This patch adds interrupt support for R-Car thermal driver.

New generation R-Car thermal sensor interrupt controller was
different from old generation.
This patch supports new generation sensor only,
since the old generation interrupt controller had never been used before,
and will never be used in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

R-Car thermal driver will use struct common in next
feature (interrupt support).
But the register address is different between struct priv and common.
This patch adds read/write functions for struct common,
and use macro technique to avoid wrong register access.

This is preparation patch for next feature (interrupt support),
therefore, there is no user to use this common read/write
function at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

R-Car thermal sensor will be multi channel sensor in next generation.
But "IRQ controlling method" and "register mapping" are
different between old/new chip.

This patch adds multi sensor support.
Then, this driver assumes there is common register
if platform has IRQ resource.

The IRQ will be supported soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Current R-Car thermal driver is using spin lock for each
registers read/write, but it is pointless lock.
This lock is required while reading temperature,
but it needs long wait (= 300ms).
So, this patch used mutex lock while reading temperature,
instead of spin lock for each registers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

If CPCTL was 1 on R-Car thermal, the thermal comparator offset
is automatically decided by hardware.
And this CPCTL is the conditions which validate interrupt.
This patch enabled CPCTL.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Signed-off-by: Zhang Rui <rui.zhang@intel.com>

"level" parameter of get_cpu_frequency equals cooling state
of cpu cooling device, and it starts from 0.

Fix the misleading comment.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This patch adds support to set the emulated temperature method in
thermal zone (sensor). After setting this feature thermal zone may
report this temperature and not the actual temperature. The emulation
implementation may be based on sensor capability through platform
specific handler or pure software emulation if no platform handler defined.

This is useful in debugging different temperature threshold and its
associated cooling action. Critical threshold's cannot be emulated.
Writing 0 on this node should disable emulation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This value has already been clamped correctly to 0 through 49 in
powerclamp_set_cur_state() so this patch doesn't actually change
anything.  But we should fix it anyway for consistency.

set_target_ratio is used as an offset into an array with
MAX_TARGET_RATIO (50) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Below fixes are done to support falling threshold interrupt,
* Falling interrupt status macro corrected according to exynos5 data sheet.
* The get trend function modified to calculate trip temperature correctly.
* The clearing of interrupt status in the isr is now done after handling
  the event that caused the interrupt.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Intel PowerClamp driver performs synchronized idle injection across
all online CPUs. The goal is to maintain a given package level C-state
ratio.

Compared to other throttling methods already exist in the kernel,
such as ACPI PAD (taking CPUs offline) and clock modulation, this is often
more efficient in terms of performance per watt.

Please refer to Documentation/thermal/intel_powerclamp.txt for more details.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Allow drivers such as intel_powerclamp to use these apis for
turning on/off ticks during idle.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This patch adds an extra check in the data structure while registering
a thermal device. The check is to avoid registering zones with a number
of trips greater than zero, but with no .get_trip_temp nor .get_trip_type
callbacks. Receiving such data structure may end in wrong data access.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Change the logging messages to used dev_* helper functions.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

No need for spinlocks in this file, then removing its header.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This patch changes the function thermal_generate_netlink_event
to receive a thermal zone device instead of a originator id.

This way, the messages will always be bound to a thermal zone.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Hongbo Zhang <hongbo.zhang@stericsson.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Hongbo Zhang <hongbo.zhang@stericsson.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

devm_clk_get allocates a resource that is released when a driver detaches.
This patch uses devm_clk_get for data that is allocated in the probe
function of a platform device and is only released in the remove function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This patch adds .get_trip_type(), .get_trip_temp(), and .notify()
on rcar_thermal_zone_ops.
Driver will try platform power OFF if it reached to
critical temperature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

This patch supports exynos's emulation mode with newly created sysfs node.
Exynos 4x12 (4212, 4412) and 5 series provide emulation mode for thermal
management unit. Thermal emulation mode supports software debug for TMU's
operation. User can set temperature manually with software code and TMU
will read current temperature from user value not from sensor's value.
This patch includes also documentary placed under Documentation/thermal/.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Signed-off-by: Zhang Rui <rui.zhang@intel.com>

step_wise governor should set the device cooling state to
upper/lower limit directly when THERMAL_TREND_RAISE/DROP_FULL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

These two new thermal_trend types are used to tell the governor
that the temeprature is raising/dropping quickly.

