- 31 Mar, 2016 33 commits
-
-
Dmitry V. Levin authored
commit 5f8d498d upstream. Explicitly check show_devname method return code and bail out in case of an error. This fixes regression introduced by commit 9d4d6574. Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
J. Bruce Fields authored
commit 2f6fc056 upstream. nfsd_lookup_dentry exits with the parent filehandle locked. fh_put also unlocks if necessary (nfsd filehandle locking is probably too lenient), so it gets unlocked eventually, but if the following op in the compound needs to lock it again, we can deadlock. A fuzzer ran into this; normal clients don't send a secinfo followed by a readdir in the same compound. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Magnus Damm authored
commit bcdc9f26 upstream. This patch fixes the MMC SPI driver from doing polling card detect when a CD GPIO that supports interrupts is specified using the gpios DT property. Without this patch the DT node below results in the following output: spi_gpio: spi-gpio { /* SD2 @ CN12 */ compatible = "spi-gpio"; #address-cells = <1>; #size-cells = <0>; gpio-sck = <&gpio6 16 GPIO_ACTIVE_HIGH>; gpio-mosi = <&gpio6 17 GPIO_ACTIVE_HIGH>; gpio-miso = <&gpio6 18 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; cs-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; status = "okay"; spi@0 { compatible = "mmc-spi-slot"; reg = <0>; voltage-ranges = <3200 3400>; spi-max-frequency = <25000000>; gpios = <&gpio6 22 GPIO_ACTIVE_LOW>; /* CD */ }; }; # dmesg | grep mmc mmc_spi spi32766.0: SD/MMC host mmc0, no WP, no poweroff, cd polling mmc0: host does not support reading read-only switch, assuming write-enable mmc0: new SDHC card on SPI mmcblk0: mmc0:0000 SU04G 3.69 GiB mmcblk0: p1 With this patch applied the "cd polling" portion above disappears. Signed-off-by:
Magnus Damm <damm+renesas@opensource.se> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Takashi Iwai authored
commit 1f7c6658 upstream. Cirrus HD-audio driver may adjust GPIO pins for EAPD dynamically depending on the jack plug state. This works fine for the auto-mute mode where the speaker gets muted upon the HP jack plug. OTOH, when the auto-mute mode is off, this turns off the EAPD unexpectedly depending on the jack state, which results in the silent speaker output. This patch fixes the silent speaker output issue by setting GPIO bits constantly when the auto-mute mode is off. Reported-and-tested-by: moosotc@gmail.com Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Dmitry Torokhov authored
commit 3b654288 upstream. Even though hid_hw_* checks that passed in data_len is less than HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device reports and select largest size. In-kernel users normally just send as much data as report needs, so there is no problem, but hidraw users can do whatever they please: BUG: KASAN: slab-out-of-bounds in memcpy+0x34/0x54 at addr ffffffc07135ea80 Write of size 4101 by task syz-executor/8747 CPU: 2 PID: 8747 Comm: syz-executor Tainted: G BU 3.18.0 #37 Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT) Call trace: [<ffffffc00020ebcc>] dump_backtrace+0x0/0x258 arch/arm64/kernel/traps.c:83 [<ffffffc00020ee40>] show_stack+0x1c/0x2c arch/arm64/kernel/traps.c:172 [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffc001958114>] dump_stack+0x90/0x140 lib/dump_stack.c:50 [< inline >] print_error_description mm/kasan/report.c:97 [< inline >] kasan_report_error mm/kasan/report.c:278 [<ffffffc0004597dc>] kasan_report+0x268/0x530 mm/kasan/report.c:305 [<ffffffc0004592e8>] __asan_storeN+0x20/0x150 mm/kasan/kasan.c:718 [<ffffffc0004594e0>] memcpy+0x30/0x54 mm/kasan/kasan.c:299 [<ffffffc001306354>] __i2c_hid_command+0x2b0/0x7b4 drivers/hid/i2c-hid/i2c-hid.c:178 [< inline >] i2c_hid_set_or_send_report drivers/hid/i2c-hid/i2c-hid.c:321 [<ffffffc0013079a0>] i2c_hid_output_raw_report.isra.2+0x3d4/0x4b8 