dpt_i2o.c::adpt_i2o_to_scsi() reads the value at (reply+5) which
should contain the length in bytes of the transferred data. This
would be correct if reply was a u32 *. However it is a void * here,
so we need to read the value at (reply+20) instead.

The value at (reply+5) is usually 0xff0000, which is apparently
'large enough' and didn't cause any trouble until 2.6.27 where

commit 427e59f0
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date:   Sat Mar 8 18:24:17 2008 -0600

    [SCSI] make use of the residue value

caused this to become visible through e.g. iostat -x .
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Drivers want to be able to return DID_TRANSPORT_DISRUPTED and
have it do the right thing for commands like tape and passthrouh
as far as retries go. The LLDs previously used DID_BUS_BUSY or DID_ERROR
which followed the cmd->retries limit, but DID_TRANSPORT_DISRUPTED
was skipping that check so it could have caused a problem with tape
commands.

This patch has DID_TRANSPORT_DISRUPTED check the cmd->retries/cmd->allowed.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Fix multiple problems found in the hexdump data:
 - length calculation was wrong, traces were incomplete
 - FC payloads were dumped in different record than the output
   function tried to read
 - minor fixes in output
 - allow complete RSCN traces (up to 1024 bytes according to spec)
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

If an open port fsf request times out (in erp) the
corresponding erp_action member of the fsf
request need to set to NULL. If the port structure
will be removed later-on there will be still a
reference in the fsf request to the non existing
erp_action otherwise.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Attaching a unit immediately after setting the adapter online should
be possible. The problem right now is that the port_scan runs from a
workqueue and has not finished when the set_online call returns and
the sysfs structures for the ports are not available yet. Fix that by
waiting for the port scan to complete.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Fix leftover from last typecast patch:

drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_port_enqueue’:
drivers/s390/scsi/zfcp_aux.c:629: warning: format ‘%016llx’ expects
type ‘long long unsigned int’, but argument 3 has type ‘u64’
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Fix the handling of the request list in the error path:
 - Use irqsave for the lock as in the good path.
 - Before removing the request, check if it is still in the list, a
   call to dismiss_all might have changed the list in between.
 - zfcp_qdio_send does not change the queue counters on failure,
   trying revert something is wrong, so remove this.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

When allocating fsf requests without qtcb, store the pointer to the
mempool in the fsf requests for later call to mempool_free. This
codepath is only used by the status_read requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The per adapter req_list_lock must be held with interrupts disabled, otherwise
we might end up with nice deadlocks as lockdep tells us (see below).

zfcp 0.0.1804: QDIO problem occurred.

=========================================================
[ INFO: possible irq lock inversion dependency detected ]
2.6.27-rc8-00035-g4a770358-dirty #86
---------------------------------------------------------
swapper/0 just changed the state of lock:
 (&adapter->erp_lock){++..}, at: [<00000000002c82ae>] zfcp_erp_adapter_reopen+0x4e/0x8c
but this lock took another, hard-irq-unsafe lock in the past:
 (&adapter->req_list_lock){-+..}

and interrupts could create inverse lock ordering between them.

[tons of backtraces, but only the interesting part follows]

