- 04 May, 2016 40 commits
-
-
Robin Murphy authored
commit 07b48ac4 upstream. With the change to stashing just the IOVA-page-aligned remainder of the CPU-page offset rather than the whole thing, the failure path in __invalidate_sg() also needs tweaking to account for that in the case of differing page sizes where the two offsets may not be equivalent. Similarly in __finalise_sg(), lest the architecture-specific wrappers later get the wrong address for cache maintenance on sync or unmap. Fixes: 164afb1d ("iommu/dma: Use correct offset in map_sg") Reported-by:
Magnus Damm <damm+renesas@opensource.se> Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joerg Roedel authored
commit e3156048 upstream. Commit 61289cba ('iommu/amd: Remove old alias handling code') removed the old alias handling code from the AMD IOMMU driver because this is now handled by the IOMMU core code. But this also removed the handling of PCI aliases, which is not handled by the core code. This caused issues with PCI devices that have hidden PCIe-to-PCI bridges that rewrite the request-id. Fix this bug by re-introducing some of the removed functions from commit 61289cba and add a alias field 'struct iommu_dev_data'. This field carrys the return value of the get_alias() function and uses that instead of the amd_iommu_alias_table[] array in the code. Fixes: 61289cba ('iommu/amd: Remove old alias handling code') Tested-by:
Tomasz Golinski <tomaszg@math.uwb.edu.pl> Signed-off-by:
-
Keerthy authored
commit 56b367c0 upstream. pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices ranging from 1 to MAX. This leads to a corner case where we try to request the pin number = MAX and fails. bit_pos value is being calculted using ffs. pin_num_from_lsb uses bit_pos value. pins array is populated with: pin + pin_num_from_lsb. The above is 1 more than usual bit indices as bit_pos uses ffs to compute first set bit. Hence the last of the pins array is populated with the MAX value and not MAX - 1 which causes error when we call pin_request. mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1)) Consequently val_pos and submask are correct. Hence use __ffs which gives (ffs(x) - 1) as the first bit set. fixes: 4e7e8017 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules") Signed-off-by:
Keerthy <j-keerthy@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Yingjoe Chen authored
commit 5fedbb92 upstream. The debounce time unit for gpio_chip.set_debounce is us but mtk_gpio_set_debounce regard it as ms. Fix this by correct debounce time array dbnc_arr so it can find correct debounce setting. Debounce time for first debounce setting is 500us, correct this as well. While I'm at it, also change the debounce time array name to "debounce_time" for readability. Signed-off-by:
Yingjoe Chen <yingjoe.chen@mediatek.com> Reviewed-by:
Daniel Kurtz <djkurtz@chromium.org> Acked-by:
Hongzhou Yang <hongzhou.yang@mediatek.com> Signed-off-by:
-
Arnd Bergmann authored
commit 13aa38e2 upstream. The Xen framebuffer driver selects the xen keyboard driver, so the latter will be built-in if XEN_FBDEV_FRONTEND=y. However, when CONFIG_INPUT is a loadable module, this configuration cannot work. On mainline kernels, the symbol will be enabled but not used, while in combination with a patch I have to detect such useless configurations, we get the expected link failure: drivers/input/built-in.o: In function `xenkbd_remove': xen-kbdfront.c:(.text+0x2f0): undefined reference to `input_unregister_device' xen-kbdfront.c:(.text+0x30e): undefined reference to `input_unregister_device' This removes the extra "select", as it just causes more trouble than it helps. In theory, some defconfig file might break if it has XEN_FBDEV_FRONTEND in it but not INPUT_XEN_KBDDEV_FRONTEND. The Kconfig fragment we ship in the kernel (kernel/configs/xen.config) however already enables both, and anyone using an old .config file would keep having both enabled. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Suggested-by:
David Vrabel <david.vrabel@citrix.com> Fixes: 36c1132e ("xen kconfig: fix select INPUT_XEN_KBDDEV_FRONTEND") Acked-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Stephen Boyd authored
