the global refcount wasn't being increased after the first reference.
this caused an oops on unload on a multi-gpu card.
Signed-off-by: Dave Airlie <airlied@redhat.com>

The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.

this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.

Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Also add single crtc for RN50 chips.

changes in v2:
fix vblank init to respect single crtc flag
fix r100 mode bandwidth to respect single crtc flag
Signed-off-by: Dave Airlie <airlied@redhat.com>

We can get the corresponding info by adding the boot option of "drm.debug=
0x07". But On some boxes it will print the following message many times in
course of moving mouse. In such case the useful DRM debug info will be flushed.
   >[drm:drm_mode_cursor_ioctl],

Avoid using the DRM_DEBUG_KMS in drm_mode_cursor_ioctl.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

"Surround View" is an option in the system bios that
enables the AMD IGP chip in conjunction with a
discrete AMD card.  However, since the IGP vbios is
part of the system bios it is not accessible via the
rom bar or the legacy vga location.  When "Surround View"
is enabled in the system bios, the system bios puts a
copy of the IGP vbios image at the start of vram.

This patch adds support for reading the vbios image out
of vram on IGP cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Avivo hw have vblank interrupt in different place, fixes
irq handling (especialy irq disabling while suspending or
shuting down the module).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

R600 & RV770 family are all using atombios so remove dead code and
print an error message if we fail to find a valid atombios.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

When acceleration doesn't work we should free associated memory
and stop GPU block responsible for hardware acceleration so we
don't waste resource or let think one component of the driver that
a GPU feature is working/running while it doesn't actualy work.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We were calling reset unconditionaly in the startup path
this is bad we need to call GPU reset for a good reason
as after reset the GPU is in unknown states. To avoid any
more bad things to happen we now also unconditionaly
reinitialize the GPU after reset. This patch fix few issues
reported by different people regarding KMS & R6XX/RV7XX hw.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This split write back buffer handling into 3 functions,
wb_fini for cleanup, wb_enable/wb_disable for enabling/disabling
write back used for suspend/resume. This should fix
potential issue of letting the write back active before
suspending. We need to allocate memory in wb_enable because
we can only allocate once GART is running.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This remove old init path and allow code cleanup, now all hw
use the new init path, see top of radeon.h for description of
this.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. Do a massive RS600 register cleanup to clarify RS600
register, we are still bit fuzy on some register and waiting for
more informations. I don't have hw to test, so this patch is a
best effort to not break anythings and to try to improve things.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Also cleanup register specific to RS690/RS740. Version 2 add
missing header file for register, remove unecessary call to AGP
function and fix an indentation bug.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. More cleanup should happen latter to remove even more
callback. Also cleanup register specific to R100,RV200,RV250.
Version 2 correct the placement on IGP of the VRAM inside GPU address
space to match the stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Also cleanup register specific to R300.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Also cleanup register specific to RS400/RS480. This patch also fix
legacy VGA register used to disable VGA access we were programming
wrong register. Now we should properly disable VGA on r100 up to
rs400 asics. Note that RS400/RS480 resume is broken, it hangs the
computer while reprogramming dynamic clock, doesn't work either
without that patch. We need to spend more time investigating this
issue. Version 2 of the patch remove dead code that was left
commented out in the previous version. Version 3 correct the
placement on IGP of the VRAM inside GPU address space to match the
stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Convert the r520 asic support to new init path, change are smaller than
previous one as most of the architecture is now in place and more code
sharing can happen btw various asics.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Compiling the radeon DRM driver with !CONFIG_DEBUG_FS
throws the following warnings:

drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_debugfs_init':
drivers/gpu/drm/radeon/radeon_ttm.c:714: warning: unused variable 'i'
drivers/gpu/drm/radeon/radeon_ttm.c: At top level:
drivers/gpu/drm/radeon/radeon_ttm.c:692: warning: 'radeon_mem_types_list' defined but not used
drivers/gpu/drm/radeon/radeon_ttm.c:693: warning: 'radeon_mem_types_names' defined but not used

Fix: move these variables inside the #if defined(CONFIG_DEBUG_FS)
block in radeon_ttm_debugsfs_init(), which is the only place using them.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Compiling DRM throws the following warning if MAGIC_SYSRQ is disabled:

drivers/gpu/drm/drm_fb_helper.c:101: warning: 'sysrq_drm_fb_helper_restore_op' defined but not used

Fix: place sysrq_drm_fb_helper_restore_op and associated
definitions inside #ifdef CONFIG_MAGIC_SYSRQ.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>

The legacy r600 path shares code, but doesn't share quite enough
to get the freeing correct. Free the pages here also.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need add reloc offset to the offset in the actual
packet.  Fixes use of the DRAW_INDEX packet by the 3D
driver.

[airlied: modified first one where idx_value == ib[idx+0]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

All we need to do on r6xx/r7xx is clear the RADEON_IS_AGP
flag; the rest is handled in r600.c

fixes fdo bug 23990:
http://bugs.freedesktop.org/show_bug.cgi?id=23990Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Thanks to Michel for pointing this out to me, this is
why I need to get more sleep, over complicate this a bit.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Provides support for anti-tearing functionality
in the ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

- fix offset of NOP packet for parsing
- fix p->idx increments
- fix bad mask when updating crtc vline info
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

r6xx and r7xx was missing this.  We don't support
non-CPU accessible vram yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

If drivers don't init the fb helper on the connector, the cmdline
code won't work, but it shouldn't crash either.
Signed-off-by: Dave Airlie <airlied@redhat.com>

this avoids reading back the IB on AGP, also it avoids
the race where since we haven't fetched the page from the main IB
and written it to the gpu one, reading back fetches 0.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Got lots of untracked files after compiling.
These files are generated, thus should be ignored by git.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We shouldn't need these at all in radeon kms mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>

[note this requires an fb patch posted to linux-fbdev-devel already]

This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.

video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.

The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.

video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.

The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Having a : should be enough 'fb:' isn't really useful
if the fb wants to a kms output ID.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This avoids needing to do a kmalloc > PAGE_SIZE for the main
indirect buffer chunk, it adds an accessor for all reads from
the chunk and caches a single page at a time for subsequent
reads.

changes since v1:
Use a two page pool which should be the most common case
a single packet spanning > PAGE_SIZE will be hit, but I'm
having trouble seeing anywhere we currently generate anything like that.
hopefully proper short page copying at end
added parser_error flag to set deep errors instead of having to test
every ib value fetch.
fixed bug in patch that went to list.
Signed-off-by: Dave Airlie <airlied@redhat.com>

when I added the property I forgot to enable it.

Thanks to soreau on #radeon for tracking it down.
Signed-off-by: Dave Airlie <airlied@redhat.com>

I never changed this back when I wrote tv-out support.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Aspect ratio code of 0 means 1:1 before EDID 1.3.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>