the second lock's dependencies:
-> (&adapter->req_list_lock){-+..} ops: 2280627634176 {
   initial-use  at:
                        [<0000000000071f10>] __lock_acquire+0x504/0x18bc
                        [<000000000007335c>] lock_acquire+0x94/0xbc
                        [<00000000003d7224>] _spin_lock_irqsave+0x6c/0xb0
                        [<00000000002cf684>] zfcp_fsf_req_dismiss_all+0x50/0x140
                        [<00000000002c87ee>] zfcp_erp_adapter_strategy_generic+0x66/0x3d0
                        [<00000000002c9498>] zfcp_erp_thread+0x88c/0x1318
                        [<000000000001b0d2>] kernel_thread_starter+0x6/0xc
                        [<000000000001b0cc>] kernel_thread_starter+0x0/0xc
   in-softirq-W at:
                        [<0000000000072172>] __lock_acquire+0x766/0x18bc
                        [<000000000007335c>] lock_acquire+0x94/0xbc
                        [<00000000003d7224>] _spin_lock_irqsave+0x6c/0xb0
                        [<00000000002ca73e>] zfcp_qdio_int_resp+0xbe/0x2ac
                        [<000000000027a1d6>] qdio_kick_inbound_handler+0x82/0xa0
                        [<000000000027daba>] tiqdio_inbound_processing+0x62/0xf8
                        [<0000000000047ba4>] tasklet_action+0x100/0x1f4
                        [<0000000000048b5a>] __do_softirq+0xae/0x154
                        [<0000000000021e4a>] do_softirq+0xea/0xf0
                        [<00000000000485de>] irq_exit+0xde/0xe8
                        [<0000000000268c64>] do_IRQ+0x160/0x1fc
                        [<00000000000261a2>] io_return+0x0/0x8
                        [<000000000001b8f8>] cpu_idle+0x17c/0x224
   hardirq-on-W at:
                        [<0000000000072190>] __lock_acquire+0x784/0x18bc
                        [<000000000007335c>] lock_acquire+0x94/0xbc
                        [<00000000003d702c>] _spin_lock+0x5c/0x9c
                        [<00000000002caff6>] zfcp_fsf_req_send+0x3e/0x158
                        [<00000000002ce7fe>] zfcp_fsf_exchange_config_data+0x106/0x124
                        [<00000000002c8948>] zfcp_erp_adapter_strategy_generic+0x1c0/0x3d0
                        [<00000000002c98ea>] zfcp_erp_thread+0xcde/0x1318
                        [<000000000001b0d2>] kernel_thread_starter+0x6/0xc
                        [<000000000001b0cc>] kernel_thread_starter+0x0/0xc
 }
 ... key      at: [<0000000000e356c8>] __key.26629+0x0/0x8
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmit@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

It is possible that a remote port has a problem, the SCSI device gets
deleted after the rport timeout and then the timeout for pending SCSI
commands trigger an abort. For this case, don't delete the reference
from the SCSI device to the zfcp unit, so that we can still have the
reference to issue an abort request.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Mike Reed noted
(https://bugzilla.novell.com/show_bug.cgi?id=421330) that the
driver was incorrectly returning a SUCCESS status if the driver's
request to the firmware to abort a command failed.  By doing so,
the mid-layer believed, incorrectly, that the command has
completed and has been returned (ultimately clearing
scsi_cmnd.request_buffer) yet the driver still has the command.
What should correctly happen is a mid-layer escalation
(device-reset, etc.) of recovery during which the driver will
eventually return the outstanding commands to the mid-layer.

Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

For 23XX ISPs, max_vports may return an invalid value.
Do not honour it.

Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

http://bugzilla.kernel.org/show_bug.cgi?id=9422Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Use correct block size (4K) for erase command 0x20 for Atmel
Flash. Use dword addresses for determining sector boundary.

Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

scsi_cmnd->cmnd was changed from a static array to a pointer post
2.6.25. It breaks mega_internal_command():

static int
mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru)
{
...
	scb = &adapter->int_scb;
	memset(scb, 0, sizeof(scb_t));

	scmd = &adapter->int_scmd;
	memset(scmd, 0, sizeof(Scsi_Cmnd));

	sdev = kzalloc(sizeof(struct scsi_device), GFP_KERNEL);
	scmd->device = sdev;

	scmd->device->host = adapter->host;
	scmd->host_scribble = (void *)scb;
	scmd->cmnd[0] = MEGA_INTERNAL_CMD;