commit eda5ecc0 upstream. The trigger delay algorithm that converts from microseconds to the register value looks incorrect. According to most of the PMIC documentation, the equation is delay (Seconds) = (1 / 1024) * 2 ^ (x + 4) except for one case where the documentation looks to have a formatting issue and the equation looks like delay (Seconds) = (1 / 1024) * 2 x + 4 Most likely this driver was written with the improper documentation to begin with. According to the downstream sources the valid delays are from 2 seconds to 1/64 second, and the latter equation just doesn't make sense for that. Let's fix the algorithm and the range check to match the documentation and the downstream sources. Reported-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: 92d57a73 ("input: Add support for Qualcomm PMIC8XXX power key") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Tested-by:
John Stultz <john.stultz@linaro.org> Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Vladis Dronov authored
commit 162f98de upstream. The gtco driver expects at least one valid endpoint. If given malicious descriptors that specify 0 for the number of endpoints, it will crash in the probe function. Ensure there is at least one endpoint on the interface before using it. Also let's fix a minor coding style issue. The full correct report of this issue can be found in the public Red Hat Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1283385Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
-
Dmitry Ivanov authored
commit e2726020 upstream. All existing users of NETLINK_URELEASE use it to clean up resources that were previously allocated to a socket via some command. As a result, no users require getting this notification for unbound sockets. Sending it for unbound sockets, however, is a problem because any user (including unprivileged users) can create a socket that uses the same ID as an existing socket. Binding this new socket will fail, but if the NETLINK_URELEASE notification is generated for such sockets, the users thereof will be tricked into thinking the socket that they allocated the resources for is closed. In the nl80211 case, this will cause destruction of virtual interfaces that still belong to an existing hostapd process; this is the case that Dmitry noticed. In the NFC case, it will cause a poll abort. In the case of netlink log/queue it will cause them to stop reporting events, as if NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called. Fix this problem by checking that the socket is bound before generating the NETLINK_URELEASE notification. Signed-off-by:
Dmitry Ivanov <dima@ubnt.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dmitry Ivanov authored
commit 8f815cdd upstream. A non-privileged user can create a netlink socket with the same port_id as used by an existing open nl80211 netlink socket (e.g. as used by a hostapd process) with a different protocol number. Closing this socket will then lead to the notification going to nl80211's socket release notification handler, and possibly cause an action such as removing a virtual interface. Fix this issue by checking that the netlink protocol is NETLINK_GENERIC. Since generic netlink has no notifier chain of its own, we can't fix the problem more generically. Fixes: 026331c4 ("cfg80211/mac80211: allow registering for and sending action frames") Signed-off-by:
-
Anton Blanchard authored
commit 4705e024 upstream. We need to update the user TM feature bits (PPC_FEATURE2_HTM and PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature bit. At the moment, if firmware reports TM is not available we turn off the kernel TM feature bit but leave the userspace ones on. Userspace thinks it can execute TM instructions and it dies trying. This (together with a QEMU patch) fixes PR KVM, which doesn't currently support TM. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Anton Blanchard authored
commit beff8237 upstream. scan_features() updates cpu_user_features but not cpu_user_features2. Amongst other things, cpu_user_features2 contains the user TM feature bits which we must keep in sync with the kernel TM feature bit. Signed-off-by:
-
Anton Blanchard authored
