At present the code to check in kdump kernel was not disabling
allocation of resources when CONFIG_CHELSIO_T4_DCB is defined, move the
code outside #defines so that it gets disabled irrespective of #define,
when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.

Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG.  A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.

At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.

While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].

Fixes: 312e0676 ("qede: Utilize xmit_more")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter updates for your net tree,
they are:

1) Dump only conntrack that belong to this namespace via /proc file.
   This is some fallout from the conversion to single conntrack table
   for all netns, patch from Liping Zhang.

2) Missing MODULE_ALIAS_NF_LOGGER() for the ARP family that prevents
   module autoloading, also from Liping Zhang.

3) Report overquota event to the right netnamespace, again from Liping.

4) Fix tproxy listener sk refcount that leads to crash, from
   Eric Dumazet.

5) Fix racy refcounting on object deletion from nfnetlink and rule
   removal both for nfacct and cttimeout, from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In general, when we want to delete a netns, cttimeout_net_exit will
be called before ipt_unregister_table, i.e. before ctnl_timeout_put.

But after call kfree_rcu in cttimeout_net_exit, we will still decrease
the timeout object's refcnt in ctnl_timeout_put, this is incorrect,
and will cause a use after free error.

It is easy to reproduce this problem:
  # while : ; do
  ip netns add xxx
  ip netns exec xxx nfct add timeout testx inet icmp timeout 200
  ip netns exec xxx iptables -t raw -p icmp -I OUTPUT -j CT --timeout testx
  ip netns del xxx
  done

  =======================================================================
  BUG kmalloc-96 (Tainted: G    B       E  ): Poison overwritten
  -----------------------------------------------------------------------
  INFO: 0xffff88002b5161e8-0xffff88002b5161e8. First byte 0x6a instead of
  0x6b
  INFO: Allocated in cttimeout_new_timeout+0xd4/0x240 [nfnetlink_cttimeout]
  age=104 cpu=0 pid=3330
  ___slab_alloc+0x4da/0x540
  __slab_alloc+0x20/0x40
  __kmalloc+0x1c8/0x240
  cttimeout_new_timeout+0xd4/0x240 [nfnetlink_cttimeout]
  nfnetlink_rcv_msg+0x21a/0x230 [nfnetlink]
  [ ... ]

So only when the refcnt decreased to 0, we call kfree_rcu to free the
timeout object. And like nfnetlink_acct do, use atomic_cmpxchg to
avoid race between ctnl_timeout_try_del and ctnl_timeout_put.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Suppose that we input the following commands at first:
  # nfacct add test
  # iptables -A INPUT -m nfacct --nfacct-name test

And now "test" acct's refcnt is 2, but later when we try to delete the
"test" nfacct and the related iptables rule at the same time, race maybe
happen:
      CPU0                                    CPU1
  nfnl_acct_try_del                      nfnl_acct_put
  atomic_dec_and_test //ref=1,testfail          -
       -                                 atomic_dec_and_test //ref=0,testok
       -                                 kfree_rcu
  atomic_inc //ref=1                            -

So after the rcu grace period, nf_acct will be freed but it is still linked
in the nfnl_acct_list, and we can access it later, then oops will happen.

Convert atomic_dec_and_test and atomic_inc combinaiton to one atomic
operation atomic_cmpxchg here to fix this problem.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull networking fixes from David Miller:

 1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
    Fietkau.

 2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.

 3) Fix some tg3 ethtool logic bugs, and one that would cause no
    interrupts to be generated when rx-coalescing is set to 0.  From
    Satish Baddipadige and Siva Reddy Kallam.

 4) QLCNIC mailbox corruption and napi budget handling fix from Manish
    Chopra.

 5) Fix fib_trie logic when walking the trie during /proc/net/route
    output than can access a stale node pointer.  From David Forster.

 6) Several sctp_diag fixes from Phil Sutter.

 7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.

 8) Checksum fixup fixes in bpf from Daniel Borkmann.

 9) Memork leaks in nfnetlink, from Liping Zhang.

10) Use after free in rxrpc, from David Howells.

11) Use after free in new skb_array code of macvtap driver, from Jason
    Wang.

12) Calipso resource leak, from Colin Ian King.

13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.

14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.

15) Fix lockdep splats in macsec, from Sabrina Dubroca.

16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
    handling.