Thermal cooling governors should handle this situation and make
proper decisions, e.g. set cooling state to upper/lower limit directly
instead of one step each time.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

Pull pinctrl fixes from Linus Walleij:
 "A first round of pinctrl fixes for v3.8:
   - i.MX5 register configuration
   - Swap a kfree to devm_kfree() to avoid memory corruption in the at91
     driver
   - Add the missing device tree binding doc for the SIRF pin controller
   - Enable the SIRF GPIO pull up/down configuration from the device
     tree, it was previously retired from the hard-coded approach.
   - NULL check for the prcm_base in the Nomadik pin controller.
   - Provide the prcm_base from the device tree in the DT boot path for
     the Nomadik pin controller."

* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  ARM: ux500: add pinctrl address resources
  pinctrl: nomadik: return if prcm_base is NULL
  pinctrl: sirf: enable GPIO pullup/down configuration from dts
  pinctrl: sirf: add missing DT-binding document
  pinctrl: fix comment mistake
  drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
  pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration

Pull f2fs bug fixes from Jaegeuk Kim:
 "This patch-set includes two major bug fixes:
   - incorrect IUsed provided by *df -i*, and
   - lookup failure of parent inodes in corner cases.

  [Other Bug Fixes]
   - Fix error handling routines
   - Trigger recovery process correctly
   - Resolve build failures due to missing header files

  [Etc]
   - Add a MAINTAINERS entry for f2fs
   - Fix and clean up variables, functions, and equations
   - Avoid warnings during compilation"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
  f2fs: unify string length declarations and usage
  f2fs: clean up unused variables and return values
  f2fs: clean up the start_bidx_of_node function
  f2fs: remove unneeded variable from f2fs_sync_fs
  f2fs: fix fsync_inode list addition logic and avoid invalid access to memory
  f2fs: remove unneeded initialization of nr_dirty in dirty_seglist_info
  f2fs: handle error from f2fs_iget_nowait
  f2fs: fix equation of has_not_enough_free_secs()
  f2fs: add MAINTAINERS entry
  f2fs: return a default value for non-void function
  f2fs: invalidate the node page if allocation is failed
  f2fs: add missing #include <linux/prefetch.h>
  f2fs: do f2fs_balance_fs in front of dir operations
  f2fs: should recover orphan and fsync data
  f2fs: fix handling errors got by f2fs_write_inode
  f2fs: fix up f2fs_get_parent issue to retrieve correct parent inode number
  f2fs: fix wrong calculation on f_files in statfs
  f2fs: remove set_page_dirty for atomic f2fs_end_io_write

Pull GFS2 fixes from Steven Whitehouse:
 "Here are four small bug fixes for GFS2.  There is no common theme here
  really, just a few items that were fixed recently.

  The first fixes lock name generation when the glock number is 0.  The
  second fixes a race allocating reservation structures and the final
  two fix a performance issue by making small changes in the allocation
  code."

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Reset rd_last_alloc when it reaches the end of the rgrp
  GFS2: Stop looking for free blocks at end of rgrp
  GFS2: Fix race in gfs2_rs_alloc
  GFS2: Initialize hex string to '0'

Pull powerpc fixes from Ben Herrenschmidt:
 "Here are a couple of small powerpc fixes.  They aren't new bugs (and
  they are both CCed to stable) but I didn't see the point of sitting on
  the fixes any longer."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Add missing NULL terminator to avoid boot panic on PPC40x
  powerpc/vdso: Remove redundant locking in update_vsyscall_tz()

Linux was granted a new system call to load modules by file descriptor
in commit 34e1169d ("module: add syscall to load module from fd").

