fixes from Juergen Gross:

 - a small cleanup

 - a fix for a build error on ARM with some configs

 - a fix of a patch for the Xen gntdev driver

 - three patches for fixing a potential problem in the swiotlb-xen
   driver which Konrad was fine with me carrying them through the Xen
   tree

* tag 'for-linus-5.3a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/swiotlb: remember having called xen_create_contiguous_region()
  xen/swiotlb: simplify range_straddles_page_boundary()
  xen/swiotlb: fix condition for calling xen_destroy_contiguous_region()
  xen: avoid link error on ARM
  xen/gntdev.c: Replace vm_map_pages() with vm_map_pages_zero()
  xen/pciback: remove set but not used variable 'old_state'

Pull arm64 fixes from Catalin Marinas:

 - Update the compat layer to allow single-byte watchpoints on all
   addresses (similar to the native support)

 - arm_pmu: fix the restoration of the counters on the
   CPU_PM_ENTER_FAILED path

 - Fix build regression with vDSO and Makefile not stripping
   CROSS_COMPILE_COMPAT

 - Fix the CTR_EL0 (cache type register) sanitisation on heterogeneous
   machines (e.g. big.LITTLE)

 - Fix the interrupt controller priority mask value when pseudo-NMIs are
   enabled

 - arm64 kprobes fixes: recovering of the PSTATE.D flag in the
   single-step exception handler, NOKPROBE annotations for
   unwind_frame() and walk_stackframe(), remove unneeded
   rcu_read_lock/unlock from debug handlers

 - Several gcc fall-through warnings

 - Unused variable warnings

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Make debug exception handlers visible from RCU
  arm64: kprobes: Recover pstate.D in single-step exception handler
  arm64/mm: fix variable 'tag' set but not used
  arm64/mm: fix variable 'pud' set but not used
  arm64: Remove unneeded rcu_read_lock from debug handlers
  arm64: unwind: Prohibit probing on return_address()
  arm64: Lower priority mask for GIC_PRIO_IRQON
  arm64/efi: fix variable 'si' set but not used
  arm64: cpufeature: Fix feature comparison for CTR_EL0.{CWG,ERG}
  arm64: vdso: Fix Makefile regression
  arm64: module: Mark expected switch fall-through
  arm64: smp: Mark expected switch fall-through
  arm64: hw_breakpoint: Fix warnings about implicit fallthrough
  drivers/perf: arm_pmu: Fix failure path in PM notifier
  arm64: compat: Allow single-byte watchpoints on all addresses

Pull parisc fixes from Helge Deller:
 "A few small fixes for the parisc architecture:

   - Fix fall-through warnings in parisc math emu code

   - Fix vmlinuz linking failure with debug-enabled kernels

   - Fix a race condition in kernel live-patching code

   - Add missing archclean Makefile target & defconfig adjustments"

* 'parisc-5.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Add archclean Makefile target
  parisc: Strip debug info from kernel before creating compressed vmlinuz
  parisc: Fix build of compressed kernel even with debug enabled
  parisc: fix race condition in patching code
  parisc: rename default_defconfig to defconfig
  parisc: Fix fall-through warnings in fpudispatch.c
  parisc: Mark expected switch fall-throughs in fault.c

Pull s390 updates from Vasily Gorbik:

 - Default configs updates

 - Minor qdio cleanup

 - Sparse warnings fixes

 - Implicit-fallthrough warnings fixes

* tag 's390-5.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/zcrypt: adjust switch fall through comments for -Wimplicit-fallthrough
  vfio-ccw: make vfio_ccw_async_region_ops static
  s390/3215: add switch fall through comment for -Wimplicit-fallthrough
  s390/tape: add fallthrough annotations
  s390/mm: add fallthrough annotations
  s390/mm: make gmap_test_and_clear_dirty_pmd static
  s390/kexec: add missing include to machine_kexec_reloc.c
  s390/perf: make cf_diag_csd static
  s390/lib: add missing include
  s390/boot: add missing declarations and includes
  s390: update configs
  s390: clean up qdio.h

Pull SCSI fixes from James Bottomley:
 "Seven fixes to four drivers with no core changes.

  The mpt3sas one is theoretical until we get a CPU that goes up to 64
  bits physical, the qla2xxx one fixes an oops in a driver
  initialization error leg and the others are mostly cosmetic"

[ The fcoe patches may be worth highlighting - they may be "just"
  cleanups, but they simplify and fix the odd fc_rport_priv structure
  handling rules so that the new gcc-9 warnings about memset crossing
  structure boundaries are gone.

  The old code was hard for humans to understand too, and really
  confused the compiler sanity checks  - Linus ]

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Fix possible fcport null-pointer dereferences
  scsi: mpt3sas: Use 63-bit DMA addressing on SAS35 HBA
  scsi: hpsa: remove printing internal cdb on tag collision
  scsi: hpsa: correct scsi command status issue after reset
  scsi: fcoe: pass in fcoe_rport structure instead of fc_rport_priv
  scsi: fcoe: Embed fc_rport_priv in fcoe_rport structure
  scsi: libfc: Whitespace cleanup in libfc.h

Pull block fixes from Jens Axboe:
 "Here's a small collection of fixes that should go into this series.
  This contains:

   - io_uring potential use-after-free fix (Jackie)

   - loop regression fix (Jan)

   - O_DIRECT fragmented bio regression fix (Damien)

   - Mark Denis as the new floppy maintainer (Denis)

   - ataflop switch fall-through annotation (Gustavo)

   - libata zpodd overflow fix (Kees)

   - libata ahci deferred probe fix (Miquel)

   - nbd invalidation BUG_ON() fix (Munehisa)

   - dasd endless loop fix (Stefan)"