drivers/hid/i2c-hid/i2c-hid.c:589 [<ffffffc001307ad8>] i2c_hid_output_report+0x54/0x68 drivers/hid/i2c-hid/i2c-hid.c:602 [< inline >] hid_hw_output_report include/linux/hid.h:1039 [<ffffffc0012cc7a0>] hidraw_send_report+0x400/0x414 drivers/hid/hidraw.c:154 [<ffffffc0012cc7f4>] hidraw_write+0x40/0x64 drivers/hid/hidraw.c:177 [<ffffffc0004681dc>] vfs_write+0x1d4/0x3cc fs/read_write.c:534 [< inline >] SYSC_pwrite64 fs/read_write.c:627 [<ffffffc000468984>] SyS_pwrite64+0xec/0x144 fs/read_write.c:614 Object at ffffffc07135ea80, in cache kmalloc-512 Object allocated with size 268 bytes. Let's check data length against the buffer size before attempting to copy data over. Reported-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
Dmitry Torokhov <dtor@chromium.org> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Bryn M. Reeves authored
commit 98dbc9c6 upstream. An "old" (.request_fn) DM 'struct request' stores a pointer to the associated 'struct dm_rq_target_io' in rq->special. dm_requeue_original_request(), previously named dm_requeue_unmapped_original_request(), called dm_unprep_request() to reset rq->special to NULL. But rq_end_stats() would go on to hit a NULL pointer deference because its call to tio_from_request() returned NULL. Fix this by calling rq_end_stats() _before_ dm_unprep_request() Signed-off-by:
Bryn M. Reeves <bmr@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Fixes: e262f347 ("dm stats: add support for request-based DM devices") Signed-off-by:
-
Dmitri Epshtein authored
commit 928b6519 upstream. Function eth_prepare_mac_addr_change() is called as part of MAC address change. This function check if interface is running. To enable change MAC address when interface is running: IFF_LIVE_ADDR_CHANGE flag must be set to dev->priv_flags field Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by:
Dmitri Epshtein <dima@marvell.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Ming Lei authored
commit fafcde3a upstream. Inside multipath_make_request(), multipath maps the incoming bio into low level device's bio, but it is totally wrong to copy the bio into mapped bio via '*mapped_bio = *bio'. For example, .__bi_remaining is kept in the copy, especially if the incoming bio is chained to via bio splitting, so .bi_end_io can't be called for the mapped bio at all in the completing path in this kind of situation. This patch fixes the issue by using clone style. Reported-and-tested-by:
Andrea Righi <righi.andrea@gmail.com> Signed-off-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Alex Deucher authored
commit e5f243bd upstream. Move all the logic to radeon_fb.c and add checks to functions called frome elsewhere. bug: https://bugzilla.kernel.org/show_bug.cgi?id=112781Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Sebastian Ott authored
commit 80c544de upstream. The function measurement block must not cross a page boundary. Ensure that by raising the alignment requirement to the smallest power of 2 larger than the size of the fmb. Fixes: d0b08853 ("s390/pci: performance statistics and debug infrastructure") Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Seth Forshee authored
commit 744742d6 upstream. The 'reqs' member of fuse_io_priv serves two purposes. First is to track the number of oustanding async requests to the server and to signal that the io request is completed. The second is to be a reference count on the structure to know when it can be freed. For sync io requests these purposes can be at odds. fuse_direct_IO() wants to block until the request is done, and since the signal is sent when 'reqs' reaches 0 it cannot keep a reference to the object. Yet it needs to use the object after the userspace server has completed processing requests. This leads to some handshaking and special casing that it needlessly complicated and responsible for at least one race