Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.21

Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.

Major changes:

ath10k

* add amsdu support for QCA6174 monitor mode

* report tx rate using the new ieee80211_tx_rate_update() API

* wcn3990 support is not experimental anymore

iwlwifi

* support for FW version 43 for 9000 and 22000 series

brcmfmac

* add support for CYW43012 SDIO chipset

* add the raw 4354 PCIe device ID for unprogrammed Cypress boards

mwifiex

* add NL80211_STA_INFO_RX_BITRATE support

mt76

* use the same firmware for mt76x2e and mt76x2u

* mt76x0e survey support

* more unification between mt76x2 and mt76x0

* mt76x0e AP mode support

* mt76x0e DFS support

* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't need extern prefix before function prototypes.
Checkpatch has complained about this for a couple of years.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
net: ipv4: Prevent user triggerable warning

Patch #1 prevents a user triaggerable warning in the flow dissector by
setting 'skb->dev' in skbs used for IPv4 output route get requests.

Patch #2 adds a test case that triggers the warning without the first
patch.

I have audited all the RTM_GETROUTE handlers and could not find any
other callpath where an skb is passed to the flow dissector with both
'skb->dev' and 'skb->sk' cleared.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Without previous patch a warning would be generated upon multipath route
get when FIB multipath hash policy is to use a 5-tuple for multipath
hash calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user requests to resolve an output route, the kernel synthesizes
an skb where the relevant parameters (e.g., source address) are set. The
skb is then passed to ip_route_output_key_hash_rcu() which might call
into the flow dissector in case a multipath route was hit and a nexthop
needs to be selected based on the multipath hash.

Since both 'skb->dev' and 'skb->sk' are not set, a warning is triggered
in the flow dissector [1]. The warning is there to prevent codepaths
from silently falling back to the standard flow dissector instead of the
BPF one.

Therefore, instead of removing the warning, set 'skb->dev' to the
loopback device, as its not used for anything but resolving the correct
namespace.

[1]
WARNING: CPU: 1 PID: 24819 at net/core/flow_dissector.c:764 __skb_flow_dissect+0x314/0x16b0
...
RSP: 0018:ffffa0df41fdf650 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8bcded232000 RCX: 0000000000000000
RDX: ffffa0df41fdf7e0 RSI: ffffffff98e415a0 RDI: ffff8bcded232000
RBP: ffffa0df41fdf760 R08: 0000000000000000 R09: 0000000000000000
R10: ffffa0df41fdf7e8 R11: ffff8bcdf27a3000 R12: ffffffff98e415a0
R13: ffffa0df41fdf7e0 R14: ffffffff98dd2980 R15: ffffa0df41fdf7e0
FS:  00007f46f6897680(0000) GS:ffff8bcdf7a80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055933e95f9a0 CR3: 000000021e636000 CR4: 00000000001006e0
Call Trace:
 fib_multipath_hash+0x28c/0x2d0
 ? fib_multipath_hash+0x28c/0x2d0
 fib_select_path+0x241/0x32f
 ? __fib_lookup+0x6a/0xb0
 ip_route_output_key_hash_rcu+0x650/0xa30
 ? __alloc_skb+0x9b/0x1d0
 inet_rtm_getroute+0x3f7/0xb80
 ? __alloc_pages_nodemask+0x11c/0x2c0
 rtnetlink_rcv_msg+0x1d9/0x2f0
 ? rtnl_calcit.isra.24+0x120/0x120
 netlink_rcv_skb+0x54/0x130
 rtnetlink_rcv+0x15/0x20
 netlink_unicast+0x20a/0x2c0
 netlink_sendmsg+0x2d1/0x3d0
 sock_sendmsg+0x39/0x50
 ___sys_sendmsg+0x2a0/0x2f0
 ? filemap_map_pages+0x16b/0x360
 ? __handle_mm_fault+0x108e/0x13d0
 __sys_sendmsg+0x63/0xa0
 ? __sys_sendmsg+0x63/0xa0
 __x64_sys_sendmsg+0x1f/0x30
 do_syscall_64+0x5a/0x120
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: d0e13a14 ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing indirect access in the Ocelot chip, a command is setup,
issued and then we need to poll until the result is ready. The polling
timeout is specified in milliseconds in the datasheet and not in
register access attempts.
It is not a bug on the currently supported platform, but we observed
that the code does not work properly on other platforms that we want to
support as the timing requirements there are different.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the stray semicolon means that the final term in the addition
is being missed.  Fix this by removing it. Cleans up clang warning:

net/core/neighbour.c:2821:9: warning: expression result unused [-Wunused-value]

Fixes: 82cbb5c6 ("neighbour: register rtnl doit handler")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports.  In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60.  Port 6 is the host port.

Setting a zero value can be used to stop port from receiving.

However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate.  This does not apply to
multicast and broadcast addresses though.  To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.

Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.

Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When resolving the conflict wrt. the vxlan_fdb_update call
in vxlan_changelink() I made the last argument false instead
of true.

Fix this.
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2018-12-19

This series adds some misc updates and the support for tunnels over VLAN
tc offloads.

From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock

From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128

From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.

Patch 4 avoids crash for TC flow with egress upper devices

Patch 5 refactors tunnel routing devs into a helper function

Patch 6 avoids crash for TC encap flows with vlan on underlay

Patches 7-8 refactor encap tunnel header preparing code.

Patch 9 adds support for building VLAN tagged ETH header.

Patch 10 adds support for tunnel routing to VLAN device.

From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Two usability improvements

This patchset contains two small improvements in the mlxsw driver. The
first one, in patches #1-#2, relieves the user from the need to
configure a VLAN interface and only later the corresponding VXLAN
tunnel. The issue is explained in detail in the first patch.

The second improvement is described below and allows the user to make
use of VID 1 by having the driver use the reserved 4095 VID for untagged
traffic.

VLAN entries on a given port can be associated with either a bridge or a
router. For example, if swp1.10 is assigned an IP address and swp1.20 is
enslaved to a VLAN-unaware bridge, then both {Port 1, VID 10} and {Port
1, VID 20} would be associated with a filtering identifier (FID) of the
correct type.

In case swp1 itself is assigned an IP address or enslaved to a
VLAN-unaware bridge, then a FID would be associated with {Port 1, VID
1}. Using VID 1 for this purpose means that VLAN devices with VID 1
cannot be created over mlxsw ports, as this VID is (ab)used as the
default VLAN.

Instead of using VID 1 for this purpose, we can use VID 4095 which is
reserved for internal use and cannot be configured by either the 8021q
or the bridge driver.

Patches #3-#7 perform small and non-functional changes that finally
allow us to switch to VID 4095 as the default VID in patch #8.

Patch #9 removes the limitation about creation of VLAN devices with VID
1 over mlxsw ports.

Patches #10-#11 add test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.

Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patches made it possible to create VLAN devices with VID 1 over
mlxsw ports. Adjust the test to verify such an operation succeeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VID 1 is not reserved anymore, so remove the check that prevented the
creation of VLAN devices with this VID over mlxsw ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.

The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.

Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.

The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function allows flushing all the existing VLAN entries on a port. It
is invoked when a port is destroyed and when it is unlinked from a LAG.
In the latter case, when moving to the new default VLAN, there will not
be a need to destroy the default VLAN entry.

Therefore, add an argument that allows to control whether the default
port VLAN should be destroyed or not. Currently it is always set to
'true'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the driver does not set the port's PVID when initializing a
new port. This is because the driver is using VID 1 as PVID which is the
firmware default.

Subsequent patches are going to change the PVID the driver is setting
when initializing a new port.

Prepare for that by explicitly setting the port's PVID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).

Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patch added the ability to offload a VXLAN tunnel used for L3
VNI when it is present in the VLAN-aware bridge before the corresponding
VLAN interface is configured. This patch adds a test case to verify
that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.

In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.

The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.

Instead, call into the bridge code which will check if NVE should be
enabled on the FID.

This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-12-20

This series contains updates to e100, igb, ixgbe, i40e and ice drivers.

I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics.  This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.

Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.

Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.

YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.

Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.

Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.

Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.

Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in.  This was due to the
driver not setting PME during runtime suspend.

Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the mii_bus callbacks to address the entire clause 22/45 address
space.  Enables userspace to poke switch registers instead of a single
PHY address.

The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock.  This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.

While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.

Since commit 42eca230 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.

To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.

Fixes: 42eca230 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.

See commit 13a8cd19 ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Out of bound read reported by KASan.

i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as

  tbl->entry_size + dev->neigh_priv_len

where "dev" is a net_device.

But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
 e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.

Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some pointers to the definition of the CBS algorithm, and some
notes about the limits of its implementation in the i210 family of
controllers.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.

The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.

The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
 on CPU0.

In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.

CC: Bernhard Kaindl  <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ath.git patches for 4.21. Major changes:

ath10k

* add amsdu support for QCA6174 monitor mode

* report tx rate using the new ieee80211_tx_rate_update() API

* wcn3990 support is not experimental anymore

Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".

Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.

This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.

Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.

    1. Peer creation:
        ath10k_peer_create()
            =>ath10k_wmi_peer_create()
                =>ath10k_wait_for_peer_created()
                ...

        # another kernel path, RX from firmware
        ath10k_htt_t2h_msg_handler()
        =>ath10k_peer_map_event()
                =>wake_up()
                # ar->peer_map[id] = peer //add peer to map

        #wake up original path from waiting
                ...
                # peer->sta = sta //sta assignment

    2.  RX path of statistics
        ath10k_htt_t2h_msg_handler()
            =>ath10k_update_per_peer_tx_stats()
                =>ath10k_htt_fetch_peer_stats()
                # peer->sta //sta accessing

Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.

Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>