17) Various tc-action bug fixes, from CONG Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  net_sched: allow flushing tc police actions
  net_sched: unify the init logic for act_police
  net_sched: convert tcf_exts from list to pointer array
  net_sched: move tc offload macros to pkt_cls.h
  net_sched: fix a typo in tc_for_each_action()
  net_sched: remove an unnecessary list_del()
  net_sched: remove the leftover cleanup_a()
  mlxsw: spectrum: Allow packets to be trapped from any PG
  mlxsw: spectrum: Unmap 802.1Q FID before destroying it
  mlxsw: spectrum: Add missing rollbacks in error path
  mlxsw: reg: Fix missing op field fill-up
  mlxsw: spectrum: Trap loop-backed packets
  mlxsw: spectrum: Add missing packet traps
  mlxsw: spectrum: Mark port as active before registering it
  mlxsw: spectrum: Create PVID vPort before registering netdevice
  mlxsw: spectrum: Remove redundant errors from the code
  mlxsw: spectrum: Don't return upon error in removal path
  i40e: check for and deal with non-contiguous TCs
  ixgbe: Re-enable ability to toggle VLAN filtering
  ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
  ...

Cong Wang says:

====================
net_sched: tc action fixes and updates

This patchset fixes a few regressions caused by the previous
code refactor and more. Thanks to Jamal for catching them!

Note, patch 3/7 and 4/7 are not strictly necessary for this patchset,
I just want to carry them together.

---
v4: adjust an indention for Jamal
    add two more patches

v3: avoid list for fast path, suggested by Jamal

v2: replace flex_array with regular dynamic array
    keep tcf_action_stats_update() in act_api.h
    fix macro typos found by Amir
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The act_police uses its own code to walk the
action hashtable, which leads to that we could
not flush standalone tc police actions, so just
switch to tcf_generic_walker() like other actions.

(Joint work from Roman and Cong.)
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jamal reported a crash when we create a police action
with a specific index, this is because the init logic
is not correct, we should always create one for this
case. Just unify the logic with other tc actions.

Fixes: a03e6fe5 ("act_police: fix a crash during removal")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.

The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.

Fixes: a85a970a ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct tcf_exts belongs to filters, should not be visible
to plain tc actions.

Cc: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is harmless because all users pass 'a' to this macro.

Fixes: 00175aec ("net/sched: Macro instead of CONFIG_NET_CLS_ACT ifdef")
Cc: Amir Vadai <amir@vadai.me>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This list_del() for tc action is not needed actually,
because we only use this list to chain bulk operations,
therefore should not be carried for latter operations.

Fixes: ec0595cc ("net_sched: get rid of struct tcf_common")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After refactoring tc_action into tcf_common, we no
longer need to cleanup temporary "actions" in list,
they are permanently stored in the hashtable.

Fixes: a85a970a ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-08-16

This series contains fixes to e1000e, igb, ixgbe and i40e.

Kshitiz Gupta provides a fix for igb to resolve the PHY delay compensation
math in several functions.

Jarod Wilson provides a fix for e1000e which had to broken up into 2
patches, first is prepares the driver for expanding the list of NICs
that have occasional ~10 hour clock jumps when being used for PTP.
Second patch actually fixes i218 silicon which has been experiencing
the clock jumps while using PTP.

Alex provides 2 patches for ixgbe now that he is back at Intel.  First
fixes setting VLNCTRL.VFE bit, which was left unchanged in earlier patches
which resulted in disabling VLAN filtering for all the VFs.  Second
corrects the support for disabling the VLAN tag filtering via the
feature bit.

Lastly, David fixes i40e which was causing a kernel panic when
non-contiguous traffic classes or traffic classes not starting with TC0,
were configured on a link partner switch.  To fix this, changed the
logic when determining the total number of TCs enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: IPv4 UC router fixes

Ido says:
Patches 1-3 fix a long standing problem in the driver's init sequence,
which manifests itself quite often when routing daemons try to configure
an IP address on registered netdevs that don't yet have an associated
vPort.

Patches 4-9 add missing packet traps for the router to work properly and
also fix ordering issue following the recent changes to the driver's init
sequence.

The last patch isn't related to the router, but fixes a general problem
in which under certain conditions packets aren't trapped to CPU.

v1->v2:
- Change order of patch 7
- Add patch 6 following Ilan's comment
- Add patchset name and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:

(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
 Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
 Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)

Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.

Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.

Fixes: 8e8dfe9f ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().

Fixes: 14d39461 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ralue pack function needs to set op, otherwise it is 0 for add always.

