* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix offset calculation in compute_size()
  rtc: rtc-starfire fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
  MAINTAINERS: add netdev to ATM
  ATM: horizon, fix hrz_probe fail path
  pppol2tp: Add missing sock_put() in pppol2tp_release()
  net: Fix soft lockups/OOM issues w/ unix garbage collector
  macvlan: don't broadcast PAUSE frames to macvlan devices
  Phonet: fix oops in phonet_address_del() on non-Phonet device
  netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock
  sungem: Fix PCS_MIICTRL register write in gem_init_phy().
  net: make skb_truesize_bug() call WARN()
  net: hp-plus uses eip_poll
  net/wireless/reg.c: fix bad WARN_ON in if statement
  ath5k: disable beacon filter when station is not associated
  ath5k: fix Security issue in DebugFS part of ath5k
  ath9k: correct expected max RX buffer size
  ath9k: Fix SW-IOMMU bounce buffer starvation
  mac80211 : Fix setting ad-hoc mode and non-ibss channel
  iwlagn: fix DMA sync
  phylib: Add Vitesse VSC8221 SGMII PHY
  rose: zero length frame filtering in af_rose.c
  bridge: netfilter: fix update_pmtu crash with GRE
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Update defconfigs for 2.6.28-rc7
  macfb: Do not overflow fb_fix_screeninfo.id

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  alim15x3: fix sparse warning
  ide: remove dead code from drive_is_ready()
  ide: fix build for DEBUG_PM
  ide: respect current DMA setting during resume
  ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]
  amd74xx: workaround unreliable AltStatus register for nVidia controllers
  ide: fix the ide_release_lock imbalance

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] stex: switch to block timeout
  [SCSI] make scsi_eh_try_stu use block timeout
  [SCSI] megaraid_sas: switch to block timeout
  [SCSI] ibmvscsi: switch to block timeout
  [SCSI] aacraid: switch to block timeout
  [SCSI] zfcp: prevent double decrement on host_busy while being busy
  [SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
  [SCSI] zfcp: eliminate race between validation and locking
  [SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
  [SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
  [SCSI] zfcp: Fix opening of wka ports
  [SCSI] zfcp: fix remote port status check
  [SCSI] fc_transport: fix old bug on bitflag definitions
  [SCSI] Fix hang in starved list processing

This fixes the MN10300 kernel module linking to match the toolchain.  RELA
relocs don't use the value at the location being relocated.  This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id.  We were writing that directly
into the HW register.

We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Count the insertion of new pages in the statistics used to drive the
pageout scanning code.  This should help the kernel quickly evict
streaming file IO.

We count on the fact that new file pages start on the inactive file LRU
and new anonymous pages start on the active anon list.  This means
streaming file IO will increment the recent scanned file statistic, while
leaving the recent rotated file statistic alone, driving pageout scanning
to the file LRUs.

Pageout activity does its own list manipulation.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: Gene Heskett <gene.heskett@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.

On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.

This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.

[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The previous patch from Alan Cox ("nfsd: fix vm overcommit crash",
commit 731572d3) fixed the problem where
knfsd crashes on exported shmemfs objects and strict overcommit is set.

But the patch forgot supporting the case when CONFIG_SECURITY is
disabled.

This patch copies a part of his fix which is mainly for detecting a bug
earlier.
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Junjiro R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Fix this sparse warning:

  drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We guarantee 400ns delay at the time of issuing the command.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also while at it:

* Drop unused arguments from ide_complete_power_step().

* Move DEBUG_PM printk() from ide_end_drive_cmd() to
  ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Should fix kernel.org bug #10225:
http://bugzilla.kernel.org/show_bug.cgi?id=10225Reported-by: Matthias B. <haferfrost@web.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode.  In order to achieve this:

* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.

* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
  driver for nVidia controllers in Compatibility Mode.

* Teach actual_try_to_identify() and drive_is_ready() about the new flag.

This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).

[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
  and distributions use) it never worked correctly. ]

Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.

More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659
http://bugzilla.kernel.org/show_bug.cgi?id=10216Reported-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_release_lock() spits out lots of:

	ide_release_lock: bug

warnings on Atari Falcon.