commit 6997e57d upstream. The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU feature value, meaning all the remaining elements initialise the wrong values. This means instead of checking for byte 5, bit 0, we check for byte 0, bit 0, and then we incorrectly set the CPU feature bit as well as MMU feature bit 1 and CPU user feature bits 0 and 2 (5). Checking byte 0 bit 0 (IBM numbering), means we're looking at the "Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU. In practice that bit is set on all platforms which have the property. This means we set CPU_FTR_REAL_LE always. In practice that seems not to matter because all the modern cpus which have this property also implement REAL_LE, and we've never needed to disable it. We're also incorrectly setting MMU feature bit 1, which is: #define MMU_FTR_TYPE_8xx 0x00000002 Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E code, which can't run on the same cpus as scan_features(). So this also doesn't matter in practice. Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2 is not currently used, and bit 0 is: #define PPC_FEATURE_PPC_LE 0x00000001 Which says the CPU supports the old style "PPC Little Endian" mode. Again this should be harmless in practice as no 64-bit CPUs implement that mode. Fix the code by adding the missing initialisation of the MMU feature. Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It would be unsafe to start using it as old kernels incorrectly set it. Fixes: 44ae3ab3 ("powerpc: Free up some CPU feature bits by moving out MMU-related features") Signed-off-by:
-
Horia Geant? authored
commit 340ff60a upstream. After conversion to new AEAD interface, tcrypt tests fail as follows: [...] [ 1.145414] alg: aead: Test 1 failed on encryption for authenc-hmac-sha1-cbc-aes-talitos [ 1.153564] 00000000: 53 69 6e 67 6c 65 20 62 6c 6f 63 6b 20 6d 73 67 [ 1.160041] 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 1.166509] 00000020: 00 00 00 00 [...] Fix them by providing the correct cipher in & cipher out pointers, i.e. must skip over associated data in src and dst S/G. While here, fix a problem with the HW S/G table index usage: tbl_off must be updated after the pointer to the table entries is set. Fixes: aeb4c132 ("crypto: talitos - Convert to new AEAD interface") Reported-by:
Jonas Eymann <J.Eymann@gmx.net> Signed-off-by:
Horia Geant? <horia.geanta@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Jonas Eymann authored
commit 89d124cb upstream. Conversion of talitos driver to the new AEAD interface hasn't been properly tested. AEAD algorithms crash in talitos_cra_init as follows: [...] [ 1.141095] talitos ffe30000.crypto: hwrng [ 1.145381] Unable to handle kernel paging request for data at address 0x00000058 [ 1.152913] Faulting instruction address: 0xc02accc0 [ 1.157910] Oops: Kernel access of bad area, sig: 11 [#1] [ 1.163315] SMP NR_CPUS=2 P1020 RDB [ 1.166810] Modules linked in: [ 1.169875] CPU: 0 PID: 1007 Comm: cryptomgr_test Not tainted 4.4.6 #1 [ 1.176415] task: db5ec200 ti: db4d6000 task.ti: db4d6000 [ 1.181821] NIP: c02accc0 LR: c02acd18 CTR: c02acd04 [ 1.186793] REGS: db4d7d30 TRAP: 0300 Not tainted (4.4.6) [ 1.192457] MSR: 00029000 <CE,EE,ME> CR: 95009359 XER: e0000000 [ 1.198585] DEAR: 00000058 ESR: 00000000 GPR00: c017bdc0 db4d7de0 db5ec200 df424b48 00000000 00000000 df424bfc db75a600 GPR08: df424b48 00000000 db75a628 db4d6000 00000149 00000000 c0044cac db5acda0 GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000400 df424940 GPR24: df424900 00003083 00000400 c0180000 db75a640 c03e9f84 df424b40 df424b48 [ 1.230978] NIP [c02accc0] talitos_cra_init+0x28/0x6c [ 1.236039] LR [c02acd18] talitos_cra_init_aead+0x14/0x28 [ 1.241443] Call Trace: [ 1.243894] [db4d7de0] [c03e9f84] 0xc03e9f84 (unreliable) [ 1.249322] [db4d7df0] [c017bdc0] crypto_create_tfm+0x5c/0xf0 [ 1.255083] [db4d7e10] [c017beec] crypto_alloc_tfm+0x98/0xf8 [ 1.260769] [db4d7e40] [c0186a20] alg_test_aead+0x28/0xc8 [ 1.266181] [db4d7e60] [c0186718] alg_test+0x260/0x2e0 [ 1.271333] [db4d7ee0] [c0183860] cryptomgr_test+0x30/0x54 [ 1.276843] [db4d7ef0] [c0044d80] kthread+0xd4/0xd8 [ 1.281741] [db4d7f40] [c000e4a4] ret_from_kernel_thread+0x5c/0x64 [ 1.287930] Instruction dump: [ 1.290902] 38600000 4e800020 81230028 7c681b78 81490010 38e9ffc0 3929ffe8 554a073e [ 1.298691] 2b8a000a 7d474f9e 812a0008 91230030 <80e90058> 39270060 7c0004ac 7cc04828 Fixes: aeb4c132 ("crypto: talitos - Convert to new AEAD interface") Signed-off-by:
-
Xiaodong Liu authored
commit 0851561d upstream. In sha_complete_job, incorrect mcryptd_hash_request_ctx pointer is used when check and complete other jobs. If the memory of first completed req is freed, while still completing other jobs in the func, kernel will crash since NULL pointer is assigned to RIP. Signed-off-by:
Xiaodong Liu <xiaodong.liu@intel.com> Acked-by:
Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by:
-
Tom Lendacky authored