* tag 'for-linus-20190802' of git://git.kernel.dk/linux-block:
  s390/dasd: fix endless loop after read unit address configuration
  block: Fix __blkdev_direct_IO() for bio fragments
  MAINTAINERS: floppy: take over maintainership
  nbd: replace kill_bdev() with __invalidate_device() again
  ata: libahci: do not complain in case of deferred probe
  io_uring: fix KASAN use after free in io_sq_wq_submit_work
  loop: Fix mount(2) failure due to race with LOOP_SET_FD
  libata: zpodd: Fix small read overflow in zpodd_get_mech_type()
  ataflop: Mark expected switch fall-through

Merge tag 'for-5.3/dm-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:
 "Fix NULL pointer and various whitespace issues with DM's recent DAX
  code changes from commit in 5.3 merge"

* tag 'for-5.3/dm-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm table: fix various whitespace issues with recent DAX code
  dm table: fix dax_dev NULL dereference in device_synchronous()

Pull rdma fixes from Doug Ledford:
 "Here's our second -rc pull request. Nothing particularly special in
  this one. The client removal deadlock fix is kindy tricky, but we had
  multiple eyes on it and no one could find a fault in it. A couple
  Spectre V1 fixes too. Otherwise, all just normal -rc fodder:

   - A couple Spectre V1 fixes (umad, hfi1)

   - Fix a tricky deadlock in the rdma core code with refcounting
     instead of locks (client removal patches)

   - Build errors (hns)

   - Fix a scheduling while atomic issue (mlx5)

   - Use after free fix (mad)

   - Fix error path return code (hns)

   - Null deref fix (siw_crypto_hash)

   - A few other misc. minor fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/hns: Fix error return code in hns_roce_v1_rsv_lp_qp()
  RDMA/mlx5: Release locks during notifier unregister
  IB/hfi1: Fix Spectre v1 vulnerability
  IB/mad: Fix use-after-free in ib mad completion handling
  RDMA/restrack: Track driver QP types in resource tracker
  IB/mlx5: Fix MR registration flow to use UMR properly
  RDMA/devices: Remove the lock around remove_client_context
  RDMA/devices: Do not deadlock during client removal
  IB/core: Add mitigation for Spectre V1
  Do not dereference 'siw_crypto_shash' before checking
  RDMA/qedr: Fix the hca_type and hca_rev returned in device attributes
  RDMA/hns: Fix build error

Pull btrfs fixes from David Sterba:

 - tiny race window during 2 transactions aborting at the same time can
   accidentally lead to a commit

 - regression fix, possible deadlock during fiemap

 - fix for an old bug when incremental send can fail on a file that has
   been deduplicated in a special way

* tag 'for-5.3-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix deadlock between fiemap and transaction commits
  Btrfs: fix race leading to fs corruption after transaction abort
  Btrfs: fix incremental send failure after deduplication

Pull gfs2 fix from Andreas Gruenbacher:
 "Fix gfs2 cluster coherency bug"

* tag 'gfs2-v5.3-rc2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: Inode dirtying fix

Pull power management fix from Rafael Wysocki:
 "Fix recent regression affecting ACPI device power management"

* tag 'pm-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: PM: Fix regression in acpi_device_set_power()

Pull sound fixes from Takashi Iwai:

 - A further fix for syzcaller issues with USB-audio, addressing NULL
   dereference that was introduced by the recent fix

 - Avoid a long delay at boot with HD-audio when i915 module was built
   but not installed, found on some Debian systems

 - A fix of small race window at PCM draining

* tag 'sound-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usb-audio: Fix gpf in snd_usb_pipe_sanity_check
  ALSA: pcm: fix lost wakeup event scenarios in snd_pcm_drain
  ALSA: hda: Fix 1-minute detection delay when i915 module is not available

Pull drm fixes from Dave Airlie:
 "Thanks to Daniel for handling the email the last couple of weeks, flus
  and break-ins combined to derail me. Surprised nothing materialised
  today to take me out again.

  Just more amdgpu navi fixes, msm fixes and a single nouveau regression
  fix:

  amdgpu:
   - navi10 temperature and pstate fixes
   - vcn dynamic power management fix
   - CS ioctl error handling fix
   - debugfs info leak fix
   - amdkfd VegaM fix

  msm:
   - dma sync call fix
   - mdp5 dsi command mode fix
   - fall-through fixes
   - disabled GPU fix

  nouveau:
   - regression fix for displayport MST support"

* tag 'drm-fixes-2019-08-02' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau: Only release VCPI slots on mode changes
  drm: msm: Fix add_gpu_components
  drm/msm: Annotate intentional switch statement fall throughs
  drm/msm: add support for per-CRTC max_vblank_count on mdp5
  drm/msm: Use the correct dma_sync calls in msm_gem
  drm/amd/powerplay: correct UVD/VCE/VCN power status retrieval
  drm/amd/powerplay: correct Navi10 VCN powergate control (v2)
  drm/amd/powerplay: support VCN powergate status retrieval for SW SMU
  drm/amd/powerplay: support VCN powergate status retrieval on Raven
  drm/amd/powerplay: add new sensor type for VCN powergate status
  drm/amdgpu: fix a potential information leaking bug
  drm/amdgpu: fix error handling in amdgpu_cs_process_fence_dep
  drm/amd/powerplay: enable SW SMU reset functionality
  drm/amd/powerplay: fix null pointer dereference around dpm state relates
  drm/amdgpu/powerplay: use proper revision id for navi
  drm/amd/powerplay: fix temperature granularity error in smu11
  drm/amd/powerplay: add callback function of get_thermal_temperature_range
  drm/amdkfd: Fix byte align on VegaM