Fix the ide_release_lock imbalance.
Signed-off-by: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't overflow the 16-character fb_fix_screeninfo id string (fixes some 
console erasing and blanking artifacts). Have the ID default to "Unknown" 
on machines with no built-in video and no nubus devices. Check for 
fb_alloc_cmap failure.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (25 commits)
  em28xx: remove backward compat macro added on a previous fix
  V4L/DVB (9748): em28xx: fix compile warning
  V4L/DVB (9743): em28xx: fix oops audio
  V4L/DVB (9742): em28xx-alsa: implement another locking schema
  V4L/DVB (9732): sms1xxx: use new firmware for Hauppauge WinTV MiniStick
  V4L/DVB (9691): gspca: Move the video device to a separate area.
  V4L/DVB (9690): gspca: Lock the subdrivers via module_get/put.
  V4L/DVB (9689): gspca: Memory leak when disconnect while streaming.
  V4L/DVB (9668): em28xx: fix a race condition with hald
  V4L/DVB (9664): af9015: don't reconnect device in USB-bus
  V4L/DVB (9647): em28xx: void having two concurrent control URB's
  V4L/DVB (9646): em28xx: avoid allocating/dealocating memory on every control urb
  V4L/DVB (9645): em28xx: Avoid memory leaks if registration fails
  V4L/DVB (9639): Make dib0700 remote control support work with firmware v1.20
  V4L/DVB (9635): v4l: s2255drv fix firmware test on big-endian
  V4L/DVB (9634): Make sure the i2c gate is open before powering down tuner
  V4L/DVB (9632): make em28xx aux audio input work
  V4L/DVB (9631): Make s2api work for ATSC support
  V4L/DVB (9627): em28xx: Avoid i2c register error for boards without eeprom
  V4L/DVB (9608): Fix section mismatch warning for dm1105 during make
  ...

drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix module removal bugs of i82875p_edac.  Also i82975x_edac code seems to
have the same module removal bugs as in i82875p_edac.

The problems were:

1. In module removal i82875p_remove_one() is never called.

   Variable i82875p_registered is newer changed from 1, which
   guarantees i82875p_remove_one() is not called (and even if it were
   called, it would be called in wrong order).

   As a result, the edac_mc workque is not stopped and keeps probing.
   If kernel debugging options are not enabled, user may not notice
   anything going wrong.

   if debugging options are enabled and I do "rmmod i82875p_edac", I
   get:

      edac debug: edac_pci_workq_function() checking
      BUG: unable to handle kernel paging request at f882d16f
      ...
      call trace:
       [<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core]
       [<c0233974>] ? run_workqueue+0xd7/0x1a5
       [<c023392f>] ? run_workqueue+0x92/0x1a5
       [<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core]
       [<c0233af9>] ? worker_thread+0xb7/0xc3
       [<c0236a7b>] ? autoremove_wake_function+0x0/0x33
       [<c0233a42>] ? worker_thread+0x0/0xc3
       [<c0236809>] ? kthread+0x3b/0x61
       [<c02367ce>] ? kthread+0x0/0x61
       [<c0204587>] ? kernel_thread_helper+0x7/0x10

   Fix for this is to get rid of needles variable i82875p_registered
   altogether and run i82875p_remove_one() *before*
   pci_unregister_driver().

2. edac_mc_del_mc() uses mci after freeing mci

   edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device().  The
   kobject refcount of mci drops to 0 and mci is freed.  After this
   mci is accessed via debug print and i82875p_remove_one() still
   uses mci->pvt and tries to free mci again with edac_mc_free().

   The fix for this is add kobject_get(&mci->edac_mci_kobj) after
   edac_mc_alloc(). Then the mci is still available after returning
   from edac_mc_del_mc() with refcount 1, and mci->pvt is still
   available. When i82875p_remove_one() finally calls edac_mc_free(),
   this will cause kobject_put() and mci is released properly.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When I do "modprobe i82875p_edac" on my Asus P4C800 MB on kernels 2.6.26
or later, the module load fails due to BAR 0 collision.  On 2.6.25 the
module loads just fine.

The overflow device on the MB seems to be hidden and its resources are not
allocated at normal PCI bus init.  Log shows the missing resource problem:

  EDAC DEBUG: i82875p_probe1()
  PCI: 0000:00:06.0 reg 10 32bit mmio: [fecf0000, fecf0fff]
  pci 0000:00:06.0: device not available because of BAR 0
[0xfecf0000-0xfecf0fff] collisions
  EDAC i82875p: i82875p_setup_overfl_dev(): Failed to enable overflow
device

The patch below fixes this by calling pci_bus_assign_resources() after
the overflow device is revealed and added to the bus. With this patch
I am again able to load and use the module.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The commit aef7db4b fixed the problem with
recursive locking in fb blanking code if blank is caused by user setting
the /sys/class/graphics/fb*/blank.  However this broke the fbcon timeout
blanking.

If you use a driver that defines ->fb_blank operation and at the same time
that driver relies on other driver (e.g.  backlight or lcd class) to blank
the screen, when the fbcon times out and tries to blank the fb, it will
call only fb driver blanker and won't notify the other driver.  Thus FB
output is disabled, but the screen isn't blanked.

Restore fbcon blanking and at the same time apply the proper fix for the
above problem: if fbcon_blank is called with FBINFO_FLAG_USEREVENT, we are
already called through notification from fb_blank, thus we don't have to
blank the fb again.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-doc handles macros now (it has for quite some time), so change the
ntfs_debug() macro's kernel-doc to be just before the macro instead of
before a phony function prototype.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The method for listing varargs in kernel-doc notation is:
 * @...: these arguments are printed by the @fmt argument

but scripts/kernel-doc is confused:  it always lists varargs as:
	...	variable arguments
and ignores the @...: line's description, but then prints that
line after the list of function parameters as though it's
not part of the function parameters.