Fixes: d5a1c749 ("mlxsw: reg: Add Router Algorithmic LPM Unicast Entry Register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).

Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.

For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.

Fixes: 99724c18 ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the following traps:

1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.

2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.

3) OSPF packets.

Fixes: 7b27ce7b ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit bbf2a475 ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.

Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.

Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.

Fixes: bbf2a475 ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.

Therefore, we must create the PVID vPort before registering the
netdevice.

Fixes: 99724c18 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.

In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.

Fixes: 99724c18 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.

Instead, we should keep trying to free as much resources as possible in
a best effort mode.

Remove the error message as well, since we already get these from the
EMAD transaction code.

Fixes: 99724c18 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_lookup_listener() and inet6_lookup_listener() no longer
take a reference on the found listener.

This minimal patch adds back the refcounting, but we might do
this differently in net-next later.

Fixes: 3b24d854 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Reported-and-tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We should report the over quota message to the right net namespace
instead of the init netns.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull power supply fixes from Sebastian Reichel.

* tag 'for-v4.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power_supply: tps65217-charger: fix missing platform_set_drvdata()
  power: reset: hisi-reboot: Unmap region obtained by of_iomap
  power: reset: reboot-mode: fix build error of missing ioremap/iounmap on UM
  power: supply: max17042_battery: fix model download bug.

Otherwise, if nfnetlink_log.ko is not loaded, we cannot add rules
to log packets to the userspace when we specify it with arp family,
such as:

  # nft add rule arp filter input log group 0
  <cmdline>:1:1-37: Error: Could not process rule: No such file or
  directory
  add rule arp filter input log group 0
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We should skip the conntracks that belong to a different namespace,
otherwise other unrelated netns's conntrack entries will be dumped via
/proc/net/nf_conntrack.

Fixes: 56d52d48 ("netfilter: conntrack: use a single hashtable for all namespaces")
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull virtio/vhost fixes from Michael Tsirkin:
 - test fixes
 - a vsock fix

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  tools/virtio: add dma stubs
  vhost/test: fix after swiotlb changes
  vhost/vsock: drop space available check for TX vq
  ringtest: test build fix

Pull s390 fixes from Martin Schwidefsky:
 "A couple of bug fixes, minor cleanup and a change to the default
  config"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/dasd: fix failing CUIR assignment under LPAR
  s390/pageattr: handle numpages parameter correctly
  s390/dasd: fix hanging device after clear subchannel
  s390/qdio: avoid reschedule of outbound tasklet once killed
  s390/qdio: remove checks for ccw device internal state
  s390/qdio: fix double return code evaluation
  s390/qdio: get rid of spin_lock_irqsave usage
  s390/cio: remove subchannel_id from ccw_device_private
  s390/qdio: obtain subchannel_id via ccw_device_get_schid()
  s390/cio: stop using subchannel_id from ccw_device_private
  s390/config: make the vector optimized crc function builtin
  s390/lib: fix memcmp and strstr
  s390/crc32-vx: Fix checksum calculation for small sizes
  s390: clarify compressed image code path

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - Missing ULL suffixes for 64-bit constants in sha3.
   - Two caam AEAD regressions.
   - Bogus setkey hooks in non-hmac caam hashes.
   - Missing kbuild dependency for powerpc crc32c"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: caam - fix non-hmac hashes
  crypto: powerpc - CRYPT_CRC32C_VPMSUM should depend on ALTIVEC
  crypto: caam - defer aead_set_sh_desc in case of zero authsize
  crypto: caam - fix echainiv(authenc) encrypt shared descriptor
  crypto: sha3 - Add missing ULL suffixes for 64-bit constants

The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.

To fix this, the patch changes the logic when determining
the total number of TCs enabled.  Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled.  Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous.  If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit.  This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.

Fixes: b83e3010 ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV.  This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.

Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.

Fixes: 16369564 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull pin control fixes from Linus Walleij:
 "Here are a few pin control fixes for the v4.8 series, nothing special
  about them:

   - Add the missing <linux/io.h> header to the Intel Merrifield driver
     to get rid of build mess.

   - Drop two instances of pinctrl_unregister() called for drivers using
     devm_* resource management.

   - Remove the default debounce time for the AMD driver"

* tag 'pinctrl-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: intel: merrifield: Add missed header
  pinctrl/amd: Remove the default de-bounce time
  pinctrl: pistachio: Drop pinctrl_unregister for devm_ registered device
  pinctrl: meson: Drop pinctrl_unregister for devm_ registered device

I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>