mega_internal_command() uses scsi_cmnd allocated internally so
scmd->cmnd is NULL here. This patch adds a static array for cdb to
adapter_t and uses it here. This also uses
scsi_allocate_command/scsi_free_command, the recommended way to
allocate struct scsi_cmnd since the driver might use sense_buffer in
struct scsi_cmnd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Pascal Terjan <pterjan@gmail.com>
Reported-by: Pascal Terjan <pterjan@gmail.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  xfrm: Fix xfrm_policy_gc_lock handling.
  niu: Use pci_ioremap_bar().
  bnx2x: Version Update
  bnx2x: Calling netif_carrier_off at the end of the probe
  bnx2x: PCI configuration bug on big-endian
  bnx2x: Removing the PMF indication when unloading
  mv643xx_eth: fix SMI bus access timeouts
  net: kconfig cleanup
  fs_enet: fix polling
  XFRM: copy_to_user_kmaddress() reports local address twice
  SMC91x: Fix compilation on some platforms.
  udp: Fix the SNMP counter of UDP_MIB_INERRORS
  udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
  drivers/net/smc911x.c: Fix lockdep warning on xmit.

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: mask off DET when restoring SControl for detach
  libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
  libata: Fix a potential race condition in ata_scsi_park_show()
  sata_nv: fix generic, nf2/3 detection regression
  sata_via: restore vt*_prepare_host error handling
  sata_promise: add ATA engine reset to reset ops

Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling.  Mask off DET when restoring
SControl.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers.  Implement a horkage to skip the mod16 check and apply
it to the quantum device.

This is reported by John Clark in the following thread.

  http://thread.gmane.org/gmane.linux.ide/34748Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

All three flavors of sata_nv's are different in how their hardreset
behaves.

* generic: Hardreset is not reliable.  Link often doesn't come online
  after hardreset.

* nf2/3: A little bit better - link comes online with longer debounce
  timing.  However, nf2/3 can't reliable wait for the first D2H
  Register FIS, so it can't wait for device readiness or classify the
  device after hardreset.  Follow-up SRST required.

* ck804: Hardreset finally works.

The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors.  This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

commit b9d5b89b (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it

catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.

The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.

To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

From: Alexey Dobriyan <adobriyan@gmail.com>

Based upon a lockdep trace by Simon Arlott.

xfrm_policy_kill() can be called from both BH and
non-BH contexts, so we have to grab xfrm_policy_gc_lock
with BH disabling.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Updating the version
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.

If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again.  This would lead to occasional SMI access timeouts
when the system would be under heavy load.

The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

1. compile fix for irqreturn_t type change
2. restore ->poll_controller after CONFIG_PPC_CPM_NEW_BINDING transition
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: fix renaming one hardlink on top of another
  [CIFS] fix error in smb_send2
  [CIFS] Reduce number of socket retries in large write path

cifs: fix renaming one hardlink on top of another

POSIX says that renaming one hardlink on top of another to the same
inode is a no-op. We had the logic mostly right, but forgot to clear
the return code.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing, ring-buffer: add paranoid checks for loops
  ftrace: use kretprobe trampoline name to test in output
  tracing, alpha: undefined reference to `save_stack_trace'

Merge branch 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  io mapping: clean up #ifdefs
  io mapping: improve documentation
  i915: use io-mapping interfaces instead of a variety of mapping kludges
  resources: add io-mapping functions to dynamically map large device apertures
  x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda: make a STAC_DELL_EQ option
  ALSA: emu10k1 - Add more invert_shared_spdif flag to Audigy models
  ALSA: hda - Add a quirk for another Acer Aspire (1025:0090)
  ALSA: remove direct access of dev->bus_id in sound/isa/*
  sound: struct device - replace bus_id with dev_name(), dev_set_name()
  ALSA: Fix PIT lockup on some chipsets when using the PC-Speaker
  ALSA: rawmidi - Add open check in rawmidi callbacks
  ALSA: hda - Add digital-mic for ALC269 auto-probe mode
  ALSA: hda - Disable broken mic auto-muting in Realtek codes

* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
  proc: revert /proc/uptime to ->read_proc hook