Pull clk fixes from Stephen Boyd:
 "A few fixes for code that came in during the merge window or that
  started getting exercised differently this time around:

   - Select regmap MMIO kconfig in spreadtrum driver to avoid compile
     errors

   - Complete kerneldoc on devm_clk_bulk_get_optional()

   - Register an essential clk earlier on mediatek mt8183 SoCs so the
     clocksource driver can use it

   - Fix divisor math in the at91 driver

   - Plug a race in Renesas reset control logic"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: renesas: cpg-mssr: Fix reset control race condition
  clk: sprd: Select REGMAP_MMIO to avoid compile errors
  clk: mediatek: mt8183: Register 13MHz clock earlier for clocksource
  clk: Add missing documentation of devm_clk_bulk_get_optional() argument
  clk: at91: generated: Truncate divisor to GENERATED_MAX_DIV + 1

Pull arm swiotlb support from Christoph Hellwig:
 "This fixes a cascade of regressions that originally started with the
  addition of the ia64 port, but only got fatal once we removed most
  uses of block layer bounce buffering in Linux 4.18.

  The reason is that while the original i386/PAE code that was the first
  architecture that supported > 4GB of memory without an iommu decided
  to leave bounce buffering to the subsystems, which in those days just
  mean block and networking as no one else consumed arbitrary userspace
  memory.

  Later with ia64, x86_64 and other ports we assumed that either an
  iommu or something that fakes it up ("software IOTLB" in beautiful
  Intel speak) is present and that subsystems can rely on that for
  dealing with addressing limitations in devices. Except that the ARM
  LPAE scheme that added larger physical address to 32-bit ARM did not
  follow that scheme and thus only worked by chance and only for block
  and networking I/O directly to highmem.

  Long story, short fix - add swiotlb support to arm when build for LPAE
  platforms, which actuallys turns out to be pretty trivial with the
  modern dma-direct / swiotlb code to fix the Linux 4.18-ish regression"

* tag 'arm-swiotlb-5.3' of git://git.infradead.org/users/hch/dma-mapping:
  arm: use swiotlb for bounce buffering on LPAE configs
  dma-mapping: check pfn validity in dma_common_{mmap,get_sgtable}

Pull dma-mapping regression fixes from Christoph Hellwig:
 "Two related regression fixes for changes from this merge window to fix
  alignment issues introduced in the CMA allocation rework (Nicolin
  Chen)"

* tag 'dma-mapping-5.3-3' of git://git.infradead.org/users/hch/dma-mapping:
  dma-contiguous: page-align the size in dma_free_contiguous()
  dma-contiguous: do not overwrite align in dma_alloc_contiguous()

Silence the following warnings when built with -Wimplicit-fallthrough=3
enabled by default since 5.3-rc2:
In file included from ./include/linux/preempt.h:11,
                 from ./include/linux/spinlock.h:51,
                 from ./include/linux/mmzone.h:8,
                 from ./include/linux/gfp.h:6,
                 from ./include/linux/slab.h:15,
                 from drivers/s390/crypto/ap_queue.c:13:
drivers/s390/crypto/ap_queue.c: In function 'ap_sm_recv':
./include/linux/list.h:577:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
  577 |  for (pos = list_first_entry(head, typeof(*pos), member); \
      |  ^~~
drivers/s390/crypto/ap_queue.c:147:3: note: in expansion of macro 'list_for_each_entry'
  147 |   list_for_each_entry(ap_msg, &aq->pendingq, list) {
      |   ^~~~~~~~~~~~~~~~~~~
drivers/s390/crypto/ap_queue.c:155:2: note: here
  155 |  case AP_RESPONSE_NO_PENDING_REPLY:
      |  ^~~~
drivers/s390/crypto/zcrypt_msgtype6.c: In function 'convert_response_ep11_xcrb':
drivers/s390/crypto/zcrypt_msgtype6.c:871:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
  871 |   if (msg->cprbx.cprb_ver_id == 0x04)
      |      ^
drivers/s390/crypto/zcrypt_msgtype6.c:874:2: note: here
  874 |  default: /* Unknown response type, this should NEVER EVER happen */
      |  ^~~~~~~
drivers/s390/crypto/zcrypt_msgtype6.c: In function 'convert_response_rng':
drivers/s390/crypto/zcrypt_msgtype6.c:901:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
  901 |   if (msg->cprbx.cprb_ver_id == 0x02)
      |      ^
drivers/s390/crypto/zcrypt_msgtype6.c:907:2: note: here
  907 |  default: /* Unknown response type, this should NEVER EVER happen */
      |  ^~~~~~~
drivers/s390/crypto/zcrypt_msgtype6.c: In function 'convert_response_xcrb':
drivers/s390/crypto/zcrypt_msgtype6.c:838:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
  838 |   if (msg->cprbx.cprb_ver_id == 0x02)
      |      ^
drivers/s390/crypto/zcrypt_msgtype6.c:844:2: note: here
  844 |  default: /* Unknown response type, this should NEVER EVER happen */
      |  ^~~~~~~
drivers/s390/crypto/zcrypt_msgtype6.c: In function 'convert_response_ica':
drivers/s390/crypto/zcrypt_msgtype6.c:801:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
  801 |   if (msg->cprbx.cprb_ver_id == 0x02)
      |      ^
drivers/s390/crypto/zcrypt_msgtype6.c:808:2: note: here
  808 |  default: /* Unknown response type, this should NEVER EVER happen */
      |  ^~~~~~~
Acked-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

Make debug exceptions visible from RCU so that synchronize_rcu()
correctly track the debug exception handler.

This also introduces sanity checks for user-mode exceptions as same
as x86's ist_enter()/ist_exit().