Wire it up for ia64 (ready for the Chrome port :-)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The missing NULL terminator can cause a panic on
PPC405 boards during boot:

  Linux/PowerPC load: console=ttyS0,115200 root=/dev/mtdblock1 rootfstype=squashfs,jffs2 noinitrd init=/etc/preinit
  Finalizing device tree... flat tree at 0x6a5160
  bootconsole [udbg0] enabled
  Page fault in user mode with in_atomic() = 1 mm = (null)
  NIP = c0275f50  MSR = fffffffe
  Oops: Weird page fault, sig: 11 [#1]
  PowerPC 40x Platform
  Modules linked in:
  NIP: c0275f50 LR: c0275f60 CTR: c0280000
  REGS: c0275eb0 TRAP: 636f7265   Not tainted  (3.7.1)
  MSR: fffffffe <VEC,VSX,EE,PR,FP,ME,SE,BE,IR,DR,PMM,RI> CR: c06a6190  XER: 00000001
  TASK = c02662a8[0] 'swapper' THREAD: c0274000
  GPR00: c0275ec0 c000c658 c027c4bf 00000000 c0275ee0 c000a0ec c020a1a8 c020a1f0
  GPR08: c020f631 c020f404 c025f078 c025f080 c0275f10
   Call Trace:
   ---[ end trace 31fd0ba7d8756001 ]---

  Kernel panic - not syncing: Attempted to kill the idle task!

The panic happens since commit 9597abe0
(sections: fix section conflicts in arch/powerpc), however the root
cause of this is that the NULL terminator were not added in commit
a4f740cf (of/flattree: Add of_flat_dt_match()
helper function).

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The locking in update_vsyscall_tz() is not only unnecessary because the vdso
code copies the data unproteced in __kernel_gettimeofday() but also
introduces a hard to reproduce race condition between update_vsyscall()
and update_vsyscall_tz(), which causes user space process to loop
forever in vdso code.

The following patch removes the locking from update_vsyscall_tz().

Locking is not only unnecessary because the vdso code copies the data
unprotected in __kernel_gettimeofday() but also erroneous because updating
the tb_update_count is not atomic and introduces a hard to reproduce race
condition between update_vsyscall() and update_vsyscall_tz(), which further
causes user space process to loop forever in vdso code.

The below scenario describes the race condition,
x==0	Boot CPU			other CPU
	proc_P: x==0
	    timer interrupt
		update_vsyscall
x==1		    x++;sync		settimeofday
					    update_vsyscall_tz
x==2						x++;sync
x==3		    sync;x++
						sync;x++
	proc_P: x==3 (loops until x becomes even)

Because the ++ operator would be implemented as three instructions and not
atomic on powerpc.

A similar change was made for x86 in commit 6c260d58
("x86: vdso: Remove bogus locking in update_vsyscall_tz")
Signed-off-by: Shan Hai <shan.hai@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull LED fix from Bryan Wu.

* 'fixes-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: leds-gpio: set devm_gpio_request_one() flags param correctly

commit a99d76f9 leds: leds-gpio: use gpio_request_one

changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()

Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.

The gpio_request_one() flags parameter was set to:

GPIOF_DIR_OUT | (led_dat->active_low ^ state)

Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.

This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.

With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().

int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
..
	if (flags & GPIOF_DIR_IN)
		err = gpio_direction_input(gpio);
	else
		err = gpio_direction_output(gpio,
				(flags & GPIOF_INIT_HIGH) ? 1 : 0);
..
}

The right semantic is to evaluate led_dat->active_low ^ state and
set the output initial level explicitly.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>

Pull watchdog fixes from Wim Van Sebroeck:
 "This fixes some small errors in the new da9055 driver, eliminates a
  compiler warning and adds DT support for the twl4030_wdt driver (so
  that we can have multiple watchdogs with DT on the omap platforms)."

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: twl4030_wdt: add DT support
  watchdog: omap_wdt: eliminate unused variable and a compiler warning
  watchdog: da9055: Don't update wdt_dev->timeout in da9055_wdt_set_timeout error path
  watchdog: da9055: Fix invalid free of devm_ allocated data

Pull PCI updates from Bjorn Helgaas:
 "Some fixes for v3.8.  They include a fix for the new SR-IOV sysfs
  management support, an expanded quirk for Ricoh SD card readers, a
  Stratus DMI quirk fix, and a PME polling fix."

* tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
  PCI/PM: Do not suspend port if any subordinate device needs PME polling
  PCI: Add PCIe Link Capability link speed and width names
  PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
  PCI: Remove spurious error for sriov_numvfs store and simplify flow

Commit 56c176c9 ("UAPI: strip the _UAPI prefix from header guards
during header installation") strips the _UAPI prefix from header guards,
but only if there's a single space between the cpp directive and the
label.

Make it more flexible and able to handle tabs and multiple white space
characters.
Signed-off-by: David Howells <dhowell@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>