This patch makes kernel-doc print the supplied @...  description if it is
present; otherwise a boilerplate "variable arguments" is printed.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

2nd part of the fixes needed for
http://bugzilla.kernel.org/show_bug.cgi?id=11796.

When the idr tree is either grown or shrunk, then the update to the number
of layers and the top pointer were not atomic.  This race caused crashes.

The attached patch fixes that by replicating the layers counter in each
layer, thus idr_find doesn't need idp->layers anymore.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Clement Calmels <cboulte@gmail.com>
Cc: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Pierre Peiffer <peifferp@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

- pci_map_sg/dma_map_sg are used with a scatter gather list that doesn't
  come from the block layer (e.g.  some network drivers do).

- how IOMMUs merge adjacent elements of the scatter/gather list is
  independent of how the block layer determines sees elements.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the error handling in sys_mmap2().  Currently, if the pgoff check
fails, fput() might have to be called (which it isn't), so do the pgoff
check first, before fget() is called.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The description for 'D' was missing in the comment...  (causing me a
minute of WTF followed by looking at more of the code)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The engine on some radeon variants locks up if color expansion is called
for non aligned source data.  This patch enables a feature of the core
fbdev to request aligned input pixmaps and uses the HW clipping engine to
clip the output to the requested size

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11875Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The spi master driver must have num_chipselect set to allow the bus to
initialise.  Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver.  Fix this
by using spi_master_get_devdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.  Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Corrects spi_imx driver oops during initialization/probing: can't use
drv_data before it's allocated.
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It has been thought that the per-user file descriptors limit would also
limit the resources that a normal user can request via the epoll
interface.  Vegard Nossum reported a very simple program (a modified
version attached) that can make a normal user to request a pretty large
amount of kernel memory, well within the its maximum number of fds.  To
solve such problem, default limits are now imposed, and /proc based
configuration has been introduced.  A new directory has been created,
named /proc/sys/fs/epoll/ and inside there, there are two configuration
points:

  max_user_instances = Maximum number of devices - per user

  max_user_watches   = Maximum number of "watched" fds - per user

The current default for "max_user_watches" limits the memory used by epoll
to store "watches", to 1/32 of the amount of the low RAM.  As example, a
256MB 32bit machine, will have "max_user_watches" set to roughly 90000.
That should be enough to not break existing heavy epoll users.  The
default value for "max_user_instances" is set to 128, that should be
enough too.

This also changes the userspace, because a new error code can now come out
from EPOLL_CTL_ADD (-ENOSPC).  The EMFILE from epoll_create() was already
listed, so that should be ok.

[akpm@linux-foundation.org: use get_current_user()]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <stable@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send.  The PSC controller holds SS low until the flag is set.

However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer.  This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals.  Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I saw a kernel oops in spidev_remove() when a spidev device was registered
and I unloaded the SPI master driver:

Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01c0c50
Oops: Kernel access of bad area, sig: 11 [#1]
CDSPR
Modules linked in: spi_ppc4xx(-)
NIP: c01c0c50 LR: c01bf9e4 CTR: c01c0c34
REGS: cec89c30 TRAP: 0300   Not tainted  (2.6.27.3izt)
MSR: 00021000 <ME>  CR: 24000228  XER: 20000007
DEAR: 00000004, ESR: 00800000
TASK = cf889040[2070] 'rmmod' THREAD: cec88000
GPR00: 00000000 cec89ce0 cf889040 cec8e000 00000004 cec8e000 ffffffff 00000000
GPR08: 0000001c c0336380 00000000 c01c0c34 00000001 1001a338 100e0000 100df49c
GPR16: 100b54c0 100df49c 100ddd20 100f05a8 100b5340 100efd68 00000000 00000000
GPR24: 100ec008 100f0428 c0327788 c0327794 cec8e0ac cec8e000 c0336380 00000000
NIP [c01c0c50] spidev_remove+0x1c/0xe4
LR [c01bf9e4] spi_drv_remove+0x2c/0x3c
Call Trace:
[cec89d00] [c01bf9e4] spi_drv_remove+0x2c/0x3c
[cec89d10] [c01859a0] __device_release_driver+0x78/0xb4
[cec89d20] [c0185ab0] device_release_driver+0x28/0x44
[cec89d40] [c0184be8] bus_remove_device+0xac/0xd8
[cec89d60] [c0183094] device_del+0x100/0x194
[cec89d80] [c0183140] device_unregister+0x18/0x30
[cec89da0] [c01bf30c] __unregister+0x20/0x34
[cec89db0] [c0182778] device_for_each_child+0x38/0x74
[cec89de0] [c01bf2d0] spi_unregister_master+0x28/0x44
[cec89e00] [c01bfeac] spi_bitbang_stop+0x1c/0x58
[cec89e20] [d908a5e0] spi_ppc4xx_of_remove+0x24/0x7c [spi_ppc4xx]
[...]

IMHO a call to spi_set_drvdata() is missing in spidev_probe(). The patch
below helped.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>