The debug exception can interrupt in idle task. For example, it warns
if we put a kprobe on a function called from idle task as below.
The warning message showed that the rcu_read_lock() caused this
problem. But actually, this means the RCU is lost the context which
is already in NMI/IRQ.

  /sys/kernel/debug/tracing # echo p default_idle_call >> kprobe_events
  /sys/kernel/debug/tracing # echo 1 > events/kprobes/enable
  /sys/kernel/debug/tracing # [  135.122237]
  [  135.125035] =============================
  [  135.125310] WARNING: suspicious RCU usage
  [  135.125581] 5.2.0-08445-g9187c508bdc7 #20 Not tainted
  [  135.125904] -----------------------------
  [  135.126205] include/linux/rcupdate.h:594 rcu_read_lock() used illegally while idle!
  [  135.126839]
  [  135.126839] other info that might help us debug this:
  [  135.126839]
  [  135.127410]
  [  135.127410] RCU used illegally from idle CPU!
  [  135.127410] rcu_scheduler_active = 2, debug_locks = 1
  [  135.128114] RCU used illegally from extended quiescent state!
  [  135.128555] 1 lock held by swapper/0/0:
  [  135.128944]  #0: (____ptrval____) (rcu_read_lock){....}, at: call_break_hook+0x0/0x178
  [  135.130499]
  [  135.130499] stack backtrace:
  [  135.131192] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.2.0-08445-g9187c508bdc7 #20
  [  135.131841] Hardware name: linux,dummy-virt (DT)
  [  135.132224] Call trace:
  [  135.132491]  dump_backtrace+0x0/0x140
  [  135.132806]  show_stack+0x24/0x30
  [  135.133133]  dump_stack+0xc4/0x10c
  [  135.133726]  lockdep_rcu_suspicious+0xf8/0x108
  [  135.134171]  call_break_hook+0x170/0x178
  [  135.134486]  brk_handler+0x28/0x68
  [  135.134792]  do_debug_exception+0x90/0x150
  [  135.135051]  el1_dbg+0x18/0x8c
  [  135.135260]  default_idle_call+0x0/0x44
  [  135.135516]  cpu_startup_entry+0x2c/0x30
  [  135.135815]  rest_init+0x1b0/0x280
  [  135.136044]  arch_call_rest_init+0x14/0x1c
  [  135.136305]  start_kernel+0x4d4/0x500
  [  135.136597]

So make debug exception visible to RCU can fix this warning.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

kprobes manipulates the interrupted PSTATE for single step, and
doesn't restore it. Thus, if we put a kprobe where the pstate.D
(debug) masked, the mask will be cleared after the kprobe hits.

Moreover, in the most complicated case, this can lead a kernel
crash with below message when a nested kprobe hits.

[  152.118921] Unexpected kernel single-step exception at EL1

When the 1st kprobe hits, do_debug_exception() will be called.
At this point, debug exception (= pstate.D) must be masked (=1).
But if another kprobes hits before single-step of the first kprobe
(e.g. inside user pre_handler), it unmask the debug exception
(pstate.D = 0) and return.
Then, when the 1st kprobe setting up single-step, it saves current
DAIF, mask DAIF, enable single-step, and restore DAIF.
However, since "D" flag in DAIF is cleared by the 2nd kprobe, the
single-step exception happens soon after restoring DAIF.

This has been introduced by commit 7419333f ("arm64: kprobe:
Always clear pstate.D in breakpoint exception handler")

To solve this issue, this stores all DAIF bits and restore it
after single stepping.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 7419333f ("arm64: kprobe: Always clear pstate.D in breakpoint exception handler")
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

After getting a storage server event that causes the DASD device driver
to update its unit address configuration during a device shutdown there is
the possibility of an endless loop in the device driver.

In the system log there will be ongoing DASD error messages with RC: -19.

The reason is that the loop starting the ruac request only terminates when
the retry counter is decreased to 0. But in the sleep_on function there are
early exit paths that do not decrease the retry counter.

Prevent an endless loop by handling those cases separately.

Remove the unnecessary do..while loop since the sleep_on function takes
care of retries by itself.

Fixes: 8e09f215 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org # 2.6.25+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

- Fix the dma_sync calls applied last week (Rob)
- Fix mdp5 dsi command mode (Brian)
- Squash fall through warnings (Jordan)
- Don't add disabled gpu nodes to the of device list (Jeffrey)

Cc: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Rob Clark <robdclark@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

# gpg: Signature made Fri 02 Aug 2019 05:54:27 AM AEST
# gpg:                using RSA key 96F70DFDA84A070A
# gpg: Can't check signature: public key not found
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190801200439.GV104440@art_vandelay

Looks like a regression got introduced into nv50_mstc_atomic_check()
that somehow didn't get found until now. If userspace changes
crtc_state->active to false but leaves the CRTC enabled, we end up
calling drm_dp_atomic_find_vcpi_slots() using the PBN calculated in
asyh->dp.pbn. However, if the display is inactive we end up calculating
a PBN of 0, which inadvertently causes us to have an allocation of 0.
>From there, if userspace then disables the CRTC afterwards we end up
accidentally attempting to free the VCPI twice:

WARNING: CPU: 0 PID: 1484 at drivers/gpu/drm/drm_dp_mst_topology.c:3336
drm_dp_atomic_release_vcpi_slots+0x87/0xb0 [drm_kms_helper]
RIP: 0010:drm_dp_atomic_release_vcpi_slots+0x87/0xb0 [drm_kms_helper]
Call Trace:
 drm_atomic_helper_check_modeset+0x3f3/0xa60 [drm_kms_helper]
 ? drm_atomic_check_only+0x43/0x780 [drm]
 drm_atomic_helper_check+0x15/0x90 [drm_kms_helper]
 nv50_disp_atomic_check+0x83/0x1d0 [nouveau]
 drm_atomic_check_only+0x54d/0x780 [drm]
 ? drm_atomic_set_crtc_for_connector+0xec/0x100 [drm]
 drm_atomic_commit+0x13/0x50 [drm]
 drm_atomic_helper_set_config+0x81/0x90 [drm_kms_helper]
 drm_mode_setcrtc+0x194/0x6a0 [drm]
 ? vprintk_emit+0x16a/0x230
 ? drm_ioctl+0x163/0x390 [drm]
 ? drm_mode_getcrtc+0x180/0x180 [drm]
 drm_ioctl_kernel+0xaa/0xf0 [drm]
 drm_ioctl+0x208/0x390 [drm]
 ? drm_mode_getcrtc+0x180/0x180 [drm]
 nouveau_drm_ioctl+0x63/0xb0 [nouveau]
 do_vfs_ioctl+0x405/0x660
 ? recalc_sigpending+0x17/0x50
 ? _copy_from_user+0x37/0x60
 ksys_ioctl+0x5e/0x90
 ? exit_to_usermode_loop+0x92/0xe0
 __x64_sys_ioctl+0x16/0x20
 do_syscall_64+0x59/0x190
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
WARNING: CPU: 0 PID: 1484 at drivers/gpu/drm/drm_dp_mst_topology.c:3336
drm_dp_atomic_release_vcpi_slots+0x87/0xb0 [drm_kms_helper]
---[ end trace 4c395c0c51b1f88d ]---
[drm:drm_dp_atomic_release_vcpi_slots [drm_kms_helper]] *ERROR* no VCPI for
[MST PORT:00000000e288eb7d] found in mst state 000000008e642070

So, fix this by doing what we probably should have done from the start: only
call drm_dp_atomic_find_vcpi_slots() when crtc_state->mode_changed is set, so
that VCPI allocations remain for as long as the CRTC is enabled.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 232c9eec ("drm/nouveau: Use atomic VCPI helpers for MST")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@redhat.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Karol Herbst <karolherbst@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: <stable@vger.kernel.org> # v5.1+
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190801220216.15323-1-lyude@redhat.com

drm-fixes-5.3-2019-07-31:

amdgpu:
- Fix temperature granularity for navi
- Fix stable pstate setting for navi
- Fix VCN DPM enablement on navi
- Fix error handling on CS ioctl when processing dependencies
- Fix possible information leak in debugfs

amdkfd:
- fix memory alignment for VegaM
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190731191648.25729-1-alexander.deucher@amd.com

Commit f850a48a ("ACPI: PM: Allow transitions to D0 to occur in
special cases") overlooked the fact that acpi_power_transition() may
change the power.state value for the target device and if that
happens, it may confuse acpi_device_set_power() and cause it to
omit the _PS0 evaluation which on some systems is necessary to
change power states of devices from low-power to D0.

Fix that by saving the current value of power.state for the
target device before passing it to acpi_power_transition() and
using the saved value in a subsequent check.

Fixes: f850a48a ("ACPI: PM: Allow transitions to D0 to occur in special cases")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>

The recent fix to properly handle IOCB_NOWAIT for async O_DIRECT IO
(patch 6a43074e) introduced two problems with BIO fragment handling
for direct IOs:
1) The dio size processed is calculated by incrementing the ret variable
by the size of the bio fragment issued for the dio. However, this size
is obtained directly from bio->bi_iter.bi_size AFTER the bio submission
which may result in referencing the bi_size value after the bio
completed, resulting in an incorrect value use.
2) The ret variable is not incremented by the size of the last bio
fragment issued for the bio, leading to an invalid IO size being
returned to the user.

Fix both problem by using dio->size (which is incremented before the bio
submission) to update the value of ret after bio submissions, including
for the last bio fragment issued.

Fixes: 6a43074e ("block: properly handle IOCB_NOWAIT for async O_DIRECT IO")
Reported-by: Masato Suzuki <masato.suzuki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Fix to return error code -ENOMEM from the rdma_zalloc_drv_obj() error
handling case instead of 0, as done elsewhere in this function.

Fixes: e8ac9389 ("RDMA: Fix allocation failure on pointer pd")
Fixes: 21a428a0 ("RDMA: Handle PD allocations by IB/core")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190801012725.150493-1-weiyongjun1@huawei.comSigned-off-by: Doug Ledford <dledford@redhat.com>

add_gpu_components() adds found GPU nodes from the DT to the match list,
regardless of the status of the nodes.  This is a problem, because if the
nodes are disabled, they should not be on the match list because they will
not be matched.  This prevents display from initing if a GPU node is
defined, but it's status is disabled.

Fix this by checking the node's status before adding it to the match list.

Fixes: dc3ea265 (drm/msm: Drop the gpu binding)
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626180015.45242-1-jeffrey.l.hugo@gmail.com

The below kernel panic was observed when created bond mode LACP
with GRE tunnel on top. The reason to it was not released spinlock
during mlx5 notify unregsiter sequence.