condition. It's much cleaner and safer to maintain a separate reference count for the object lifecycle and to let 'reqs' just be a count of outstanding requests to the userspace server. Then we can know for sure when it is safe to free the object without any handshaking or special cases. The catch here is that most of the time these objects are stack allocated and should not be freed. Initializing these objects with a single reference that is never released prevents accidental attempts to free the objects. Fixes: 9d5722b7 ("fuse: handle synchronous iocbs internally") Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Robert Doebbelin authored
commit 7cabc61e upstream. There's a race in fuse_direct_IO(), whereby is_sync_kiocb() is called on an iocb that could have been freed if async io has already completed. The fix in this case is simple and obvious: cache the result before starting io. It was discovered by KASan: kernel: ================================================================== kernel: BUG: KASan: use after free in fuse_direct_IO+0xb1a/0xcc0 at addr ffff88036c414390 Signed-off-by:
Robert Doebbelin <robert@quobyte.com> Signed-off-by:
-
Vittorio Gambaletta (VittGam) authored
commit 4061db03 upstream. The clock measurement on the AC'97 audio card found in the IBM ThinkPad X41 will often fail, so add a quirk entry to fix it. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=441087Signed-off-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by:
-
Fabio Estevam authored
commit 33b96d2c upstream. Currently we have an incorrect behaviour when multiple devices are present under the weim node. For example: &weim { ... status = "okay"; sram@0,0 { ... status = "okay"; }; mram@0,0 { ... status = "disabled"; }; }; In this case only the 'sram' device should be probed and not 'mram'. However what happens currently is that the status variable is ignored, causing the 'sram' device to be disabled and 'mram' to be enabled. Change the weim_parse_dt() function to use for_each_available_child_of_node()so that the devices marked with 'status = disabled' are not probed. Suggested-by:
Wolfgang Netbal <wolfgang.netbal@sigmatek.at> Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by:
Sascha Hauer <s.hauer@pengutronix.de> Acked-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Lada Trimasova authored
commit f778cc65 upstream. read{l,w}() write{l,w}() primitives should use le{16,32}_to_cpu() and cpu_to_le{16,32}() respectively to ensure device registers are read correctly in Big Endian CPU configuration. Per Arnd Bergmann | Most drivers using readl() or readl_relaxed() expect those to perform byte | swaps on big-endian architectures, as the registers tend to be fixed endian This was needed for getting UART to work correctly on a Big Endian ARC. The ARC accessors originally were fine, and the bug got introduced inadventently by commit b8a03302 ("ARCv2: barriers") Fixes: b8a03302 ("ARCv2: barriers") Link: http://lkml.kernel.org/r/201603100845.30602.arnd@arndb.de Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Lada Trimasova <ltrimas@synopsys.com> [vgupta: beefed up changelog, added Fixes/stable tags] Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Johan Hedberg authored
commit 6a0e7807 upstream. The Add Advertising command handler does the appropriate checks for the AD and Scan Response data, however fails to take into account the general length of the mgmt command itself, which could lead to potential buffer overflows. This patch adds the necessary check that the mgmt command length is consistent with the given ad and scan_rsp lengths. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Max Filippov authored
commit 7de7ac78 upstream. There are XCHAL_NUM_DBREAK registers, clear them all. This also fixes cryptic assembler error message with binutils 2.25 when XCHAL_NUM_DBREAK is 0: as: out of memory allocating 18446744073709551575 bytes after a total of 495616 bytes Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