commit f709b45e upstream. Prevent information from leaking to userspace by doing a memset to 0 of the export state structure before setting the structure values and copying it. This prevents un-initialized padding areas from being copied into the export area. Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Matti Gottlieb authored
commit 7fdf9663 upstream. Currently paging download buffer is freed during the the unloading of the opmode which happens when the driver is unloaded. This causes a memory leak since the paging download buffer is allocated every time we enable the interface, so the download buffer can be allocated many times, but only be freed once. Free paging download buffer during disabling of the interface. Signed-off-by:
Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 9fc515bc upstream. IWL_INFO is not an error but still printed by default. "can't access the RSA semaphore it is write protected" seems worrisome but it is not really a problem. Signed-off-by:
-
Sebastian Ott authored
commit 9d89d9e6 upstream. Newer machines might use a different (larger) format for function measurement blocks. To ensure that we comply with the alignment requirement on these machines and prevent memory corruption (when firmware writes more data than we expect) add 16 padding bytes at the end of the fmb. Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Srinivas Pandruvada authored
commit 1becf035 upstream. When the config TDP level is not nominal (level = 0), the MSR values for reading level 1 and level 2 ratios contain power in low 14 bits and actual ratio bits are at bits [23:16]. The current processing for level 1 and level 2 is wrong as there is no shift done to get actual ratio. Fixes: 6a35fc2d (cpufreq: intel_pstate: get P1 from TAR when available) Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Alex Deucher authored
commit e9bef455 upstream. This reverts commit bedf2a65. See the radeon revert for an extended description. Signed-off-by:
-
Alex Deucher authored
commit bfaddd9f upstream. This reverts commit e64c952e. ATPX is the ACPI method for controlling AMD PowerXpress laptops. There are flags to indicate which methods are supported. If the dGPU power down flag is not supported, the driver needs to implement the dGPU power down manually. We had previously always forced the driver to assume the ATPX dGPU power down was present, but this causes problems on boards where it is not, leading to GPU hangs when attempting to power down the dGPU. Manual dGPU power down is not currently supported in the Linux driver. Some laptops indicate that the ATPX dGPU power down method is not present, but it actually apparently is. I'm not sure if this is a bios bug and it should be set or if there is a reason it was unset and the method should not be used. This is not an issue on other OSes since both the ATPX and the manual driver power down methods are supported. This is apparently fairly widespread, so just revert for now. bugs: https://bugzilla.kernel.org/show_bug.cgi?id=115321 https://bugzilla.kernel.org/show_bug.cgi?id=116581 https://bugzilla.kernel.org/show_bug.cgi?id=116251Signed-off-by:
-
Lyude authored
commit 9e60290d upstream. After unplugging a DP MST display from the system, we have to go through and destroy all of the DRM connectors associated with it since none of them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector() doesn't do a good enough job of ensuring that throughout the destruction process that no modesettings can be done with the connectors. As it is right now, intel_dp_destroy_mst_connector() works like this: * Take all modeset locks * Clear the configuration of the crtc on the connector, if there is one * Drop all modeset locks, this is required because of circular dependency issues that arise with trying to remove the connector from sysfs with modeset locks held * Unregister the connector * Take all modeset locks, again * Do the rest of the required cleaning for destroying the connector * Finally drop all modeset locks for good This only works sometimes. During the destruction process, it's very possible that a userspace application will attempt to do a modesetting using the connector. When we drop the modeset locks, an ioctl handler such as drm_mode_setcrtc has the oppurtunity to take all of the modeset locks from us. When this happens, one thing leads to another and eventually we end up committing a mode with the non-existent connector: [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training [drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f [drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization [drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f [drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi And in some cases, such as with the T460s using an MST dock, this results in breaking modesetting and/or panicking the system. To work around this, we now unregister the connector at the very beginning of intel_dp_destroy_mst_connector(), grab all the modesetting locks, and then hold them until we finish the rest of the function. Signed-off-by:
Lyude <cpaul@redhat.com> Signed-off-by:
Rob Clark <rclark@redhat.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1458155884-13877-1-git-send-email-cpaul@redhat.com (cherry picked from commit 1f771755) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
John Keeping authored
commit d59a1f71 upstream. The SPICE protocol considers the position of a cursor to be the location of its active pixel on the display, so the cursor is drawn with its top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor position gives the location where the top-left corner should be drawn, with the hotspot being a hint for drivers that need it. This fixes the location of the window resize cursors when using Fluxbox with the QXL DRM driver and both the QXL and modesetting X drivers. Signed-off-by:
John Keeping <john@metanate.com> Reviewed-by:
-
Ilia Mirkin authored
commit 78a121d8 upstream. Most calls to nvkm_ramht_new use 0x8000 as the size. This results in a fairly sizeable chunk of memory to be allocated, which may not be available with kzalloc. Since this is done fairly rarely (once per channel), use vzalloc instead. Signed-off-by:
Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Cc: Sven Joachim <svenjoac@gmx.de> Signed-off-by:
-
Davidlohr Bueso authored
commit fe1bce9e upstream. Otherwise an incoming waker on the dest hash bucket can miss the waiter adding itself to the plist during the lockless check optimization (small window but still the correct way of doing this); similarly to the decrement counterpart. Suggested-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Davidlohr Bueso <dbueso@suse.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: bigeasy@linutronix.de Cc: dvhart@infradead.org Link: http://lkml.kernel.org/r/1461208164-29150-1-git-send-email-dave@stgolabs.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 89e9e66b upstream. If userspace calls UNLOCK_PI unconditionally without trying the TID -> 0 transition in user space first then the user space value might not have the waiters bit set. This opens the following race: CPU0 CPU1 uval = get_user(futex) lock(hb) lock(hb) futex |= FUTEX_WAITERS .... unlock(hb) cmpxchg(futex, uval, newval) So the cmpxchg fails and returns -EINVAL to user space, which is wrong because the futex value is valid. To handle this (yes, yet another) corner case gracefully, check for a flag change and retry. [ tglx: Massaged changelog and slightly reworked implementation ] Fixes: ccf9e6a8 ("futex: Make unlock_pi more robust") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1460723739-5195-1-git-send-email-bigeasy@linutronix.deSigned-off-by:
-
Romain Perier authored
commit fba7cd68 upstream. The recent decoupling of pagefault disable and preempt disable added an explicit preempt_disable/enable() pair to the futex_atomic_cmpxchg_inatomic() implementation in asm-generic/futex.h. But it forgot to add preempt_enable() calls to the error handling code pathes, which results in a preemption count imbalance. This is observable on boot when the test for atomic_cmpxchg() is calling futex_atomic_cmpxchg_inatomic() on a NULL pointer. Add the missing preempt_enable() calls to the error handling code pathes. [ tglx: Massaged changelog ] Fixes: d9b9ff8c ("sched/preempt, futex: Disable preemption in UP futex_atomic_cmpxchg_inatomic() explicitly") Signed-off-by:
Romain Perier <romain.perier@free-electrons.com> Cc: linux-arch@vger.kernel.org Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1460640963-690-1-git-send-email-romain.perier@free-electrons.comSigned-off-by:
-
Conrad Kostecki authored
commit 037e1197 upstream. Fixes audio output on a ThinkPad X260, when using Lenovo CES 2013 docking station series (basic, pro, ultra). Signed-off-by:
Conrad Kostecki <ck+linuxkernel@bl4ckb0x.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 67f3754b upstream. The commit [9bef72bd: ALSA: pcxhr: Use nonatomic PCM ops] converted to non-atomic PCM ops, but shamelessly with an unbalanced mutex locking, which leads to the hangup easily. Fix it. Fixes: 9bef72bd ('ALSA: pcxhr: Use nonatomic PCM ops') Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116441Signed-off-by:
-
Lu, Han authored
commit 9859a971 upstream. Add HD Audio Device PCI ID for the Intel Broxton-T platform. It is an HDA Intel PCH controller. Signed-off-by:
Lu, Han <han.lu@intel.com> Signed-off-by:
-
Takashi Iwai authored
commit de3df8a9 upstream. Although one weird behavior about the input path (inconsistent D0/D3 switch) on Cirrus CS420x codecs was fixed in the previous commit, there is still an issue on some Mac machines: the capture stream stalls when switching the ADCs on the fly. More badly, this keeps stuck until the next reboot. The dynamic ADC switching is already a bit fragile and assuming optimistically that the chip accepts the frequent power changes. On Cirrus codecs, this doesn't seem applicable. As a quick workaround, we pin down the ADCs to keep up in D0 when spec->dyn_adc_switch is set. In this way, the ADCs are kept up only for the system that were confirmed to be broken. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171Signed-off-by:
-
Bastien Nocera authored
commit afecb146 upstream. The Optiplex 9020m with Haswell-DT processor needs a quirk for the headset jack at the front of the machine to be able to use microphones. A quirk for this model was originally added in 31278997, but c77900e6 removed it in favour of a more generic version. Unfortunately, pin configurations can changed based on firmware/BIOS versions, and the generic version doesn't have any effect on newer versions of the machine/firmware anymore. With help from David Henningsson <diwic@ubuntu.com> Signed-off-by:
Bastien Nocera <hadess@hadess.net> Tested-by:
-
Takashi Iwai authored
commit 50fd4987 upstream. We've got a regression report that the recording on Mac with a cirrus codec doesn't work any longer. This turned out to be the missing power up to D0 by power_save_node enablement. After analyzing the traces, we found out that the culprit is that the codec advertises the "actual" power state of a few nodes to be D0 while the "target" power state is D3. This inconsistency is usually OK, as it implies the power transition. But in the case of cirrus codec, this seems to be stuck to D3 while it's not actually D0. This patch addresses the issue by checking the power state difference more strictly. It sends the power-state change verb unless both the target and the actual power states show the given value. We may introduce yet another flag indicating the possible broken hardware power state, but it's anyway safer to set the proper power state even in a transition (at least it's harmless as long as the target state is same). So this simpler change was applied now. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171Signed-off-by:
-
Tony Luck authored
commit ff15e95c upstream. In commit: eb1af3b7 ("Fix computation of channel address") I switched the "sck_way" variable from holding the log2 value read from the h/w to instead be the actual number. Unfortunately it is needed in log2 form when used to shift the address. Tested-by:
Patrick Geary <patrickg@supermicro.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Aristeu Rozanski <arozansk@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac@vger.kernel.org Fixes: eb1af3b7 ("Fix computation of channel address") Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jan Beulich authored
commit 103f6112 upstream. Huge pages are not normally available to PV guests. Not suppressing hugetlbfs use results in an endless loop of page faults when user mode code tries to access a hugetlbfs mapped area (since the hypervisor denies such PTEs to be created, but error indications can't be propagated out of xen_set_pte_at(), just like for various of its siblings), and - once killed in an oops like this: kernel BUG at .../fs/hugetlbfs/inode.c:428! invalid opcode: 0000 [#1] SMP ... RIP: e030:[<ffffffff811c333b>] [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320 ... Call Trace: [<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40 [<ffffffff81167b3d>] evict+0xbd/0x1b0 [<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0 [<ffffffff81165b0e>] dput+0x1fe/0x220 [<ffffffff81150535>] __fput+0x155/0x200 [<ffffffff81079fc0>] task_work_run+0x60/0xa0 [<ffffffff81063510>] do_exit+0x160/0x400 [<ffffffff810637eb>] do_group_exit+0x3b/0xa0 [<ffffffff8106e8bd>] get_signal+0x1ed/0x470 [<ffffffff8100f854>] do_signal+0x14/0x110 [<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0 [<ffffffff814178a5>] retint_user+0x8/0x13 This is CVE-2016-3961 / XSA-174. Reported-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