[  234.562007] BUG: scheduling while atomic: sh/10900/0x00000002
[  234.563005] Preemption disabled at:
[  234.566864] ------------[ cut here ]------------
[  234.567120] DEBUG_LOCKS_WARN_ON(val > preempt_count())
[  234.567139] WARNING: CPU: 16 PID: 10900 at kernel/sched/core.c:3203 preempt_count_sub+0xca/0x170
[  234.569550] CPU: 16 PID: 10900 Comm: sh Tainted: G        W 5.2.0-rc1-for-linust-dbg-2019-05-25_04-57-33-60 #1
[  234.569886] Hardware name: Dell Inc. PowerEdge R720/0X3D66, BIOS 2.6.1 02/12/2018
[  234.570183] RIP: 0010:preempt_count_sub+0xca/0x170
[  234.570404] Code: 03 38
d0 7c 08 84 d2 0f 85 b0 00 00 00 8b 15 dd 02 03 04 85 d2 75 ba 48 c7 c6
00 e1 88 83 48 c7 c7 40 e1 88 83 e8 76 11 f7 ff <0f> 0b 5b c3 65 8b 05
d3 1f d8 7e 84 c0 75 82 e8 62 c3 c3 00 85 c0
[  234.570911] RSP: 0018:ffff888b94477b08 EFLAGS: 00010286
[  234.571133] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
[  234.571391] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000246
[  234.571648] RBP: ffff888ba5560000 R08: fffffbfff08962d5 R09: fffffbfff08962d5
[  234.571902] R10: 0000000000000001 R11: fffffbfff08962d4 R12: ffff888bac6e9548
[  234.572157] R13: ffff888babfaf728 R14: ffff888bac6e9568 R15: ffff888babfaf750
[  234.572412] FS: 00007fcafa59b740(0000) GS:ffff888bed200000(0000) knlGS:0000000000000000
[  234.572686] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  234.572914] CR2: 00007f984f16b140 CR3: 0000000b2bf0a001 CR4: 00000000001606e0
[  234.573172] Call Trace:
[  234.573336] _raw_spin_unlock+0x2e/0x50
[  234.573542] mlx5_ib_unbind_slave_port+0x1bc/0x690 [mlx5_ib]
[  234.573793] mlx5_ib_cleanup_multiport_master+0x1d3/0x660 [mlx5_ib]
[  234.574039] mlx5_ib_stage_init_cleanup+0x4c/0x360 [mlx5_ib]
[  234.574271]  ? kfree+0xf5/0x2f0
[  234.574465] __mlx5_ib_remove+0x61/0xd0 [mlx5_ib]
[  234.574688]  ? __mlx5_ib_remove+0xd0/0xd0 [mlx5_ib]
[  234.574951] mlx5_remove_device+0x234/0x300 [mlx5_core]
[  234.575224] mlx5_unregister_device+0x4d/0x1e0 [mlx5_core]
[  234.575493] remove_one+0x4f/0x160 [mlx5_core]
[  234.575704] pci_device_remove+0xef/0x2a0
[  234.581407]  ? pcibios_free_irq+0x10/0x10
[  234.587143]  ? up_read+0xc1/0x260
[  234.592785] device_release_driver_internal+0x1ab/0x430
[  234.598442] unbind_store+0x152/0x200
[  234.604064]  ? sysfs_kf_write+0x3b/0x180
[  234.609441]  ? sysfs_file_ops+0x160/0x160
[  234.615021] kernfs_fop_write+0x277/0x440
[  234.620288]  ? __sb_start_write+0x1ef/0x2c0
[  234.625512] vfs_write+0x15e/0x460
[  234.630786] ksys_write+0x156/0x1e0
[  234.635988]  ? __ia32_sys_read+0xb0/0xb0
[  234.641120]  ? trace_hardirqs_off_thunk+0x1a/0x1c
[  234.646163] do_syscall_64+0x95/0x470
[  234.651106] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  234.656004] RIP: 0033:0x7fcaf9c9cfd0
[  234.660686] Code: 73 01
c3 48 8b 0d c0 6e 2d 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00
83 3d cd cf 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73
31 c3 48 83 ec 08 e8 ee cb 01 00 48 89 04 24
[  234.670128] RSP: 002b:00007ffd3b01ddd8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[  234.674811] RAX: ffffffffffffffda RBX: 000000000000000d RCX: 00007fcaf9c9cfd0
[  234.679387] RDX: 000000000000000d RSI: 00007fcafa5c1000 RDI: 0000000000000001
[  234.683848] RBP: 00007fcafa5c1000 R08: 000000000000000a R09: 00007fcafa59b740
[  234.688167] R10: 00007ffd3b01d8e0 R11: 0000000000000246 R12: 00007fcaf9f75400
[  234.692386] R13: 000000000000000d R14: 0000000000000001 R15: 0000000000000000
[  234.696495] irq event stamp: 153067
[  234.700525] hardirqs last enabled at (153067): [<ffffffff83258c39>] _raw_spin_unlock_irqrestore+0x59/0x70
[  234.704665] hardirqs last disabled at (153066): [<ffffffff83259382>] _raw_spin_lock_irqsave+0x22/0x90
[  234.708722] softirqs last enabled at (153058): [<ffffffff836006c5>] __do_softirq+0x6c5/0xb4e
[  234.712673] softirqs last disabled at (153051): [<ffffffff81227c1d>] irq_exit+0x17d/0x1d0
[  234.716601] ---[ end trace 5dbf096843ee9ce6 ]---

Fixes: df097a27 ("IB/mlx5: Use the new mlx5 core notifier API")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190731083852.584-1-leon@kernel.orgSigned-off-by: Doug Ledford <dledford@redhat.com>

sl is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.

Fix this by sanitizing sl before using it to index ibp->sl_to_sc.