commit a67cc9aa upstream. Disabling pagefault makes little sense there, preemption disabling is what was meant. Signed-off-by:
-
Max Filippov authored
commit 362014c8 upstream. Simulator stdin may be connected to a file, when its end is reached kernel hangs in infinite loop inside rs_poll, because simc_poll always signals that descriptor 0 is readable and simc_read always returns 0. Check simc_read return value and exit loop if it's not positive. Also don't rewind polling timer if it's zero. Signed-off-by:
-
Hui Wang authored
commit 6ef2f68f upstream. This Lenovo ThinkCentre AIO also uses Line2 as mic mute button and uses GPIO2 to control the mic mute led, so applying this quirk can make both the button and led work. BugLink: https://bugs.launchpad.net/bugs/1555912Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Jenny Derzhavetz authored
commit f81bf458 upstream. No need to restrict this check to specific events. Signed-off-by:
Jenny Derzhavetz <jennyf@mellanox.com> Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [ kamal: backport to 4.2-stable: s/cm_id/np_cm_id/ ] Signed-off-by:
-
Jenny Derzhavetz authored
commit aea92980 upstream. We need an indication that isert_conn->iscsi_conn binding has happened so we'll know not to invoke a connection reinstatement on an unbound connection which will lead to a bogus isert_conn->conn dereferece. Signed-off-by:
-
Jenny Derzhavetz authored
commit b89a7c25 upstream. Once connection request is accepted, one rx descriptor is posted to receive login request. This descriptor has rx type, but is outside the main pool of rx descriptors, and thus was mistreated as tx type. Signed-off-by:
-
Joe Thornber authored
commit d14fcf3d upstream. Otherwise operations may be attempted that will only ever go on to crash (since the metadata device is either missing or unreliable if 'fail_io' is set). Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit 2eae9e44 upstream. If a transaction abort has failed then we can no longer use the metadata device. Typically this happens if the superblock is unreadable. This fix addresses a crash seen during metadata device failure testing. Fixes: 8a01a6af ("dm thin: prefetch missing metadata pages") Signed-off-by:
-
DingXiang authored
commit 4df2bf46 upstream. Otherwise loading a "snapshot" table using the same device for the origin and COW devices, e.g.: echo "0 20971520 snapshot 253:3 253:3 P 8" | dmsetup create snap will trigger: BUG: unable to handle kernel NULL pointer dereference at 0000000000000098 [ 1958.979934] IP: [<ffffffffa040efba>] dm_exception_store_set_chunk_size+0x7a/0x110 [dm_snapshot] [ 1958.989655] PGD 0 [ 1958.991903] Oops: 0000 [#1] SMP ... [ 1959.059647] CPU: 9 PID: 3556 Comm: dmsetup Tainted: G IO 4.5.0-rc5.snitm+ #150 ... [ 1959.083517] task: ffff8800b9660c80 ti: ffff88032a954000 task.ti: ffff88032a954000 [ 1959.091865] RIP: 0010:[<ffffffffa040efba>] [<ffffffffa040efba>] dm_exception_store_set_chunk_size+0x7a/0x110 [dm_snapshot] [ 1959.104295] RSP: 0018:ffff88032a957b30 EFLAGS: 00010246 [ 1959.110219] RAX: 0000000000000000 RBX: 0000000000000008 RCX: 0000000000000001 [ 1959.118180] RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff880329334a00 [ 1959.126141] RBP: ffff88032a957b50 R08: 0000000000000000 R09: 0000000000000001 [ 1959.134102] R10: 000000000000000a R11: f000000000000000 R12: ffff880330884d80 [ 1959.142061] R13: 0000000000000008 R14: ffffc90001c13088 R15: ffff880330884d80 [ 1959.150021] FS: 00007f8926ba3840(0000) GS:ffff880333440000(0000) knlGS:0000000000000000 [ 1959.159047] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1959.165456] CR2: 0000000000000098 CR3: 000000032f48b000 CR4: 00000000000006e0 [ 1959.173415] Stack: [ 1959.175656] ffffc90001c13040 ffff880329334a00 ffff880330884ed0 ffff88032a957bdc [ 1959.183946] ffff88032a957bb8 ffffffffa040f225 ffff880329334a30 ffff880300000000 [ 1959.192233] ffffffffa04133e0 ffff880329334b30 0000000830884d58 00000000569c58cf [ 1959.200521] Call Trace: [ 1959.203248] [<ffffffffa040f225>] dm_exception_store_create+0x1d5/0x240 [dm_snapshot] [ 1959.211986] [<ffffffffa040d310>] snapshot_ctr+0x140/0x630 [dm_snapshot] [ 1959.219469] [<ffffffffa0005c44>] ? dm_split_args+0x64/0x150 [dm_mod] [ 1959.226656] [<ffffffffa0005ea7>] dm_table_add_target+0x177/0x440 [dm_mod] [ 1959.234328] [<ffffffffa0009203>] table_load+0x143/0x370 [dm_mod] [ 1959.241129] [<ffffffffa00090c0>] ? retrieve_status+0x1b0/0x1b0 [dm_mod] [ 1959.248607] [<ffffffffa0009e35>] ctl_ioctl+0x255/0x4d0 [dm_mod] [ 1959.255307] [<ffffffff813304e2>] ? memzero_explicit+0x12/0x20 [ 1959.261816] [<ffffffffa000a0c3>] dm_ctl_ioctl+0x13/0x20 [dm_mod] [ 1959.268615] [<ffffffff81215eb6>] do_vfs_ioctl+0xa6/0x5c0 [ 1959.274637] [<ffffffff81120d2f>] ? __audit_syscall_entry+0xaf/0x100 [ 1959.281726] [<ffffffff81003176>] ? do_audit_syscall_entry+0x66/0x70 [ 1959.288814] [<ffffffff81216449>] SyS_ioctl+0x79/0x90 [ 1959.294450] [<ffffffff8167e4ae>] entry_SYSCALL_64_fastpath+0x12/0x71 ... [ 1959.323277] RIP [<ffffffffa040efba>] dm_exception_store_set_chunk_size+0x7a/0x110 [dm_snapshot] [ 1959.333090] RSP <ffff88032a957b30> [ 1959.336978] CR2: 0000000000000098 [ 1959.344121] ---[ end trace b049991ccad1169e ]--- Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1195899Signed-off-by:
Ding Xiang <dingxiang@huawei.com> Signed-off-by:
-
Takashi Iwai authored
commit 0ab1ace8 upstream. The commit [d507941b: ALSA: pcm: Correct PCM BUG error message] made the warning prefix back to "BUG:" due to its previous wrong prefix. But a kernel message containing "BUG:" seems taken as an Oops message wrongly by some brain-dead daemons, and it annoys users in the end. Instead of teaching daemons, change the string again to a more reasonable one. Fixes: 507941beb1e ('ALSA: pcm: Correct PCM BUG error message') Signed-off-by:
-
Dmitry Tunin authored
commit 75c6aca4 upstream. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3472 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1552925Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
-
Luck, Tony authored
commit eb1af3b7 upstream. Large memory Haswell-EX systems with multiple DIMMs per channel were sometimes reporting the wrong DIMM. Found three problems: 1) Debug printouts for socket and channel interleave were not interpreting the register fields correctly. The socket interleave field is a 2^X value (0=1, 1=2, 2=4, 3=8). The channel interleave is X+1 (0=1, 1=2, 2=3. 3=4). 2) Actual use of the socket interleave value didn't interpret as 2^X 3) Conversion of address to channel address was complicated, and wrong. Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Aristeu Rozanski <arozansk@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 56dc66ff upstream. Just like CX20722, CX7024 codec also requires the power down at reboot in order to reduce the noise at reboot/shutdown. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=113511Signed-off-by:
-
OGAWA Hirofumi authored
commit c0a2ad9b upstream. On umount path, jbd2_journal_destroy() writes latest transaction ID (->j_tail_sequence) to be used at next mount. The bug is that ->j_tail_sequence is not holding latest transaction ID in some cases. So, at next mount, there is chance to conflict with remaining (not overwritten yet) transactions. mount (id=10) write transaction (id=11) write transaction (id=12) umount (id=10) <= the bug doesn't write latest ID mount (id=10) write transaction (id=11) crash mount [recovery process] transaction (id=11) transaction (id=12) <= valid transaction ID, but old commit must not replay Like above, this bug become the cause of recovery failure, or FS corruption. So why ->j_tail_sequence doesn't point latest