Jan Beulich <jbeulich@suse.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <JGross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: xen-devel <xen-devel@lists.xenproject.org> Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.comSigned-off-by:
-
Catalin Marinas authored
commit fdc69e7d upstream. The set_pte_at() function must update the hardware PTE_RDONLY bit depending on the state of the PTE_WRITE and PTE_DIRTY bits of the given entry value. However, it currently only performs this for pte_valid() entries, ignoring PTE_PROT_NONE. The side-effect is that PROT_NONE mappings would not have the PTE_RDONLY bit set. Without CONFIG_ARM64_HW_AFDBM, this is not an issue since such PROT_NONE pages are not accessible anyway. With commit 2f4b829c ("arm64: Add support for hardware updates of the access and dirty pte bits"), the ptep_set_wrprotect() function was re-written to cope with automatic hardware updates of the dirty state. As an optimisation, only PTE_RDONLY is checked to assess the "dirty" status. Since set_pte_at() does not set this bit for PROT_NONE mappings, such pages may be considered "dirty" as a result of ptep_set_wrprotect(). This patch updates the pte_valid() check to pte_present() in set_pte_at(). It also adds PTE_PROT_NONE to the swap entry bits comment. Fixes: 2f4b829c ("arm64: Add support for hardware updates of the access and dirty pte bits") Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Reported-by:
Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com> Tested-by:
Ganapatrao Kulkarni <gkulkarni@cavium.com> Signed-off-by:
-
Catalin Marinas authored
commit ac15bd63 upstream. Currently, set_pte_at() only checks the software PTE_WRITE bit for user mappings when it sets or clears the hardware PTE_RDONLY accordingly. The kernel ptes are written directly without any modification, relying solely on the protection bits in macros like PAGE_KERNEL. However, modifying kernel pte attributes via pte_wrprotect() would be ignored by set_pte_at(). Since pte_wrprotect() does not set PTE_RDONLY (it only clears PTE_WRITE), the new permission is not taken into account. This patch changes set_pte_at() to adjust the read-only permission for kernel ptes as well. As a side effect, existing PROT_* definitions used for kernel ioremap*() need to include PTE_DIRTY | PTE_WRITE. (additionally, white space fix for PTE_KERNEL_ROX) Acked-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Tested-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Peter Zijlstra authored
commit 2f5177f0 upstream. The CPU controller hasn't kept up with the various changes in the whole cgroup initialization / destruction sequence, and commit: 2e91fa7f ("cgroup: keep zombies associated with their original cgroups") caused it to explode. The reason for this is that zombies do not inhibit css_offline() from being called, but do stall css_released(). Now we tear down the cfs_rq structures on css_offline() but zombies can run after that, leading to use-after-free issues. The solution is to move the tear-down to css_released(), which guarantees nobody (including no zombies) is still using our cgroup. Furthermore, a few simple cleanups are possible too. There doesn't appear to be any point to us using css_online() (anymore?) so fold that in css_alloc(). And since cgroup code guarantees an RCU grace period between css_released() and css_free() we can forgo using call_rcu() and free the stuff immediately. Suggested-by:
Tejun Heo <tj@kernel.org> Reported-by:
Kazuki Yamaguchi <k@rhe.jp> Reported-by:
Niklas Cassel <niklas.cassel@axis.com> Tested-by:
-
Robert Jarzmik authored
commit 6bab1c6a upstream. The current number of requestor lines is limited to 31. This was an error of a previous commit, as this number is platform dependent, and is actually : - for pxa25x: 40 requestor lines - for pxa27x: 75 requestor lines - for pxa3xx: 100 requestor lines The previous testing did not reveal the faulty constant as on pxa[23]xx platforms, only camera, MSL and USB are above requestor 32, and in these only the camera has a driver using dma. Fixes: e87ffbdf ("dmaengine: pxa_dma: fix the no-requestor case") Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Acked-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