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190731175428.GA16736@embeddedorSigned-off-by: Doug Ledford <dledford@redhat.com>

We encountered a use-after-free bug when unloading the driver:

[ 3562.116059] BUG: KASAN: use-after-free in ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.117233] Read of size 4 at addr ffff8882ca5aa868 by task kworker/u13:2/23862
[ 3562.118385]
[ 3562.119519] CPU: 2 PID: 23862 Comm: kworker/u13:2 Tainted: G           OE     5.1.0-for-upstream-dbg-2019-05-19_16-44-30-13 #1
[ 3562.121806] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014
[ 3562.123075] Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core]
[ 3562.124383] Call Trace:
[ 3562.125640]  dump_stack+0x9a/0xeb
[ 3562.126911]  print_address_description+0xe3/0x2e0
[ 3562.128223]  ? ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.129545]  __kasan_report+0x15c/0x1df
[ 3562.130866]  ? ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.132174]  kasan_report+0xe/0x20
[ 3562.133514]  ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.134835]  ? find_mad_agent+0xa00/0xa00 [ib_core]
[ 3562.136158]  ? qlist_free_all+0x51/0xb0
[ 3562.137498]  ? mlx4_ib_sqp_comp_worker+0x1970/0x1970 [mlx4_ib]
[ 3562.138833]  ? quarantine_reduce+0x1fa/0x270
[ 3562.140171]  ? kasan_unpoison_shadow+0x30/0x40
[ 3562.141522]  ib_mad_recv_done+0xdf6/0x3000 [ib_core]
[ 3562.142880]  ? _raw_spin_unlock_irqrestore+0x46/0x70
[ 3562.144277]  ? ib_mad_send_done+0x1810/0x1810 [ib_core]
[ 3562.145649]  ? mlx4_ib_destroy_cq+0x2a0/0x2a0 [mlx4_ib]
[ 3562.147008]  ? _raw_spin_unlock_irqrestore+0x46/0x70
[ 3562.148380]  ? debug_object_deactivate+0x2b9/0x4a0
[ 3562.149814]  __ib_process_cq+0xe2/0x1d0 [ib_core]
[ 3562.151195]  ib_cq_poll_work+0x45/0xf0 [ib_core]
[ 3562.152577]  process_one_work+0x90c/0x1860
[ 3562.153959]  ? pwq_dec_nr_in_flight+0x320/0x320
[ 3562.155320]  worker_thread+0x87/0xbb0
[ 3562.156687]  ? __kthread_parkme+0xb6/0x180
[ 3562.158058]  ? process_one_work+0x1860/0x1860
[ 3562.159429]  kthread+0x320/0x3e0
[ 3562.161391]  ? kthread_park+0x120/0x120
[ 3562.162744]  ret_from_fork+0x24/0x30
...
[ 3562.187615] Freed by task 31682:
[ 3562.188602]  save_stack+0x19/0x80
[ 3562.189586]  __kasan_slab_free+0x11d/0x160
[ 3562.190571]  kfree+0xf5/0x2f0
[ 3562.191552]  ib_mad_port_close+0x200/0x380 [ib_core]
[ 3562.192538]  ib_mad_remove_device+0xf0/0x230 [ib_core]
[ 3562.193538]  remove_client_context+0xa6/0xe0 [ib_core]
[ 3562.194514]  disable_device+0x14e/0x260 [ib_core]
[ 3562.195488]  __ib_unregister_device+0x79/0x150 [ib_core]
[ 3562.196462]  ib_unregister_device+0x21/0x30 [ib_core]
[ 3562.197439]  mlx4_ib_remove+0x162/0x690 [mlx4_ib]
[ 3562.198408]  mlx4_remove_device+0x204/0x2c0 [mlx4_core]
[ 3562.199381]  mlx4_unregister_interface+0x49/0x1d0 [mlx4_core]
[ 3562.200356]  mlx4_ib_cleanup+0xc/0x1d [mlx4_ib]
[ 3562.201329]  __x64_sys_delete_module+0x2d2/0x400
[ 3562.202288]  do_syscall_64+0x95/0x470
[ 3562.203277]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

The problem was that the MAD PD was deallocated before the MAD CQ.
There was completion work pending for the CQ when the PD got deallocated.
When the mad completion handling reached procedure
ib_mad_post_receive_mads(), we got a use-after-free bug in the following
line of code in that procedure:
   sg_list.lkey = qp_info->port_priv->pd->local_dma_lkey;
(the pd pointer in the above line is no longer valid, because the
pd has been deallocated).

We fix this by allocating the PD before the CQ in procedure
ib_mad_port_open(), and deallocating the PD after freeing the CQ
in procedure ib_mad_port_close().

Since the CQ completion work queue is flushed during ib_free_cq(),
no completions will be pending for that CQ when the PD is later
deallocated.

Note that freeing the CQ before deallocating the PD is the practice
in the ULPs.

Fixes: 4be90bc6 ("IB/mad: Remove ib_get_dma_mr calls")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190801121449.24973-1-leon@kernel.orgSigned-off-by: Doug Ledford <dledford@redhat.com>

The check for QP type different than XRC has excluded driver QP
types from the resource tracker.
As a result, "rdma resource show" user command would not show opened
driver QPs which does not reflect the real state of the system.

Check QP type explicitly instead of assuming enum values/ordering.

Fixes: 40909f66 ("RDMA/efa: Add EFA verbs implementation")
Signed-off-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190801104354.11417-1-galpress@amazon.comSigned-off-by: Doug Ledford <dledford@redhat.com>

Driver shouldn't allow to use UMR to register a MR when
umr_modify_atomic_disabled is set. Otherwise it will always end up with a
failure in the post send flow which sets the UMR WQE to modify atomic access
right.

Fixes: c8d75a98 ("IB/mlx5: Respect new UMR capabilities")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190731081929.32559-1-leon@kernel.orgSigned-off-by: Doug Ledford <dledford@redhat.com>

Due to the complexity of client->remove() callbacks it is desirable to not
hold any locks while calling them. Remove the last one by tracking only
the highest client ID and running backwards from there over the xarray.