ID? Because if checkpoint transactions was reclaimed by memory pressure (i.e. bdev_try_to_free_page()), then ->j_tail_sequence is not updated. (And another case is, __jbd2_journal_clean_checkpoint_list() is called with empty transaction.) So in above cases, ->j_tail_sequence is not pointing latest transaction ID at umount path. Plus, REQ_FLUSH for checkpoint is not done too. So, to fix this problem with minimum changes, this patch updates ->j_tail_sequence, and issue REQ_FLUSH. (With more complex changes, some optimizations would be possible to avoid unnecessary REQ_FLUSH for example though.) BTW, journal->j_tail_sequence = ++journal->j_transaction_sequence; Increment of ->j_transaction_sequence seems to be unnecessary, but ext3 does this. Signed-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Douglas Gilbert authored
commit 5ecee0a3 upstream. One of the strange things that the original sg driver did was let the user provide both a data-out buffer (it followed the sg_header+cdb) _and_ specify a reply length greater than zero. What happened was that the user data-out buffer was copied into some kernel buffers and then the mid level was told a read type operation would take place with the data from the device overwriting the same kernel buffers. The user would then read those kernel buffers back into the user space. From what I can tell, the above action was broken by commit fad7f01e ("sg: set dxferp to NULL for READ with the older SG interface") in 2008 and syzkaller found that out recently. Make sure that a user space pointer is passed through when data follows the sg_header structure and command. Fix the abnormal case when a non-zero reply_len is also given. Fixes: fad7f01eSigned-off-by:
Douglas Gilbert <dgilbert@interlog.com> Reviewed-by:
Ewan Milne <emilne@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Mario Kleiner authored
commit 459ee1c3 upstream. As observed on Apple iMac10,1, DCE-3.2, RV-730, link rate of 2.7 Ghz is not selected, because the args.v1.ucConfig flag setting for 2.7 Ghz gets overwritten by a following assignment of the transmitter to use. Move link rate setup a few lines down to fix this. In practice this didn't have any positive or negative effect on display setup on the tested iMac10,1 so i don't know if backporting to stable makes sense or not. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by:
-
- 30 Mar, 2016 7 commits
-
-
NeilBrown authored
commit 550da24f upstream. break_stripe_batch_list breaks up a batch and copies some flags from the batch head to the members, preserving others. It doesn't preserve or copy STRIPE_PREREAD_ACTIVE. This is not normally a problem as STRIPE_PREREAD_ACTIVE is cleared when a stripe_head is added to a batch, and is not set on stripe_heads already in a batch. However there is no locking to ensure one thread doesn't set the flag after it has just been cleared in another. This does occasionally happen. md/raid5 maintains a count of the number of stripe_heads with STRIPE_PREREAD_ACTIVE set: conf->preread_active_stripes. When break_stripe_batch_list clears STRIPE_PREREAD_ACTIVE inadvertently this could becomes incorrect and will never again return to zero. md/raid5 delays the handling of some stripe_heads until preread_active_stripes becomes zero. So when the above mention race happens, those stripe_heads become blocked and never progress, resulting is write to the array handing. So: change break_stripe_batch_list to preserve STRIPE_PREREAD_ACTIVE in the members of a batch. URL: https://bugzilla.kernel.org/show_bug.cgi?id=108741 URL: https://bugzilla.redhat.com/show_bug.cgi?id=1258153 URL: http://thread.gmane.org/5649C0E9.2030204@zoner.cz Reported-by: Martin Svec <martin.svec@zoner.cz> (and others) Tested-by:
Tom Weber <linux@junkyard.4t2.com> Fixes: 1b956f7a ("md/raid5: be more selective about distributing flags across batch.") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Maurizio Lombardi authored
commit 84bd6499 upstream. In beiscsi_setup_boot_info(), the boot_kset pointer should be set to NULL in case of failure otherwise an invalid pointer dereference may occur later. Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Jitendra Bhivare <jitendra.bhivare@broadcom.com> Signed-off-by:
-
Bjorn Helgaas authored
commit b8941571 upstream. The Home Agent and PCU PCI devices in Broadwell-EP have a non-BAR register where a BAR should be. We don't know what the side effects of sizing the "BAR" would be, and we don't know what address space the "BAR" might appear to describe. Mark these devices as having non-compliant BARs so the PCI core doesn't touch them. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Tested-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Eric Wheeler authored
commit f8b11260 upstream. When bch_cache_set_alloc() fails to kzalloc the cache_set, the asyncronous closure handling tries to dereference a cache_set that hadn't yet been allocated inside of cache_set_flush() which is called by __cache_set_unregister() during cleanup. This appears to happen only during an OOM condition on bcache_register. Signed-off-by:
Eric Wheeler <bcache@linux.ewheeler.net> Signed-off-by:
-
Eric Wheeler authored
commit 9b299728 upstream. Fix null pointer dereference by changing register_cache() to return an int instead of being void. This allows it to return -ENOMEM or -ENODEV and enables upper layers to handle the OOM case without NULL pointer issues. See this thread: http://thread.gmane.org/gmane.linux.kernel.bcache.devel/3521 Fixes this error: gargamel:/sys/block/md5/bcache# echo /dev/sdh2 > /sys/fs/bcache/register bcache: register_cache() error opening sdh2: cannot allocate memory BUG: unable to handle kernel NULL pointer dereference at 00000000000009b8 IP: [<ffffffffc05a7e8d>] cache_set_flush+0x102/0x15c [bcache] PGD 120dff067 PUD 1119a3067 PMD 0 Oops: 0000 [#1] SMP Modules linked in: veth ip6table_filter ip6_tables (...) CPU: 4 PID: 3371 Comm: kworker/4:3 Not tainted 4.4.2-amd64-i915-volpreempt-20160213bc1 #3 Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 3904 04/27/2013 Workqueue: events cache_set_flush [bcache] task: ffff88020d5dc280 ti: ffff88020b6f8000 task.ti: ffff88020b6f8000 RIP: 0010:[<ffffffffc05a7e8d>] [<ffffffffc05a7e8d>] cache_set_flush+0x102/0x15c [bcache] Signed-off-by:
Marc MERLIN <marc@merlins.org> Signed-off-by:
-
Eric Wheeler authored
commit 07cc6ef8 upstream. The bch_writeback_thread might BUG_ON in read_dirty() if dc->sb==BDEV_STATE_DIRTY and bch_sectors_dirty_init has not yet completed its related initialization. This patch downs the dc->writeback_lock until after initialization is complete, thus preventing bch_writeback_thread from proceeding prematurely. See this thread: http://thread.gmane.org/gmane.linux.kernel.bcache.devel/3453Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Chris Friesen authored
commit f9c904b7 upstream. The callers of steal_account_process_tick() expect it to return whether a jiffy should be considered stolen or not. Currently the return value of steal_account_process_tick() is in units of cputime, which vary between either jiffies or nsecs depending on CONFIG_VIRT_CPU_ACCOUNTING_GEN. If cputime has nsecs granularity and there is a tiny amount of stolen time (a few nsecs, say) then we will consider the entire tick stolen and will not account the tick on user/system/idle, causing /proc/stats to show invalid data. The fix is to change steal_account_process_tick() to accumulate the stolen time and only account it once it's worth a jiffy. (Thanks to Frederic Weisbecker for suggestions to fix a bug in my first version of the patch.) Signed-off-by:
Chris Friesen <chris.friesen@windriver.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/56DBBDB8.40305@mail.usask.caSigned-off-by:
-