Since the only purpose of that lock was to protect the linked list, we can
drop the lock.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190731081841.32345-3-leon@kernel.orgSigned-off-by: Doug Ledford <dledford@redhat.com>

lockdep reports:

   WARNING: possible circular locking dependency detected

   modprobe/302 is trying to acquire lock:
   0000000007c8919c ((wq_completion)ib_cm){+.+.}, at: flush_workqueue+0xdf/0x990

   but task is already holding lock:
   000000002d3d2ca9 (&device->client_data_rwsem){++++}, at: remove_client_context+0x79/0xd0 [ib_core]

   which lock already depends on the new lock.

   the existing dependency chain (in reverse order) is:

   -> #2 (&device->client_data_rwsem){++++}:
          down_read+0x3f/0x160
          ib_get_net_dev_by_params+0xd5/0x200 [ib_core]
          cma_ib_req_handler+0x5f6/0x2090 [rdma_cm]
          cm_process_work+0x29/0x110 [ib_cm]
          cm_req_handler+0x10f5/0x1c00 [ib_cm]
          cm_work_handler+0x54c/0x311d [ib_cm]
          process_one_work+0x4aa/0xa30
          worker_thread+0x62/0x5b0
          kthread+0x1ca/0x1f0
          ret_from_fork+0x24/0x30

   -> #1 ((work_completion)(&(&work->work)->work)){+.+.}:
          process_one_work+0x45f/0xa30
          worker_thread+0x62/0x5b0
          kthread+0x1ca/0x1f0
          ret_from_fork+0x24/0x30

   -> #0 ((wq_completion)ib_cm){+.+.}:
          lock_acquire+0xc8/0x1d0
          flush_workqueue+0x102/0x990
          cm_remove_one+0x30e/0x3c0 [ib_cm]
          remove_client_context+0x94/0xd0 [ib_core]
          disable_device+0x10a/0x1f0 [ib_core]
          __ib_unregister_device+0x5a/0xe0 [ib_core]
          ib_unregister_device+0x21/0x30 [ib_core]
          mlx5_ib_stage_ib_reg_cleanup+0x9/0x10 [mlx5_ib]
          __mlx5_ib_remove+0x3d/0x70 [mlx5_ib]
          mlx5_ib_remove+0x12e/0x140 [mlx5_ib]
          mlx5_remove_device+0x144/0x150 [mlx5_core]
          mlx5_unregister_interface+0x3f/0xf0 [mlx5_core]
          mlx5_ib_cleanup+0x10/0x3a [mlx5_ib]
          __x64_sys_delete_module+0x227/0x350
          do_syscall_64+0xc3/0x6a4
          entry_SYSCALL_64_after_hwframe+0x49/0xbe

Which is due to the read side of the client_data_rwsem being obtained
recursively through a work queue flush during cm client removal.

The lock is being held across the remove in remove_client_context() so
that the function is a fence, once it returns the client is removed. This
is required so that the two callers do not proceed with destruction until
the client completes removal.

Instead of using client_data_rwsem use the existing device unregistration
refcount and add a similar client unregistration (client->uses) refcount.

This will fence the two unregistration paths without holding any locks.

Cc: <stable@vger.kernel.org>
Fixes: 921eab11 ("RDMA/devices: Re-organize device.c locking")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190731081841.32345-2-leon@kernel.orgSigned-off-by: Doug Ledford <dledford@redhat.com>

Some processors may mispredict an array bounds check and
speculatively access memory that they should not. With
a user supplied array index we like to play things safe
by masking the value with the array size before it is
used as an index.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20190731043957.GA1600@agluck-desk2.amr.corp.intel.comSigned-off-by: Doug Ledford <dledford@redhat.com>

When CONFIG_KASAN_SW_TAGS=n, set_tag() is compiled away. GCC throws a
warning,

mm/kasan/common.c: In function '__kasan_kmalloc':
mm/kasan/common.c:464:5: warning: variable 'tag' set but not used
[-Wunused-but-set-variable]
  u8 tag = 0xff;
     ^~~

Fix it by making __tag_set() a static inline function the same as
arch_kasan_set_tag() in mm/kasan/kasan.h for consistency because there
is a macro in arch/arm64/include/asm/kasan.h,

 #define arch_kasan_set_tag(addr, tag) __tag_set(addr, tag)

However, when CONFIG_DEBUG_VIRTUAL=n and CONFIG_SPARSEMEM_VMEMMAP=y,
page_to_virt() will call __tag_set() with incorrect type of a
parameter, so fix that as well. Also, still let page_to_virt() return
"void *" instead of "const void *", so will not need to add a similar
cast in lowmem_page_address().
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Will Deacon <will@kernel.org>

Explicitly mark intentional fall throughs in switch statements to keep
-Wimplicit-fallthrough from complaining.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1564073588-27386-1-git-send-email-jcrouse@codeaurora.org

The mdp5 drm/kms driver currently does not work on command-mode DSI
panels due to 'vblank wait timed out' errors. This causes a latency
of seconds, or tens of seconds in some cases, before content is shown
on the panel. This hardware does not have the something that we can use
as a frame counter available when running in command mode, so we need to
fall back to using timestamps by setting the max_vblank_count to zero.
This can be done on a per-CRTC basis, so the convert mdp5 to use
drm_crtc_set_max_vblank_count().

This change was tested on a LG Nexus 5 (hammerhead) phone.
Suggested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190531094619.31704-3-masneyb@onstation.org

GCC throws a warning,

arch/arm64/mm/mmu.c: In function 'pud_free_pmd_page':
arch/arm64/mm/mmu.c:1033:8: warning: variable 'pud' set but not used
[-Wunused-but-set-variable]
  pud_t pud;
        ^~~

because pud_table() is a macro and compiled away. Fix it by making it a
static inline function and for pud_sect() as well.
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Will Deacon <will@kernel.org>

Remove rcu_read_lock()/rcu_read_unlock() from debug exception
handlers since we are sure those are not preemptible and
interrupts are off.
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>